Page 1
Ultra-High Efficiency RO/DI
(MC-RODI-400UHE-20)
v2 2014-09-05
OWNER’S MANUAL
&
INSTALLATION INSTRUCTIONS
WARNING
Please read carefully before proceeding with installation. Failure
to follow any attached instructions or operating parameter may
lead to the product’s failure and possible damage to property.
Page 2
SpectraPure
®
Thank You for your purchase of a SpectraPure® System. With proper installation and maintenance, this system
will provide you with high quality water for years to come. All SpectraPure® products are rigorously tested by us
for safety and reliability. If you have any questions or concerns, please contact our customer service department
at 1.800.685.2783 or refer to our online troubleshooting at www.spectrapure.com.
TABLE OF CONTENTS
Operational Specifications 3
Contents of UHE Water Systems 3
Operation Description (how the system functions) 4
Preparation
Choosing the best Mounting Location 5
Tools recommended for installation 5
Introduction to Push Fittings 5
System Diagram 6
Setup Procedures
Installation of Floats for the Pure Water Flush Cycle Tank 7
Pressure Adjustment with Regulator 8
Adjusting Concentrate to Purified Water Ratio 8
Connecting Bulkhead Fittings 9
Final Connection 9
Maintenance Procedures
Shelf Life of Filters 10
Sediment Prefilter Replacement 10
Carbon Block Prefilter Replacement 11
Reverse Osmosis Membrane Rejection Diagnostics 11
Reverse Osmosis Membrane Performance Testing 12
Reverse Osmosis Membrane Replacement 12-14
Tips for long membrane life 14
Deionization Cartridge Maintenance and Replacement 14
Warranty Information 15
Troubleshooting Guide 16
Relacement Parts List 16
Copyright © 2009-2015 by SpectraPure Inc.
ALL RIGHTS RESERVED
No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying,
recording or otherwise without the prior written permission of SpectraPure Inc.
2
SpectraPure®Inc.
2167 East Fifth St, Tempe, Arizona 85281
480.894.5437 Call us toll-free 1.800.685.2783
Page 3
SpectraPure
®
OPERATIONAL SPECIFICATIONS
RO Feed water requirements
Operating Pressure: 30 psi minimum
pH Range: 3 -11
Max. Temperature: 113°F (45°C)
Max. Feed Turbidity: 1.0 NTU
Max. Silt Density Index: 5.0 (based on 15 min. test time)
Maximum Chlorine: < 0.1 ppm
Maximum TDS: 2000 ppm
Maximum Hardness: 10 grains (170 ppm as CaCO3)
Maximum Iron: < 0.1 ppm.
Maximum Manganese: < 0.1 ppm.
Maximum Hydrogen Sulfide: 0 ppm
Langelier Saturation Index (LSI): must be negative
NOTE: MOST MUNICIPAL WATER SUPPLIES MEET THE ABOVE REQUIREMENTS. IF WELL WATER IS USED,
PLEASE MAKE SURE THAT YOU OBTAIN A WATER TEST BEFORE INSTALLATION.
CONTENTS OF UHE WATER SYSTEM
UHE System Components:
(1) 5- Stage System
- (1) Membrane (400 GPD)
- (1) 20" 0.2 Micron ZetaZorb
- (1) 20” 0.5 Micron Carbon Block Filter
- (1) 20” MaxCap® DI Cartridge
- (1) 20” SilicaBuster™ DI Cartridge
- (1) High Flow Booster Pump
- (1) Microprocessor Controller
- (1) Pressure Regulator
- (2) Liquid Filled Pressure Gauges
(1) High & Low Float Switches (with 6ft extension cable)
(1) Filter Wrench
(2) Bulkhead Fittings
Pure Water
Flush Line (1/2")
Pump
AC Power Cord
Input Feed
Water Line (1/2")
®
Sediment Filter
UHE SYSTEM DIMENSIONS:
24" W x 34" H x 8" D
1/2" BLACK LINE: Tap Water input
3/8" BLUE LINE: Product Water
3/8" YELLOW LINE: Waste Water
1/2” BLUE LINE: Pure Water Flush
400 GPD RO Membrane
(MEM- LAB -0400)
Waste Water
Line (3/8")
Product Water LIne (3/8")
Behind DI-S B-20
Sediment Filter
(SF-ZZ-0.2-ABS -20)
Carbon Filter
(CF- 0.5 - 20)
IF ANY OF THE ITEMS LISTED ABOVE ARE MISSING PLEASE CONTACT SPECTRAPURE PRIOR TO INSTALLATION.
ALL RETURNS WITHOUT RMA# WILL BE REFUSED. CLAIMS MUST BE WITHIN 10 DAYS FROM RECEIPT.
SpectraPure®Inc.
2167 East Fifth St, Tempe, Arizona 85281
480.894.5437 Call us toll-free 1.800.685.2783
MaxCap
(DI-MC-20)
SilicaBuster™ DI Cartridge
(DI-SB -20)
®
DI Cartridge
3
Page 4
SpectraPure
®
OPERATION DESCRIPTION (how the system functions)
1. First, the incoming feed water (1/2” Black line) is passed through a 0.2 micron ZetaZorb® Sediment Filter. This filter is
required to remove excess turbidity (particulate matter) that may cause the carbon block filter to become plugged.
2. The second stage of filtration is a 0.5 micron carbon block prefilter. This filter removes organics and chlorine from the
feed water that can damage the membrane.
3. The third filtration stage of the system is a high rejection thin film composite (TFC) reverse osmosis membrane. It
removes over 98% of most inorganic salts, all microorganisms and organics above 100 dalton molecular weight.
4. The fourth and fifth stage filter are our MAXCAP® DI cartridge followed by our SilicaBuster™ DI cartridge. These
two cartridges remove the remaining impurities such as silicates, phosphates, and nitrates not removed by the RO
membrane, further polishing the water to 18.2 Mohms/cm2 resistivity.
High and Low Float Operation:
1. Floats are to be mounted horizontal when dry and float up when wet.
NOTE: Pressure switches may also be used with pressure tanks. Please call for more details.)
2. When the bottom float goes dry, the input solenoid (INSOL) is opened and one second later, the Pump will turn
on.
Flush Cycle (flush cycle consumes only a couple of quarts of pure water):
1. As the system is running, a periodic sequence of flushes is performed.
2. When the top float gets wet, or every 8 hours of uninterrupted operation, the flush cycle is initiated.
3. After the flush cycle, the system shuts down if the tank is full or pauses for an hour to let the pure water soak the
membrane before continuing.
SpectraPure® Inc. assumes no responsibility for water damage due to leaks. It is
the user’s responsibility to determine that the system is leak-free.
4
SpectraPure®Inc.
2167 East Fifth St, Tempe, Arizona 85281
480.894.5437 Call us toll-free 1.800.685.2783
Page 5
SpectraPure
®
PREPARATION
1. CHOOSING THE BEST MOUNTING LOCATION:
LIGHT SOURCE: Algae is more likely to thrive inside clear housings when exposed to ultraviolet light and other
sources like metal halide lighting. Avoid installing the unit in bright light or direct sunlight.
EXTREME TEMPERATURES: The unit MUST be kept out of areas that are subject to extreme temperatures like
freezing or temperatures greater than 113° F (45° C).
DI WATER RESERVOIR: Mount system in an area that will have enough room for a reservoir of sufficient size. This DI
Water Reservoir is to be used for the Flush Cycle. (Reservoir needs to hold at least 10 gallons.)
ELEVATION FOR SYSTEM: When mounting your UHE, make sure it is elevated above your fresh water reservoir:
2. TOOLS RECOMMENDED FOR INSTALLATION:
- Adjustable Wrench - Phillips Screw Driver
- Sharp X-Acto Knife - Trash Barrel or Reservoir
- Open End Wrench(s) - Optional Ball Valve or Float Valve (as shown above)
- Electric Drill - Optional Delivery Pump (as shown above)
- 5/8" Drill bit
- 13/16" Drill bit
3. INTRODUCTION TO PUSH FITTINGS:
Push fittings are similar to a Chinese finger trap toy.
In order to release its grip from tubing:
A. Firmly depress and hold the push fitting collar down with your thumbnail.
B. While the push fitting collar is depressed, pull the tubing straight out of
the push fitting.
C. Once the tubing is removed, release the collar.
USE DELIVERY PUMP TO DELIVER WATER WHERE NEEDED
FOR SALT MIXING OR TO SUMP
SpectraPure®Inc.
2167 East Fifth St, Tempe, Arizona 85281
480.894.5437 Call us toll-free 1.800.685.2783
5
Page 6
SpectraPure
®
NOTE: When mounting your UHE, be sure it is elevated above the fresh
water reservoir.
MaxCap
DI #1
SilicaBuster
DI #2
6
UPFLOWUPFLOW
SpectraPure®Inc.
2167 East Fifth St, Tempe, Arizona 85281
480.894.5437 Call us toll-free 1.800.685.2783
Page 7
SpectraPure
®
SETUP PROCEDURES
STEP 1: Connect the 1/2" Black Line to a cold water line that will provide unrestricted water flow
to the RO/DI system.
STEP 2: PURE WATER FLUSH CYCLE INSTALLATION USING THE HIGH AND LOW FLOAT SWITCHES.
A. Install both the High and Low Floats onto an open container.The floats can be mounted
by drilling a 5/8" hole. (The High Float shuts down the system, while the Low Float
turns the system on).
B. Connect the floats to the “Y” adapter.
C. Attach the 3-pin connector on the float switches to the UHE CONTROL MODULE.
NOTE: Floats are to be mounted horizontal when dry and float up when wet. In most
instances we recommend locating the low float approximately halfway down your
reservoir. DO NOT OVERTIGHTEN when installing the floats.
NOTE: Floats must be installed in a DI WATER storage container. This system MUST
be connected to the floats to operate the Flush Cycle. Failure to install the pure
water flush connection for this unit will void any warranty.
STEP 3: For now, direct both the 3/8" blue (product) line and the 3/8" yellow (waste) line to drain.
STEP 4: Open the cold water (tap water) feed that is connected to the black line. Plug in the 115/230
VAC power cord to the AC power source.
STEP 5: At this stage, the system will start producing water from the 3/8" blue and 3/8" yellow lines.
Discard that water for approx. 15 -20 min.
(continued on next page)
SpectraPure®Inc.
2167 East Fifth St, Tempe, Arizona 85281
480.894.5437 Call us toll-free 1.800.685.2783
7
Page 8
SpectraPure
®
SETUP PROCEDURES (continued)
STEP 6: PRESSURE ADJUSTMENT USING THE PRESSURE REGULATOR:
PRESSURE
REGULATOR
A. When pushed down, the Pressure Regulator is in the lock position. Pull up on the knob
to release the lock.
B. While the system is producing water, turn the Pressure Regulator clockwise to increase
pressure or counterclockwise to decrease pressure. Set the pressure to 100 PSI, then
relock the pressure knob.
STEP 7: ADJUSTING THE CONCENTRATE TO PURIFIED WATER RATIO:
If not enough concentrate is allowed to leave the system during operation, impurities will
precipitate out on the membrane surface, clogging the RO Membrane. To prevent this
from happening, the Concentrate to Purified Water Ratio must be checked and adjusted in
order to compensate for pressure and temperature variations that exist in all water supplies.
NOTE: This adjustment must be made at the highest feed water temperature the
system will use. The flow rate of the concentrate should be at least equal to
the product flow rate (1:1)
A. Hold both 3/8" blue and 3/8" yellow lines side-by-side and observe the flow rates.
B. Use a measuring cup and a stop watch to measure the waste and product water. Be
sure you have equal measurements and adjust accordingly.
This procedure will assure you of maximum life and reliability of your SpectraPure System.
Failure to perform this procedure can permanently damage the membrane and will void
the prorated Membrane Warranty.
STEP 8. After you adjust the flow rate, follow STEP 7 again, if needed, to assure that the system is
operating at 100 PSI.
STEP 9. At least 2 gallons (7.57 liters) of purified water will be discarded during this procedure
before you can collect purified water for use. Upon startup, air may be trappped in the DI
cartridges (housing may not appear full). This is a normal condition and it will not affect the
operation of the DI system.
8
SpectraPure®Inc.
2167 East Fifth St, Tempe, Arizona 85281
480.894.5437 Call us toll-free 1.800.685.2783
Page 9
SpectraPure
®
STEP 10. CONNECT BULKHEAD FITTINGS:
Bulkhead Fittings MUST be installed on the same container that the floats are on, SEE
DIAGRAM ON PAGE 7.
3/8" BULKHEAD FITTING: Use a paddle bit and carefully drill a 13/16" hole for installation
at the top of the reservoir (above the high level float).
1/2" BULKHEAD FITTING: Use a paddle bit and carefully drill a hole for installlation at a
point below the high float.
STEP 11. FINAL CONNECTION:
Direct the waste line (yellow) to a drain.
NOTE: Look for leaks and do not leave the system unattended until you are sure
there are no leaks. Monitor the system for 72 hours.
CHECKLIST BEFORE LEAVING SYSTEM UNATTENDED:
• Ensure that all fittings are tight and leak-free before leaving the system unattended.
• The concentrate line (yellow) includes a smaller capillary tube (flow restrictor) that is
located “inside” the tubing. Do not remove or discard this restrictor. The system will
not produce permeate water without the flow restrictor.
• The following conditions must be met before water will flow throught the system:
The system must be powered up, the water source must be turned “ON” and the
water level in the reservoir tank must be below the low level float.
SpectraPure®Inc.
2167 East Fifth St, Tempe, Arizona 85281
480.894.5437 Call us toll-free 1.800.685.2783
9
Page 10
SpectraPure
®
MAINTENANCE PROCEDURES
We recommend that you keep replacement cartridges on hand, ready to install as soon as the
monitor indicates that the cartridge in use is exhausted.
SHELF LIFE FOR FILTERS:
PREFILTERS (Sediment and Carbon Block Filters): Prefilters have an infinite shelf life.
REVERSE OSMOSIS MEMBRANE (RO): Purchase an RO membrane when needed. If you would
like to keep one on hand, you can store it in the refrigerator for up to 1 year. (Keep in its sealed,
original packaging). You should always see moisture inside the bag. If the membrane dries out,
it will not produce water and any warranty will be voided).
DEIONIZING CARTRIDGES (DI): Replacement DI cartridges are shipped in a Mylar® Bag. Keep
them in their sealed, original packaging until use. You can store them for up to 1 year.
SEDIMENT PREFILTER REPLACEMENT:
For maximum contaminant removal and long membrane life, the sediment prefilter must be changed
when the system fails to maintain a minimum inlet pressure of 30 PSI when the system is running.
If your water contains a great deal of sediment, the prefilter may require more frequent changes to
maintain adequate production rate and extended membrane life.
Materials Required: 0.2 micron ZetaZorb
®
NOTE: Failure to use a ZetaZorb
sediment filter as the replacement will void the system’s warranty.
®
Sediment Filter (SF-ZZ-0.2-20), Filter Wrench.
Procedure: (FIRST FILTER ON LEFT)
1. Turn off water supply to the system.
2. Using the provided filter wrench, remove the first housing on the left. Unscrew it
counterclockwise as viewed from the bottom.
3. Remove the old filter and discard.
4. Thoroughly wash the housing with a mixture of hot soapy water and a few teaspoons
of household bleach. Rinse well with clean hot water.
5. Install the new prefilter into the housing, Screw the housing back onto the assembly,
and hand tighten only.
10
NOTE: Do not use filter wrench to tighten housings. Over-tightening will damage
housings and void your warranty.
6. Proceed with carbon block filter replacement.
SpectraPure®Inc.
2167 East Fifth St, Tempe, Arizona 85281
480.894.5437 Call us toll-free 1.800.685.2783
Page 11
SpectraPure
®
CARBON BLOCK PREFILTER REPLACEMENT:
For maximum contaminant removal and long membrane life, periodically test for the presence of
chlorine in the waste water stream. The Carbon prefilter must be changed when more than 0.1 ppm
of chlorine is detected.
Materials Required: 0.5 micron Carbon Block Filter (CF- 0.5 -20), Filter Wrench, Chlorine Test
Kit (TK- CL-10-KIT)
Procedure: (SECOND FILTER ON LEFT WHEN FACING SYSTEM)
1. Perform steps 1-5 on page 10.
2. Turn on system’s water supply and check for leaks.
REVERSE OSMOSIS MEMBRANE REJECTION DIAGNOSTICS:
Although RO membranes are capable of maintaining high water quality over extended
periods of time, eventually they will begin to deteriorate. Normally, the conductivity of
the permeate water will increase as the membrane ages. By comparing the difference
in readings between the Tap water conductivity and the RO water conductivity, the
percentage of rejection of the RO membrane may be calculated and the resultant value may then
be used to determine the condition of the membrane. In this way, the operator will know when
the membrane needs to be replaced. Membrane failure will be indicated by a reduction in the
percentage rejection which will be determined by calculating the differential between the input
and output readings.
In order to accurately determine the condition of the RO Membrane, a conductivity meter capable
of reading the tap water conductivity and the permeate water conductivity should be used. Using
this meter, you will be able to easily determine the RO membrane’s condition.
Before performing the diagnostic test on the RO membrane, make sure that the RO system has been
“ON” and producing pure water for a minimum of 10 minutes. Also check the brine (yellow) line to
make sure that water is flowing and that the flow ratio between the brine water and the permeate
water is at a ratio that is approximately 1:1. (NOTE: The pressure gauge should indicate a pressure
reading of 100 PSI during this 15-20 minute test period.)
Procedure:
1. Read the Tap Water conductivity and record the reading. ___________
2. Read the Permeate Water conductivity and record the reading. ___________
3. Use the two reading to apply them to the calculation below:
4. The general rule is that you should replace your Reverse Osmosis (RO) Membrane when
the % of rejection falls below 96%.
(X - Y) = Z
X
EXAMPLE: (500 - 20) = 480 / 500 = 0.96 (96% rejection)
SpectraPure®Inc.
2167 East Fifth St, Tempe, Arizona 85281
% REJECTION
=
BY MEMBRANE
480.894.5437 Call us toll-free 1.800.685.2783
TAP WATER TDS = X
RO WATER TDS = Y
11
Page 12
SpectraPure
®
REVERSE OSMOSIS MEMBRANE PERFORMANCE TESTING:
The actual performance of the membrane in the MC-RODI-400UHE-20 is primarily dependent on Tap Water Temperature.
In order to characterize a membrane, there must be common testing data. For testing the UHE-400 membrane, the
specification is 77° F water temperature. Warmer water will result in an increase in production and colder water will
result in a decrease in production. Most locations will not have exactly 77° F water. Use the calculation below to determine
what the membrane will produce with your water conditions. Look up the water temperature on the chart below to
determine the Temperature Correction Factor (TCF).
Temperature Correction Factor Table (TCF)
°F /°C TCF °F /°C TCF °F /°C TCF
41.0 /5 0.521 59.0 /15 0.730 77.0 /25 1.000
42.8 /6 0.540 60.8 /16 0.754 78.8 /26 1.031
44.6 /7 0.560 62.6 /17 0.779 80.6 /27 1.063
46.4 /8 0.578 64.4 /18 0.804 82.4 /28 1.094
48.2 /9 0.598 66.2 /19 0.830 84.2 /29 1.127
50.0 /10 0.620 68.0 /20 0.857 86.0 /30 1.161
51.8 /11 0.640 69.8 /21 0.884 87.8 /31 1.196
53.6 /12 0.661 71.6 /22 0.912 89.6 /32 1.232
55.4 /13 0.684 73.4 /23 0.941 91.4 /33 1.267
57.2/14 0.707 75.2 /24 0.970 93.2 /34 1.304
TEMPERATURE COMPENSATION
400 x T.C.F. =
Nominal
Production
Rate
Actual
Production
Rate
REVERSE OSMOSIS MEMBRANE REPLACEMENT:
1. Turn off the water supply to the RO system and unplug the power cord. Place the system where the membrane
housing is easily accessible.
2. Loosen the single brass compression nut and remove the black tubing from the membrane housing feed
water fitting. This is the “input” end.
3. Loosen the brass compression nut and remove the black tubing from the opposite end of the membrane
housing.
4. Remove the blue tube from the center-located push fitting on the same end.
5. Use two flat head screwdrivers to weparate and release the “tooth-like” clips on each end of the membrane
housing. Remove the housing from the two clips.
6. The membrane housing may now be relocated to a sink or other waterproof area.
7. Remove the two bolts that hold the yoke clamp together on the end of the housing with one fitting. This is
the “input” end.
8. Pull or pry the black cap from the steel housing. Pull the membrane out of the housing. Note the orientation
of the membrane. The brine seal is on the end to first come out.
9. Wash the empty housing with soapy water. Rinse thoroughly with hot, clean water.
10. Put a small amount of silicone lubricant on both ends of the protruding product tube.
11. Insert the new membrane into the housing with the brine seal end the last to go in. Firmly push the membrane
into the housing until it bottoms out.
12. Carefully press the black cap back onto the base.
13. Reinstall the yoke clamp and tighten both bolts.
12
(continued on page 14)
SpectraPure®Inc.
2167 East Fifth St, Tempe, Arizona 85281
480.894.5437 Call us toll-free 1.800.685.2783
Page 13
SpectraPure
®
Membrane Clip
Yoke Clamp
Concentrate Recirculation Line
Blue Product Water Tubing
in Push Fitting
3/8" Yellow Drain Line
3/8" Concentrate to Drain,
3 PSI Check Valve
AC Power Cord
Low-Pressure Cutoff Switch
Final Product Water Output
Input Pressure GaugeSystem Pressure Gauge
Membrane Feed Line
1/2" Blue Flush Line
Feed Water Input
Yoke Clamp
Membrane Clip
SpectraPure®Inc.
2167 East Fifth St, Tempe, Arizona 85281
480.894.5437 Call us toll-free 1.800.685.2783
13
Page 14
SpectraPure
®
REVERSE OSMOSIS MEMBRANE REPLACEMENT: (continued)
14. Reinstall the membrane housing assembly into the two “tooth-like” clips and squeeze the clips together until
the membrane is snug.
15. Reconnect the black tubing on the input end and tighten the compression nut.
16. Reconnect the black tubing on the opposite end and tighten the compression nut.
17. Inset the blue tubing firmly into the push fitting on the same end.
18. Turn on the water supply to the system and plug in the power cord.
19. The water level will have to be below the low float for the system to turn on so you can check for leaks.
TIPS FOR LONG MEMBRANE LIFE:
1. Replace the 0.2micron sediment filter at least once every 6 months. This will prevent membrane fouling due
to silt or sediment depositing on the membrane.
2. Replace the 0.5 micron carbon block filter at least once every 6 months or when chlorine breakthrough
occurs. This will ensure good membrane life and protect the membrane from chlorine damage.
3. The membrane should not be operated at lower than the recommended concentrate to purified water ratios.
4. Operating reverse osmosis systems on softened feed water greatly reduces the chances of membrane fouling.
DEIONIZATION CARTRIDGE MAINTENANCE AND REPLACEMENT:
Materials required: Filter wrench and DI cartridge.
Procedure:
1. When the reading on the external Resistivity Monitor drops below 1 Mohm/cm2 (or whatever the minimum
requirement is), it is time to replace both DI cartridges.
2. Disconnect power to the system and shut down the water supply line.
3. Use the filter housing wrench to rotate the housing counterclockwise and remove.
4. Remove the spent DI cartridge from the housing and discard.
5. Install a new DI cartridge in the housing.
6. Be sure the DI cartridge is installed in the same orientation as the original and that the top seal is securely
attached to the top of the cartridge.
7. Reinstall and tighten the cartridge housing by rotating it clockwise, then hand tighten.
14
8. Turn the sysstem on and check for leaks.
SpectraPure®Inc.
2167 East Fifth St, Tempe, Arizona 85281
480.894.5437 Call us toll-free 1.800.685.2783
Page 15
SpectraPure
®
THREE YEAR MANUFACTURER’S WARRANTY
SpectraPure, Inc.® warrants the product to the original owner only to be free of defects in material and
workmanship for a period of one year from the date of receipt. SpectraPure’s liability under this warranty
shall be limited to repairing or replacing at SpectraPure’s option, without charge, F.O.B. SpectraPure’s factory,
any product of SpectraPure’s manufacture. SpectraPure will not be liable for any cost of removal, installation,
transportation or any other charges which may arise in connection with a warranty claim. Products which are
sold but not manufactured by SpectraPure are subject to the warranty provided by the manufacturer of said
products and not by SpectraPure’s warranty. SpectraPure will not be liable for damage or wear to products
caused by abnormal operating conditions, accident, abuse, misuse, unauthorized alteration or repair or, if the
product was not installed in accordance with SpectraPure’s or other manufacture’s printed installation and
operating conditions, or damage caused by hot water, freezing, flood, fire or acts of God.
SpectraPure will not be responsible for any consequential damages arising from installation or use of the
product, including any water or mold damage due to flooding which may occur due to malfunction or faulty
installation, including, but not limited to failure by installer to over- or under-tighten fittings, housings, and/
or push-style fittings, or improper installation of push-style fittings. Consumable items such as pre filters and
membranes are not covered under the two year warranty.
SpectraPure warrants (prorated) the performance of tested SpectraSelect™ RO membrane elements only, for
one year from date of receipt by the buyer, providing that the loss of performance was not caused by fouling,
neglect, or water conditions exceeding the feed water parameters listed in the applicable product manual
(refer to detailed membrane warranty information). SpectraPure will, on confirmation of loss of performance
during the warranty period, credit the prorated amount of the current catalog price of the element. The
disposable filters and cartridges are not covered under the warranty.
To obtain service under this warranty, the defective system or components must be returned to SpectraPure
with proof of purchase, installation date, failure date and supporting installation data. Any defective product
to be returned to the factory must be sent freight prepaid; documentation supporting the warranty claim
and a Return Merchandise Authorization (RMA) number must be included. SpectraPure will not be liable for
shipping damages due to the improper packaging of the returned equipment and all returned goods must
also have adequate insurance coverage and a tracking number.
SpectraPure will not pay for loss or damage caused directly or indirectly by the presence, growth, proliferation,
spread or any activity of “fungus”, wet or dry rot or bacteria. Such loss or damage is excluded regardless of
any other cause or event that contributes concurrently or in any sequence to the loss. We will not pay for loss
or damage caused by or resulting from continuous or repeated seepage or leakage of water, or the presence
or condensation of humidity, moisture or vapor, that occurs over a period of 14 days or more. “Fungus” and
“fungi” mean any type or form of fungus or Mycota or any by-product or type of infestation produced by such
fungus or Mycota, including but not limited to, mold, mildew, mycotoxins, spores, scents or any biogenic
aerosols.
SpectraPure will not be liable for any incidental or consequential damages, losses or expenses arising from
installation, use, or any other causes. There are no expressed or implied warranties, including merchantability
or fitness for a particular purpose, which extend beyond those warranties described or referred to above.
* The three year limited warranty does not apply to consumable items, including but not limited to,
filters and cartridges unless specifically stated above.
SpectraPure®Inc.
2167 East Fifth St, Tempe, Arizona 85281
480.894.5437 Call us toll-free 1.800.685.2783
15
Page 16
SpectraPure
®
TROUBLE SHOOTING GUIDE
Problem Cause Corrective Action
Low production rate.
a. plugged prefilters. i. Replace prefilters.
b. low water temperature. ii. Use higher GPD membrane.
c. fouled membrane. iii. Replace membrane.
d. plugged flow restrictor. iv. Replace flow restrictor & membrane.
Zero production rate.
a. Dried membrane. i. Replace membrane.
b. Power supply not plugged in ii. Plug power in.
c. Both floats need to be dry iii. Both floats need to be dry and level, not drooping
Extremely high production rate.
a. Ruptured membrane. i. Replace it.
Milky colored water.
a. Air in system. i. Air in the system is a normal occurrence with initial
startup of the RO/DI system. This milky appearance
will disappear during normal use within 1-2 weeks.
The water in the Pure Water container drains out when not used.
a. The system is not elevated higher
than the Pure Water container
Cannot adjust waste water flow
a. W.F. adjustment valve in lock
position
i. Elevate the system higher than the Pure Water
container to avoid siphoning.
i. Unscrew lock nut on W.F. valve
REPLACEMENT AND OPTIONAL PARTS
Part No. Description
SF-ZZ-0.2-ABS-20 0.2 micron ZetaZorb® Sediment Filter (1st Stage)
CF-0.5-20 0.5 micron Carbon Block Prefilter (2nd Stage)
MEM-LAB-0400 Replacement Membrane (3rd Stage)
DI-MC-20 20 in. MaxCap® Deionization Cartridge (4th Stage)
DI-SB-20 20 in. SilicaBuster™ Deionization Cartridge (5th Stage)
V-SOL-4-PL-DEMA 1/4 in. Solenoid Valve
PSP-400UHE-PUMP-230 High-Volume Upgrade Commercial Pump
16
SpectraPure®Inc.
2167 East Fifth St, Tempe, Arizona 85281
480.894.5437 Call us toll-free 1.800.685.2783
Loading...