Spectralink RFP4 1G9 User Manual
KIRK Base Station 1.9 GHz
User s Guide
KIRK_BS_1G9_141432.qxp 03-08-2005 12:35 Side 1
1 Introduction
The base st ation is only intended for use with a wire less server . The base st ation is not intended to be
connected directly to the PSTN network. The base
st ation is designed with two internal antennas and
support s antenna diversity. The base station is also
able to carry out handover between the RF channels
under the same base st ation, and handles four wire less speech channels simult aneously. The base st ati on is able to frame synchronise with other base st ati ons under the same Wireless Server.
T ransmission lenght is up to 1.2 miles on a twisted
p air (in one building), e.g. cat.4, between the base
st ation and wireless server. The base st ation is also
power supplied from this connection (maximum sup ply 1.5 W). The radius of coverage is up to 1960 feet
with a handset in free sight. It is possible to connect
a maximum of 8 base st ations to a wireless server
without an exp ansion board, 16 base st ations with an
expansion board and 32 with a linked solution.
2 Inst allation
First you have to determine where to inst all the base
st ation to have the right coverage. The average
coverage within buildings is 246 feet. The coverage
depends on the construction of the building, archite cture and choice of building material. Y ou may have
to use the base st ation coverage determination kit
(Diagnostic T ooll) to optimize your inst allation. This
Diagnostic Tool, consist s of a base st ation which has
no need for a wireless server . It can easily be
moved around in the building and 1 to 8 handset s
can be connected.
Pull the a/b wire from your inst allation through the
wall suspension and then mount the wall suspension
on the wall.
Connect the a/b wire to the plug at the rear of the
base st ation, using the 2 inner connectors of the
plug.
KIRK_BS_1G9_141432.qxp 03-08-2005 12:35 Side 2
If you need to remove the base st ation please sep a rate it from the wall suspension with a gentle push of
a screwdriver.
Click the base st ation on to the wall suspension.
Af ter the wireless server is powered up again a cable
lenght measurement is needed in order to find the
correct Cable Delay Value (CDV).
NOTE!
Cable dimensions min. as A WG 26.
KIRK_BS_1G9_141432.qxp 03-08-2005 12:35 Side 4
Important Safety Instructions and Product Infor mation
Before using your telephone equipment, you should
always follow basic safety instruction to reduce the
risk of fire, electrical shock and injury to persons,
and damage to property.
1 Read and understand all instructions
2 Follow all warnings and instructions including
those marked on the product
3 Unplug this product before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use damp
cloth for cleaning
4 Do not inst all the telephone equipment in the
bathroom or near a wash bowl, kitchen sink, or
laundry tub, in a wet basement, or near a swim ming pool
5 Slot s or openings in the cabinet back and bot-
tom of the equipment are provided for ventilation
to protect it from over-heating. These openings
must not be blocked or covered.
6 The product should be operated only from the
type of power source indicated on the instructions. If you are not sure of the type of power
supply, consult your dealer or local power com pany.
7 Do not overload wall outlet s and extension cords
as this can result in fire or electrical shock.
8 Never push object s of any kind into this product
through cabinet slot s as they may touch danger ous volt age point s or short out p art s that could
result in fire, electrical shock, or injury . Never
spill liquid of any kind into this product.
9 T o reduce the risk of electrical shock or burns,
do not disassemble this product. Opening or
removing covers may expose you to dangerous
volt ages, dangerous electrical current, or other
risks. Incorrect reassemble can cause electrical
shock when the appliance is subsequently used.
If the product need rep air , consult your dealer .
10 Refer servicing to qualified service personnel
under the following conditions:
KIRK_BS_1G9_141432.qxp 03-08-2005 12:35 Side 6
Loading...