NETLINK 8000 SERIES WIRELESS TELEPHONE
AND ACCESSORIES USER GUIDE
2
NetLink 8020 Wireless Telephone
*
2
ABC
1
4
GHI
7
PQRS
3
DEF
0
FCN
LINE
6
MNO
9
WXYZ
#
5
JKL
8
TUV
NetLink 8020
Volume
up
START
Function key
(FCN)
Microphone
LINE
Keypad
END
Headset
jack
Softkeys
Nav keys
Volume
down
NavOK
3
NetLink 8030 Wireless Telephone
*
2
ABC
1
4
GHI
7
PQRS
3
DEF
0
FCN
LINE
6
MNO
9
WXYZ
#
5
JKL
8
TUV
NetLink 8030
Volume
up
Volume
down
START
Function key
(FCN)
Microphone
LINE
Keypad
END
Headset
jack
Softkeys
Nav keys
TALK
NavOK
4
Notice
SpectraLink Corporation has prepared this document for use by SpectraLink personnel
and clients. The drawings and specifications contained herein are the property of SpectraLink and shall be neither reproduced in whole or in part without the prior written
approval of SpectraLink, nor be implied to grant any license to make, use, or sell equipment manufactured in accordance herewith.
SpectraLink reserves the right to make changes in specifications and other information
contained in this document without prior notice, and the reader should in all cases consult
SpectraLink to determine whether any such changes have been made.
The terms and conditions governing the sale of SpectraLink hardware products and the
licensing of SpectraLink software consist solely of those set forth in the written contracts
between SpectraLink and its customers. No representation or other affirmation of fact
contained in this document including but not limited to statements regarding capacity,
response-time performance, suitability for use, or performance of products described
herein shall be deemed to be a warranty by SpectraLink for any purpose, or give rise to any
liability of SpectraLink whatsoever.
In no event shall SpectraLink be liable for any incidental, indirect, special, or consequential
damages whatsoever (including but not limited to lost profits) arising out of or related to
this document, or the information contained in it, even if SpectraLink has been advised,
knew, or should have known of the possibility of such damages.
Registered Model Numbers
This document covers registered handset model: 802X/803X
Registered charger models: PCS1850, PCD1850, PCQ1850
Registered Battery Pack models: PBP0850, PBP1300, PBP1850
For regulatory information, please see Regulatory Information (72-1405-00).
Please email questions or comments about this document to feedback@spectralink.com
5
INTRODUCTION
Your NetLink 8000 Series Wireless Telephone uses radio wave
technology to send and receive voice transmissions. It is designed
to operate like a cell phone. However, the handset uses the private
telephone system installed in your facility and will not operate outside the area covered by this system.
About This Guide
This guide is meant to provide general information about your
handset. Contact your system administrator for additional information on how your handset functions within your telephone system.
This guide includes information about:
• The Handset
• Getting Started
• Advanced Features
• Handset Accessories
• Handset Administration
6
TABLE OF CONTENTS
THE HANDSET ...................................................................... 8
Modes of Operation ................................................................8
Menu Navigation ....................................................................8
Handset Displays ....................................................................9
Status Bar Indicators ......................................................... 10
Softkey Labels ...................................................................... 12
GETTING STARTED ............................................................. 14
Basic Handset Operation Summary ............................... 14
ADVANCED FEATURES ....................................................... 19
Facility-Specific Features .................................................... 19
Speakerphone ...................................................................... 19
Predial ................................................................................... 19
Redial .................................................................................... 19
Data Entry and Editing ........................................................ 20
Phonebook ............................................................................ 21
Phonebook List Options ................................................. 21
Phonebook Edit Entry Options ...................................... 22
Speed-Dial ........................................................................... 22
The Config Menu .................................................................. 23
Config Menu Options ........................................................... 24
Toggle Options .................................................................. 26
Profiles ............................................................................... 26
Changing Ring Settings ................................................... 26
Default Profile Settings ................................................... 27
Push-to-talk (PTT) ................................................................. 28
7
CHARGERS, BATTERY PACKS AND ACCESSORIES ...............30
Battery Packs .......................................................................30
Charger Models ....................................................................31
Charging Status ................................................................32
Single Charger ......................................................................33
Dual Charger .........................................................................34
Quad Charger ........................................................................35
Carrying Options ...................................................................36
Headsets ...............................................................................36
HANDSET ADMINISTRATION ...............................................37
FAQs .......................................................................................37
Specifications ......................................................................39
CARE OF YOUR HANDSET ....................................................47
8
The Handset
THE HANDSET
Modes of Operation
Your handset has five modes of operation:
Menu Navigation
The navigation keys (Nav keys) just below the softkeys are used to
navigate through menu options. These are referred to in this guide
as
NavS, NavT, NavW, NavX, and NavOK.
Mode Description
Standby The handset is on-hook and idle.
Active The handset is in a call, a call is coming in,
or a call is being dialed.
Config menu User preferences are being accessed in the
Config Menu. In this mode the handset is
on, but will not receive calls.
Message alert Custom text messaging applications may
be programmed for your facility. This
mode is activated through the
FCN menu.
Push-to-talk (PTT) The SpectraLink 8030 Wireless Telephone
uses channels for incoming and outgoing
radio communication. While PTT is active,
the handset is in PTT mode.
Nav
Nav
Nav
Nav
NavO
K
9
The Handset
Shortcut Keys
When a menu is displayed, a shortcut key may be displayed on the
right edge of the menu line. Press the corresponding number on
the keypad to activate the corresponding menu option.
Handset Displays
The top row of the display provides status indicators for various
handset conditions. It is referred to as the status bar.
The middle lines display information about the handset identity,
user profile, calls in progress, menu options, and data from telephone system.
The bottom row displays softkey labels.
Standby Mode Display
Press NavW or X to display the second set of available softkeys:
When the handset is in a call or in active mode, information from
the telephone system in your facility displays. Information may
include extension or telephone number of called or calling party,
active line information, and softkeys that have been programmed
by your system administrator. Press
FCN to scroll to additional soft-
key sets.
Ext. 555
John Doe
07-05 12:19p
Profile: Loud
1: General
Spkr Phbk Prof Lock
Extension
User
profile
Default PTT
channel
(model 8030
only)
Softkey
labels
User name
Date/time
Spdl Redl Cfg
10
The Handset
Status Bar Indicators
Indicator Function
The signal-strength icon indicates the
strength of the signal and can assist the
user in determining if the handset is
moving out of range.
The voicemail icon is activated when a
new voicemail message is received when
this feature is available in your facility.
The battery icon indicates the amount of
charge remaining in the Battery Pack.
When only one level remains, the Battery
Pack needs to be charged.
The speakerphone icon displays when
the speakerphone is active.
The line indicators are associated with
telephone line status and access.
Up and down arrows are displayed when
the menu has additional options above or
below.
Left or right arrows are displayed during
editing when the cursor may be moved
left or right.
Telephone ring icon. A regular telephone
call is coming in.
Messaging ring icon. A call is coming in
from a Messaging application.
The PTT ring con. A PTT call is coming
in.
1
11
The Handset
The priority PTT ring icon. A call is
coming in on the priority PTT channel.
This call will override any other.
Muted The muted indicator displays after the
Mute softkey has been pressed. It
indicates that the microphone is not
transmitting sound. Press the
Mute
softkey again to unmute the microphone.
Locked Locked indicates that the keypad is
locked to prevent accidental activation.
Use the
Unlk softkey plus the # key to
unlock it.
[No Service message]
If warning tones are enabled, an alarm will
sound and a descriptive message displays
when the handset cannot receive or place
calls. You may be outside of the covered
area. Walk back into the covered area. The
in-service tone indicates service is reestablished.
The download icon indicates that the
handset is downloading code. This icon
only appears while the handset is running
the over-the-air downloader. It appears to
the right of the signal strength icon in the
same location as the voicemail icon.
Indicator Function
12
The Handset
Softkey Labels
The bottom row of the handset displays labels associated with the
four softkeys just below it. When a softkey is active, a label appears
to describe its function. Pressing the softkey will activate the feature. When additional softkeys are available,
Nav arrows appear to
the left and right of the softkey labels. Press
NavX or W to view
the additional softkey labels.
These are some of the softkeys you will see.
Label Description Action
Back Go back Returns to the previous menu
display.
CAPS
caps
Change case Toggles to allow a change in case
when entering alphabetical text.
Cfg Configure Opens the
Config Menu.
Clr Clear Deletes the entry.
Cncl Cancel Returns to the previous menu
display without saving any data that
might have been entered.
Del Delete Deletes the character to the left of
the cursor.
Done Finished Exits a list when more than one
selection is possible.
Edit Edit Opens an editing window so you
can change information about an
entry in the phonebook.
Exit Exit Exits out of the menus.
Lock Lock Keys Locks the keypad to prevent
accidental activation. See Unlk
softkey below.
Hold Hold Places a call on hold.
13
The Handset
Mute Mute Toggles to mute or unmute the
microphone.
No Negative reply Press to reply “No” to a displayed
question.
Phbk Phonebook Opens the phonebook.
Play Play Plays the selected ring tone.
Prof Profile Opens the Profile menu.
Redl Redial Displays a list of the last 10
numbers dialed.
Save Save Saves the current entry to the
phonebook.
Set Set From the speed-dial assignment
display, opens the phonebook
listing for assigning a phonebook
entry to a speed-dial key.
Spdl Speed-dial Opens the list of speed-dial
numbers.
Spkr Speakerphone Toggles speakerphone function.
Unlk Unlock keys Press
Unlk, then the # key to
unlock a locked keypad.
USB Active USB port Displays when the handset is being
configured via the USB port of the
Dual Charger.
View View Displays information about an
entry in the phonebook .
Yes Positive reply Press to reply “Yes” to a displayed
question.
Label Description Action
14
Getting Started
GETTING STARTED
Your NetLink 8000 Series Wireless Telephone is designed for full
mobility within the workplace and operates much like a cell phone.
It also interfaces with the telephone system at your workplace and
incorporates advanced telephony features. This section covers the
basic functions available in every facility. For specific telephony system functions, see the
Facility-Specific Features
section or contact your
system administrator.
Basic Handset Operation Summary
Place the handset into the charger for a minimum of
two hours. The handset's Battery Pack must be fully
charged before its first use. See the section Charger
Models for full information.
If you want to Then
Remove the
Battery Pack
Press down on the latch on the Battery
Pack at the back of the handset and pull
the Battery Pack towards you. The
Battery Pack releases outward.
Replace the
Battery pack
Slide the lip of the Battery Pack into the
bottom of the cavity. Push the top of the
Battery Pack until it snaps into place. You
should not have to force it into the
handset.
Turn handset on Press and hold the
END key until two
chirps sound.
Turn handset off Press and hold the
END key. One chirp
will sound. If you are in a call, hang up
first, then turn off the handset.
15
Getting Started
Unlock the keypad Press the Unlk softkey, then #, to unlock
the keypad.
Lock the keypad Press the
Lock softkey.
Make an internal call Press the
START key, wait for a dial tone,
then dial the extension.
Make an external call Press the
START key, wait for a dial tone,
then dial the number just as you would
from your desk phone.
Make an emergency
call
Open the speed-dial list to determine if
you have an emergency speed-dial number
that has been programmed by your system
administrator. If so, it will appear as the
first item on the speed-dial list with a >
in front of it and the programmed
keypress as the next character. Press the
programmed key for 3 seconds to activate
the call. See
Open the speed-dial list
below.
Select a line If multiple lines are available, your
telephone system may require you to
select a line before dialing a number.
Press
LINE and the number key
corresponding to the desired line. You
will hear a dial tone.
Dial a number Once you hear a dial tone, press the
number keys to dial the number.
Predial a number From standby mode, press the keypad to
enter up to 20 numbers. Then dial the call
by pressing
START, NavOK or the Spkr
softkey.
If you want to Then
16
Getting Started
Redial a number Press the Redl softkey from standby
mode. A list of recently-dialed numbers
displays. Select the number and press
START, NavOK or the Spkr softkey.
Make a
speed-dial call
Press and hold the speed-dial key
assigned to the number.
Open the
speed-dial list
Press the
Spdl softkey from standby
mode.
Make a
phonebook call
Press the
Phbk softkey from standby
mode. Highlight the name and press the
START softkey.
Answer a call The handset will ring or vibrate to alert
you of an incoming call. Additionally, a
line indicator on the display may flash
and the display may show information
about the call, such as the caller’s name
and extension.
To answer a call, press the
START key and
hold the earpiece to your ear. You may
also activate the speakerphone function
or use a headset.
Answer a call on a
second line
If you are on a call and hear subdued
ringing, a call is coming in on a second
line. The line number on the display may
be flashing. To answer this call, put your
first call on hold and press the
LINE key,
then the line number of the second call.
Answer with headset Press any key (other than
END, a Nav key,
or a softkey) to answer a call when a
headset is plugged in.
If you want to Then
17
Getting Started
Silence while ringing Press the END key to silence the ring.
Change the
ring volume
Press the up/down volume buttons on
the side of the handset during ringing.
The default ring volumes are set in the
User Profile menus.
Activate or deactivate
the speakerphone
Press the
Spkr softkey and speak towards
the handset. Note that this feature may
be unavailable in your facility.
Adjust the
speaker volume
Press the up/down volume buttons on
the side of the handset during the call.
Adjust the
headset volume
Press the up/down volume buttons on
the side of the handset during the call.
Place a call on hold Press the
Hold softkey.
Resume a held call Press the
LINE key followed by the line
number key.
Mute the microphone Press the
Mute softkey.
End the call Press the
END key. Be sure to do this at
the end of each call to return to the
standby mode.
Change the profile Press the
Prof softkey and use the Nav
keys to select a new profile while in
standby mode. The selected profile is
marked with an asterisk (*).
Edit the phonebook Press the
Phbk softkey from standby
mode.
If you want to Then
18
Getting Started
Display additional
features
During a call press the FCN key to display
the softkeys programmed to additional
features available in your facility. These
might include transfer, conference,
voicemail, etc.
Turn on the backlight The backlight comes on when any key is
pressed or when there is an incoming call
and stays on for 10 seconds. It turns off
after 10 seconds if another key is not
pressed within that period.
If you want to Then
19
Advanced Features
ADVANCED FEATURES
Facility-Specific Features
Press the FCN key while off-hook or in a call to display the the softkeys programmed for advanced telephony features such as transfer,
conference, and voicemail. The features may be activated by pressing the corresponding shortcut key. Contact your system administrator for more information about custom features available in your
facility.
Speakerphone
Your system administrator can enable or disable the speakerphone
mode. If the speakerphone is enabled, it is activated by pressing the
Spkr
softkey. Press the
Spkr
softkey again to end speakerphone
mode. The audio then transfers to the handset earpiece. When speakerphone mode is disabled,
Spkr
will not appear as a softkey label.
Predial
Predial is automatically activated when you begin pressing numbers
on the keypad while in standby mode. Up to 20 numbers may be
pressed. The call is then placed by pressing the
START key, NavOK,
or the
Spkr softkey. Press Save to add the dialed number to the
phonebook before placing the call.
Predial may be disabled in the
Config Menu.
Redial
The Redl softkey is available in the standby mode. When it is
pressed, a list of the last 10 outgoing calls will be displayed. Use
the
Nav keys to highlight the number and press START to dial the
number.
You may save any of these numbers to the phonebook by pressing
the
Save softkey. You may also view any entry already saved in the
phonebook by pressing the
View softkey.
20
Advanced Features
Data Entry and Editing
Enter numbers by pressing the buttons on the keypad. The blinking underscore identifies the current cursor position. When entering alphanumeric strings, the
CAPS/caps softkey will appear and
may be pressed to toggle the case. Enter letters by repeatedly pressing the corresponding key until the desired letter displays on the
screen. Use the
CAPS softkey to change the case as needed.
To edit during entry, delete the character to the left of the cursor by
pressing the
Del softkey. To replace an entry, delete it by pressing
the
Clr softkey and then enter the new data. To edit an existing
entry, use
NavW and NavX to move the cursor position, and then
press the
Del softkey to delete the character to the left. Insert new
data by pressing the buttons on the keypad.
Alphanumeric entries:
Key caps CAPS
1 11
2 2 a b c 2 A B C
3 3 d e f 3 D E F
4 4 g h i 4 G H I
5 5 j k l 5 J K L
6 6 m n o 6 M N O
7 7 p q r s 7 P Q R S
8 8 t u v 8 T U V
9 9 w x y z 9 W X Y Z
0 00
* * . - ! $ % & ’ ( ) + , : ; / \ = @ ~
# # <space>
21
Advanced Features
Phonebook
The phonebook in your NetLink 8000 Series Wireless Telephone
can store up to 20 user-defined numbers. Open the phonebook list
by pressing the
Phbk softkey from the standby mode or by pressing
the
Save softkey during predial. You may add, delete, or edit a
phonebook entry, open the speed-dial list or start a call from the
phonebook.
The phonebook list is sorted alphabetically. If the system speeddial key has been programmed, it will be listed as the first entry
with a greater-than symbol (>) as the first character. Only the system administrator may change this entry. The
<new> option
appears until the maximum number of entries has been entered.
Phonebook List Options
If you want to Then
Dial number Press
START or the Spkr softkey.
Search for an entry Press the key corresponding to the first
letter of the name. Use
NavW and NavX
to edit the search characters.
View an entry Press
NavOK.
Enter a new name and
number
Select the
<new> option (if available) and
press the
Edit softkey to open the enter
number display.
Delete an entry Press the
Del softkey to delete an entry.
Edit an entry
Press the
Edit
softkey to open the enter
number display and edit the existing
number. Use the
Nav
keys to highlight and
select an entry. Press the
Dial
softkey to
dial the number.
22
Advanced Features
Phonebook Edit Entry Options
Speed-Dial
The NetLink 8000 Series Wireless Telephone can assign up to 10
speed-dial keys to numbers entered into the phonebook.
Open the speed-dial list by pressing the
Spdl softkey from standby
mode. If programmed, the first item on this list is the system-wide
speed-dial number set by the system administrator. It is specially
marked with a greater-than symbol (>) on the left side of the row.
It is usually reserved for emergency situations.
To make a speed-dial call, press and hold the corresponding key for
one second. The system speed-dial key must be pressed for three
seconds. The handset will display the name and number for one
second before the call is dialed. You may press
END during this sec-
ond to terminate the call.
You may also use the
Nav keys to highlight a number or listing and
then press
START or the Spkr softkey to dial the number. The Exit
softkey returns you to the standby mode.
A phonebook entry may be assigned to a speed-dial key from the
speed-dial list. Select the speed-dial key that you wish to assign and
If you want to Then
Dial number Press
START or the Spkr softkey.
Assign a speed-dial
number to this entry
Press the
Spdl softkey. Use the Nav keys
to highlight an empty slot and then press
NavOK.
Edit an entry Press the
Edit softkey to open the enter
number display and edit the existing
number.
Return to
phonebook list
Press the
Back softkey or NavOK.
23
Advanced Features
then press the Set softkey to open the phonebook list. Use the
search routine or the
Nav keys to select the desired entry.
Press
NavOK to assign the selected name to that speed-dial key. The
Back softkey returns you to the speed-dial list. Speed-dial entries
may be edited through the phonebook, as described above.
The Config Menu
When the handset is in standby mode, press the
Cfg
softkey to enter
the
Config Menu
. The handset cannot make or receive calls while in
the
Config Menu
. This menu allows you to set user preferences.
Refer to the diagrams on pages 24-25.
Scroll through menu options by using
NavS
and
NavT
. When an
asterisk (*) appears to the left of an option, it indicates that the
option is currently selected. Press the
Exit
softkey to return to
standby mode. Use the
Back
softkey to return to the previous menu.
Speed Dial Key 3
Choose a Number
>[System Name]
[Name]
[Name]
[Name]
Back
Config Menu
General Settings
Lock Keys
User Profiles
Phone Settings
Push-to-talk
Prof Pl Exit
3
Menu line
Shortcut
key
Info line
24
Advanced Features
Config Menu Options
Lock Keys
User Profiles
Silent
Vibrate
Loud
Soft
Custom
Set as Active
Ring Settings
Noise Mode
Ring in Headset
Ring in Speaker
Warning Tones
Key Tones
Push-to-talk
Ring Cadence
Ring Tone
Ring Volume
Vibrate Cadence
Ring Delay
continued on next page
Telephone
Message Alert 1
Message Alert 2
25
Advanced Features
continued from previous page
Phone IP Address
SVP IP Address
Firmware Version
System Info
Push-to-talk
Default Channel
Subscribed Channels
PTT Audio Volume
PTT Tone Volume
Phone Settings
Extension Info
Keypad Autolock
Display Contrast
Use Hearing Aid
Use No Hearing Aid
Startup Song
Play/Inhibit
Predial
Enable/Disable
Extension Number
Extension Name
26
Advanced Features
Toggle Options
Some menu options that have only two possibilities operate on a
toggle basis. The current setting is shown on the second row of the
display, called the info line. Highlight the option and press
NavOK
to toggle between the settings. For example, when
Ring in Headset
is the menu option,
Ring in Speaker will show on the info line. If
you select
Ring in Headset, Ring in Headset will show on the info
line and the menu option will toggle to
Ring in Speaker.
Profiles
Your handset ring behavior is established by five User Profiles:
Silent, Vibrate, Loud, Soft, and Custom. The currently-active user
profile is shown on the standby display. The ring behavior can easily be changed by pressing the
Prof softkey and selecting a new pro-
file from the list when the handset is in standby mode. The
currently-active profile is marked with an asterisk (*).
Changing Ring Settings
To change the ring tone or any other ring setting for any profile, go
to
User Profiles and select the profile. Select Ring Settings and then
select
Telephone for standard phone calls or one of the Message
Alerts
for text messages. Then select the ring option you want to
adjust. See page 24 for the diagram that shows this sequence
graphically.
User Profiles
Choose a Profile
Silent
Vibrate
Loud
Soft
Prof P Back
3
*
27
Advanced Features
Default Profile Settings
Contact your system administrator if you want to reset all user profiles back to these default settings.
Setting/Profile Silent Vibrate Soft Loud Custom
Ring Cadence Off Off Telephone Telephone Telephone
Ring ToneTone 1Tone 1Tone 1Tone 1Tone 1
Ring Volume11375
Vibrate Cadence Off Telephone Off Off Telephone
Ring Delay00006
Noise Mode Normal Normal Normal Normal Normal
Headset/Speaker Speaker Speaker Speaker Speaker Speaker
Key Tones Off Off On On On
Warning Tones Off Off On On On
Push-to-talk* Off Off On On On
*Push-to-talk is only available on the SpectraLink 8030 model.
28
Advanced Features
Push-to-talk (PTT)
The PTT feature allows NetLink 8030 Series Wireless Telephones
to operate in a group broadcast mode that allows the handsets to
behave like walkie-talkies, where a single handset can transmit to
multiple listeners.
PTT is enabled by the system administrator and set up by the user
in the
Config Menu. See the Config Menu options for setting up
PTT. If the system administrator has disabled PTT, the PTT
options will not appear in the
Config Menu.
If you want to Then
Make a PTT call To call on the default channel, from
standby mode press and hold the
TALK
button. Wait for the display to show
Transmitting and then hold the handset
approximately two inches from your
mouth and speak.
Respond to a PTT call Press and hold the
TALK button during
the 10-second wait period.
End a wait period Press
END.
Select a different
PTT channel
Press and release the
TALK button.Use the
Nav keys or volume side buttons to
highlight the desired channel. Press
TALK
to transmit.
*
2
ABC
1
4
GHI
7
PQRS
3
DEF
0
FCN
LINE
6
MNO
9
WXYZ
#
5
JKL
8
TUV
*
2
ABC
1
4
GHI
7
PQRS
3
DEF
0
FCN
LINE
6
MNO
9
WXYZ
#
5
JKL
8
TUV
*
2
ABC
1
4
GHI
7
PQRS
3
DEF
0
FCN
LINE
6
MNO
9
WXYZ
#
5
JKL
8
TUV
*
2
ABC
1
4
GHI
7
PQRS
3
DEF
0
FCN
LINE
6
MNO
9
WXYZ
#
5
JKL
8
TUV
*
2
ABC
1
4
GHI
7
PQRS
3
DEF
0
FCN
LINE
6
MNO
9
WXYZ
#
5
JKL
8
TUV
Transmitter Receivers
29
Advanced Features
End one PTT call and
start another one
Press the END key to exit the PTT call.
Press and release the
TALK button and
select a different channel from the list.
Press and hold the
TALK button to begin
transmitting on the different channel.
Receive a PTT
call while on a
telephone call
Press the
END key to end the telephone
call. Now you can hear the PTT call.
Transmit on the
priority channel
Press and release the
TALK button. Select
the priority channel from the list. Press
and hold
TALK, then speak.
End a PTT call Press the
END key to exit the PTT call.
Change the
PTT volume
Press the up/down volume buttons on
the side of the handset while transmitting
or receiving a PTT call.
Answer a telephone
call during a PTT
transmission
Press the
START key. PTT transmissions
will be pre-empted by the telephone call.
Start a telephone call
during a PTT
transmission
Press the
START key and dial the number.
PTT transmissions will be pre-empted
during the telephone call.
Turn off PTT Change to a different profile (Silent and
Vibrate disable PTT by default).
Subscribe to
additional PTT
channels
Press the
Cfg softkey to open the Config
Menu
and select Push-to-talk.
Select
Subscribed Channels and then
select the channels you want to add.
Subscribed channels are marked with an
asterisk (*).
If you want to Then
30
Accessories
CHARGERS, BATTERY PACKS AND ACCESSORIES
Accessories for the NetLink 8000 Series Wireless Telephone
include three different charger models, three different Battery Pack
models, a headset and several carrying options.
Battery Packs
The Battery Packs must be recharged periodically. Each type of
Battery Pack requires a different amount of time to achieve a fully
charged state from a fully depleted state. Three Battery Pack
options are available
The Battery Pack icon on the status row indicates the charge
amount remaining. Additionally the handset will sound warning
tones and display the
Battery Low message when there are fewer
than two minutes of talk time remaining.
A melody will play when the handset is powered on for the first
time after being fully charged, unless this feature has been disabled.
Each Battery Pack type has a different melody.
See your system administrator if you have questions about the type
of Battery Pack you have been issued.
The Battery Pack can be changed while the call is still in progress.
Do not press
END. Quickly remove the discharged Battery Pack and
replace with a charged Battery Pack, press
END to turn the handset
back on and then press
START to resume the call.
Type Talk Time Standby Time Charging Time
Standard
4 hours 80 hours 2 hours
Extended
6 hours 120 hours 3 hours
Ultra-Extended
8 hours 160 hours 4 hours
The type of Battery Pack is printed on the label.
Remove the Battery Pack and view the label to
determine the type of Battery Pack you have been
issued.
31
Accessories
Charger Models
Three charger models are available for the NetLink 8000 Series
Wireless Telephone. The Single Charger will charge a single handset with an installed Battery Pack. The Dual Charger will charge the
handset and a spare Battery Pack. The Quad Charger can charge up
to four Battery Packs at a time. Any SpectraLink 8000 Series Battery Pack can be charged in any charger.
The Single and Dual Chargers allow the handset to remain operative in speakerphone mode or with a headset while charging. Handsets may be charged while in standby mode, while in an active call
or while turned off.
Place the Single or Dual Charger on a flat, horizontal surface. Plug
the power supply into the charger and into an appropriate wall outlet. The Quad Charger may be mounted on a horizontal or vertical
surface.
32
Accessories
Charging Status
The handset display and the LED on the Dual and Quad Chargers
indicate whether or not charging is occurring or completed or if a
Battery Pack failure has been detected.*
Handset/LED Charging Status
Charging
LED Solid On
The Battery Pack in the handset is
charging.
Note that in the Dual Charger, the
handset’s Battery Pack takes charging
precedence, and when it is finished
charging, the single Battery Pack in the
rear slot will charge.
Charge Complete
LED Off
The Battery Pack in the handset has
finished charging.
Battery Pack fully charged, empty slot, or
unit is not powered.
Battery Failure
LED Flash
Error. Battery Pack not able to be
charged. Reinsert Battery Pack or replace
Battery Pack.
* Note: the Single Charger does not have an LED indicator.
33
Accessories
Single Charger
The Single Charger is designed to allow the handset to remain
operational through speakerphone or headset use while the handset's Battery Pack is being charged. The handset may also be
charged while it is in standby mode or turned off.
Place the handset in the Single Charger facing forward. While the
handset is charging in standby mode, it will display its extension
number and
Charging…
. An animated charge icon will indicate that
charging is in progress. The handset is fully operational and will ring
if called. When the handset is charging while turned off, only
Charg-
ing…
will display and no calls will be received. The dots will be rac-
ing during the charging cycle.
When the handset is fully charged, Charge Complete will display.
No charging information will display during an active call.
<
*
0
FCN
LINE
8
TUV
5
JKL
2
ABC
7
PQRS
4
GHI
1
3
DEF
6
MNO
9
WXYZ
# >
34
Accessories
Dual Charger
The Dual Charger is designed to charge the Battery Pack in the
handset while it remains operational and also charge an additional
Battery Pack in the rear charging bay. The handset has charging priority when both slots are occupied.
Place the handset in the front slot, facing forward. The Battery
Pack alone snaps into the charging bay as shown in the illustration.
The LED indicates the status of the Battery Pack in the rear bay.
The handset displays its charging status as described for the Single
Charger.
When the handset is fully charged or is removed, the Battery Pack
will begin charging.
Note that the time it takes for the Battery Pack to charge will be
lengthened if its charging cycle is interrupted for a handset to charge.
<
*
0
FCN
LINE
8
TUV
5
JKL
2
ABC
7
PQRS
4
GHI
1
3
DEF
6
MNO
9
WXYZ
# >
LED indicator
35
Accessories
Quad Charger
The Quad Charger is designed to simultaneously charge four Battery Packs. It may be mounted on a horizontal or vertical surface.
The Battery Pack snaps into the charging slot. The LED above the
occupied bay indicates the charging status of the Battery Pack in
the bay.
A flashing LED may indicate a Battery Pack failure.
Verify the condition of the Battery Pack by the following procedure before replacing it. First check
the Battery Pack in a different bay or substitute
another charger and repeat the operation that
caused the failure. If the same Battery Pack lights
a steady LED when inserted in a different bay or
charger, the first charger may be faulty. Contact
your system administrator for service information.
36
Accessories
Carrying Options
The following options are available for handset protection and easy
handset carrying and removal.
Belt clip: Spring-loaded plastic belt clip that attaches to the back of
the handset.
Swivel belt clip: Swivel-style belt clip that attaches to the back of
the handset with full 360 degree swivel or eight-position ratchet
options.
Swivel carrying case: Black leather case with keypad cover and
swivel-style quick release belt clip.
Rugged holster: Black holster with belt clip.
Cord lanyard: Nylon cord lanyard with quick disconnect.
Coiled lanyard: Plastic coiled lanyard with clothing clip.
Headsets
SpectraLink offers optional headsets (for North American only)
for use in noisy environments or if you need to have your hands
free while talking on the handset.
To use the headset, simply plug it into the jack on the right side of
the handset.
While using a headset, the handset will ring according to the user
profile setting established in the
Headset/Speaker Ring option. The
external ring will ring according to the setting of the profile.
The headsets offered by SpectraLink are specially designed to work
properly with the NetLink 8000 Series Wireless Telephone.
SpectraLink does not recommend using other headsets.
37
Administration
HANDSET ADMINISTRATION
FAQs
How does the handset power off and power on?
The END key is the power on/power off key. Press and hold it to
turn the handset on. Turn the handset off from the standby mode
by pressing and holding the
END key. If you are in an active call, end
the call by pressing the
END key. This returns the handset to the
standby mode, then press
END again to turn the handset off.
How do I place a call and terminate a call?
To place a call, press the
START
key and then dial the number. End
the call by pressing the
END
key. You can also use the speakerphone
instead of the
START
key.
Can I change the ring?
The ring is fully adjustable and may be set differently for different
profiles. For a complete explanation of how to change the ring, see
the Profile Settings section of this guide.
How do I change the voice volume and the ringing volume?
Whether using a headset, the speakerphone, or the internal
speaker, the speaker volume for the current call may be raised or
lowered by pressing the up and down volume buttons on the side
of the handset.
The volume buttons may be pressed while the handset is ringing to
raise or lower the ring volume, which also changes the ring volume
setting in the current profile.
What is the range of the NetLink 8000 Series Wireless
Telephone?
As barriers affect radio transmission, there is no single answer for
this question. Normally, you can expect the same range as with any
other wireless device. However, if your facility has metal walls or
other materials that inhibit radio waves, the range will be reduced.
How do I charge the Battery Pack?
The Battery Pack in the handset may be charged in a Single or Dual
Charger without being removed from the handset by simply plac-
38
Administration
ing the handset into the charger. A spare Battery Pack may be
charged in the rear bay of the Dual Charger or in a Quad Charger.
How long does the Battery Pack hold a charge?
There are three different Battery Pack models and each has a different charge capacity. The type of Battery Pack is printed on the
label. Remove the Battery Pack and view the label to determine the
type of Battery Pack you have been issued.
What features (transfer, mute, etc.) are available and how are
they activated?
Active call features such as Mute and Hold are available by pressing
the softkey programmed to the feature. Additional features, such as
Transfer and Conference, are locally programmed and usually activated by pressing the
FCN key and then the softkey that corre-
sponds to the programmed feature. Contact your phone system
administrator for detailed information on how to access these features in your facility.
Can I use the NetLink 8000 Series Wireless Telephone at home?
Access points installed in your facility transmit the radio waves emitted by your NetLink 8000 Series Wireless Telephone to the telephone system in your facility which links the handsets to each other
and to the rest of the world. The handset operates only within range
of these access points and therefore will not work in your home.
How should I clean the handset?
Wiping the handset surface with a water-dampened cloth or paper
towel will remove most films or residues. If the soiling is too stubborn for plain water, a mild detergent solution may be used. A spray
cleaner may be used with care. Do not spray at an angle. Do not allow
liquid cleaners to seep into keypad. Be sure to wipe away any detergent residue with a clean water-dampened cloth. Do not immerse in
any fluid.
Type Talk Time Standby Time Charging Time
Standard
4 hours 80 hours 2 hours
Extended
6 hours 120 hours 3 hours
Ultra-Extended
8 hours 160 hours 4 hours
39
Administration
Specifications
Radio frequency
(set by system
administrtator)
802.11b, 802.11g 2.4–2.4835
802.11a 5.150–5.250
5.250–5.350 DFS
5.470–5.725 DFS
5.725–5.825 DFS
Transmission type Direct-sequence spread spectrum (DSSS)
Transmit data rate Up to 54 Mb/s
Radio QoS SpectraLink Voice Priority (SVP)
Wireless security Wired Equivalent Privacy (WEP), 40-bit
and 128-bit; Cisco FSR; WPA-PSK,
WPA2-PSK
FCC certification Part 15.247
Management DHCP, TFTP
Voice encoding G.711, G.729a/ab
VoIP Protocols SpectraLink Radio Protocol (SRP)
Transmit power Set by system administrator.
Display
Up to five lines of text plus two icon status
rows and one row for softkey labels.
NetLink 8020 Wireless
Telephone dimensions
5.4" x 2.0" x 0.9"
(13.7 x 5.1 x 2.3 cm)
NetLink 8030 Wireless
Telephone dimensions
5.7" x 2.0" x 0.9"
(14.5 x 5.1 x 2.3 cm)
NetLink 8020 Wireless
Telephone weight
3.9 oz. ( 110.6 g) with
Standard Battery Pack
NetLink 8030 Wireless
Telephone weight
4.2 oz. (119.1 g) with
Standard Battery Pack
Standard Battery Pack
capacity
4 hours talk, 80 hours standby
Extended Battery Pack
capacity
6 hours talk, 120 hours standby
Ultra-Extended Battery
Pack capacity
8 hours talk, 160 hours standby
40
Administration
Notes
41
Administration
Notes
42
Administration
Notes
43
Administration
Notes
44
Administration
Notes
45
Index
A
Accessories
Battery Packs 30
Carrying options 36
Chargers 31
Headset 36
Active mode 8
Administration
Care of handset 47
FAQs 37
Handset Operation Summary 14–18
Specifications 39
Answer call
First line 16
Second line 16
Via headset 16
B
Backlight 18
Battery Packs
Charging 32–35, 37–38
Charging status 32
Dual Charger 34
Options 30
Quad Charger 35
Remove/replace 14
Single Charger 33
C
Care of handset 47
Carrying options 36
Chargers
Charging status 32
Cleaning the handset 47
Dual Charger 34
Quad Charger 35
Single Charger 33
Use of 31–35
Cleaning handsets and chargers 38
Config menu
Default profile settings 27
Defined 23
Entering 23
Mode 8
Options diagram 24, 25
Profiles 26
D
Data entry 20
Data entry table 20
Dial call
Outgoing calls 15, 37
Via phonebook 21
Displays, handset 9
E
Edit
Arrows during 10
Data entry 20
Phonebook 21
Speed-dial number 22
Emergency call 15
External call 15
F
Features
Config menu 23
Config menu options 24
Data entry and editing 22
Display additional 18
Facility-specific 19
Phonebook 21
Predial 19
Push-to-talk (PTT) 28
Redial 19
Speakerphone 19
Speed-dial 22
H
Handset Operation Summary 14–18
Hang up 14, 17
Headset
Answer 16
Cleaning connector 47
Profile setting 27
Use of 36
Volume 17
46
Volume with 37
While charging 31, 33
Hold
Place a call on 16
Softkey label 12
I
Internal call 15
K
Keypad
Cleaning 38, 47
Cover 36
Illustration 2, 3
Lock 9, 11, 15
Unlock 13, 15
M
Menu navigation 8
Modes of operation 8
Mute
On status bar 11
Softkey label 13
Use of 17, 38
N
Navigation 8
P
Phonebook
Call 16
Edit 17
Edit entry options 22
Features 21
List options 21
Open 13
Save to 19
Predial
Use of 15, 19
Push-to-talk (PTT)
Defined 28
Mode 8
Operation summary 28
R
Range 37
Redial
Softkey label 13
Use of 16, 19
S
Shortcut key 9, 19
Softkey
Active 12
Labels 12, 13
Speakerphone
Answer with 16
Icon 10
Softkey label 13
Use of 17, 19, 37
Volume with 37
While charging 31, 33
Specifications 39
Speed-dial
Open speed-dial list 16, 21
Softkey label 13
Use of 16, 22
Standby mode 8
Status indicators 10–11
System administrator 5
U
User profile
Changing 17
Headsets and 36
Setting 26–27
V
Volume
Changing 37
Headset 17
Ring 17, 27
47
CARE OF YOUR HANDSET
• Avoid dropping the handset or knocking it against hard surfaces. Carrying the handset in a holster or carrying case will help protect it.
• There are no serviceable parts in the handset or chargers. You should
not open the handset case or disassemble the chargers. Doing so will
void your warranty.
• Turn off the handset and unplug chargers before you clean them. Take
care not to exert undue pressure on charger electrical contacts while
wiping.
• Wiping the handset surface with a water-dampened cloth or paper
towel will remove most films or residues. If the soiling is too stubborn
for plain water, a mild detergent solution may be used. A spray cleaner
may be used with care. Do not spray at an angle. Do not allow liquid
cleaners to seep into keypad. Be sure to wipe away any detergent residue with a clean water-dampened cloth. Do not immerse.
• Should the headset connector become dirty, you may experience a
scratchy or intermittent signal. To clean the connector, dip the nonpadded end of a wooden or paper cotton swab stick in isopropyl alcohol. Gently insert in the connector and twist, repeating several times. If
available, blow compressed air into the connector to clear debris.
• Keep the headset jack covered when it is not in-use.
• Using a carrying case may help protect the surfaces and help prevent
liquids (e.g., rain) from entering into the interior of the handset.
• If your handset interior gets wet, do not try to accelerate drying with
the use of an oven or a dryer as this will damage the handset and void
the warranty. Instead, do the following:
1. Immediately power off the handset.
2. Remove the Battery Pack from handset.
3. Shake excess liquid from the handset.
4. Place the handset and Battery Pack in an upright position in an area
that is at room temperature and has good airflow.
5. Let the handset and Battery Pack dry for 72 hours before recon-
necting the Battery Pack and/or powering on the handset.
If the handset does not work after following the steps listed above,
contact your phone system administrator for servicing information.
NETLINK 8000 SERIES WIRELESS TELEPHONE
AND ACCESSORIES USER GUIDE
SpectraLink Corporation
5755 Central Avenue
Boulder, CO 80301
303 440 5330
800 676 5465
www.spectralink.com
Trademark Information
SpectraLink
NetLink
Are trademarks and registered trademarks of SpectraLink Corporation.
The SpectraLink logo is a registered trademark in the United States of America
and in other countries.
Copyright © 2007 SpectraLink Corporation.
All rights reserved
Information in this document is subject to change without notice and does not
represent a commitment on the part of SpectraLink Corporation. The software
described in this document is furnished under a license and/or copyright and may
only be used with the terms of SpectraLink’s software license agreement as found in
this manual or at
http://www.spectralink.com/consumer/resources/software_updates.jsp.
The software may be used only in accordance with the terms of the agreement. No
part of this manual, or the software described herein, may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying
and recording, for any purpose except for the sole intent to operate the product or
without the express written permission of SpectraLink Corporation.
P/N 72-1301-00-B
Loading...