Speco Technologies SIPSD37X, HTSD37X User Manual

SIPSD37X & HTSD37X
37X Optical Indoor / Outdoor Speed Dome Cameras
200 New Hightway
Amityville, NY 11701
631-957-8700
Speco Technologies is constantly developing product improvements. We reserve the right to
modify product design and specifications without notice and without incurring any obligation.
Rev. 03082010.
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN THE COVERS.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONAL
This lightning flash with arrowhead symbol is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
This Device compiles with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interface, and (2) This device must acc ept any interference received, including inte rference that
may cause undesired operations.
37X Speed Dome Camera 2/50
Important Safety Guide
NOTICE
1. Read and follow all the Instructions
Read all the safety and operating instructions before using the product.
2. Keep this manual
Keep this manual for reference in future.
3. Attachments / Accessories
Use only the attachments or accessories specified by the manufacturer.
4. Installation z Do not install near any heat sources such as radiators, heat registers, stoves, or other
appratus including amplifiers that product heat.
z Improperly installed product may fall, cause serious injury to a child or adult and
damage the product.
z Do not block any ventilation holes or openings. Install in accordance with the
manufacturer’s instructions.
z Use only with the cart, stand, tripod, bracket, mounting devices, or table specified by
the manufacturer.
z Installation should be done only by qualified personnel and conform to all the
instructions by the manufacturer.
z Refer all servicing to qualified service personnel. z Use stainless steel hardware to fasten the mount. z To prevent damage from water leakage when installing a mount outdoors on a roof or
wall, apply sealant properly around holes.
z These servicing instructions are for use by qualified service personnel only. To reduce
the risk of electric shock, do not perform any servicing other that contained in the operationg instructions unless you are qualified to do so.
z Use only replacement parts specified by the manufacturer.
5. Power source
This product should be operated only from the type of the power source indicated on the marking label.
37X Speed Dome Camera 3/50
Operating
Handling
Installation and Storage
Caution
z Before using, make sure that the power supply is properly installed. z While operating, if any abnormal condition or malfunction is observed, stop using the
product immediately and then contact your local dealer.
z Do not disassemble or tamper with the parts inside the product. z Do not drop or subject the product to shock and vibration as this can damage the
product.
z Care must be taken when you clean the clear dome cover. Especially, scratch and dust
will ruin the quality of the product.
z Do not install the product in areas of extreme temperature, which exceed the allowable
range.
z Avoid installing in places where radiation is present. z Avoid installing in places where there are strong magnetic fields and electric signals. z Avoid installing in places where the product would be subject to strong vibrations.
NOTICE
37X Speed Dome Camera 4/50
g
Package Components
Main Part Description
Installation with Wall Mount Bracket
Wiring and Cabling
Check Points before Operation
Check Points for Preset and Pattern Function before
Reserved Preset (Hot Keys)
Quick Programming Guide
Privacy Zone Mask Setup
System Initialization
Specifications
37X Speed Dome Camera 5/50
TABLE OF CONTENTS
Introduction
Feat ure s
Installation
DIP Switch Setup
Operation
Operation
OSD Menu
Preset
Swing
Pattern
Group
Other Functions
OSD Display
OSD Menu
Main Menu
Display Setup
Camera Setup
Motion Setup
Preset Setup
Setup
Swin
Pattern Setup
Group Setup
Dimensions
Wa r ra n ty
24
41
6
9
10
11
14
15
18
18
19
19
20
20
21
22
22
25
25
26
27
29
34
37
39
40
44
45
48
49
Fe at ur es
Powerful Zoom Camera & Setup Options
z Image Sensor: Sony 1/4" Double density interline transfer CCD z Zoom: 37X Optical Zoom, 12X Digital Zoom
z Day & Night, Privacy Mask and WDR z SNR (Super Noise Reduction) Function z Various Focus Modes: Auto-Focus, Manual Focus, Semi-Auto Focus
z Various Setup Options in OSD Menu.
Powerful Pan/Tilt Functions
z MAX. 360°/sec High Speed Pan/Tilt Motion z With the Vector Drive Technology, Pan/Tilt motions are accomplished along the
shortest path. As a result, the time to target view is remarkably shortened and the video on the monitor is very natural.
z With the Micro-Stepping Control Technology, the video looks very natural at high
zoom magnification during a jog operation on a controller since the camera can be controlled by 0.05°/sec. Hence it is very easy to make the camera focus on desired target views at high zoom magnification. Additionally it is easy to make the camera focus on desired positions with zoom-proportional pan/tilt movement.
Preset, Pattern, Swing, Group, Privacy Mask and More…
z MAX. 127 Presets are programmable and each preset can have its own parameter
values independently from the other presets. For an example, refer to the below table.
Preset No. White Balance Auto Exposure ••• Label Remarks
Preset 1 Case A Case 3 “ENTRANCE”
Preset 2 Case C Case 5 “WAREHOUSE”
•••
Preset 95 Reserved for OSD Menu
•••
Preset 128 Case K Case 9 “TERRACE”
INTRODUCTION 1
37X Speed Dome Camera 6/50
z MAX. 8 sets of Swing are programmable. This function is that the camera moves
repetitively between two preset positions at programmed speeds.
z MAX. 4 Patterns are programmable. This function is that the camera memorizes the
path (mostly curve path) by the joystick of the controller and revives the trajectory operated by the joystick as closely as possible.
z MAX. 8 sets of Group are programmable. This function is that the camera memorizes
the combination of Presets, Pattern and/or Swings sequently and runs Presets, Pattern and/or Swings repetitively. A Group can be combined upto 20 functions with any of Preset/Pattern/Swing.
z MAX. 8 or 4 Privacy Masks are programmable, not to intrude on any other’s privacy.
PTZ(Pan/Tilt/Zoom) Control
z With the RS-485 communication connection, MAX. 255 units of cameras can be
connected to a single controller.
z Pelco-D or Pelco-P protocols can be selected as a control protocol in the current
firmware version.
OSD(On Screen Display) Menu
z OSD menu is provided to display the status of camera and to configure the functions
interactively.
z The information such as Camera ID, Pan/Tilt Angle, Direction, Alarm Input and Preset
is displayed on screen.
Alarm In/Out Function(Only for the models which have I/O function)
z 3 alarm sensor inputs and 1 alarm sensor outputs are available. z Alarm sensor input is decoupled with photo-couplers to avoid external electric noise
and shock perfectly.
z Both of N.O.(Normal Open) sensors and N.C.(Normal Close) sensors can be used and
the signal range of the sensor input is from DC 5.0V to 12.0V for various applications.
z The camera can be set to move to a Preset position or to run functions such as Pattern,
Swing and Group when there are external sensor activations. Also “Post Alarm” function is possible, which is supposed to activate after user-defined time period and
Reserved Presets(Hot Keys)
sequentially in succession to the action by external sensor activations.
z Most camera setup options can be set up easily and directly with the reserved presets
(Hot Keys), without entering into OSD menu. For more information, refer to “Reserved Presets(Hot Keys)” in this manual.
INTRODUCTION 1
37X Speed Dome Camera 7/50
Network Function(Only for the SIPSD37X)
z Network functions including remote monitoring, bidirectional audio and others are
available through IP based network such as LAN, ADSL/VDSL, and Wireless LAN. For
more information, refer to the separated manual for IP Addressable models.
Perfect Outdoor Environment Compatibility and Easy Installation
z The fans and heaters are built-in in the camera for cold and hot temperature
environment. Also idealistic mechanical design protects the camera from water and dust. (IP67 when installed properly with wall mount bracket only / Only for outdoor models)
INTRODUCTION 1
37X Speed Dome Camera 8/50
Product & Accessories
Package Component
INTRODUCTION 1
z Main Body & Surface Mount Bracket z Default Accessories
z Accessories for The Models with Alarm
In/Out Function [I/O Cable]
Wall Mount Brackets (Included)
[Main Cable, Wrench]
z Accessories for The IP Addressable Models
[Crossover LAN Cable, Audio Cable, CD]
SIPSD37X Only
[Screws : Machine M5×15, Hex Lag #14×50]
37X Speed Dome Camera 9/50
)
Main Part Description
INTRODUCTION 1
Mounting Screw Hole
Drop Prevention Spring
DIP Switch
Reset Switch (IP Model) LAN Port (IP Model) Audio Port (IP Model) Main Connector Sensor I/O Port (I/O Model
Dome Cover
z Dome Cover Do not detach the protection vinyl from the dome cover before
finishing all the installation process to protect the dome cover from scratches or dust.
z DIP Switch Used to set up camera IDs and protocols.
z Drop Prevention
Spring
This part keeps the camera from dropping during installation and maintenance. After install the Bracket, please, hang the spring to the drop prevention hook of main body as shown in picture for further tasks.
z Mounting Screw Hole Used to assemble the main body with a bracket with screws.
z Main Connector Use d for t h e powe r wire, t he vi deo c a ble a nd th e RS-4 85
communication cable connection.
z Sensor I/O Port Used for the sensor in/out connection. (The sensor I/O function
possible models only)
z LAN Port Used for the Ethernet connection. (IP addressable models only)
z Audio Port Used for the audio in/out connection. (IP addressable models
only)
z Reset Switch Used to initialize all the network configurations to the factory
default. (IP addressable models only) Press the button for more than 5 seconds to initialize the network system.
37X Speed Dome Camera 10/50
N
INSTALLATION 2
DIP Switch Setup
Before installing the camera, set up the DIP switch to configure the camera ID and the communication protocol.
Camera ID Setup
ON
O
12345678
z ID numbers of cameras are set up with binary numbers.
See the examples shown below.
Pin 1 2 3 4 5 6 7 8
Binary Value 1 2 4 8 16 32 64 128
ex) ID=5 on off on off off off off off ex) ID=10 off on off on off off off off
z The camera ID range is “1~255”. Camera ID must not be
“0”!
z The factory default of the camera ID is “1”. z Match the camera ID with the Cam ID setting of your DVR
or Controller to control the camera.
z If you are connecting a single camera to a controller,
terminate the camera. When connecting more than one camera to a single controller, terminate the last camera on the communication line. The last camera means the camera farthest in cable length from the controller.
z Note that the total length of the communication cable
between a controller and the camera(s) on the same communication line must be less than 1.2Km.
37X Speed Dome Camera 11/50
Communication Protocol Setup
z Select an appropriate Protocol with the DIP switch combination.
ON
ON
1234
P0
(Pin 1)
OFF OFF OFF PELCO-D, 2400 bps
ON OFF OFF PELCO-D, 9600 bps
OFF ON OFF PELCO-P, 4800 bps
ON ON OFF PELCO-P, 9600 bps
z Match the camera protocol with the camera protocol in the setting of
your DVR or controller to control the camera.
z Adjust the DIP switch after turning off the camera. If you changed the
camera protocol by changing the DIP S/W, the change will be effective after you reboot the camera.
z The factory default protocol is “Pelco-D, 2400 bps”. (HTSD37X) z The factory default protocol is “Pelco-D, 9600 bps”. (SIPSD37X)
INSTALLATION 2
Switch Mode
P1
(Pin 2)
P2
(Pin 3)
Protocol
Others Reserved
37X Speed Dome Camera 12/50
T
Terminal Resistor Setup
ON
ON
1234
INSTALLATION 2
he terminal resistor is used for the following cases.
z Case 1 : In case that the control cable length between a camera
and a controller is relatively very long (1:1 Connection)
If the communication cable length is very long, the electrical signal will bound in the terminal point. This reflected signal causes distortion of original signal. Accordingly, the camera can be out of control. In this case, the terminal resistor of both sides i.e. the camera and the controller must be set to ‘ON’ state.
z Case 2 : In case that multiple cameras are connected to a
controller.
Due to similar reasons with the case 1, the terminal resister of the controller and the last camera must be set to ‘ON’ state. The last camera means the camera farthest in cable length from the controller. Do not turn on the terminal resistor of all the cameras on the same communication cable.
Controller
Terminal Resistor ON
RS-485
#1 #2 #n
Terminal Resistor
OFF
Terminal Resistor
OFF
Terminal Resistor
ON
37X Speed Dome Camera 13/50
Make a hole whose diameter is 30~40mm
Line up the mold lines and assemble
Installation with Wall Mount Bracket
on the mounting surface to pass the wire(s) and cable(s) through the mounting surface. (In case of the wiring and cabling through the mounting surface only) Then prepare the wall mount bracket. Pull the wire(s) and cable(s) for the system as below. Attach the wall mount bracket to the mounting surface. (Hex Lag #14×50)
main body to mount adaptor and turn it. And assemble the main both with the camera mount adaptor with the 3 screws. (Machine M5×15).
INSTALLATION 2
Hook up “Drop Prevention Spring” on
main body to prevent camera from unexpected drop and pull the wire(s) and cable(s) for the system as below.
Screw the dome cover to the main body
and remove the protection vinyl from the dome cover.
Important Notice
z Before starting the installation, make sure that the Camera ID and Protocol are set up properly.
37X Speed Dome Camera 14/50
A
R
R
Wiring and Cabling
BROWSER
MIC SPEAKER
Port Description
z Main Cable
Port Pin Number (RJ45) Connector / Wire Color Signal
z I/O Cable
Port Pin Number (RJ25) Wire Color Signal
INTERNET
LAN CABLE
UDIO
CABLE
MAIN CABLE
POWER
BNC
RS-485
I/O CABLE
INSTALLATION 2
MONITO
CONTROLLER / DVR
SENSOR I/O
I SENSOR
DOOR SWITCH
1 Video +
2,4
BNC Connector
Video
5 Red RS-485 +
3 Yellow RS-485
7 Orange Power +
6,8 White Power
1 Blue IN COM +
2 Yellow IN 1
3 Green IN 2
4 Red IN 3
5 Black OUT A
6 White OUT B
37X Speed Dome Camera 15/50
INSTALLATION 2
Power Description
z Carefully check the voltage and current capacity of the rated power. The rated power is
indicated in the back of main unit.
24VAC is used on the HTSD37X (AC 17V~29V, 1.5A)
12VDC is used on the SIPSD37X (DC11V~18V, 3.0A)
z For the DC input models, be careful with the polarity of DC power. The system should be
permanentally damaged by wrong DC input.
z In case that the length of the power wire is very long, there may be voltage drop and the
syatem may not work properly. Make the length of the power wire as short as possible.
RS-485 Communication (HTSD37X ONLY)
z For PTZ control, connect the cable(s) to your keyboard or DVR. To connect multiple
cameras to a single controller, RS-485 communication should be connected in parallel as shown below. If you are connecting a single camera to a controller, terminate the camera. When connecting more than one camera to a single controller, terminate the last camera on the communication line. The last camera means the camera farthest in cable length from the controller. Note that the total length of the communication cable between a controller and the camera(s) on the same communication line must be less than 1.2Km.
CONTROLLER / DVR
RS-485
-
+
-
+
-
+
-
+
#1
#2
#n
37X Speed Dome Camera 16/50
Video
z Use BNC coaxial cable only.
Alarm Input
Before connecting sensors, check driving voltages and output signal types of the sensors. Since output signal types of the sensors are divided into Open Collector type and Voltage Output type in general, the wiring must be done properly after considering those types.
Signal Description
IN COM+ The electric power source to drive input circuit. Connect the (+) wire of electric
IN1 -, IN2 -, IN3 - Connect the outputs of sensors to each port as shown in the above
If you want to use Alarm Input, the types of sensors must be selected in OSD menu. The sensor types are divided into Normal Open and Normal Close. If wrong sensor types are selected, alarms should be activated reversely to sensor inputs.
~ Normal Open Output Voltage is high state when sensor is activated
~ Normal Close Output Voltage is high state when sensor is not activated
Relay Output
The maximum loads are as follows.
Power Type DC Power AC Power
Maximum Load MAX. 24VDC, 1A MAX. 125VAC, 0.5A
INSTALLATION 2
Internal
IN COM+
IN 1-
IN 3-
Sensor 1
Sensor 3
power source to drive the Sensors to this port as shown in the above circuit.
circuit.
Internal
OUT 1
AC or DC
LOAD
+
+
+5V~12V
+
-
-
-
37X Speed Dome Camera 17/50
z Before turning on the system, check if the wire(s) and cable(s) are connected properly. z Check if the camera ID on the controller is properly selected. The camera ID must be
z If your controller supports multi-protocols, the protocol must be changed to match to that of z Adjust the DIP switch after turning off the camera. If you changed the camera protocol by z Since the operation method can be different by controllers, refer to your controller manual
z Check fully how to operate preset function and pattern function with your controller or DVR
z Refer to the following table when using standard Pelco® protocol controllers.
z If your controller or DVR has no pattern button or function, use the Hot Keys with preset
Check Points before Operation
identical to that of the target camera. The camera ID can be checked by reading the DIP switch of the camera or on OSD.
the camera.
changing the DIP S/W, the change will be effective after you reboot the camera.
if the camera can not be controlled properly. The operation of this manual is based on the standard Pelco® Controller.
Check Points for Preset and Pattern Function before Operation
in advance to operate the camera functions when using a controller or a DVR.
< Go Pres et > Input [Preset Number] and press [Preset] button shortly.
< S et Pres et > Input [Preset Number] and keep pressing [Preset] button for more than 2 seconds.
< Run Pat tern > Input [Pattern Number] and press [Pattern] button shortly.
< S et Pa tter n > Input [Pattern Number] and keep pressing [Pattern] button for more than 2 seconds.
numbers. For more information, refer to “Reser ved Presets(Hot Keys)” in this manual.
OPERATION 3
37X Speed Dome Camera 18/50
z Function With OSD menu, the system can be properly configured for each
z Entering into OSD Go Preset [95]
z Description Some Preset numbers are reserved to change some parameters without entering
z Hot Keys
Go Preset [131~134]
Go Preset [141~148]
Go Preset [151~158]
Go Preset [161] : Turning off Relay Output
Set Preset [161] : Turning on Relay Output
Go Preset [167] : Setting Zoom Proportional Function to ON
Set Preset [167] : Setting Zoom Proportional Function to OFF
Go Preset [170] : Setting Camera BLC/WDR Mode to OFF
Go Preset [171] : Setting Camera BLC/WDR Mode to ON
Go Preset [174] : Setting Camera Focus Mode to AUTO
Go Preset [175] : Setting Camera Focus Mode to Manual
Go Preset [176] : Setting Camera Focus Mode to SEMI-AUTO
Go Preset [177] : Setting Day & Night Mode to AUTO
Go Preset [178] : Setting Day & Night Mode to NIGHT
Go Preset [179] : Setting Day & Night Mode to DAY
Go Preset [190] : Setting OSD Display Mode to AUTO (Except Privacy Mask)
Go Preset [191] : Setting OSD Display Mode to OFF (Except Privacy Mask)
Go Preset [192] : Setting OSD Display Mode to ON (Except Privacy Mask)
Go Preset [193] : Setting all Privacy Mask Display to OFF
Go Preset [194] : Setting all Privacy Mask Display to ON
OSD Menu
application.
Reserved Presets (Hot Keys)
into OSD menu.
Go Preset [95] : Entering into OSD menu
: Running Pattern Function 1 ~ 4
: Running Swing Function 1 ~ 8
: Running Group Function 1 ~ 8
OPERATION 3
37X Speed Dome Camera 19/50
OPERATION 3
Preset
z Function MAX. 127 positions are programmable. The Preset number can be
assigned from 1 to 128 except 95. Preset 95 is reserved for entering into OSD menu. Camera parameters such as White Balance, Auto Exposure and others can be set up independently and each preset can have its own parameter values independently from the other persets. When setting up presets with a controller, Label should be blank and "Camera Adjust" should be set to "GLOBAL" as the default. To change the parameters, enter into OSD menu.
z Setting Presets Set Preset [1~128]
z Running Presets Go Preset [1~128]
z Deleting Presets To delete Presets, enter into OSD menu.
Swing
z Function This function is that the camera moves repetitively between two
preset positions at programmed speeds. When a swing function runs, the camera moves from the preset assigned as the 1st point to the preset assigned as the 2nd point in CW(Clockwise) direction. Then the camera moves from the preset assigned as the 2nd point to the preset assigned as the 1st point in CCW(Counterclockwise) direction.
1
CW
n
o
i
t
c
e
r
i
D
CCW
2
D
e
r
i
n
o
i
t
c
2nd Preset
1st Preset
In case that the preset assigned as the 1st point and the preset assigned as the 2nd point are same, the camera turns on its axis by 360° in CW(Clockwise) direction and then it turns back on its axis by 360° in CCW(Counterclockwise) direction. The Swing speed is defined from 1°/sec to 180°/sec.
z Setting Swings To set Swing, enter into OSD menu.
z Running Swings
Method 1) <Run Pattern> [Swing NO. + 10] Method 2) <Go Preset> [Swing NO. + 140]
ex) Run Swing 3 : <Run Pattern> [13] ex) Run Swing 3 : <Go Preset> [143]
z Deleting Swings To delete Swings, enter into OSD menu.
37X Speed Dome Camera 20/50
OPERATION 3
Pattern
z Function This function is that the camera memorizes the path (mostly curve
path) by the joystick of the controller and revives the trajectory operated by joystick as closely as possible.
MAX. 4 Patterns are programmable and Maximum 1200 communication commands can be programmed in a pattern.
z Setting Patterns A Pattern can be created by the following methods.
Method 1) <Set Pattern> [Pattern NO.]
{ The Pattern programming window appears on the monitor as
below.
EDIT PATTERN 1
[NEAR:SAVE /FAR:DELETE] 0/0/x1/N
{ The movement by Joystick and the preset movement can be
memorized in a pattern.
{ After a pattern is programmed, the remaining storage is
displayed in progress bar on the screen.
{ To save the recording, press NEAR key and to cancel, press
FAR key.
Method 2) Programming in OSD Menu : See the section “How to use OSD Menu”.
z Running Patterns
Method 1) <Run Pattern> [Pattern NO.] Method 2) <Go Preset> [Pattern NO. + 130]
ex) Run Pattern 2 : <Run Pattern> [2] ex) Run Pattern 2 : <Go Preset> [132]
z Deleting Patterns To delete Patterns, enter into OSD menu.
Note) When the system memorizes Patterns, the commands are stored in the momories, not the positions of Pan/Tilt/Zoom. Hence there might be small differences between the original path and the revived path by path type of Patterns. Note that it is not a problem in position precision.
37X Speed Dome Camera 21/50
OPERATION 3
Group
z Function This function is that the camera memorizes the combination of
Presets, Pattern and/or Swings sequently and runs Presets, Pattern and/or Swings repetitively. MAX. 8 sets of Group are programmable. Each group can have MAX. 20 actions which are the combination of Preset, Pattern and Swing. Preset speed can be set up and the repeat number of Pattern & Swing can be set up in Group setup. Dwell time between actions can be set up also.
Dwell Time
Preset 1 Pattern 1 Swing 1
Max 20 Entities
z Setting Groups To set Groups, enter into OSD menu.
z Running Groups
Method 1) <Run Pattern> [Group NO. + 20] Method 2) <Go Preset> [Group NO. + 150]
ex) Run Group 7 : <Run Pattern> [27]
ex) Run Group 7 : <Go Preset> [157]
z Deleting Groups To delete Groups, enter into OSD menu.
Other Functions
z Power Up Action This setting defines a specific activity (Preset, Pattern, Swing and
z Auto Flip In case that tilt angle arrives at the top of tilt orbit(90°), zoom module
z Parking Action This feature allows the camera to begin a specified operation after a
Group) to be performed in the event that the power to the camera is cycled. This function enables the user to resume, after turning on power, the last action being executed before turning off the power. Most of actions such as Preset, Pattern, Swing and Group are available for this function but Jog actions are not available to resume.
camera turns on its axis by 180° at the top of tilt orbit and moves to opposite tilt direction (180°) to keep tracing targets.
programmed time of inactivity. This function makes the camera automatically run a pre-defined action if there is no command from controller for a pre-defined time period. “Wait Time” means how long a camera should wait for from the previous-last (most recent) command before running the pre-defined action. It can be set to 1 second ~ 3 hours.
37X Speed Dome Camera 22/50
OPERATION 3
z Alarm Input 3 Alarm Inputs are available. When external sensors activate, the
camera runs pre-defined actions such as Preset, Pattern, Swing and Group. After the pre-defined time period passed, “Post Alarm” activates, which is pre-defined. Note that only the latest alarm input is effective when multiple sensors are activated at the same time.
z Privacy Zone Mask Privacy Zone Mask allows the user to program 8(or 4) rectangulars
that can not be viewed by the operator of the system. To protect others’ privacy, MAX. 8(or 4) Privacy Masks can be created on the arbitrary position to hide objects such as windows, shops or private house. With the Spherical Coordinates system, powerful Privacy Zone Mask function is possible. A mask area will move with pan and tilt functions and automatically adjust in size as the lens zooms telephoto and wide.
z GLOBAL/LOCAL Image Setup
WB(White Balance) and AE(Auto Exposure) can be set up independently for each preset. There are 2 modes, "Global" mode & "Local" mode. The Global mode is that WB and/or AE are/is set up totally and simultaneously for all presets. The Global parameter setup such as WB and AE can be done in "ZOOM CAMERA SETUP" menu. The Local mode is that WB and/or AE are/is set up independently or separately for each preset. The Local parameter setup for WB and AE can be done in each preset setup menu. Each Local parameter such as WB and AE activates correspondingly when the camera arrives at each preset position. During jog operation, Global WB/AE value should be applied. All Local WB/AE values do not change although Global WB/AE value changes. The Local mode has the prior to the Global mode.
z Semi-Auto Focus This mode automatically exchanges focus modes between Manual
Focus mode and Auto Focus mode by operation. Manual Focus mode activates in preset operation and Auto Focus mode activates during jog operation. With Manual mode at presets, Focus data is memorized in each preset in advance and the camera calls focus data in correspondence with presets as soon as the camera arrives at presets. It should shorten time to get focuses. The focus mode automatically changes to Auto Focus mode when jog operation starts.
37X Speed Dome Camera 23/50
A
n
OSD Display
OPERATION 3
Preset Label
Camera ID
LABEL12345 PRESET1
I:-2- O:1 CAM 1 15/4/x1/N
P/T/Z Information
Action Title
larm Informatio
z P/T/Z Information Displays the amount of pan from zero degree vertical, the amount of
tilt from zero degree horizontal and current compass direction. Also identifies the amount of the zoom magnification.
z Camera ID Displays the selected Camera ID (Address).
z Action Title
Identfies Actions
"SET PRESET xxx" W h e n Prese t xxx i s mem orize d .
"PRESET xxx" When the c amera reaches Preset xxx .
"PATTERN x" When Pattern x is in action.
"SWG×/PRESET xxx" Wh en Sw ing x is in act i on. Displ ays both o f Sw ing
number and Preset number.
"UNDEFINED" When a undefined function is called to run
z Preset Label Displays preset labels when the camera arrives at presets.
z Alarm Information Displays activated alarms. This information shows current state of
Alarm Inputs and Relay Outputs. If an Input point is ON state, it will show a number corresponding to each point. If an Input point is OFF state, '-' will be displayed.
Example) The point 2 & 3 of inputs are ON and Output is ON, OSD will show as below.
I:-23 O:1
37X Speed Dome Camera 24/50
OSD MENU 4
Quick Programming Guide
z The menu items with < > always have sub-menus. z To go to submenus or make the cursor move to the right, press NEAR key. z To go to the previous-upper level menus, press FAR key. z To make a selection, press NEAR key z To cancel a selection, press FAR key z To move the cursor in the menu, use the joystick to the Up/Down direction or Left/Right
direction.
z To change a value of an item, use Up/Down of the joystick in the controller. z To save changes, press NEAR key.
z To can cel changes, press FA R key.
Main Menu
SPEED DOME CAMERA
-----------------------­ <SYSTEM INFORMATION> <DISPLAY SETUP> <DOME CAMERA SETUP>
<SYSTEM INITIALIZE>
z System
Information
z Display Setup Enables the user to program how labels
Displays the system information and configuration. The system setting can not be changed using the OSD menu and the information is for reference only.
are displayed on the monitor.
EXIT
z Dome Camera
Setup
z System Initialize I niti alize s all system configurations and
Enables the user to configure various functions of the camera.
all data to the factory default parameters.
37X Speed Dome Camera 25/50
DISPLAY SETUP
-----------------------­ CAMERA ID ON PTZ INFORMATION AUTO ACTION TITLE AUTO PRESET LABEL AUTO ALARM I/O AUTO <SET NORTH DIRECTION> <PRIVACY ZONE>
BACK EXIT
Display Setup
OSD MENU 4
Display setup allows you to program how labels are displayed on the monitor. In case of AUTO, the labels are displayed on the monitor when there are any changes in parameters.
z Camera ID [ON/OFF]
Displays the selected Camera ID (Address).
z PTZ Information
[ON/OFF/AUTO] Displays the amount of pan from zero
degree vertical, the amount of tilt from zero degree horizontal and current compass direction. Also identifies the amount of the zoom magnification.
z Action Title [ON/ OFF/AUTO ]
Identfies Actions. "SET PRESET xxx" "PRESET xxx" "PATTERN x" "SWG/PRESET xxx" "UNDEFINED"
z Preset Label [ON/O FF/AUTO]
Displays the preset labels when the camera arrives at presets.
z Alarm I/O [ON/OFF/AUTO]
Displays the activated alarms. This information shows the current state of Alarm Inputs and Relay Outputs. If an Input point is ON state, it will show a number corresponding to each point. If an Input point is OFF state, '-' will be displayed.
Example) The point 2 & 3 of inputs are ON and Output is ON, OSD will show as below.
I:-23 O:1
37X Speed Dome Camera 26/50
Compass Direction Setup
SET NORTH DIRECTION
------------------------
MOVE TO TARGET POSITION [NEAR:SAVE /FAR:CANCEL
Privacy Zone Mask Setup
OSD MENU 4
Move the camera to a target position and press NEAR button to save the direction as North. The direction is the ref erence direction to assign other compass directions.
PRIVACY ZONE
-----------------------­ MASK NO 1 UNDEFINED DISPLAY OFF CLEAR MASK CANCEL <EDIT MASK>
Privacy Zone Mask allows the user to program 8 rectangulars that can not be viewed by the operator of the system. To protect privacy, MAX. 8 Privacy Masks can be created on the arbitrary position to hide objects such as windows, shops or private house. With the Spherical Coordinates system, powerful Privacy Zone Mask function is possible. A mask area will move with pan and tilt functions and automatically adjust in size as the lens zooms telephoto and wide.
BACK EXIT
z Mask NO [1~8] or [1~4]
Selects a Mask number to program. If the selected mask has already data, the camera moves as it was programmed. Otherwise, “UNDEFINED” will be displayed under the Mask number.
z Display [ON/OFF]
Sets if the mask of the selected mask number shows or not on the screen.
z Clear Mask [CANCEL/OK]
Deletes the mask data of the selected mask number.
37X Speed Dome Camera 27/50
Privacy Zone Mask Area Setup
EDIT MASK 1
------------------------
MOVE TO TARGET POSITION [NEAR:SELECT/FAR:CANCEL]
Privacy Zone Mask Size Setup
EDIT MASK 1
------------------------
[ :ADJUST MASK WIDTH] [ :ADJUST MASK HEIGHT]
[NEAR:SAVE /FAR:CANCEL]
OSD MENU 4
Move your camera to an area to mask. Then a mask and the menu to adjust the mask size will be displayed.
Adjusts the mask size. Use the joystick or the arrow buttons of your controller to adjust mask size.
z  (Left/Right) Adjusts the mask width.
z  (Up/Down) Adjusts the mask height.
37X Speed Dome Camera 28/50
g
ZOOM CAMERA SETUP
-----------------------­ FOCUS MODE SEMIAUTO DIGITAL ZOOM ON IMAGE FLIP OFF SHARPNESS 16 STABILIZATION OFF <WHITE BALANCE SETUP> <AUTO EXPOSURE SETUP>
BACK EXIT
Camera Setup
OSD MENU 4
Sets the general functions of zoom camera module.
z Focus Mode [AUTO/MANUAL/SEMIAUTO]
Sets camera Focus mode. { SEMIAUTO Mode This mode automatically exchanges focus
modes between Manual Focus mode and Auto Focus mode by operation. Manual Focus mode activates in preset operation and Auto Focus mode activates during jog operation. With Manual mode at presets, Focus data is memorized in each preset in advance and the camera calls focus data in correspondence with presets as soon as camera arrives at presets. It should shorten time to get focuses. Focus mode automatically changes to Auto Focus mode when jog operation starts.
ital Zoom [ON/OFF]
z Di
Sets the digital zoom functions to ON/OFF. If this is set to OFF, the optical zoom function runs but the zoom function stops at the end of optical zoom magnification.
z Image Flip [ON/OFF]
Sets System Image Flip Function to ON/OFF. When this function is set to ON, flipped images always come out. When the camera is installed as Desktop type, set to ON to get proper images.
z Sharpness [0-32] or [0~31]
Sets image sharpness to enhance pictures.
37X Speed Dome Camera 29/50
White Balance Setup
WB SETUP - GLOBAL
-----------------------­ WB MODE AUTO RED ADJUST --­ BLUE ADJUST ---
BACK EXIT
z Stabilization [ON/OFF]
Compensates image vibrations by wind or others. The images with vibrations are compensated by Digital Zoom function and the image resolution with this function should be lower than normal image resolution when this function is turned on. Also this function may not work properly in the following cases.
Dark scene or Low contrast scene High frequency vibration During Pan/Tilt/Zoom/Focus moving During Iris/Shutter/Gain moving
z WB Mode [AUTO/MANUAL]
Retains color balance over a color temperature range. In auto mode, this feature automatically processes the viewed image. In Manual mode, Red and Blue level can be set up manually.
z Red Adjust [0-255] or [10~60]
Adjusts the picture output in the red range.
z Blue Adjust [0-255] or [10~60]
Adjusts the picture output in the blue range.
OSD MENU 4
37X Speed Dome Camera 30/50
Auto Exposure Setup
AE SETUP - GLOBAL
-----------------------­ BACKLIGHT OFF DAY/NIGHT AUTO BRIGHTNESS 50 IRIS AUTO SHUTTER ESC AGC MIDDLE SSNR MIDDLE SENS-UP <AUTO> BACK EXIT
OSD MENU 4
z Backlight [OFF/WDR/BLC/HLC] or [OFF/BLC/HLC]
or [ON/OFF] Sets Backlight Compensation. If a bright
backlight is present, the subjects in the picture may appear dark or as a silhouette. Backlight compensation enhances objects in the center of the picture. The camera uses the center of the
z Day/Night [AUTO/DAY/NIGHT] or
z Brightness [0~100]
picture to adjust the iris. If there is a bright light source outside of this area, it will wash out to white. The camera will adjust the iris so that the object in the sensitive area is properly exposed.
Some modles has WDR(Wide Dynamic Range) function, which are better function than BLC. HLC(High Light Compensation) function removes the high light in a limited environment such as parking garage.
[AUTO1/AUTO2/DAY/NIGHT] Sets Day&Night mode. There are 2 AUTO modes in ×10 model # AUTO1 Mode : The sensitivity to change
a mode is fixed. # AUTO2 Mode : The sensitivity to change
Night mode to Day mode is adjustable. The sensitivity range is 1~255. The higher numeric value is selected, the lower illumination Night mode changes to Day mode at. If this is set to AUTO2 mode, ACG is fixed to HIGH.
Adjusts the brightness of the images. Iris, The Shutter Speed and Gain are adjusted automatically in correspondence with each numeric value.
37X Speed Dome Camera 31/50
OSD MENU 4
z IRIS [AUTO/MANUAL(F1.6~F28)] or
[AUTO/MANUAL(0~100)] Sets Iris to operate automatically or at a user-
defined level. If Iris is set to Auto, Iris has higher priority in adjusting AE and Shutter Speed is fixed. Auto iris is the lens function that automatically opens closes the iris in response to changing light conditions.
If Iris is set to Manual, Iris is fixed and Iris has lower priority in adjusting AE, in comparison with others.
z Shutter Speed [ESC/A.Flicker/Manual(256X~1/120000 sec)] or
[ESC/A.Flicker/Manual(128X~1/120000 sec Sets Shutter Speed. Shutter Speed is the duration
of the electronic shutter. If Iris is set to Manual and Shutter Speed is set to ESC, Shutter Speed has higher priority. If Shutter Speed is set to A.Flicker, to remove Flicker, Shutter Speed should be set to 1/100 sec. for NTSC and 1/120 for PAL.
z AGC [OFF/LOW/MIDDLE/HIGH/MANUAL(5~41dB)]
or [OFF/NORMAL/HIGH] Sets AGC. This setting enhances image
brightness automatically in case that luminance level of image signal is too low.
z SSNR [OFF/LOW/MIDDLE/HIGH]
Sets SSNR. This setting enhances the images by deducting noises when the gain level of the mages is too high.
z SENS-UP [AUTO(2~256)/OFF] or [AUTO(2~128)/OFF]
Sets SENS-UP. This setting activates Slow Shutter function when luminance of image (signal) is too dark.
It is possible to set up the maximum number of frames piled up one on another by Slow Shutter function.
37X Speed Dome Camera 32/50
sources
WDR (Wide Dynamic Range) Setup
WDR
-----------------------­ LIMIT MIDDLE LEVEL 50
BACK EXIT
HLC (High Light Compensation) Setup
HLC
-----------------------­ LIMIT LOW COLOR 5
BACK EXIT
z Limit [AUTO/MANUAL]
z Color [0~10]
OSD MENU 4
z Limit [LOW/MIDDLE/HIGH]
z Level [0~100]
When there are too bright lights, this function blocks light sources on images to have better images. For example, when there is a car coming to a camera at night, this function blocks car headlights to recognize its number plate.
Assigns colors of masks to block light
37X Speed Dome Camera 33/50
MOTION SETUP
-----------------------­ MOTION LOCK OFF PWR UP ACTION ON AUTO FLIP ON JOG MAX SPEED 120/SEC JOG DIRECTION INVERSE FRZ IN PRESET OFF <PARKING ACTION SETUP> <ALARM INPUT SETUP> BACK EXIT
Motion Setup
OSD MENU 4
Sets the general functions of Pan/Tilt motions.
z Motion
Lock
z Power Up
Action
z Auto Flip [ON/OFF]
z Jog Max
Speed
z Jog
Direction
z Freeze
in Preset
[ON/OFF] If Motion Lock is set to ON, it is impossible to
set up and delete Preset, Swing, Pattern and Group. It is possible only to run those functions. To set up and delete those functions, enter into OSD menu.
[ON/OFF] Refer to Other Functions" section.
Refer to Other Functions" section.
[1°/sec ~360°/sec] Sets the maximum jog speed. Jog speed is
inversely proportional to the zoom magnifications. As the zoom magnification goes up, the pan/tilt speed goes down.
[INVERSE/NORMAL] Sets the Jog Direction. If this is set to
Inverse, the view direction in the screen is same as the direction of joystick. If this is set to Normal, the view direction in the screen is the reverse dirction of joystick.
[ON/OFF] Sets Frame Freeze Function. This feature
freezes the scene on the monitor when going to a preset. At the start point of a preset movement, a camera starts freezing the image of the start point. Camera keeps displaying the image of the start point during preset movement and does not display the images which camera gets during preset movement. As soon as camera stops at preset end point, camera starts displaying live images which it gets at the end preset point. This feature also reduces bandwidth when working with digital systems or digital network systems.
This function availability should be different by models.
37X Speed Dome Camera 34/50
Parking Action Setup
PARKING ACTION SETUP
-----------------------­ PARK ENABLE OFF WAIT TIME 00:10:00 PARK ACTION HOME
BACK EXIT
OSD MENU 4
This feature allows the camera to begin a specified action after a programmed time of inactivity.
z Park Enable
z Wait Time [1~59 sec. / 1~180 min.]
z Park Action [HOME/PRESET/PATTERN/SWING/GROU
[ON/OFF] If Park Enable is set to ON, the camera
runs an assigned function automatically if there is no PTZ command during the programmed "Wait Time".
Wait Time can be programmed from 1 second to 180 minutes.
P/PREV ACTION] This feature defines the activity when the
camera parks. If Park Action is set to HOME, the camera moves to the home position which is memorized when the system boots. If Park Action is set to PREV. ACTION, the camera runs the previous action which it ran most recently.
37X Speed Dome Camera 35/50
Alarm Input Setup
ALARM INPUT SETUP
-----------------------­ ALARM NO. 1
TYPE N.OPEN ACTION NOT USED HOLD TIME ENDLESS POST ACTION HOME
BACK EXIT
OSD MENU 4
Defines Alarm Function. When an alarm is receive, an input signal to the camera triggers the user-defined action programmed for the alarm.
z Alarm No [1~3]
Selects a sensor number to set up.
z Type [Normal OPEN/Normal CLOSE]
Selects sensor operation type.
z Action [NOT
z Hold Time [ENDLESS / 1~59 SEC. / 1~180 MIN.]
z Post Action
USED/PRESET/PATTERN/SWING/GROUP] Selects an action to run when a sensor
signal is input.
Sets the time period for the action which is run by external sensor activation. After the time period passes, the action pre-defined in Post Action runs sequentially in succession to the action by external sensor activation. If this option is set to ENDLESS, Post Action does not activate.
[HOME/PRESET/PATTERN/SWING/GROUP /PREV ACTION]
Selects the action that a camera will run after the time period inHOLD TIME passes. If Post Action is set to “PREV. ACTION, the camera runs the previous action which it ran most recently.
37X Speed Dome Camera 36/50
Preset Setup
PRESET SETUP
-----------------------­ PRESET NO. 1
CLR PRESET CANCEL <EDIT SCENE> <EDIT LABEL> LABEL123 RELAY OUT OFF CAM ADJUST GLOBAL
BACK EXIT
z Preset
Number
[1~128] Selects a preset number to set up. If a
selected preset is already defined, the camera moves to the pre-defined position and preset parameters such as Label and CAM Adjust show on the monitor. If a selected preset is not defined, “UNDEFINED” shows on the monitor.
z Clear
Preset
z Edit
Preset Scene
z Edit
Preset Label
[CANCEL/OK] Deletes the data of the selected Preset.
Re-defines the scene position of the selected Preset.
Edits the label of the selected Preset to show on the monitor when the preset runs. MAX. 10 alphanuberic characteristics are allowed.
z Relay Out Defines the relay output.
z CAM Adjust [GLOBAL/LOCAL]
WB(White Balance) and AE(Auto Exposure) can be set up independently for each preset. There are 2 modes, "Global" mode & "Local" mode. The Global mode is that WB and/or AE are/is set up totally and simultaneously for all presets. The Global parameter setup such as WB and AE can be done in "ZOOM CAMERA SETUP" menu. The Local mode is that WB and/or AE are/is set up independently or separately for each preset. The Local parameter setup for WB and AE can be done in each preset setup menu. Each Local parameter such as WB and AE activates correspondingly when the camera arrives at each preset position. During jog operation, Global WB/AE value should be applied. All Local WB/AE values do not change although Global WB/AE value changes. The Local mode has the prior to the Global mode.
OSD MENU 4
37X Speed Dome Camera 37/50
Preset Scene Setup
OSD MENU 4
EDIT SCENE - PRESET 1
------------------------
MOVE TO TARGET POSITION [NEAR:SAVE /FAR:CANCEL]
Preset Label Setup
EDIT LABEL - PRESET 1
-----------------------­ [ ]
---------­ 1234567890 OK ABCDEFGHIJ CANCEL KLMNOPQRST UVWXYZabcd efghijklmn opqrstuvwx yz<>-/:.
----------
○1 Use the Joystick to move the camera to a desired
position.
○2 Save the preset position by pressing NEAR key.
○3 Press FAR key to cancel targeting the preset position.
Edit the label of the selected preset to show on the monitor when camera arrives at the preset. In the Edit Label menu, the dark rectangular is the cursor. As soon as finishing selecting an alphabet or a number, the cursor moves to the next digit.
[ ]
Current Cursor Position
With Left/Right/Up/Down of the joystick, move to a
desired Alphabet or a desired number in the Alphanumeric set. To select a desired Alphabet or a desired number, press the NEAR key.
---------­1234567890 ABCDEFGHIJ KLMNOPQRST UVWXYZabcd efghijklmn opqrstuvwx yz<>-/:.
----------
Back Space Char.Space Char.
If you want to use a blank, select the double quotation mark (" "). If you want to delete an Alphabet or a number, use the back space character (" ←").
If you complete the Label editing, move the cursor to
"OK" and press the NEAR key to save the completed label. To abort the current change, move the cursor to "Cancel" and press the NEAR key.
37X Speed Dome Camera 38/50
SWING SETUP
-----------------------­ SWING NO. 1 1ST POS. NOT USED 2ND POS. NOT USED
SWING SPEED 30/SEC CLEAR SWING CANCEL RUN SWING
BACK EXIT
Swing Setup
OSD MENU 4
z Swing
Number
z 1st Position 2nd Position
z Swing
Speed
z Clear Swing [CANCEL/OK]
z Run Swing Runs Swing for the test purposes to check
[1~8] Selects a Swing number to edit. If the
selected Swing is not defined, "NOT USED" is displayed in the 1st Position and the 2nd Position.
[PRESET 1~128] Sets the 2 positions for a Swing function. If
the selected preset is not defined, "UNDEFINED" is displayed as shown below.
SWING SETUP
-----------------------­ SWING NO. 1 1ST POS. PRESET5 2ND POS. NOT USED UNDEFINED
When a swing function runs, the camera moves from the preset assigned as the 1st point to the preset assigned as the 2nd point in CW(Clockwise) direction. Then the camera moves from the preset assigned as the 2nd point to the preset assigned as the 1st point in CCW (Counterclockwise) direction. In case that the preset assigned as the 1st point and the preset assigned as the 2nd point are same or only 1 Preset position is assigned, the camera turns on its axis by 360° in CW direction and then it turns on its axis by 360° in CCW direction.
[1°/sec. ~180°/sec.] Defines Swing speed between the 2 Preset
positions from 1°/sec to 180°/sec
Deletes the data of the selected Swing.
if it works properly.
37X Speed Dome Camera 39/50
W
Pattern Setup
PATTERN SETUP
-----------------------­ PATTERN NO. 1 UNDEFINED CLR PATTERN CANCEL RUN PATTERN <EDIT PATTERN>
BACK EXIT
Pattern Edit
EDIT PATTERN 1
------------------------
MOVE TO START POSITION [NEAR:START /FAR:CANCEL]
EDIT PATTERN 1
[NEAR:SAVE /FAR:DELETE] 0/0/x1/N
OSD MENU 4
z Pattern Number [1~4 ]
Selects a Pattern number to edit. If the selected pattern number is not defined, "UNDEFINED" will be displayed under the selected pattern number.
z Clear Pattern [CA NCEL /OK]
Deletes the data of the selected pattern.
z Run Pattern Runs the Pattern for the test purposes to
z Edit Pattern Edits the selected pattern.
ith the Joystick of your controller, move the camera to the start position with an appropriate zoom magnafication. To start the pattern recording, press NEAR key. To exit, press FAR key.
Move camera with joystick of controller or run preset
function to memorize the path (mostly curve path) in the selected pattern. The movement by Joystick and preset movement will be memorized in a pattern. After a pattern is programmed, the remaining storage is displayed in progress bar on the screen.
To save the data and exit, press NEAR key. To cancel
saving the data and delete the data, press FAR key.
check if it works properly.
37X Speed Dome Camera 40/50
Group Setup
GROUP SETUP
-----------------------­ GROUP NO. 1 UNDEFINED CLEAR GROUP CANCEL RUN GROUP <EDIT GROUP>
BACK EXIT
Group Edit
EDIT GROUP 1
-----------------------­ NO ACTION ### DWELL OPT
-----------------------­ 1 NONE 2 NONE 3 NONE 4 NONE 5 NONE
-----------------------­ SAVE CANCEL [NEAR:EDIT]
EDIT GROUP 1
-----------------------­ NO ACTION ### DWELL OPT
-----------------------­ 1 NONE 2 NONE 3 NONE 4 NONE 5 NONE
-----------------------­ SAVE [NEAR:EDIT ACT] CANCEL [FAR :EDIT END]
OSD MENU 4
z Group Number [1~ 8]
Selects a Group number to edit. If the selected Group number is not
defined, "UNDEFINED" will be displayed under the selected Group number.
z Clear Group [CANCEL/OK]
Deletes the data of the selected Group.
z Run Group Runs the Group for the test purposes to
check if it works properly.
z Edit Group Edit the selected Group.
Press Near key when the cursor is at “NO” to start editing the selected Group.
Note that MAX. 20 actions are allowed in a Group. Move
the cursor up/down to select an Action. Press Near key to edit.
37X Speed Dome Camera 41/50
EDIT GROUP 1
-----------------------­ NO ACTION ### DWELL OPT
-----------------------­ 1 NONE 2 NONE 3 NONE 4 NONE 5 NONE
-----------------------­ SAVE [ :MOVE CURSOR] CANCEL [ :CHANGE VAL.]
EDIT GROUP 1
-----------------------­ NO ACTION ### DWELL OPT
-----------------------­ 1 PRESET 1 00:03 360 2 NONE 3 NONE 4 NONE 5 NONE
-----------------------­ SAVE [ :MOVE CURSOR] CANCEL [ :CHANGE VAL.]
EDIT GROUP 1
-----------------------­ NO ACTION ### DWELL OPT
-----------------------­ 1 PRESET 1 00:03 360 2 NONE 3 NONE 4 NONE 5 NONE
-----------------------­ SAVE [NEAR:EDIT ACT] CANCEL [FAR :EDIT END]
OSD MENU 4
Define Action, Dwell time and Option. Note that the dark rectangular is the cursor. Move the cursor Left/Right to select an item and move cursor Up/Down to change each parameter.
z Action ### [NONE/PRESET/SWING/PATTERN]
z DWELL [0 SEC. ~ 4 MIN.]
Sets the Dwell Time between functions.
z OPT Option. It is a preset speed when a
preset is selected in the Action. It is the number of repeat when a Pattern or a Swing is selected in the Action.
Edit the items such as Action, ###, Dwell and OPT by moving the cursor.
After finishing editing a Action, press Near key to go to
the previous-upper level menu (Step ). Move the cursor Up/Down to select an Action number and repeat Step ~ Step to keep editing the selected Group.
37X Speed Dome Camera 42/50
A
EDIT GROUP 1
-----------------------­ NO ACTION ### DWELL OPT
-----------------------­ 1 PRESET 1 00:03 360 2 NONE 3 NONE 4 NONE 5 NONE
-----------------------­ SAVE CANCEL
OSD MENU 4
fter finishing setting up, press FAR key to exit. Then the
cursor will move to “SAVE”. Press Near key to save the data.
37X Speed Dome Camera 43/50
System Initialization
OSD MENU 4
SYSTEM INITIALIZE
-----------------------­ CLEAR ALL DATA NO CLR DISPLAY SET NO CLR CAMERA SET NO CLR MOTION SET NO CLR EDIT DATA NO REBOOT CAMERA NO REBOOT SYSTEM NO
BACK EXIT
z Clear All Data Deletes all configuration data and the system
is set to the factory default.
z Clear Display Set Initializes all the configuration data for Display. z Clear Camera Set
Initializes all the configuration data for Camera.
z Clear Motion Set Initializes all the configuration data for Motion. z Clear Edit Data Deletes all the configuration data for Preset,
Swing, Pattern and Group.
z Reboot Camera Reboots the zoom camera module. z Reboot System Reboots the system.
Factory Default
z Display Parameters z Camera Parameters
Camera ID ON Focus Mode SemiAuto PTZ Information AUTO Digital Zoom ON Action Title AUTO Image Flip OFF Preset Label AUTO Sharpness 16 Alarm I/O AUTO Stabilization OFF North Direction Pan 0° White Balance AUTO Privacy Zone Undefined Backlight OFF Day&Night AUTO ro AUTO2 Brightness 50 or 25 Iris AUTO Shutter ESC z Motion Parameters AGC MIDDLE or HIGH Motion Lock OFF SSNR MIDDLE Power Up Action ON SENS-UP AUTO Auto Flip ON Jog Max Speed 120°/sec z User-Defined Data Jog Direction INVERSE Preset 1~128 Undefined Freeze In Preset OFF Swing 1~8 Undefined Park Action OFF Pattern 1~4 Undefined Alarm Action OFF Group 1~8 Undefined
37X Speed Dome Camera 44/50
Specifications
HTSD37X / SIPSD37X
Video Signal Format NT SC
Image Sensor Sony 1/4'' Double Density Interline Transfer CCD
Total Pixels 811(H)×508(V) 410K
Effective Pixels 768( H) ×494(V) 380K
Horizontal Resolution 550 TV Line s(Co l or), 6 80 TV Li nes( B/W)
Video Signal-to-Noise 50 d B (AGC Of f )
Zoom 37X Opti cal Z oom, ×12 Digital Zoom
Forcal Length F1.6~3.9, f=3.5~129.5mm
Angle of View H : 55.5°(Wide)~1.59°(Tele) / V : 42.5°(Wide)~1.19°(Tele)
Zoom Speed 2.5 sec (Wide to Tele)
Minimum Illuminance 0.7 Lux (Color) / 0. 06 Lux (B/W), 50 IRE / F1.6
Day & Night Au t o / Day / N ight (ICR )
Focus Auto / Manual / SemiAuto
Iris Aut o / Manu a l
Shutter Speed 256X ~ 1/120000 sec
AGC Low / Middle / High / Manual / Off
White Balance Auto / Manual(Red, Blue Gain Adjustable. 1800°K~10500°K)
BLC WDR / BLC / HLC / Off
Flickerless Selectable
SSNR Low / Middle / High / Off
Privacy Zone 8 Ma sks, Sphe r ical Coordin ate
Stabilization ON / O FF
SPECIFICATIONS 5
37X Speed Dome Camera 45/50
MECHANISM PART
Movement Range
Speed
Preset 127 Presets (Label, Independent Camera Parameter Setting)
Pattern 4 Patterns [1200 Commands(Approx. 5 Minute) / Pattern]
Swing 8 Swings
Group
Other Pan/Tilt Functions Auto Flip, Auto Parking, Power Up Action and etc.
Communication RS-485 (HTSD37X ONLY)
Protocol Pelco-D, Pelco-P Selectable
OSD English, Menu / PTZ information etc
Sensor Input 3 Inputs, Photo-Coupler Type, DC 5V~12V
Alarm Outputs 1 Output, Relay Output, MAX. Load DC24V 1A / AC125V 0.5A
Fan Always ON
Heater Operation Start from Internal Temperature 10°C
Operating Temperature -22°F ~ +122°F
Pan 360°(Endless)
Tilt 90°
Preset 360°/sec.
Jog 0.05 ~ 360°/sec. (Proportional to Zoom)
Swing 1~ 180°/sec.
8 Groups (MAX. 20 Actions with The Combination of Preset,
Pattern and Swing)
SPECIFICATIONS 5
37X Speed Dome Camera 46/50
MECHANICAL
Ceiling Mount Wall Mount
Dome Polycarbonate
Material
EBO/EBI model
[Note]
1) Specification and features are subject to change without prior notice.
2) Check the voltage and current capacity of rated power carefully.
Internal Polycarbonate, ABS
External Aluminium
Dome Size
Dimension
Weight Approx 3.2 Kg Approx 3.8 Kg
192×265.3 mm 296×276.6 mm
150mm / ∅ 5.9”
SPECIFICATIONS 5
HTSD37X : 24VAC ONLY SIPSD37X : 12VDC ONLY
37X Speed Dome Camera 47/50
z Main Body
z Wall Mount Type
Dimension
144
277.9
155
SPECIFICATIONS 5
10
7. 5
118.6 80
84-
100
138.6
229.8
[Unit mm]
37X Speed Dome Camera 48/50
WARRANTY 6
37X Speed Dome Camera 49/50
200 New Hightway
Amityville, NY 11701
631-957-8700
Rev.03082010
Speco Technologies is constantly developing product improvements.
We reserve the right to modify product design and specifications without notice
and without incurring any obligation.
37X Speed Dome Camera 50/50
Rev.100308
Loading...