Speco Technologies O8VLD1 User Manual

Quick Start Guide
8MP IP Vandal Dome Camera
O8VLD1
Version 1.0
Welcome
Thank you for purchasing this network camera!
This owner’s manual is designed to be a reference tool for your system.
Please read this manual carefully before operating the unit and retain it for future reference.
Should you require any technical assistance, please contact Speco Technologies Technical Support.
ii
Important Safeguards and Warnings
1Electrical safety
All installation and operation here should conform to local electrical safety codes.
Use a certified/listed 12VDC Class 2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same time; it may result in
device damage! The product must be grounded to reduce the risk of electric shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2Environment
Heavy stress, violent vibration or exposure to water is not allowed during transportation, storage and
installation.
This product should be installed in a cool, dry place away from direct sunlight and heat sources.
Do not install the product in extreme temperature conditions.
Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS sensor failure.
Do not block any ventilation openings.
Do not allow water and liquid intrusion into the camera.
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth dampened with a small
quantity of neutral detergent. Finally use the dry cloth to clean the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure cleaning (such as
using cloth) may result in poor IR functionality and/or IR reflection.
The grounding holes of the product are recommended to be grounded to further enhance the reliability of the
camera.
Dome cover is an optical device, please don’t touch or wipe cover surface directly during installation and use,
please refer to the following methods if dirt is found:
Stained with dirt
Use oil-free soft brush or hair dryer to remove it gently.
Stained with grease or fingerprint
Use oil-free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens center outward.
Change the cloth and wipe several times if it is not clean enough.
Warning
This camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.
iii
Statement
Accessory Name
Amount
Network Camera Unit
1
Quick Start Guide
1
Installation Accessories Bag
1 CD
1
This guide is for reference only.
Product, manuals and specifications may be modified without prior notice. Speco Technologies reserves the
right to modify these without notice and without incurring any obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Note:
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is broken or missing in the
package.
iv
Table of Contents
1 Physical Specifications ................................................................................................................. 1
1.1 Components .................................................................................................................... 1
1.2 Dimensions ...................................................................................................................... 2
2 Device Installation ........................................................................................................................ 3
2.1 Installation Steps ............................................................................................................. 3
3 IP Scanner ..................................................................................................................................... 5
3.1 Overview ......................................................................................................................... 5
3.2 Operation ........................................................................................................................ 5
4 Web Operation ............................................................................................................................. 6
4.1 Login and Main Interface ................................................................................................ 6
1
Component
Component Name
Component 1
Dome module
Component 2
Dome enclosure
Port
Port Name
Note
Port 3
Ethernet port
Network data in/out and PoE Port 4
DC power jack
Connect to DC 12V power, input power
1 Physical Specifications
1.1 Components
Note:
The following figure is for reference only, which is used to indicate the components and the functions.
Refer to the following figure for component structure. See Figure 1-1.
Figure 1-1 Component structure
Please refer to the following sheet for detailed information.
2
1.2 Dimensions
Please refer to the following figure for dimension information. The unit is in mm. See Figure1-2.
Figure1-2
3
2 Device Installation
2.1 Installation Steps
Note:
Before installation, please make sure the installation surface can support a minimum of 3 times the weight
of the camera
Figure 2-1 Device installation illustration
Step 1
Use inner hex wrench in the accessories bag to open dome enclosure by unfastening three inner hex screws on
enclosure.
Step 2
Put installation template on the designated surface where you will install the device (wall or ceiling).
Step 3
Drill holes according to position of the holes on the installation template and then insert the expansion bolts in
the holes. Secure these three bolts firmly.
Note:
If user pulls out cable from top of installation surface, you must dig an exit hole on installation surface
according to the installation template.
If user pulls out cable from side of cable channel, it must go through the U-shape channel on dome
pedestal, and take out cable from the side exit hole on pedestal.
Step 4
Adjust the device installation pedestal to the proper position and then pull cable through the exit hole on
Installation surface. Make direction of TOP sign same as it is on the installation template. Line up the three
screw holes in the device pedestal to the three plastic expansion bolt holes in the installation position. Put the
three self-tapping screws in the three plastic expansion bolts firmly. Fix dome body on installation surface.
Step 5
Hold both sides of the rotation bracket bottom with hands, rotate horizontally along the axis, and adjust lens
horizontal direction to designated position. Hold the LED decoration cover with hand, rotate along the vertical
4
direction, adjust the lens vertical direction to designated position; it is okay to loosen the fix screws on both
sides of the bracket first if it is too tight to adjust (just make it loose, do not take it out), then adjust the lens,
tighten the fix screws after adjustment. Hold the LED decoration cover with hands, rotate horizontally along the axis, and adjust the lens image to designated position. Range of lens: vertical (0°+64°), horizontal (0°+355°), image rotation direction (0°+355°).
Note:
When tilted to 64° vertically, please make sure to set the image rotation correctly in order to avoid the outer
cover blocking the IR light which would result in IR reflection.
Figure 2-2
Note:
Long press the “Reset button” shown in Figure 2-2 for 10 seconds when the device is powered on if the
device needs to be restored to the factory default setting.
Step 6
Take up the dome enclosure, put it back on the camera properly regarding to screw and hole, and fasten the
three inner hex screws with wrench.
5
3 IP Scanner
3.1 Overview
IP Scanner can search for the device on the local network.
Please note that only devices that are on the same subnet can be discovered.
3.2 Operation
Open up IP Scanner.
Error! Reference source not found.
In the device list, you can view the IP address, model number, and MAC address of each device. Select the
applicable device and double click to open up the web viewer.
Figure 3-1 IP Scanner
6
Input your IP address here
4 Web Operation
This device supports viewing and management via a web browser on a PC.
4.1 Login and Main Interface
Open the browser and input network camera address in the address bar or double click the device in IP Scanner.
See Figure 4- 1.
Figure 4- 1 IP address
The login interface is shown as below. See Figure 4- 2.
Please input your user name and password.
Default user name is admin and password is 1234.
Note: For security purposes, please change the password after initial login.
Figure 4- 2 Web login
After logging in, follow directions to install applicable plugins.
Loading...