i
Quick Start Guide
Full HD IP Bullet Camera
O3VLB3
Version 1.0
ii
Welcome
Thank you for purchasing this network camera!
This owner’s manual is designed to be a reference tool for your system.
Please read this manual carefully before operating the unit and retain it for future reference.
Should you require any technical assistance, please contact Speco Technologies Technical Support.
iii
Important Safeguards and Warnings
1
．．．．
Electrical safety
All installation and operation here should conform to local electrical safety codes.
Use a certified/listed 12VDC Class 2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same time; it may result in
device damage! The product must be grounded to reduce the risk of electric shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2
．．．．
Environment
Heavy stress, violent vibration or exposure to water is not allowed during transportation, storage and
installation.
This product should be installed in a cool, dry place away from direct sunlight and heat sources.
Do not install the product in extreme temperature conditions.
Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS sensor failure.
Do not block any ventilation openings.
Do not allow water and liquid intrusion into the camera.
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth dampened with a small
quantity of neutral detergent. Finally use the dry cloth to clean the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure cleaning (such as
using cloth) may result in poor IR functionality and/or IR reflection.
The grounding holes of the product are recommended to be grounded to further enhance the reliability of the
camera.
Dome cover is an optical device, please don’t touch or wipe cover surface directly during installation and use,
please refer to the following methods if dirt is found:
Stained with dirt
Use oil-free soft brush or hair dryer to remove it gently.
Stained with grease or fingerprint
Use oil-free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens center outward.
Change the cloth and wipe several times if it is not clean enough.
Warning
This camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.
iv
Statement
This guide is for reference only.
Product, manuals and specifications may be modified without prior notice. Speco Technologies reserves the
right to modify these without notice and without incurring any obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Note:
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is broken or missing in the
package.
Accessory Name Amount
Network Camera Unit 1
Quick Start Guide 1
Installation Accessories Bag 1
CD 1
v
Table of Contents
1 Physical Specifications .............................................................................................................. 1
1.1
Device External Cable ................................................................................................. 1
1.2
Dimensions ................................................................................................................. 1
2 Device Installation .................................................................................................................... 2
2.1
Installation Steps ........................................................................................................ 2
3 IP Scanner ................................................................................................................................ 4
3.1
Operation ................................................................................................................... 4
4 Web Operation......................................................................................................................... 5
4.1
Login and Main Interface ............................................................................................ 5
1
1 Physical Specifications
1.1 Device External Cable
You can refer to the following figure for cable information. See Figure 1-1.
Figure 1-1 Cable
Please refer to the following sheet for detailed information.
No. Port name Function description
1
2 DC power jack Connect to DC 12V power
Ethernet port Network data in/out and PoE
1.2 Dimensions
Please refer to the following figure for dimension information. The unit is in mm. See Figure1-2.
Figure 1-2
2
2 Device Installation
Note:
Before installation, please make sure the installation surface can support a minimum of 3 times the
weight of the camera
2.1 Installation Steps
Figure 2-1 Device installation 1
Please see Figure 2-1 and Figure 2-2
Step 1
Dig holes on the installation surface (wall or ceiling).
Step 2
Take out the expansion bolts from the accessories bag and insert them into the holes.
Step 3
Take out the installation screws. Tighten the screws to fix the device on the surface. Adjust the sunshield
and tighten the screw.
Step 4
Plug external wiring of the device properly.
3
Figure 2-2 Device installation 2
Step 5
Use the screwdriver (in accessories bag) to loosen adjusting screw.
Step 6
Adjust the device in all possible directions, and set its monitoring direction according to the requirements.
Step 7
Use the screwdriver to tighten the adjusting screws.
3 IP Scanner
IP Scanner can search for the device on the local network.
Please note that only devices that are
Error! Reference source not found.
In the device list, you can view the IP address, model number, and MA
the applicable device and double click to open up the web viewer.
C address of each device. Select
3.1 Operation
Open up IP Scanner.
on the same subnet can be discovered.
Figure 3-1
4 Web Operation
This device supports viewing and management via a web browser on a PC.
Login and Main Interface
Open the browser and input network camera address in the address bar or double click the device in IP
The login interface is shown as below. See
Please input your user name and password.
and password is
Note: For security purposes, please change the password after initial login.
After logging in, follow directions to install applicable plugins.
add
ress here
4.1
Scanner. See Figure 4- 1.
Input your IP
Default user name is
admin
Figure 4- 1 IP address
Figure 4- 2.
1234
.
Figure 4- 2 Web login
Loading...