Speco Technologies IP-INTT5 User Manual

IP Camera User’s Manual Speco Technologies

IP Camera User’s Manual

(Version 1.3.2)

IP-INTB1 & IP-INTB2 & IP-WDRB1

Network Bullet Cameras

IP-INTD3 & IP-INTD4

Network Dome Cameras

IP-INTT5 & IP-T5

Network Traditional Cameras

IP-SD10X

Speed Dome Camera

IP Camera User’s Manual Speco Technologies

Introduction

We appreciate your purchasing our IP Network Camera.

This is a Network Camera with a built-in MPEG-4 CODEC and Streaming Server.

It uses an MPEG-4 CODEC as the Video Compression method and has a built-in Streaming Server

which allows you to monitor and record real time images in remote places over the Internet.

Our IP cameras support both Static IP and Dynamic IP addresses and can change their

Communication Ports, allowing several Network Cameras to be installed on one IP. Our IP

cameras also permits you:

 To record an Event in your own FTP server installed in a remote location.

 To search / delete / down-load / replay the recorded video.

 Support various wireless devices such as Mobile Phone, PDA to see real time Video in

Wireless Internet handset.

For more information or inquiry, please contact us to ;

Home Page : www.specotech.com

Telephone : 631-957-8700

Fax : 631-957-9142

Address : 200 New Highway, Amityville, NY 11701

Appearance, function and specification may be changed without prior notification. Our company

assumes no responsibility for visible or invisible loss resulted from changes in policy or products.

IP Camera User’s Manual Speco Technologies

Important Notes

 The Network Camera may be damaged by electrical and physical shock

 Do not try to disassemble the products. Contact or consult the distributor or

Head Office for after sale service. There may be no Quality Assurance for the

products disassembled arbitrarily.

 Do not use these products to be connected with life related device like

medical apparatus.

 Do not touch the front lens of the camera. It is one of the most important

parts of the camera.

 Never allow the camera face to strong light directly. It can damage the CCD.

IP Camera User’s Manual Speco Technologies

Contents

1. FEATURE............................................................................ 8

1.1. PACKAGE ............................................................................................................ 8

1.2. DIMENSION AND CAMERA FEATURES ................................................................... 9

1.2.1. Dimensions ..................... ............ ........... ........... ........... ............ ........... ........... ............ ........... ....... 9

1.2.2. Camera Feature..... ........... ........... ............ ........... ........... ........... ............ ........... ........... ............ ... 11

2. INSTALL AND CHECK VIDEO................................................ 14

2.1. INSTALLATION.................................................................................................... 14

2.2. VIDEO CHECK ................................................................................................... 14

3. BASIC SETTING ................................................................. 19

3.1. CHECK NETWORK AND INSTALLATION TYPE ...................................................... 19

3.2. INSTALLATION WITHOUT IP SHARING DEVICE (ROUTER)..................................... 20

3.2.1. Static IP Setup. ........... ........... ............ ........... ........... ............ ........... ........... ........... ............ ......... 20

3.2.2. Dynamic IP Setup ...................... ............ ........... ........... ........... ............ ........... ........... ............ .... 23

3.3. INSTALLATION WITH IP SHARING DEVICE (ROUTER).......................................... 25

3.4. CAUTIONS ......................................................................................................... 29

4. EXPERT SETTING............................................................... 31

4.1. GENERAL SETTING ............................................................................................ 33

4.1.1. Title Setting .. ............ ........... ........... ........... ............ ........... ........... ............ ........... ........... ............ . 33

4.1.2. Administrator’s ID and Password Change.... ........... ........... ........... ............ ........... ........... .... 34

4.1.3. User Registration .................... ........... ........... ............ ........... ........... ............ ........... ........... ........ 34

4.1.4. User List and Delete........... ........... ........... ............ ........... ........... ............ ........... ........... ........... . 35

4.1.5. Skip Login (Automatic Monitoring) ..... ............ ........... ........... ........... ............ ........... ........... . 35

4.1.6. Time Zone Setting ..................... ........... ........... ............ ........... ........... ............ ........... ........... ..... 36

4.1.7. Set Download Route of Plug-in Type ActiveX.... ........... ........... ........... ............ ........... ........ 36

4.1.8. Select Language .......... ........... ............ ........... ........... ............ ........... ........... ............ ........... ....... 37

IP Camera User’s Manual Speco Technologies

4.2. NETWORK SETTING ........................................................................................... 37

4.3. VIDEO SETTING ................................................................................................. 38

4.3.1. Video Setting ................... ........... ............ ........... ........... ........... ............ ........... ........... ............ .... 38

4.4. COLOR SETTING ............................................................................................... 39

4.5. ALARM SETTING ................................................................................................ 39

4.5.1. Alarm Event Setting .. ........... ............ ........... ........... ........... ............ ........... ........... ............ .......... 39

4.5.2. Alarm Event Test ..... ............ ........... ........... ........... ............ ........... ........... ............ ........... ........... . 41

4.6. DIO SETTING (SUPPORT FOR IP-INTT5/T5, IP-SD10X).............................. 41

4.7. MOTION AREA SETUP........................................................................................ 42

4.8. CAMERA SETTING(SUPPORT FOR IP-SD10X).................................................. 43

4.9. HOMEPAGE UPDATE.......................................................................................... 44

4.10. FIRMWARE UPDATE ........................................................................................... 44

4.10.1. Remote Upgrade ... ........... ........... ........... ............ ........... ........... ............ ........... ........... ........... .... 45

4.10.2. System Re-booting ........ ........... ............ ........... ........... ........... ............ ........... ........... ............ .... 47

4.11. FACTORY RESET ............................................................................................... 48

4.11.1. Reset Button ....................... ........... ........... ............ ........... ........... ........... ............ ........... ........... .. 48

4.11.2. In reset of Factory default ................... ........... ............ ........... ........... ........... ............ ........... .... 48

5. BASIC USE........................................................................ 50

5.1. USE OF WEB VIEWER ........................................................................................ 50

5.2. USE OF OSD (NOT AVAILABLE WITH IP-T5).................................................... 53

5.2.1. Function. ............ ........... ........... ............ ........... ........... ............ ........... ........... ........... ............ ........ 53

5.2.2. OSD Menu Setting ........ ............ ........... ........... ............ ........... ........... ........... ............ ........... ...... 56

5.2.3. Operating Camera OSD Menu (Intensifier Cameras) .................. ........... ........... ............ .... 57

5.2.4. Operating WDR Camera OSD Menu (IP-WDRB1).... ........... ........... ............ ........... ........... .. 77

5.2.5. Operating Camera OSD Menu (IP-SD10X) ...................... ........... ........... ............ ........... ...... 79

5.2.6. DIP SW SETTING ................ ............ ........... ........... ........... ............ ........... ........... ............ ........... 97

5.2.7. ID SETTING(1-ON, 0-OFF)(110) ................. ........... ........... ............ ........... ........... ............ . 97

5.2.8. PROTOCOL ........ ........... ........... ........... ............ ........... ........... ............ ........... ........... ............ ....... 98

5.2.9. BAUD RATE SETTING ..................... ............ ........... ........... ........... ............ ........... ........... .......... 98

IP Camera User’s Manual Speco Technologies

5.3. USE OF IP SETTING UTILITY.............................................................................. 99

5.4. USE OF SERVICE SERVER................................................................................ 101

5.4.1. User Registration .................... ........... ........... ............ ........... ........... ............ ........... ........... ...... 102

5.4.2. Camera Registration.. ........... ........... ............ ........... ........... ........... ............ ........... ........... ........ 104

5.4.3. List of Camera ...... ........... ........... ........... ............ ........... ........... ............ ........... ........... ........... ... 105

5.4.4. Change of User’s Information ....... ........... ............ ........... ........... ............ ........... ........... ........ 107

5.4.5. Search Camera..... ........... ........... ........... ............ ........... ........... ............ ........... ........... ........... . 108

5.5. SEE AND CONTROL OF STILL IMAGE IN MOBILE OR PDA ................................ 109

5.5.1. WAP2.0 (HTML)............ ........... ........... ............ ........... ........... ............ ........... ........... ........... ...... 109

5.5.2. PDA(WinCE) ....... ........... ........... ........... ............ ........... ........... ............ ........... ........... ........... .......112

5.6. USE OF NVR PROGRAM...................................................................................113

5.6.1. Required Specification of PC and OS ...................... ........... ........... ............ ........... ........... ...113

5.6.2. Supported O/S .................... ........... ............ ........... ........... ............ ........... ........... ........... ...........113

5.6.3. Refer the NVR User’s Manual in the CD-ROM. .. ............ ........... ........... ........... ............ ......113

6. NETWORK ENVIRONMENT ..................................................115

7. APPENDIX........................................................................118

IP Camera User’s Manual Speco Technologies

1. Feature

IP Camera User’s Manual Speco Technologies

1. Feature

1.1. Package

IP/Network Camera

Package of Products is composed of main body of product, Software CD (NVR Program, IP Utility,

Product Manual, NVR Manual) , Quick Install Guide, Cross LAN Cable, Accessory Pack, Power Lead

Cable.

Please check before starting installation.

Cross LAN Cable

Software CD

Quick Install Guide

Power Lead Cable Accessory Pack

③ ②

② ③

1.2. Dimension and Camera Features

1.2.1. Dimensions

1) Bullet Camera

①

2) Dome Camera

①

IP Camera User’s Manual Speco Technologies

③ ②

② ③

3) Traditional Camera

①

3) Speed Dome Camera

①

1) Power Port: Power connection port (12 VDC)

2) VIDEO Port : Video Output Port (BNC)

3) LAN Port: LAN Connection Port ( Connect with LAN Cable for Local Network or Internet

Viewing)

 LINK: LED On (When the product connects with LAN Cable)

 DATA: LED On (When user connects the product to the Network)

IP Camera User’s Manual Speco Technologies

1.2.2. Camera Feature

I. Intensifier Cameras (Not available with IP-T5)

1) SLC ( Speco Light Compensation )

: When the image is in front of strong background lighting, your camera

allows you to get a clear image.

2) Intensifier: 1/3 inch double density CCD and digital processor permit high quality pictures

to be captured in very low light conditions.

3) High Resolution: The horizontal resolution of 540TV lines is achieved by using a

SONY CCD having Double Speed 410,000 pixels.

4) Motion Detection: Video motion detection is built in to the camera.

5) OSD: Full on screen control of all critical features.

6) Reduce Noise : A DSP chip that removes image noise efficiently in low light conditions.

7) Electronic Day/Night: Allows the camera to always remain in color or to switch into B/W at

night.

8) Manual/DC Lens : You can choose MANUAL or DC LENS by using this switch.

II. Speed Dome Camera

1) DVD Quality Video Streaming

2) MPEG4, JPEG Triple stream capability

3) 100X Zoom(10X Optical Zoom with 10X digital zoom)

4) ±0.02° dome system accuracy with 1/4 micro step

5) 360° Endless Rotation

6) Compensation function: preset position

7) Over 200°/Sec Preset Speed

8) Polarity Protection of Power (DC12V)

9) Filter changeable True Day/Night

10) Various Surveillance Functions

11) Auto Scan / 8 Group Tour / 20 Preset positions / 8 Patterns / 8 Sectors

12) 2 Alarm input

13) 4 Privacy Masking Zones

14) High picture quality 1/4” SuperHAD CCD

15) High sensitivity 0.1 lux / 0.002 lux(Sense-up x128) 11

16) Camera OSD control with client program

17) Super Day/Night Function with Power Sensor-up engine

18) Intelligent Pan/Tilt Controlling

19) High-frame rate of up to 30fps at 704x480 size image

20) 4 selectable image sizes – D1,Half D1,2CIF,CIF

21) Simultaneous access up to 20 users

22) Intelligent motion detection and alarm trigger function

23) Pre-alarm recording with ftp server

24) Networking security : Password protection & Encryption

25) Access priority setting capability

26) Analog composite video output for local analog viewing or recording

27) Supports NVR@PC, Viewer@PDA, Mobile Phone

III. WDR Camera

1) High picture quality 1/3” CMOS

2) High Resolution of 540TV Line

3) Superior Wide Dynamic Image Quality

4) Digital pixel System

5) Weatherproof Design with IP66

6) Single body type stand: Protect video and power line

7) OSD Control

- Auto White balance

- Automatic gain control(max.38dB)

- Slow shutter, agc on/off

- Lens type control

- Auto exposure control

8) Synchronization: Internal/External selectable

9) Camera ID:User writable camera title

10) MPEG4,JPEG Triple stream capability

11) Intelligent Motion detection and alarm trigger function

12) Pre-alarm recording

13) Networking security: Password protection

14) Analog composite video output for local analog viewing or recording

15) Supports NVR@PC, Viewer@PDA, Mobile Phone

IP Camera User’s Manual Speco Technologies

2. Install and Check Video

IP Camera User’s Manual Speco Technologies

2. Install and Check Video

2.1. Installation

1) Connect the IP Camera to the PC by LAN cable (Crossover Cable)

2) Supply power to the camera using a 12 volt DC regulated power supply.

3) Wait approximately 2 minutes until the Link/LED light comes on.

2.2. Video Check

Basic network setting value of the camera is to be:

 IP Address: 192.168.1.7

 Subnet Mask: 255.255.255.0

 Gateway: 192.168.1.1

To connect THE CAMERA into the user’s PC, change the setting value of the PC network

environment.

Fig. 2―1 Network Setting of User PC

IP Camera User’s Manual Speco Technologies

1) Set IP Address, Subnet Mask and Gate-way of User’s PC with 192.168.1.50, 255.255.255.0

and 192.168.1.1 as shown on [Fig. 2-1].

Fig. 2―2 Web Browser Input

2) Run Web Browser as [2-2] and input 192.168.1.7 in URL and click “Enter”, then [2-3] is

shown. In case [2-3] does not appear, re-set Hardware (Reset Button in Camera) to reboot

and run Web Browser, input 192.168.1.7 in URL line and click “Enter” .

Fig. 2―3 THE CAMERA Main Page

3) Click “Connect” Button of [Fig. 2-3].

(1)

Fig. 2―4 User login

4) Input ID and Password on [Fig. 2-4] to see Video.

5) User’s Authority to see Video on THE CAMERA is as follows ;

Table 2-1 User ID, Password, Rights

IP Camera User’s Manual Speco Technologies

User ID User Password

Guest Guest Monitor only

PTZ (select models only) PTZ Monitor, Control of P/T/Z,

Control of Relay

Audio (select models only) Audio Monitor, Hearing

Iaudio (select models only) Iaudio Monitor, Bi-directional Audio

PCAudio (select models only) PC Audio Monitor, P/T/Z, Relay Control,

Hearing (1 way Audio)

root root All Function

6) Above [Table 2-1] is the value set in THE CAMERA. Change the User Information in

‘General Setting’ after installing the camera.

7) Click (1) after input ID: root, Password :root in [2-4].

8) Message Window [2-5] appear soon, click ‘Yes’.

Rights

IP Camera User’s Manual Speco Technologies

Fig. 2―5 ActiveX Download

9) Upon installation, Web Viewer [Fig. 2-6] appears and the image of the Camera can be

seen.

Fig. 2―6 Web Viewer

10) After checking proper operation as seen on [Pic 2-6], go onto the next Chapter (3) Basic

Setting.

11) Refer to (5) Basic Use’ to see the details of how to use Web Viewer.

IP Camera User’s Manual Speco Technologies

3. Basic Setting

IP Camera User’s Manual Speco Technologies

3. Basic Setting

3.1. Check Network and Installation Type

This Chapter is for basic setting of THE CAMERA. To install Hardware of the Network Camera,

basic understanding of Networking is required.

Network Environment is required.

CAMERA without IP sharing Device under Cable Modem or Leased Line, the other one is to install

THE CAMERA under an IP sharing Device , which is required necessarily under PPPoE environment,

and even under Leased Line or Cable Modem. The default IP Address of THE CAMERA is preset to

192.168.1.7 and Subnet Mask to 255.255.255.0 and Gateway to 192.168.1.1 in the factory. This

explanation is based upon default value of the factory.

Caution 1 : Check Video before installation, on ‘

Caution 2 : In case using IP sharing Device, only Global IP is available.

Caution 3 : THE CAMERA does not support PPPoE. IP Sharing Device is required to connect to

THE CAMERA under PPPoE.

Installation without IP sharing device

-> For static IP, refer to ‘Static IP Setup’.

-> For dynamic IP, refer to ’ Dynamic IP Setup’.

Installation with IP sharing device

-> Should set up with Static IP. Refer to ‘Installation with IP Sharing Device’.

There are 2 ways to install Hardware. One is to install THE

Please refer to Chapter 6 in case knowledge of

2. Install and Video Check’.

IP Camera User’s Manual Speco Technologies

3.2. Installation without IP sharing device (Router)

3.2.1. Static IP Setup

1) After checking Video in ‘Video Check’, go to the next step.

2) Connect THE CAMERA to PC with LAN Cable (Crossover Cable).

3) Cable connection and Network Setup should be same as shown in ‘

Video Check’.

4) Run Web Browser and input 192.168.1.7 in URL and click ‘Enter’, then [Fig. 3-1] will

appear.

2. Install and

Fig. 3―1 Main Page of THE CAMERA Network Camera

5) Click ‘Administrator’s Page’ of [Fig. 3-1], then Browser shows [3-2] Log-in

Page.

Fig. 3―2 Administrator Page Log-in

IP Camera User’s Manual Speco Technologies

6) Put ‘admin’ in ID and Password line, click ‘Login’, then [3-3] ‘Administrator's Page’

will be shown. (ID, Password of THE CAMERA is preset as admin/admin in

Administrator’s Page. Change Administrator’s ID and Password in General Setting of ‘

Expert Setting’

Fig. 3―3 Administrator’s Page

7) Click “Network Setting’ in left menu on [3-3], [3-4] appears.

8) Click ‘Static IP Address’ in ‘IP Setting’ of [3-4], and input IP Address, Subnet Mask,

Default Gateway according to Network environment to connected THE CAMERA to.

9) For setting of ‘DNS Server’, input DNS Address to fit with Network Environment to set.

Use DNS value normally set in PC.

10) DNS Address must be entered.

11) Click ‘Save’ Button of [3-4] to save setting value.

IP Camera User’s Manual Speco Technologies

Fig. 3―4 Network Setting

12) Click ‘Click Here’ upon appearing of IP Change Window of [3-5].

13) IP Change loading Page appears as [3-6], the Main Page of changed address is

connected. (Note: You may not find the main page of changed address under

Cross Cable connection, but IP has been changed.)

Pic 3―5 IP Change

IP Camera User’s Manual Speco Technologies

Fig. 3―6 IP Change loading Page

14) Remove LAN Cable (Cross Cable) connected between THE CAMERA and PC.

15) Connect THE CAMERA to Network with LAN Cable (Straight Cable).

16) Connect PC to Network with LAN Cable (Straight Cable)..

17) Set up IP Address, Subnet Mask and Gateway of PC according to the Network

environment.

18) Check

 Run Web Browser on PC, input IP address set in THE CAMERA onto URL

and click ‘Enter’,

 Check if IP Setting is correct or not, referring to ‘Video Check’

 If Video is seen, THE CAMERA has been correctly set up.

 If Video is not seen, check whether there may be a conflict of IP in the

Network, and re-check the set value of Network environment of THE

CAMERA, and Network environment of User’s PC.

3.2.2. Dynamic IP Setup

 Do not set up Dynamic IP in the camera except as a direct

connection of Cable Modem supporting Dynamic IP with the

camera.

 Reset, in case IP has not been allocated to THE CAMERA in

Dynamic IP Setting, to go to Initial Value and try again.

1) After checking Video in ‘Video Check’, then go to the next step.

2) Connect THE CAMERA and LAN Cable (Cross Cable)

3) Cable Connection and Network Setting should be done same as per ‘

Video Check’.

2. Install and

IP Camera User’s Manual Speco Technologies

4) Go to Network Setting Page of Administrator’s Page as per 4), 5), 6), 7) of ‘Static

IP Setup’.

Fig. 3―7 Network Setting

5) Click on ‘Dynamic IP Address’ in ‘IP Setting’.

6) Click ‘Save’ Button.

7) Upon completion of setting, close the Web Page and find IP of THE CAMERA in ‘IP

Utility’

program provided with Proprietary Viewer (see ‘5. Basic Use’)

8) If the IP is found, THE CAMERA has been given an IP. But in case the IP is not found,

do a re-set of [2-1] to go to initial value because it has not been given an IP,

then re-start the IP Setting. Once THE CAMERA has an IP, remove the LAN Cable

(Crossover Cable) connected between THE CAMERA and the PC.

9) Connect THE CAMERA to the Network with LAN Cable (Straight Cable).

10) Connect PC to Network with LAN Cable (Straight Cable).

11) Set IP address of PC, Subnet Mask and Gateway properly according to the Network

Environment.

12) Check

After registration of THE CAMERA in Service Server (refer to ‘Use of Service Server’ of ‘ 5.

Basic Use’,

IP Camera User’s Manual Speco Technologies

connect to THE CAMERA by Domain Name (Server Name) allocated to THE CAMERA.

For example, run Web Browser and input Domain Name allocated to THE CAMERA in URL.

In http://IPXXXXX.ipcam4u.net, ‘IPXXXXX’ is to be Name of Server registered in Service

Server by user.

If the initial page is shown as [3-8], check Video of THE CAMERA referring to ‘2. Install

and Video Check’. If Video is seen, set up is properly done.

Fig. 3―8 Initial Page of THE CAMERA

3.3. Installation with IP Sharing Device (Router)

1) After checking Video in

2) Connect THE CAMERA and PC with LAN Cable (Crossover Cable).

3) Cable Connection and Network Setting should be done same as per

Video Check’.

4) Go to Network Setting Page of Administrator’s Page as per 4), 5), 6), 7) of ‘Static IP

Setup’.

5) Click ‘Static IP Address’ in ‘IP Setting’ of [3-9], and input IP Address, Subnet Mask,

Default Gateway according to Network environment to connected THE CAMERA to.

6) For setting of ‘DNS Server’, input DNS Address to fit with Network Environment to set.

Use DNS value normally set in PC.

‘2. Install and Video Check’, then go to the next step.

‘2. Install and

IP Camera User’s Manual Speco Technologies

7) DNS Address should be input. In case THE CAMERA is installed under IP Sharing

Device, input local IP of Router in 2nd DNS Server Address.

8) Click ‘Save’ Button of [3-9] to save the set value.

Fig. 3―9 Network Setting

9) Click ‘Click Here’ upon appearing of IP Change Window of [3-10].

10) IP Change loading Page appears as [3-11], the Main Page of changed address is

connected. (may not find the main page of changed address under Crossover Cable

connection, but IP has been changed.)

IP Camera User’s Manual Speco Technologies

Fig. 3―10 IP Change

11) It is connected to the new IP set up, in 20 seconds after window of [3-11] appears.

12) Check Video of THE CAMERA referring to

is connected to the new IP.

13) Go to Network Setting Page of Administrator’s Page as per 4), 5), 6), 7) of ‘Static

IP Setup’.

‘2. Install and Video Check’ as soon as it

Fig. 3―11 IP Change loading Page

Fig. 3―12 Port Setting

IP Camera User’s Manual Speco Technologies

14) Set Port in Port Setting Page of [3-12]. It is required to set each different Port for

many THE CAMERA Network Cameras under 1 Router.

15) Click ‘Save’ Button to save set value.

16) Remove LAN Cable (Crossover Cable) connected between THE CAMERA and PC.

17) Connect THE CAMERA to Network with LAN Cable (Straight Cable).

18) Connect PC to Network with LAN Cable (Straight Cable).

19) Port-Forward the port designated to use THE CAMERA, in IP Sharing Device. Refer

to manual of IP Sharing Device for details.

20) Check 1 (local check)

Run Web Browser and input IP address of THE CAMERA in URL and click ‘Enter’. If you

changed Web Server Port, you must input ‘http://IP Address:Port Number’. For example, if

you set IP address of THE CAMERA to 192.168.10.88 and changed Web Server port to 81,

you must input

http://192.168.10.88:81.

Fig. 3―13 Main Page of THE CAMERA

After [3-13] appears, check Video of THE CAMERA referring to‘

21) Check 2 (Check from outside)

After registration of THE CAMERA in Service Server (refer to ‘‘

Basic Use’,

2. Install and Video Check’.

Use of Service Server’ of ‘‘ 5.

IP Camera User’s Manual Speco Technologies

connect to THE CAMERA by Domain Name (Server Name) allocated to THE CAMERA.

For example, run Web Browser and input Domain Name allocated to THE CAMERA in URL.

In http://IPINTB1.ipcam4u.net , ‘IPINTB1’ is to be Name of Server registered in Service

Server by user.

If the initial page is shown, check Video of THE CAMERA referring to ‘2. Install and

Video Check’. If Video is seen, set up is properly done.

3.4. Cautions

If the firewall is used for security purpose, THE CAMERA may not work properly. In this case, open

the port of THE CAMERA, then it will work properly. The port being used by THE CAMERA can be

checked

on ‘Port Setting’ of ‘Network Setting’ of ‘Administrator’s Page’.

Port of THE CAMERA on ex-factory is set default as follows ;

 Web Connection Port: Port 80 TCP

 Authentication and Control Port: Port 9000 TCP

 Video Streaming Port: Port 9001 TCP

 Motion Detection Control Port : Port 9005 TCP

In setting user port, do not use 1504, 1508, which port is used in THE CAMERA itself.

IP Camera User’s Manual Speco Technologies

4. Expert Setting

+ 96 hidden pages