Speco Technologies SIPSD37X, HTSD37X User Manual

SIPSD37X & HTSD37X

37X Optical Indoor / Outdoor Speed Dome Cameras

200 New Hightway

Amityville, NY 11701

631-957-8700

www.specotech.com

Speco Technologies is constantly developing product improvements. We reserve the right to

modify product design and specifications without notice and without incurring any obligation.

Rev. 03082010.

CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN THE COVERS.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONAL

This lightning flash with arrowhead symbol is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

This Device compiles with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interface, and (2) This device must acc ept any interference received, including inte rference that

may cause undesired operations.

37X Speed Dome Camera 2/50

Important Safety Guide

NOTICE

1. Read and follow all the Instructions

Read all the safety and operating instructions before using the product.

2. Keep this manual

Keep this manual for reference in future.

3. Attachments / Accessories

Use only the attachments or accessories specified by the manufacturer.

4. Installation z Do not install near any heat sources such as radiators, heat registers, stoves, or other

appratus including amplifiers that product heat.

z Improperly installed product may fall, cause serious injury to a child or adult and

damage the product.

z Do not block any ventilation holes or openings. Install in accordance with the

manufacturer’s instructions.

z Use only with the cart, stand, tripod, bracket, mounting devices, or table specified by

the manufacturer.

z Installation should be done only by qualified personnel and conform to all the

instructions by the manufacturer.

z Refer all servicing to qualified service personnel. z Use stainless steel hardware to fasten the mount. z To prevent damage from water leakage when installing a mount outdoors on a roof or

wall, apply sealant properly around holes.

z These servicing instructions are for use by qualified service personnel only. To reduce

the risk of electric shock, do not perform any servicing other that contained in the operationg instructions unless you are qualified to do so.

z Use only replacement parts specified by the manufacturer.

5. Power source

This product should be operated only from the type of the power source indicated on the marking label.

37X Speed Dome Camera 3/50

 Operating

 Handling

 Installation and Storage

Caution

z Before using, make sure that the power supply is properly installed. z While operating, if any abnormal condition or malfunction is observed, stop using the

product immediately and then contact your local dealer.

z Do not disassemble or tamper with the parts inside the product. z Do not drop or subject the product to shock and vibration as this can damage the

product.

z Care must be taken when you clean the clear dome cover. Especially, scratch and dust

will ruin the quality of the product.

z Do not install the product in areas of extreme temperature, which exceed the allowable

range.

z Avoid installing in places where radiation is present. z Avoid installing in places where there are strong magnetic fields and electric signals. z Avoid installing in places where the product would be subject to strong vibrations.

NOTICE

37X Speed Dome Camera 4/50

Package Components

Main Part Description

Installation with Wall Mount Bracket

Wiring and Cabling

Check Points before Operation

Check Points for Preset and Pattern Function before

Reserved Preset (Hot Keys)

Quick Programming Guide

Privacy Zone Mask Setup

System Initialization

⑤ Specifications

37X Speed Dome Camera 5/50

TABLE OF CONTENTS

① Introduction

Feat ure s

② Installation

DIP Switch Setup

③ Operation

Operation

OSD Menu

Preset

Swing

Pattern

Group

Other Functions

OSD Display

④ OSD Menu

Main Menu

Display Setup

Camera Setup

Motion Setup

Preset Setup

Setup

Swin

Pattern Setup

Group Setup

Dimensions

⑥ Wa r ra n ty

Fe at ur es

 Powerful Zoom Camera & Setup Options

z Image Sensor: Sony 1/4" Double density interline transfer CCD z Zoom: 37X Optical Zoom, 12X Digital Zoom

z Day & Night, Privacy Mask and WDR z SNR (Super Noise Reduction) Function z Various Focus Modes: Auto-Focus, Manual Focus, Semi-Auto Focus

z Various Setup Options in OSD Menu.

 Powerful Pan/Tilt Functions

z MAX. 360°/sec High Speed Pan/Tilt Motion z With the Vector Drive Technology, Pan/Tilt motions are accomplished along the

shortest path. As a result, the time to target view is remarkably shortened and the video on the monitor is very natural.

z With the Micro-Stepping Control Technology, the video looks very natural at high

zoom magnification during a jog operation on a controller since the camera can be controlled by 0.05°/sec. Hence it is very easy to make the camera focus on desired target views at high zoom magnification. Additionally it is easy to make the camera focus on desired positions with zoom-proportional pan/tilt movement.

 Preset, Pattern, Swing, Group, Privacy Mask and More…

z MAX. 127 Presets are programmable and each preset can have its own parameter

values independently from the other presets. For an example, refer to the below table.

Preset No. White Balance Auto Exposure ••• Label Remarks

Preset 1 Case A Case 3 “ENTRANCE”

Preset 2 Case C Case 5 “WAREHOUSE”

•••

Preset 95 − − − − Reserved for OSD Menu

•••

Preset 128 Case K Case 9 “TERRACE”

INTRODUCTION 1

37X Speed Dome Camera 6/50

z MAX. 8 sets of Swing are programmable. This function is that the camera moves

repetitively between two preset positions at programmed speeds.

z MAX. 4 Patterns are programmable. This function is that the camera memorizes the

path (mostly curve path) by the joystick of the controller and revives the trajectory operated by the joystick as closely as possible.

z MAX. 8 sets of Group are programmable. This function is that the camera memorizes

the combination of Presets, Pattern and/or Swings sequently and runs Presets, Pattern and/or Swings repetitively. A Group can be combined upto 20 functions with any of Preset/Pattern/Swing.

z MAX. 8 or 4 Privacy Masks are programmable, not to intrude on any other’s privacy.

 PTZ(Pan/Tilt/Zoom) Control

z With the RS-485 communication connection, MAX. 255 units of cameras can be

connected to a single controller.

z Pelco-D or Pelco-P protocols can be selected as a control protocol in the current

firmware version.

 OSD(On Screen Display) Menu

z OSD menu is provided to display the status of camera and to configure the functions

interactively.

z The information such as Camera ID, Pan/Tilt Angle, Direction, Alarm Input and Preset

is displayed on screen.

Alarm In/Out Function(Only for the models which have I/O function)



z 3 alarm sensor inputs and 1 alarm sensor outputs are available. z Alarm sensor input is decoupled with photo-couplers to avoid external electric noise

and shock perfectly.

z Both of N.O.(Normal Open) sensors and N.C.(Normal Close) sensors can be used and

the signal range of the sensor input is from DC 5.0V to 12.0V for various applications.

z The camera can be set to move to a Preset position or to run functions such as Pattern,

Swing and Group when there are external sensor activations. Also “Post Alarm” function is possible, which is supposed to activate after user-defined time period and

 Reserved Presets(Hot Keys)

sequentially in succession to the action by external sensor activations.

z Most camera setup options can be set up easily and directly with the reserved presets

(Hot Keys), without entering into OSD menu. For more information, refer to “Reserved Presets(Hot Keys)” in this manual.

INTRODUCTION 1

37X Speed Dome Camera 7/50

 Network Function(Only for the SIPSD37X)

z Network functions including remote monitoring, bidirectional audio and others are

available through IP based network such as LAN, ADSL/VDSL, and Wireless LAN. For



more information, refer to the separated manual for IP Addressable models.

Perfect Outdoor Environment Compatibility and Easy Installation

z The fans and heaters are built-in in the camera for cold and hot temperature

environment. Also idealistic mechanical design protects the camera from water and dust. (IP67 when installed properly with wall mount bracket only / Only for outdoor models)

INTRODUCTION 1

37X Speed Dome Camera 8/50

 Product & Accessories

Package Component

INTRODUCTION 1

z Main Body & Surface Mount Bracket z Default Accessories

z Accessories for The Models with Alarm

In/Out Function [I/O Cable]

 Wall Mount Brackets (Included)

[Main Cable, Wrench]

z Accessories for The IP Addressable Models

[Crossover LAN Cable, Audio Cable, CD]

SIPSD37X Only

[Screws : Machine M5×15, Hex Lag #14×50]

37X Speed Dome Camera 9/50

)

Main Part Description

INTRODUCTION 1

Mounting Screw Hole

Drop Prevention Spring

DIP Switch

Reset Switch (IP Model) LAN Port (IP Model) Audio Port (IP Model) Main Connector Sensor I/O Port (I/O Model

Dome Cover

z Dome Cover Do not detach the protection vinyl from the dome cover before

finishing all the installation process to protect the dome cover from scratches or dust.

z DIP Switch Used to set up camera IDs and protocols.

z Drop Prevention

Spring

This part keeps the camera from dropping during installation and maintenance. After install the Bracket, please, hang the spring to the drop prevention hook of main body as shown in picture for further tasks.

z Mounting Screw Hole Used to assemble the main body with a bracket with screws.

z Main Connector Use d for t h e powe r wire, t he vi deo c a ble a nd th e RS-4 85

communication cable connection.

z Sensor I/O Port Used for the sensor in/out connection. (The sensor I/O function

possible models only)

z LAN Port Used for the Ethernet connection. (IP addressable models only)

z Audio Port Used for the audio in/out connection. (IP addressable models

only)

z Reset Switch Used to initialize all the network configurations to the factory

default. (IP addressable models only) Press the button for more than 5 seconds to initialize the network system.

37X Speed Dome Camera 10/50

INSTALLATION 2

DIP Switch Setup

Before installing the camera, set up the DIP switch to configure the camera ID and the communication protocol.

 Camera ID Setup

12345678

z ID numbers of cameras are set up with binary numbers.

See the examples shown below.

Pin 1 2 3 4 5 6 7 8

Binary Value 1 2 4 8 16 32 64 128

ex) ID=5 on off on off off off off off ex) ID=10 off on off on off off off off

z The camera ID range is “1~255”. Camera ID must not be

“0”!

z The factory default of the camera ID is “1”. z Match the camera ID with the Cam ID setting of your DVR

or Controller to control the camera.

z If you are connecting a single camera to a controller,

terminate the camera. When connecting more than one camera to a single controller, terminate the last camera on the communication line. The last camera means the camera farthest in cable length from the controller.

z Note that the total length of the communication cable

between a controller and the camera(s) on the same communication line must be less than 1.2Km.

37X Speed Dome Camera 11/50

 Communication Protocol Setup

z Select an appropriate Protocol with the DIP switch combination.

1234

(Pin 1)

OFF OFF OFF PELCO-D, 2400 bps

ON OFF OFF PELCO-D, 9600 bps

OFF ON OFF PELCO-P, 4800 bps

ON ON OFF PELCO-P, 9600 bps

z Match the camera protocol with the camera protocol in the setting of

your DVR or controller to control the camera.

z Adjust the DIP switch after turning off the camera. If you changed the

camera protocol by changing the DIP S/W, the change will be effective after you reboot the camera.

z The factory default protocol is “Pelco-D, 2400 bps”. (HTSD37X) z The factory default protocol is “Pelco-D, 9600 bps”. (SIPSD37X)

INSTALLATION 2

Switch Mode

(Pin 2)

(Pin 3)

Protocol

Others Reserved

37X Speed Dome Camera 12/50

 Terminal Resistor Setup

1234

INSTALLATION 2

he terminal resistor is used for the following cases.

z Case 1 : In case that the control cable length between a camera

and a controller is relatively very long (1:1 Connection)

If the communication cable length is very long, the electrical signal will bound in the terminal point. This reflected signal causes distortion of original signal. Accordingly, the camera can be out of control. In this case, the terminal resistor of both sides i.e. the camera and the controller must be set to ‘ON’ state.

z Case 2 : In case that multiple cameras are connected to a

controller.

Due to similar reasons with the case 1, the terminal resister of the controller and the last camera must be set to ‘ON’ state. The last camera means the camera farthest in cable length from the controller. Do not turn on the terminal resistor of all the cameras on the same communication cable.

Controller

Terminal Resistor ON

RS-485

#1 #2 #n

Terminal Resistor

OFF

Terminal Resistor

OFF

Terminal Resistor

37X Speed Dome Camera 13/50

① Make a hole whose diameter is 30~40mm

③ Line up the mold lines and assemble

Installation with Wall Mount Bracket

on the mounting surface to pass the wire(s) and cable(s) through the mounting surface. (In case of the wiring and cabling through the mounting surface only) Then prepare the wall mount bracket. Pull the wire(s) and cable(s) for the system as below. Attach the wall mount bracket to the mounting surface. (Hex Lag #14×50)

main body to mount adaptor and turn it. And assemble the main both with the camera mount adaptor with the 3 screws. (Machine M5×15).

INSTALLATION 2

② Hook up “Drop Prevention Spring” on

main body to prevent camera from unexpected drop and pull the wire(s) and cable(s) for the system as below.

④ Screw the dome cover to the main body

and remove the protection vinyl from the dome cover.

Important Notice

z Before starting the installation, make sure that the Camera ID and Protocol are set up properly.

37X Speed Dome Camera 14/50

Wiring and Cabling

BROWSER

MIC SPEAKER

 Port Description

z Main Cable

Port Pin Number (RJ45) Connector / Wire Color Signal

z I/O Cable

Port Pin Number (RJ25) Wire Color Signal

INTERNET

LAN CABLE

UDIO

CABLE

MAIN CABLE

POWER

BNC

RS-485

I/O CABLE

INSTALLATION 2

MONITO

CONTROLLER / DVR

SENSOR I/O

I SENSOR

DOOR SWITCH

1 Video +

2,4

BNC Connector

Video −

5 Red RS-485 +

3 Yellow RS-485 −

7 Orange Power +

6,8 White Power −

1 Blue IN COM +

2 Yellow IN 1 −

3 Green IN 2 −

4 Red IN 3 −

5 Black OUT A

6 White OUT B

37X Speed Dome Camera 15/50

+ 35 hidden pages