Speco Technologies HT-INTB1, HT-INTB2 User Manual

Intensifier Series
Camera
HT-INTB1 HT-INTB2
200 New Highway
Amityville, NY 11701
631-957-8700
www.specotech.com
Please read this manual thoroughly before operation and keep it handy for further reference.
Contents
Package Contents
Precautions
Camera Installation
Focusing
Features
3
4
5
6
7~8
Operating Your Camera
------------------------9
* SET UP --------------------------------------------------------------11~12 * SET UP LENS ------------------------------------------------------13~14
* SHUTTER SPEED CONTROL ----------------------------------15~18 * BACK LIGHT--------------------------------------------------------------19 * AUTO GAIN (AGC) -----------------------------------------------------20 * WHITE BALANCE --------------------------------------------------21~22
* REDUCE NOISE---------------------------------------------------------23 * INTENSIFIER-------------------------------------------------------------24
* CAMERA TITLE-------------------------------------------------------25~26 * DAY/NIGHT/SYNC----------------------------------------------------27~28 * MOTION DETECTION-----------------------------------------------29~30 * PRIVACY-------------------------------------------------------------------31 * REVERSE------------------------------------------------------------------32 * DETAIL----------------------------------------------------------------------33 * DEFAULT/RETURN-----------------------------------------------------34
Troubleshooting
Specifications / Dimensions
35~36
37~38
Warranty
1 2
39
PACKAGE CONTENTS
PRECAUTIONS
Please make sure that the following items are included
in the package:
1 HT-INTB CAMERA
1 SUNSHIELD
1 REMOTE CONTROLLER
1 IR RECEIVER
4 MOUNTING SCREWS
1 M2.6 WRENCH (“L" TYPE)
1 VIDEO TEST CABLE
1 POWER CABLE ADAPTOR (for optional use)
Please leave this manual with the end-user for future
reference.
TO PREVENT A FIRE OR ELECTRICAL HAZARD PLEASE USE
PROPER POWER CABLE
INSTALLATION SHOULD BE PERFORMED BY QUALIFIED
PERSONNEL
PLEASE USE A UL APPROVED REGULATED 24 VOLT AC OR
12 VOLT DC POWER SUPPLY
PLEASE USE APPROPRIATE LOW VOLTAGE POWER CABLE
TO PREVENT FIRE OR ELECTRICAL SHOCK.
PLEASE INSURE THAT YOUR INSTALLATION AREA CAN
SUPPORT THE WEIGHT OF THE CAMERA.
PLEASE HANDLE THIS CAMERA CAREFULLY:
- DON’T USE A STRONG OR ABRASIVE DETERGENT WHEN CLEANING THE CAMERA.
- USE A SOFT TISSUE OR LENS CLOTH TO CLEAN THE FRONT GLASS
- DON’T EXPOSE THE CAMERA TO DIRECT SUN
3 4
CAMERA INSTALLATION
FOCUSING
CONNECT POWER CABLE
1. WHEN USING 12 VOLTS DC (constant voltage 600 mA)
CONNECT
POWER SUPPLY
2. WHEN USING 24 VOLTS AC (40 Volt Amps)
POWER RED(+)
BLACK:(-)
3. CONNECT VIDEO CABLE
-CONNECT BNC CABLE TO THE BNC JACK.
CONNECT
POWER SUPPLY
YELLOW:VIDEO OUT
3~9 mm
1. SET THE ZOOM OR FIELD OF VIEW BY USING THE ZOOM CONTROLLER (3-9mm or 5~50mm)
SET THE FOCUS BY USING THE FOCUS CONTROLLER.
LOCK BOTH RINGS INTO POSITION USING THE SET­SCREWS.
5~50 mm
5 6
Features
SLC
When the image is in front of strong background lighting, your camera allows you to get the best image.
INTENSIFIER
1/3 inch high density CCD and digital processor permit high quality pictures to be captured in very low light conditions.
High Resolution
Horizontal resolution of 530 TV lines is achieved by using a SONY Double Speed CCD with 410,000 pixels, yielding pictures with a high S/N ratio.
OSD
All camera functions are menu driven for ease of use.
Dynamic Noise Reduction
The Intensifier camera has a DSP chip that can remove image noise efficiently showing clean images in low light conditions.
ELECTRONIC DAY / NIGHT
The Intensifier camera can show color pictures in all lighting conditions, or you can have it automatically switch to a B/W picture in low light conditions
Motion Detection
Built in motion detector with adjustable areas of coverage will flash a warning on the screen when motion is detected.
7 8
MANUAL / AUTO IRIS LENS
The Intensifier camera will work with auto iris,manual iris and
fixed iris lenses.
Operating your camera
Function
SET UP MENU
LENS OPTION
DC MANUAL
SHUTTER
OFF F/L MANUAL
WHITE BALANCE
ATW AWC MANUAL
SLC – ( Speco Light Compensation )
OFF LOW MIDDLE HIGH
Auto Gain
OFF LOW MIDDLE HIGH
REDUCE NOISE
OFF LOW MIDDLE HIGH
INTENSIFIER
AUTO OFF
NEXT PAGE
CAMERA TITEL DAY/NIGHT SYNC
MOTION PRIVACY REVERSE
DETAIL DEFAULT PAGE 1
EXIT
9 10
Operating your camera
1. When controlled by RS-485, Pelco-D protocol (Option), refer to the following.
A. DIP Switch Setting on the Camera
(Factory default : Camera Address = 01, Baud Rate = 2400bps)
①②
RS485 Address Set
RS485 Baud rate Set
•Up to 15 Cameras can be controlled by 1 IR Remote Controller & 1 Receiver. You must set up each camera’s address by DIP Switches for proper addressing.
B. Receiver Setting to use with IR Remote Controller
(Factory default : Baud Rate = 2400bps, Chart is same as above)
Buzzer On/Off
Power Connector (DC12V in)
485(+),(-)
Baud Rate Setting
C. System Integration
•Please Observe Polarity!
485(+)
485(-)
Receiver
IR Remote
Multiplexer
Monitor
Controller
CCD Camera
D. IR Remote Controller
- Can call and control each camera on the monitor by the following.
SET / Menu buttonUP button
LEFT button
RIGHT button
DOWN button
When you call Camera Address 01
->Push 0 Button
->Push 1 Button
->Push CAM Button
11 12

Operating your camera Operating your camera - LENS

1. Press the SET button to access the SETUP mode.
SETUP menu is displayed on the monitor screen.
2. Select the desired feature using the UP or DOWN buttons.
Each time you press the UP or DOWN button, the arrow
indicator moves up or down.
Move the arrow indicator to the desired feature item.
3. Change the status of the selected feature using the LEFT or RIGHT button.
4. When completed, move the arrow indicator to ‘EXIT’ and press the SET button.
1) Setting up the LENS Select the lens pressing the RIGHT button. On the SETUP menu screen, move the arrow indicator to the lens
using the UP or DOWN button.
Select the desired feature using the LEFT or RIGHT button.
Notes
●You can access the submenu by using SET button.
●For the mode with ’---’, you may not access submenu.
13 14
Operating your camera – SHUTTER SPEED CONTROL①
When DC LENS is selected, press SET button to control
the BRIGHTNESS.
Notes
2) Shutter status and speed control You can control brightness of the screen by the shutter speed. Press the SET button to display the setup menu and move the arrow
indicator to ‘SHUTTER’ using the UP or DOWN button.
Set ‘SHUTTER’ to the desired mode using the LEFT or RIGHT
button.
OFF : Deactivation
AUTO IRIS LENS (DC TYPE) is recommended
15 16
FLK (1/100) : Flicker mode
Operating your camera –SHUTTER SPEED CONTROL ②
MANUAL : When setting the shutter speed manually.
You can select speed from ‘1/60’ to ‘1/200,000’sec
ELC : You can control the BRIGHTNESS.
When completed, press ‘SET’
Notes
Avoid pointing the camera directly at a fluorescent lamp.
When the SHUTTER menu is set to FLK mode, the INTENSIFIER
will not work.
17 18
Operating your camera - BACKLIGHT
3) SLC (Speco Light Compensation) - BACKLIGHT A built-in SR chip provides intelligent light level control to overcome severe Backlight conditions. Press the SET button to display the SETUP menu and move the
arrow indicator to ‘SLC’ using the UP or DOWN button.
SET ‘SLC’ to the desired mode using the LEFT or RIGHT buttons.
OFF LOW MIDDLE HIGH
4) AUTO GAIN (AGC) AGC allows a brighter picture in low light conditions. Higher GAIN level, will yield a brighter screen, but you might notice an increase in noise. Press the SET button to display the SETUP menu and move the arrow
indicator to ‘AGC’ using the UP or DOWN button.
SET ‘AUTO GAIN’ to the desired mode using the LEFT or RIGHT button.
OFF
LOW MIDDLE HIGH
19 20
Operating your camera - WHITE BALANCE
5) WHITE BALANCE (WHITE BAL.)
Press the SET button to display the SETUP menu and move the arrow indicator to ‘WHITE BALANCE’ using the UP or DOWN button.
Set ‘WHITE BAL.’ to the desired mode using LEFT or RIGHT button.
ATW (Auto Tracking White Balance)
: When color temperature is 2400~12000K, select this mode.
(ex. A fluorescent lamp, or outdoors)
MANUAL : To fine adjust, select the Manual mode. You can increase or decrease the red or blue factor while monitoring the difference on the screen. Set to ‘MANUAL’ mode and press the SET button. Increase or decrease the value for RED(R-Gain) and BLUE(B-Gain), watching the color of the picture, and press the SET button when you obtain the best color.
Notes
Proper White Balance may not be obtained under the following
conditions. In these cases select the AWC mode.
-When the scene contains mostly high color temperature objects, such as a blue sky or sunset.
-When the scene is dim.
-If your camera faces fluorescent lamp directly or is installed in an area with constantly changing illumination.
AWC (Auto White Balance Control)
: The white balance is automatically adjusted in a specific environment.
In order to obtain the best result, press the set button while the camera focuses on white paper. If the environment including the light source is changed, you have to adjust the white balance again.
21 22
Operating your camera - DNR

Operating your camera - INTENSIFER

6) REDUCE NOISE( Dynamic Noise Reduction) DNR reduces the video noise on the screen.
Press the SET button to display the SETUP menu and move
the arrow to ‘REDUCE NOISE’ using the UP or DOWN button.
SET ‘REDUCE NOISE’ to the desired mode using the LEFT
or RIGHT button.
OFF : Deactivation
LOW : Low reduction of the noise
MIDDLE : Middle reduction of the noise
HIGH : High reduction of the noise
7) INTENSIFIER Allows you to get clear images with this function under night or low light conditions. Press the SET button to display the SETUP menu and move the
arrow indicator to ‘INTENSIFIER’ using the UP or DOWN button.
SET ‘INTENSIFIER’ to the desired mode using the LEFT or RIGHT
button.
AUTO : When your camera is under night or low-lighting
conditions select this mode. This mode allows the camera to switch into B/W in low light conditions.
OFF : Deactivation
Notes
If you change the ‘GAIN’ menu from AGC-L to AGC-H, sensitivity is
increased as well as noise on the screen.
When the selected ‘GAIN’ menu is OFF, REDUCE NOISE will not work.
23 24
Notes
If you press “auto” button in the Intensifier mode, you can Control the amount of intensification from 2X ~ X128.
Increasing the amount of Intensification results in brighter pictures Under low light conditions, and may increase image lag.
Increasing the amount of intensification may cause image noise which is to be expected as a normal condition..
Operating your camera – CAMERA TITLE
Operating your camera - CAMERA TITLE
8) NEXT PAGE
Press the SET button to display the SETUP menu and move the arrow indicator to ‘NEXT PAGE’ using the UP or DOWN button. SET ‘NEXT PAGE’ to the desired mode using the LEFT or RIGHT button.
(1) CAMERA TITLE Press the SET button to display the SETUP menu and move the arrow
indicator to ‘CAMERA TITLE’ using the UP or DOWN button.
SET ‘ON’ using the LEFT or RIGHT button.
Press SET button to access the SETUP mode.You can enter up to 15 characters.
a. Move the cursor to character-enter location by using the LEFT
or RIGHT button. b. Select the desired character by using the UP or DOWN button. c. Press SET button to confirm the blinking character. The first
character is saved and the cursor in the bottom of the screen
moves to the next position. d. Repeat above steps until you create the full name you want. e. Select the position at which the CAMERA TITLE will be located on
the screen.
-Move the cursor to ‘POS’ and press SET button.
-Select the position by using the 4-directional buttons, then press the SET button to confirm the position.
f. When completed, move the cursor to ‘END’ and press SET button.
Notes
If the CAMERA TITLE feature is set to ‘OFF’, the name will not
be displayed on the monitor.
25 26
Notes
If you make a mistake while entering name
Move the cursor to ‘CLR’, press ‘SET’ button. After erasing the character from right to left, correct the character again.
Operating your camera – COLOR/SYNC
(2) COLOR : You can choose color and B/W mode electronically. Press the SET button to display the setup menu and move the arrow
indicator to ‘COLOR’ using the UP and DOWN button.
SET ‘COLOR’ to the desired mode using the LEFT or RIGHT button.
COLOR : The camera will always display a color picture
AUTO : The camera will switch into the B/W mode under
low light conditions.
Notes
OSD key may not work for 3 seconds when
COLOR/BW mode is changed.
(3) SYNC : Two SYNCHRONIZATION modes are available INTERNAL and
EXTERNAL LINE-LOCK.
Press the SET button to display the setup menu and move the arrow indicator
to ‘SYNC’ using the UP and DOWN button.
SET to the desired mode using the LEFT or RIGHT button.
INT : Internal synchronization
L/L : If you choose ‘L/L’, you can adjust the desired phase.
-Press the SET button.
-You can adjust the desired phase from 0 to 270.
Notes
When it used in AC power, L/L mode can be used.
In 12V DC, the SYNC menu defaults to ‘Internal.
27 28
Operating your camera – MOTION DETECTION
(4) Whenever your camera detects motion, THE WORDS “motion detected’
will appear on the screen.
Press the SET button to display the setup menu and move the arrow
indicator to ‘MOTION’ using the UP and DOWN button.
SET ‘MOTION’ to the desired mode using the LEFT or RIGHT button.
OFF : Deactivation
ON : MOTION. activated
-Press SET button.
-Move the arrow indicator to ‘AREA SET’ using UP and DOWN button, and then press the SET button.
- Set the areas you want to observe.
29
Max. Min.
30
Operating your camera - PRIVACY Operating your camera - MIRROR
(5) PRIVACY : To mask an area that you want to be private. Press the SET button to display the setup menu and move the arrow
to ‘PRIVACY’ using the UP and DOWN button.
SET ‘PRIVACY’ to the desired mode using the LEFT or RIGHT button.
OFF : Deactivation
(6) REVERSE Press the SET button to display the setup menu and move the
arrow indicator to ‘REVERSE’ using the UP and DOWN button.
SET ‘REVERSE’ to the desired mode using the LEFT or RIGHT
button.
OFF : Deactivation
ON : Reverse the image RIGHT or LEFT.
ON : PRIVACY mode activated
-Press the SET button.
-Move the arrow to the area you want to mask.
-Set ‘ON’ using LEFT or RIGHT button.
-Press the SET button and then set the area’s bounds as for Motion detection.
31
32
Operating your camera – DETAIL
Operating your camera - RESET/RETURN
(7) DETAIL Press the SET button to display the setup menu and move the arrow
indicator to ‘DETAIL’ using the UP and DOWN button.
SET ‘DETAIL’ to the desired mode using the LEFT or RIGHT button.
OFF : Deactivation
ON : DETAIL control mode (level 0~31)
When the level is up, the sharpness will increase. Control this level to get your best picture quality. If the level is too high, you can get an unnatural image with video noise.
(8) DEFAULT : Use to reset your camera to FACTORY DEFAULT
SETTING.
(9) PAGE 1 : Save the setting of NEXT PAGE function, and then
move to SET UP menu.
33
34
Troubleshooting
If you have trouble operating your camera, refer to the following.
Nothing appears on the screen.
The image on the screen is dim.
The image on the screen is dark.
The camera is not working properly,
and the surface of the camera is not.
MOTION DETECTION function is not active.
SolutionProblem
Check that the power cord and line connection
between the camera and monitor are proper.
Check that you have properly connected the
VIDEO cables.
Is the lens stained with dirt? Clean your lens with
a soft, clean cloth.
Adjust the monitor as required.
If the camera is exposed to very strong light
change the camera position.
Adjust the lens’ focus properly.
Adjust the contrast feature of the monitor.
If you have an intermediate device, set the 75/Hi-z properly.
Check that you have properly connected
the camera to an appropriate power source.
Have you set ‘MOTION DET.’ menu to off?
Have you set ‘MD ARAEA’ properly
Problem
The color of the picture is not matched.
The image on the screen flickers.
L/L mode isn’t able to be selected.
Solution
Check that you have properly set the ‘WHITE BAL’ menu
Is the camera facing to direct sunlight or fluorescent lighting? Change the camera position.
Have you connected your camera to DC power
source? Connect it to AC power source.
35
36
SPECIFICATIONS
DIMENSIONS
ITEM
LENS Type
HT – INTB1
HT – INTB2
DC 12V & AC 24v ( Dual Voltage )Power Source
280mA(DC) / 3.8W(AC)Power Consumption
1/3”, SONY SUPER HAD CCD, 410,000 pixelsI mage Sensor
811(H) x 508(V) , 1/3” CCDTotal Pixels
768(H) x 494(V) , 1/3” CCDEffective Pixe ls
HT – INTB1 : DC VARIFOCAL AUTO IRIS 3mm~9mm
HT – INTB2 : DC VARIFOCAL AUTO IRIS 5mm~50mm
1 : 1.3 ~2.0Maximum Aperture Ratio
2 : 1 Interlaced 525 Lines / 60 Fields / 30 FramesScanning System
Internal / Line Lock selectableSynchronization
1.0V [p-p] NTSC Composite, 75/ BNC ConnectorVideo Output
530 TV LineResolution
AGC-L, AGC-H, OFF selectableGain Control
1/60 ~ 1/200,000 secElectric Shutter Speed
Built-in ( selectable limit ~ X128)INTENSIFIER
ATW / AWC / MANUALWHITE BALANCE
0.003Lux (intensifier) 0.3Lux(sh)Min. Illumination
50dB (Weight On)S/N ( Y signal)
OFF / LOW / MIDDLE / HIGHREDUCE NOISE
MD1 / MD2 / OFFMotion Detection
Built - inOn Screen Display ( O.S.D )
ON / OFF (4 Programmable Zone)PRIVACY Function
-29~ +50(-20~120℉)Operational Temperature
to 95% RHOperational Humidity
* SIDE VIEW : HT-INTB1
82
Speco technologies
* SIDE VIEW : HT-INTB2
92
Speco technologies
156
190
37
38
WARRANTY
39
Loading...