Speco Technologies HTINT650S, HTINT650W User Manual

◐NOTES

1. You can install the camera indoors or outdoors.

2. Be careful not to scratch the lens or dome cover.

3. Use 1Amp power supply at 12V DC or 24V AC.

◐FEATURES

1. IP67 (Waterproof)

2. Construction Body : Aluminum, Dome : Polycarbonate

3. (Optional) Wall, Ceiling and pole mounts available

4. 25M range visible in total darkness with 24pcs o

IR LEDs (depends upon scene reflection)

5. Side control board for easy function adjustment

6. Dual power (12V DC or 24V AC) operation

◐DIMENSION

◐HOW TO INSTALL

1. Camera installation

(1) Fix the camera with the supplied screws on

ceiling or wall mount.

(2) Please refer to '3. Camera angle adjustment' regarding

adjust camera angle.

(3) Lens adjustment

fter opening the LED cover,

①By turning the "Tele-Wide" knob, you can access a

range of focal lengths within specified limits.

②By turning the "Near-Far" knob, you can set the

focus toward an object.

(4) Reassemble the camera.

HTINT650S, HTINT650W

2. Pipe application

(1) Remove the screw for fixing a cable on the bottom

of the base. (2) Open the DOME COVER. (3) Remove the TAP COVER and place the cables there. (4) After distributing cables, use the TEPLON tape to

wipe the pipe. (5) Attach the pipe to the base. <Caution> If you don't wipe TEFLON tape on pipe, it

might cause water intrusion issues.

3. Camera angle adjustment

(1) Pan adjustment : Grasp the disk of camera and

adjust direction to the right or left(-160˚~ 190˚) (2) Tilt adjustment : Grasp the LED cover of camera and

adjust direction to up or down(6˚~ 90˚) (3) Roll adjustment : Grasp the camera holder and

then rotate(-178˚~ 178˚) <Caution> If you try to adjust the camera out of limited

angle, it might cause damage to camera.

◐SPECIFICATION

Model No. HTINT650S, HTINT650W

Image Sensor

Effective Pixel 768(H) X 494(V) PIXEL

Cell Size

Scanning System 2 : 1 Interlace

Sync. Type Internal / Line lock(24V AC)

OSD Multi-language

WDR Set SSDR / BLC / HLC / OFF

Resolution Color : 600 TV-Line, B/W : 700 TV-Line

S/N Ratio 52dB(AGC OFF, Weight ON)

Min. Illumination

Color Temp.

Shutter 1/60 ~ 1/120,000sec

Intens ifier AUTO / FIXED / OFF(x2 ~ x512 selectable)

Gain Control LOW / HIGH / OFF

Speco DNR OFF / ON(1 ~ 32 Level adjustable)

V Motion ON / OFF(8 Zone, Alarm output)

Privacy ON / OFF(12 Zone)

Mirror H / V / BOTH / OFF

Clarity ON / OFF(Level adjustable)

D&N ICR(COLOR / Black&White / AUTO)

Stabilize ON / OFF

Digital Zoom ON(x16) / OFF

DPC 256 point(Even 128 point, ODD 128 point)

Power Supply Regulated 12V DC or 24V AC

Current Consumption 150mA(LED OFF), 500mA(LED ON)

Operation Temp. -20 to 122

Dimension Ø150 x 98.6(H)mm

Weight 1.76Ibs

※The specification is subject to change without any

prior notice to improve the quality.

1/3" SONY SUPER HAD CCD

6.35

㎛

(H) X 7.4㎛(V)

LED ON : 0 Lux(25M Range) LED OFF : 0.0005 Lux(Color Sense-up),

0.0002 Lux(B/W Sense-up) ATW(1,700°K ~ 11,000°K) / AWC / MANUAL / OUTDOO R / INDOOR

Ⅱ

◐FUNCTIONS

1. Setup for camera functions

①ENTER :

- Push the lever : Used to access the menu and confirm selection.

- Push the lever for one second : Open the menu or close the menu.

②Up, ③Down :

Used to move the cursor to up or down.

④Left, ⑤Right :

Used to move the cursor to left or right and change the value.

⑥EXT-VIDEO :

Extra video output terminal for installation. Plug your test monitor in here. The cable is option.

2. Camera function setting

Function

Select

setting

DC IRIS ADJUST LENS

MANUAL

BRIGHT-

NESS

E -

SHUTTER

AUTO

GAIN

EXPOSURE

SENS-

RETURN

*Notes : If the AGC is off, the sense-up function is not

available. As the sense-up level increases, an after-

image will appear. ATW Color temperature 1,700~11,000°K OUT-

DOOR INDO OR Color temperature 4,500~8,500°K

COLOR

MANUA

TEMP

WDR SET

SLC SET

SPECO DNR

DAY & NIGHT

Page 2 Please refer to "Page 2"

EXIT

AWC SET

OFF Deactivates function

SLC

HLC

ON Level

OFF Deactivates function

*Notes : If the AGC is off, the DNR function is not available

AUTO

EXT

COLOR Fixed at color(LED OFF)

B/W

*Notes : If the AGC is off, this function is unavailable

SAVE Save the value and exit menu NOT

SAVE DEFAU LTS

Page 1

Sub

BRIGHT NESS, IRIS SPEED, FOCUS ADD.

BRIGHT NESS

MANUAL

FLK,

- - -

OFF, LOW, HIGH

OFF, AUTO

Color temperature 1,700~11,000°K

→

LEVEL, TOP, BOTTOM, LEFT, RIGHT LEVEL, LIMIT, MASK COLOR, MASK TONE, TOP, BOTTO M, LEFT, RIGHT

BURST MODE COLOR

→

B/W,

→

B/W COLOR, RETURN

BURST MODE (OFF/ON), RETURN

Exit the main menu without sav e

Summary

Adjust the brightness of the screen (Range : 1~70, Default : 25) Adjust the Iris spee d of the DC lens (Range : 1~50, Default : 3) Focus addition : To adjust the lens focus correctly Manual mode is not recommended using built-in the DC Lens(Default :

25) Brightness ADJ. : Adjust the brightness of the screen when using the DC lens(Range : 1~70, Default : 25)

Auto setting is not selectable when selected DC Lens

OFF : Deactivates function LOW : Auto selection between

5.3dB and 32dB HIGH : Auto selection between

5.3dB and 37dB(You can not use the DIS, Day&Night when AGC is off) OFF : Deactivates function AUTO : Using sense up when it is low luminance(x2~x512 selectable) Save the value then move back to previous menu

Adjust the Red or Blue values to shift the color of the screen Find the optimal white balanc e for current luminance environment (The camera focus must towards to white paper)

Wide dynamic range function(1 ~15 level selec-table, Default : 8)

User programmable SLC zone and compensation level

Removed HIGH LIGHT, It enable us to watch license plate clearly

Reduce noise in low illumination (Reduction level is selectable, Default : 20)

↔

Day : Color (Switching time & speed adjustable)

Change the color ternal signal (Not availabl e)

Fixed at B/W(LED ON)

Reset the camera setup value to the factory default

Night : B/W

↔

B/W by ex-

HTINT650S, HTINT650W

Speci al

Select

setting

V-REV Set a vertical image inversion

H-REV Set a horizontal image inversion DIGI-

ZOOM FONT COLOR

ADJUST

CLARITY

RETURN

LCD

MONITOR

USER

CRT

OFF No title displays on the screen CAM TITLE

INT Internal Sync with 12V DC power SYNC

TYPE

SENSITI

VITY

AREA

MODE

SEL

POS

XPOS MOTION

YPOS

FILL →

SET

RETURN

*Notes : If the camera detected motion, "MOTION

DETECTED" will appear on the screen

AREA

SEL

AREA

MODE

MASK

COLOR

PRIVACY

MASK

TONE

TOP

BOTTOM

LEFT

RIGHT

RETURN

STABI

ON,

-LIZE

OFF

LAN-

Select language

GUAGE

PAG E 1

ㆍThe " " icon ap peared with desired function, press the set

button to move sub menu.

ㆍThe "---" icon appeared with function that is una-vailable

according to function setting.

Sub

GAMMA, PED LEVEL, COLOR GAIN, DEFAULT SET GAMMA, PED LEVEL, COLOR GAIN, DEFAULT SET PED LEVEL, COLOR GAIN, DEFAULT SET

AREA1~ AREA8

OFF, ON

L_TOP, R_TOP, L_BOTTOM, R_BOTTOM

AREA1~ AREA12

ON, OFF

GREEN, RED, BLUE, BLACK, WHITE, GRAY

1~10

Page 2

Summary

Max 16x digital zoom available (Default : X1.0) Change the color of OSD (Default : Blue, 5 color is available) The image outline will be strong and clear according to sharpness level increasing(Default : 13) If this function is Off, it may looks like un-focused Save the value then move back to previous menu

You can change the settings value of video appropriate to your monitor

Display the camera's title on the screen(Max. 15character, position adjustable)

Setting the phase is selectable w hen used 24V AC(Dual power only) When sensitivity number is high, also motion detection sensitivity will increase Determines whet her to use the MD area selected in SENSITIVITY

Determines which of the 4 vertices of each MD area is to be used

Determines the coordinate of the horizontal axis for SEL POS Determines the coordinate of the vertical axis for SEL POS Fill the color in selected area(The color of filling is sequentially selected as brown, orange, blue, cyan, yellowis h green, yellow, magenta and red.) Save the value then move back to previous menu

Make a zo ne for your pr ivacy You can select privacy zone up to 12 area

Save the value then move back to previous menu

This function can be mitigates image movement from external factors

Select this to save the special menu settings and return to the main menu

Speco Technologies is constantly

developing product improvements. We

reserve the right to modify product design

and specifications without notice and

without incurring any obligation.

Rev. 7/7/10.

3B15011B