Speco x20 HD-SDI PTZ Outdoor User Manual

Ver. 0.5 / 2011.03

User’s Manual

All-In-One Camera

HD-SDI PTZ Outdoor

Safety Information

2

This symbol indicates that dangerous voltage
consisting a risk of electric shock is present within
this unit.

Warning Precaution

This exclamation point symbol is intended to alert the
user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

:

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

To prevent damage which may result in fire or electric shock
hazard, do not expose this appliance to rain or moisture.

Be sure to use only the standard adapter that is specified in
the specification sheet. Using any other adapter could cause
fire, electrical shock, or damage to the product.

Incorrectly connecting the power supply or replacing battery
may cause explosion, fire, electric shock, or damage to the
product.

Do not connect multiple cameras to a single adapter.
Exceeding the capacity may cause abnormal heat generation
or fire.

Securely plug the power cord into the power receptacle.
Insecure connection may cause fire.

When installing the camera, fasten it securely and firmly.
A falling camera may cause personal injury.

Do not place conductive objects (e.g. screw drivers, coins,
metal things, etc.) or containers filled with water on top of
the camera. Doing so may cause personal injury due to fire,
electric shock, or falling objects.

Do not install the unit in humid, dusty, or sooty locations.
Doing so may cause fire or electric shock.

If any unusual smells or smoke come from the unit, stop
using the product. In such case, immediately disconnect the
power sorce and contact the service center. Continued use
in such a condition may cause fire or electric shock.

If this product fails to operate normally, contact the nearest
service center. Never disassemble or modify this product in
any way.

When cleaning, do not spray water directly onto parts of the
product. Doing so may cause fire or electric shock.

WARNING

WARNING

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

Precautions

Operating

• Before using, make sure power supply and others are

properly connected.

• While operating, if any abnormal condition or malfunction

is observed, stop using the camera immediately and then

• contact your Special dealer.

Handling

• Do not disassemble or tamper with parts inside the camera.

• Do not drop or subject the camera to shock and vibration as

this can damage camera.

• Care must be taken when you clean the clear dome cover.

Especially, scratch and dust will ruin your quality of camera.

Installation and Storage

• Do not install the camera in areas of extreme temperature,

which exceed the allowable range.

• Avoid installing in humid or dusty places.

• Avoid installing in places where radiation is present.

• Avoid installing in places where there are strong magnetic

elds and electric signals.

• Avoid installing in places where the camera would be subject

to strong vibrations.

• Never expose the camera to rain and water.

3

1. Read these instructions. - All these safety and operating instructions should be read before the product is operated.

2. Keep these instructions. - The safety, operating and use instructions should be retained for future reference.

3. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.

4. Follow all instructions. - All operating and use instructions should be followed.

5. Do not use this apparatus near water. - For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a

wet basement; near a swimming pool; etc.

6. Clean only with dry cloth. - Unplug this product from the wall outlet befor cleaning. Do not use liguid cleaners.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. - Slots and

openings in the cabinet are provided for ventilation, to ensure reliable operation of the product, and to protec it
from over-heating. The openings should never be blocked by placing the product on bed, sofa, rug or other similar
surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided and the manufacturer’s unstructions have been adhere to.

8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including ampliers)

that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does not t into your outlet, consult an
electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and

the point where they exit from the apparatus.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with cart, stand, tripod, bracket, or table specied by the

manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid
injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged

in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.

Important Safety Instructions

4

Disposal of Your Old Appliance

1. When this crossed-out wheel bin symbol is attached to a product it mean the product is covered by
the European Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of separately form the municipal waste
stream via designated by the government or the local authorities.

3. The correct disposal of your old appliance will help prevent potential negative consequences for
the environment and human health.

4. For more detailed information about disposal of your old appliance, please contact your city oce,
waste disposal service or the shop where you purchased the product.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user

will be required to correct the interferenece at his own expense.

Contents

5

6

7

8

Product & Accessories

Parts Name & Functions_Appearance

Parts Name & Functions_Inside

4 Precautions

1. Introduction

9

13

15

Installation

DIP Switch Setup

Cabling

2. Installation

17

18

19

20

21

22

23

25

26

27

28

Check Points before Operation

OSD -

ROOT MENU & SYSTEM INFORMATION

OSD -

MOTION SETUP

OSD -

FUNCTION SETUP > PRESET SETUP

OSD -

FUNCTION SETUP > SCAN SETUP

OSD -

FUNCTION SETUP > PATTERN SETUP

OSD -

FUNCTION SETUP > GROUP SETUP

OSD -

CAMERA SETUP > WB SETUP

OSD -

CAMERA SETUP > AE SETUP

OSD -

CAMERA SETUP > OTHER SETUP

OSD -

SYSTEM SETUP

3. OSD Menu

29 Dimensions

4. Specification

6

Product & Accessories

Introduction -

1

All-In-One Camera

Manual CD

Hexagonal Wrench

Product Accessories

Quick Manual

7

Part Name & Functions_Appearance

Introduction -

1

3

4

Dome Safety Wire

Prevents the dome cover from falling.

Dome Cover

Do not detach protection lm from dome cover before
finishing all installation process to protect dome cover
from scratches or dust. In the dome cover, there are fan
and heater to remove moisture on the bubble dome.

1

2

Sunshield & Upper Housing

Sunshield protect bubble dome cover from the sun rays and
rain fall. In the sunshield, there is the upper housing which
will contain accommodate PTZ mechanism. Also, the upper
housing will be connected to both mounting brackets and
dome cover.

PTZ Mechanism

Control the PTZ operations of the camera.

1

Sunshield & Upper Housing

2

PTZ Mechanism

3

Dome Safety Wire

4

Dome Cover

8

Part Name & Functions_Inside

Introduction -

1

6

7

8

9

10

2nd Video Output Port

Video out check the screen during installation.

ID Setup Switch

Specify the camera ID.

Communication Setup Switch

Set the transfer rate and protocols.

RS-485 Port

Used for RS-485 communications.

Power Port

Connect the power source here.

1

2

3

4

5

BNC Coxial Cable

Connects to video output device such as monitor using the
BNC coaxial cable.

Alarm Output Port

It connects to the alarm lights, siren or lamps, and it is
activated according to the OSD menu or ‘Setup’ on the Web

-viewer setting.

Alarm Input Port

It connects to IR sensor, IrDA sensor or door switch. If the
sensor is activated, it can activate to move camera to the
specic angle and to connect the alarm device.

Fan

Defrosts the dome cover and removes moisture.

Heater

Defrost the dome cover in a low temperature by increasing
the internal temperature of the housing.

Alarm Output Port

Alarm Input Port

Fan

Heater

ID Setup Switch

Communication
Setup Switch

RS-485 Port

Power Port

2

nd Video

Output Port

2

3

4

5

6

7

1

Video Coxial Cable

8

10

9

9

Installation

Installation -

2

5

You have to detach the PTZ mechanism from the upper
housing to plug the connector of cable. When detach PTZ
mechanism, pressing down and holding up the black
handles in both sides of PTZ mechanism.

6

[1] Wind the water proof tape on the pipe of upper housing.
[2] Hooking the safety wire on the hole of pipe.
[3] Attach the upper housing to wall mount bracket by
turning it at least seven turns.

To fix the upper body orientation, turn the handle of
double nuts to clockwise tightly.

[2]

[1]

[3]

10

Installation

Installation -

a

b

c

d

e

f

2

Connect each of the following cables to the applicable port
and set the DIP switch to congure the camera ID,
communication protocol.

Alarm Output Port
Alarm Input Port
DIP Switch for Camera ID Setup
DIP Switch for Communication
RS-485 Port
Power Port

Refer to 13, 14 page for detail DIP switch setting.
Refer to 15, 16 page for detail cablings.

a

b

c

d

e

f

Make sure that the dome cover is connected rmly to the
safety wire.

8

7

11

Installation

Installation -

2

8

7

To lock the PTZ mechanism to the upper housing, press the
two black handles till it sounds snap.

Plug the connector of cable from junction box into properly.
After checking the orientation of one touch connector in the
upper housing, press the PTZ mechanism into hook in the
upper housing.

12

Installation

Installation -

2

10

9

Close the dome cover. Care must be taken to locate dome
cover by matching the ‘Arrow Mark’.

Tighten four screws on the dome cover in sequence as
shown in the picture.

To maintain the best sealing, the torque of each screw
must be in the range between

0.5 ~ 1.0 N·m(0.3 ~ 0.73 lbf·ft).

Arrow Mark

Arrow Mark

13

DIP Switch Setup

Installation -

2

Before installing the camera, you should set
the DIP switch to configure the camera ID,
communication protocol.

Interface Board

1. Communication Protocol Setup

Select the appropriate protocol with DIP switch combination.

- If you set the protocol as ‘Auto’ protocol, camera

will

automatically recognize PELCO-D or PELCO-P protocol.

-

If you want to control using DVR or system keyboard,

their
protocol must be identical to camera. Otherwise, you can
not control the camera.

- If you change camera protocol by changing DIP switch, the
change will be eective after you reboot the camera.

Protocol Setup Baud Rate Setup

RS-485

Termination Resistor

ON

8J

21 3 4 5 6 7 8

1

Auto - Factory Default

ON

8J

21 3 4 5 6 7 8

2

ON

8J

21 3 4 5 6 7 8

PELCO-D

3

ON

8J

21 3 4 5 6 7 8

PELCO-P

4

5

6

7

SAMSUNG

ON

21 3 4 5 6 7 8

Panasonic

8J

ON

21 3 4 5 6 7 8

GE(Kalatel)

8J

ON

21 3 4 5 6 7 8

AD(American Dynamics)

ON

8J

21 3 4 5 6 7 8

14

DIP Switch Setup

Installation -

2

2. Communication Baud Rate Setup

Select the appropriate baud rate with DIP switch combination.

4. Camera ID Setup

ID number of camera is set using binary number.
The example is shown below.

Interface Board

1

2

3

4

5

ON

8J

21 3 4 5 6 7 8

2400 BPS - Factory Default

ON

8J

21 3 4 5 6 7 8

4800 BPS

ON

8J

21 3 4 5 6 7 8

9600 BPS

ON

8J

21 3 4 5 6 7 8

19200 BPS

38400 BPS

ON

8J

21 3 4 5 6 7 8

3. RS-485 Termination Resistor

- Pin 8 is used for on/off of RS-485 termination.

- Normally, it must be off state.

- Especially, when you have trouble with long daisy chain style
connection, turn on this termination switch of the last camera.

ON

8J

21 3 4 5 6 7 8

Pin 1 2 3 4 5 6 7 8

1 2 4 8 16 32 64 128ID Value

ex) ID=5

ex) ID=10

on

off

offonon

off

offonoff

off

off

off

off

off

off

off

- If you want to control a certain camera, you must match the
camera ID with ‘CAM ID’, setting of DVR or keyboard controller.

- ID number of the camera is set using binary number.

- The range of ID is 0~255.

- Factory default of camera ID is 1.

- Camera ID will be effective without rebooting the camera.

15

2

Cabling

Installation -

1

3

2

RS-485 Communication (DVR/Keyboard)

For PTZ control, connect this line to keyboard and DVR.
To control multiple cameras at the same time, RS-485
communication lines of them are connected in parallel as
shown below.

Keyboard Controller/DVR

RS-485

#1 #2 #n

~

Video Output

Connects to video output device such as monitor using the
BNC coaxial cable.

Power Connection

Please, check the voltage and current capacity of rated
power carefully.

Coil up the power cable to the Ferrite Core. It will control the
electromagnetic waves of Power Cable.

Rate Power PoE

Current

Consumption

AC 24V 802.3at class 4Heater Off: 24W Heater On: 55W

RS-485
(Keyboard Controller/DVR)

3

RS-485

Video Output

1

AC 24V

F.G

Power

2

16

Cabling

Installation -

2

OUT1

OUT2

OUT3

OUT4

6

5

Alarm Output

There are 4 alarm outputs and all of them are relay contact
type. Therefore, you do not have to care about polarity,
AC/DC, and isolations between channels. Care must be taken
for the power capacity of relay contact written above.

Out Out

N.C

Activation

Activation

N.O

In 2

COM

In 2

COM

In 2

COM

In 2

COM

It is noted that short circuit between GND and Input pin
means alarm activation.

Sensor Input/Sensor

If you want to use alarm input, the types of sensor must be
selected in OSD menu. The sensor types are ‘Normal Open’
and ‘Normal Close’. If sensor type is not selected properly,
the alarm can be activated reversely.

COM

In 1

ALARM INPUT

GND1

2 3 4 5 6 7 8

Alarm Input/Sensor

ALARM INPUT

GND1

2 3 4 5 6 7 8

COM

In 1

In 8

Alarm Output

Alarm Input

Alarm Output

6

5

OUT1

OUT2

OUT3

OUT4

1. Before power is applied, please check the cables carefully.

2. The camera ID of the controller must be identical to that of the camera to be controlled. The camera ID can be check in the
system information of OSD menu.

3. If your controller supports multi-protocols, the protocol must be changed to match to that of the camera.

4. If you changed camera protocol by changing DIP switch, the change will be eective after you reboot the camera.

5. Since the operation method can be dierent for each controller available, refer to the manual for your controller if camera
cannot be controlled properly.

Check Points before Operation

Preset and Pattern Function Pre-check

- Check how to operate preset, pattern, scan and group
function with keyboard controller/DVR in advance to
operate camera function using them.
(Refer to your system keyboard manual)

Start OSD Menu

Using the OSD menu, preset, pattern, scan, group and alarm
input function can be configured for each application.
Enter ‘Preset key + 95’.

17

Check Points before Operation

OSD -

1

2

3

18

ROOT MENU & SYSTEM INFORMATION

OSD -

3

ROOT MENU

<SYSTEM INFORAMTION>

Shows information and current configuration.

<MOTION SETUP>

Setup for motion related settings.

<FUNCTION SETUP>

Setup for various functions such as preset, scan, pattern, group and
schedule.

<CAMERA SETUP>

Configure camera related functions and data.

<SYSTEM SETUP>

Configure for basic system setup.

SYSTEM INFORMATION

FIRMWARE VER

Shows the current firmware version.

HD-SDI

Shows the current resolution of HD-SDI.

PROTOCOL

Shows the current PTZ control protocol.

BAUD RATE

Shows the current baud rate of the PTZ control.

CAMERA ADDRESS

Shows the current camera ID of the PTZ control.

11

11

ROOT MENU

====================================================

<SYSTEM INFORMATION>
<MOTION SETUP>
<FUNCTION SETUP>
<CAMERA SETUP>
<SYSTEM SETUP>

EXIT

<SYSTEM INFORMATION>

====================================================

FIRMWARE
HD-SDI
PROTOCOL
BAUD RATE
CAMERA ADDRESS

BACK
EXIT

v0.52_110311 [18]
1920x1080i60
Pelco-D
2400
1

19

MOTION SETUP

OSD -

11

2

3

4

2

MOTION SETUP

Setup the general functions of pan/tilt motions.

PWR UP ACTION

This function enables to resume the last action executed before power
down. Most of actions such as preset, pattern, scan and group are
available for this function but jog actions are not available to resume.

JOG MAX SPEED

Sets maximum jog speed. Jog speed is inversely proportional to zoom
magnification. As zoom magnification goes up, pan/tilt speed goes down.

JOG DIRECTION

If you set this to ‘NORMAL’, the view in the screen is moving same
direction with jog tilting. If ‘INVERSE’ is selected, the view in the screen
is moving reversely.

<ALARM INPUT SETUP>

Moves to ‘ALARM INPUT ACTION’ screen.

ON / OFF

30/SEC ~ 150/SEC

NORMAL / INVERSE

ALARM INPUT SETUP

If an external sensor is activated, camera will move to
corresponding action.

3

ALARM INPUT SETUP - Type Setup

1) Move joystick up/down to set alarm type.

2) Move joystick right to set alarm action.

ALARM INPUT SETUP - Alarm Action Setup

1) Move joystick up/down to set the action(HOME, PRESET,
SCAN, PATTERN, GROUP) and number.

2) Move joystick left/right to move the focus to set alarm type,
function name and function number.

3) By pressing near key, save the current setting.

4

Alarm Number

Alarm Type

- Sets sensor input type.

- Refer page 14 for more detailed information.

Alarm Action

Assign counter-action to each alarm input. Among 149 actions, choose
the action as explained below.

1 ~ 8

N.O(Normal Open) / N.C(Normal Close)

NOT USED / HOME / PRESET 1~255 /
SCAN 1~8 / PATTERN 1~4 / GROUP 1~8

<MOTION SETUP>

====================================================

POWER UP ACTION
JOG MAX SPEED
JOG DIRECTION

<

ALARM INPUT SETUP>

BACK
EXIT

ON
100/SEC
NORMAL

3

‘<ALARM INPUT SETUP>’ select
and press the ‘NEAR’ Key

<ALARM INPUT SETUP>

====================================================

ALARM 1
ALARM 2
ALARM 3
ALARM 4
ALARM 5
ALARM 6
ALARM 7
ALARM 8

BACK
EXIT

NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED

N.O
N.O
N.O
N.O
N.O
N.O
N.O
N.O

<ALARM INPUT SETUP>

====================================================

ALARM 1
ALARM 2
ALARM 3
ALARM 4
ALARM 5
ALARM 6
ALARM 7
ALARM 8

BACK
EXIT

NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED

N.O
N.O
N.O
N.O
N.O
N.O
N.O
N.O

<ALARM INPUT SETUP>

====================================================

ALARM 1
ALARM 2
ALARM 3
ALARM 4
ALARM 5
ALARM 6
ALARM 7
ALARM 8

BACK
EXIT

NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED

N.C
N.O
N.O
N.O
N.O
N.O
N.O
N.O

Select ‘Alarm Number’
by move joystick up/down.
And press the ‘NEAR’ key

Select ‘Alarm Type’
by move joystick up/down.
And move joystick right.

Select ‘Alarm Action’
by move joystick up/down.
And press the ‘NEAR’ key to save.

20

FUNCTION SETUP > PRESET SETUP

OSD -

1

2

3

<FUNCTION SETUP>

====================================================

<PRESET SETUP>
<SCAN SETUP>
<PATTERN SETUP>
<GROUP SETUP>

BACK
EXIT

<PRESET SETUP>

====================================================

PRESET NUMBER

<

EDIT SCENE>
CLEAR PRESET
ALARM OUT

BACK
EXIT

1

CANCEL

- - - -

<EDIT SCENE>

====================================================

MOVE TO TARGET POSITION
[NEAR:SELECT/FAR:CANCEL]

3

Select ‘<PRESET SETUP>’
and press the ‘NEAR’ key

After define the ‘PRESET NUMBER’,
select ‘<EDIT SCENE>’
and press the ‘NEAR’ key

FUNCTION SETUP

Configure 4 special functions with this menu.

1

PRESET SETUP

255 presets from the number 1 to 255 can be assigned excluding
preset 95, 131~134, 141~148, 151~158 reserved for menu.

PRESET NUMBER

Selects the preset number to edit.

<EDIT SCENE>

Define the current preset scene position(i.e. PTZ).

CLEAR PRESET

Deletes current preset data.

ALARM OUT

State of four alarm outputs can be freely controlled in conjunction
with preset run. The character ‘ - ’ means off state and the number
representing each bit means on.
Ex) If it is set to be ‘ - 2 3 - ‘, output relay 2, 3 will be on and 1, 4 will be
be off, when you run this preset.

1 ~ 255

CANCEL / OK

- - - - / 1234

EDIT SCENE

1) By PTZ controling, move camera to desired position.

2) By pressing the ‘NEAR’ key, the save current PTZ data.

3) If you want cancel the editing, press the ‘FAR’ key.

3

2

21

FUNCTION SETUP > SCAN SETUP

OSD -

1

2

<FUNCTION SETUP>

====================================================

<PRESET SETUP>
<SCAN SETUP>
<PATTERN SETUP>
<GROUP SETUP>

BACK
EXIT

<SCAN SETUP>

====================================================

SCAN NUMBER
FIRST POSITION
SECOND POSITION
SCAN SPEED
CLEAR SCAN

BACK
EXIT

1
NOT USED
NOT USED
30/SEC
CANCEL

3

Select ‘<SCAN SETUP>’
and press the ‘NEAR’ key

1 ~ 8

PRESET 1 ~ 255 / NOT USED

PRESET 1 ~ 255 / NOT USED

1/SEC ~ 180/SEC

CANCEL / OK

2

SCAN NUMBER

Selects the scan number to edit.

FIRST POSITION

Set up the 1st position for scan function.

Undefined preset cannot be assigned as position. If you press ‘NEAR’
key when the selected undefined preset, the preset will returned to
previous position(Available preset or ‘NOT USED’).

SECOND POSITION

Same as the 1st position setup.

SCAN SPEED

Sets the scan speed.

CLEAR SCAN

Deletes the current scan data.

1st POS.

1. CW direction

2. CCW direction

2nd POS.

SCAN SETUP

Up to 8 scans are available, which makes the camera to move
slowly between two preset positions.

When scan function runs, the camera moves from the preset
assigned as the 1st pos. to the preset assigned as the 2nd pos.
in CW(Clockwise) direction. Then camera moves from the preset
assigned as the 2nd pos. to the preset assigned as the 1st pos.
in CCW(Counterclockwise) direction. Then, it continues to move
from the 1st pos. to the 2nd pos. back and forth.

If the 1st POS. = the 2nd POS.

In case that the preset assigned as the 1st pos. is same as the
preset assigned as the 2nd pos., camera turns on its axis by 360°
in CW direction and then it turns on its axis by 360° in CCW direction.

If one preset is not defined between the 1st POS. and the 2nd POS.

If case that a position assigned is ‘NOT USED’, camera turns on
its axis by 360° in CW direction from the preset which is
‘NOT USED’ and then it turns on its axis by 360° in CCW direction.

22

FUNCTION SETUP > PATTERN SETUP

OSD -

1

2

<FUNCTION SETUP>

====================================================

<PRESET SETUP>
<SCAN SETUP>
<PATTERN SETUP>
<GROUP SETUP>

BACK
EXIT

<PATTERN SETUP>

====================================================

PATTERN NUMBER

<

EDIT PATTERN>
CLEAR PATTERN

BACK
EXIT

1

CANCEL

3

Select ‘<PATTERN SETUP>’
and press the ‘NEAR’ key

3

4

2

PATTERN SETUP

Pattern function is that a camera memorizes the path (mostly
curve path) by joystick of controller for assigned time and
revives the path exactly as it memorized.

4 patterns are available and max. 1000 communication
commands can be stored in a pattern.

PATTERN NUMBER

Select pattern number to edit.

<EDIT PATTERN>

Starts editing pattern.

CLEAR PATTERN

Deletes data in the current pattern.

1 ~ 4

CANCEL / OK

EDIT PATTERN - Select the Position

1) By using joystick, move to the start position with appropriate
zoom.

2) To start the pattern recording, press the ‘NEAR’ or ‘ENTER’ key.

3) To exit this menu, press the ‘FAR’ key.

EDIT PATTERN - Records

1) Move the camera with joystick of the controller or run preset
function to memorize the path (mostly curve path) in a
selected pattern.

2) The total memory size and the rest memory size is displayed
in the form of bar.

3) To save data and exit, press the ‘NEAR’ key.

4) To cancel recording and delete the recorded data, press the
‘FAR’ key.

<EDIT PATTERN>

====================================================

MOVE TO START POSITION
[NEAR:START/FAR:CANCEL]

After define the ‘PATTERN NUMBER’,
select ‘<EDIT PATTERN>’
and press the ‘NEAR’ key

After define starting position,
press the ‘NEAR’ key to start recording

Memory size is displayed.
To save data, press the ‘NEAR’ key.

3

4

<EDIT PATTERN>

====================================================

[MEMORY]
[NEAR:SAVE/FAR:DELETE]

23

FUNCTION SETUP > GROUP SETUP

OSD -

1

2

<FUNCTION SETUP>

====================================================

<PRESET SETUP>
<SCAN SETUP>
<PATTERN SETUP>
<GROUP SETUP>

BACK
EXIT

<GROUP SETUP>

====================================================

GROUP NUMBER

<

EDIT GROUP >
CLEAR GROUP

BACK
EXIT

1

CANCEL

3

Select ‘<GROUP SETUP>’
and press the ‘NEAR’ key

After define the ‘GROUP NUMBER’,
select ‘<EDIT GROUP>’
and press the ‘NEAR’ key

GROUP SETUP SCREEN

The group function allows running sequence of presets, pattern
and/or scans. Max. 8 group can be stored. Each group can have
max. 20 action entities which can be preset, pattern or scan.

Preset speed can be set up and the repeat number of pattern
& scan can be set up in group setup. Dwell time between
actions can be set up also.

EDIT GROUP - Initial Screen

Press the ‘NEAR’ key to start group setup.

EDIT GROUP – Select Function Sequence

Note that max. 20 functions are allowed in a group.
Move cursor up/down and press the ‘NEAR’ key to set up.

EDIT GROUP - Assign Function

Move cursor to the ‘NO.’ to assign the function, click the enter
button to set up. Select the function by

clicking up/down button.

GROUP NUMBER

Selects group number to edit.

<EDIT GROUP>

Starts editing group.

CLEAR GROUP

Deletes data in the current group.

1 ~ 8

CANCEL / OK

NO.

Means the sequence of the function in a group.
The functions will be run from lower no. to higher no. by sequence.

ACTION NUM

Select the function.

DWELL

Sets dwell time between function by moving joystick up/down. If the
‘OPT’ of pattern/group is set to repeat more than twice, it means the
repeat interval.

OPT

It represents preset speed (1~360) when preset is selected. It should
be the number of repetition (1~255) when pattern or scan is selected
for ‘ACTION’.

1 ~ 20

NONE / PRESET 1~255 / PATTERN 1~4
/ SCAN 1~8

00:03 ~ 04:00 (min:sec)

PRESET: 1~360 / PATTERN & SCAN: 1~255

Preset

1

Preset

120

Pattern5

1 Times

Pattern5

n Times

Dwell Time

Max. 20 Entities

Scan3

1

3

4

5

2

3

4

OPT

<EDIT GROUP>

====================================================

NO.

====================================================

1
2
3
4
5

====================================================

EDIT
SAVE
CANCEL

OPTDwellACTION

NONE
NONE
NONE
NONE
NONE

Num

<EDIT GROUP>

====================================================

NO.

====================================================

1
2
3
4
5

====================================================

EDIT
SAVE
CANCEL

OPTDwellACTION

NONE
NONE
NONE
NONE
NONE

Num

Press the ‘NEAR’ key to start editing

Select function sequence number
by move joystick up/down.
And press the ‘NEAR’ key.

24

FUNCTION SETUP > GROUP SETUP

OSD -

5

6

3

Move joystick up/down to select action.
and move joystick right.

After define items,
press the ‘NEAR’ key

EDIT GROUP - Assign Function

Move cursor to the ‘NO.’ to assign the function, press the ‘NEAR’
key to set up. Select the function by moving joystick up/down.

5

7

8

OPTACTION

NONE
NONE
NONE
NONE
NONE

<EDIT GROUP>

====================================================

NO.

====================================================

1
2
3
4
5

====================================================

EDIT
SAVE
CANCEL

Dwell

<EDIT GROUP>

====================================================

NO.

====================================================

1
2
3
4
5

====================================================

EDIT
SAVE
CANCEL

OPT
1

Dwell
00:02

ACTION
PRESET

NONE
NONE
NONE
NONE

Num

1

Press the ‘FAR’ key,
and move joystick down
to select ‘SAVE’

Press the ‘NEAR’ key
to save current data.

EDIT GROUP - Assign Function

Move cursor left/right to select items and move cursor up/down
to change each value.

EDIT GROUP - Select Function Sequence

e.g.) If ‘PRESET 1’ is not defined at ‘ROOT MENU>FUNCTION
SETUP>PRESET SETUP’, then the ‘ACTION’ will be
automatically changed to ‘NONE’.

The function undefined cannot be set as action.

EDIT GROUP - Saves the Setting

After finishing setting up all actions, place cursor on ‘SAVE’.
Then, press the ‘NEAR’ key to save current data.

8

6

7

Num

<EDIT GROUP>

====================================================

NO.

====================================================

1
2
3
4
5

====================================================

EDIT
SAVE
CANCEL

OPT
1

Dwell
00:02

ACTION
PRESET

NONE
NONE
NONE
NONE

Num

1

<EDIT GROUP>

====================================================

NO.

====================================================

1
2
3
4
5

====================================================

EDIT
SAVE
CANCEL

OPT
1

Dwell
00:02

ACTION
PRESET

NONE
NONE
NONE
NONE

Num

1

Press the ‘NEAR’ key

<EDIT GROUP>

====================================================

NO.

====================================================

1
2
3

OPT
1

Dwell
00:02

ACTION
PRESET

NONE
NONE

Num

1

<EDIT GROUP>

====================================================

NO.

====================================================

1
2
3

OPTDwellACTION

NONE
NONE
NONE

Num

25

CAMERA SETUP

OSD -

1

2

<CAMERA SETUP>

====================================================

FOCUS MODE
DIGITAL ZOOM

<

WHITE BALANCE SETUP>
<AUTO EXPOSURE SETUP>
<OTHER SETUP>

BACK
EXIT

AUTO
OFF

<WHITE BALANCE SETUP>

====================================================

WB MODE
R-GAIN
B-GAIN

BACK
EXIT

AUTO
100
100

3

‘<ALARM INPUT SETUP>’ select
and press the ‘NEAR’ Key

WB MODE

- AUTO: Camera perform white balance automatically.

- Manual: ‘R/B-Gain’ level can be set up manually.

- ONE PUSH: WB is executed once on the scene you designated.

- INDOOR: WB will be done under assumption of Indoor illumination.

- OUTDOOR: WB will be done under assumption of Sun light.

RED ADJUST

BLUE ADJUST

AUTO / MANUAL / ONE PUSH> / OUTDOOR /
INDOOR

0 ~ 255

0 ~ 255

CAMERA SETUP

Setup the general functions of zoom camera module.

WHITE BALANCE SETUP

1

2

FOCUS MODE

Sets the camera focus mode.

- AUTO: This mode exchanges the focus mode automatically
between manual focus mode and auto focus mode. Manual focus
mode activates in preset operation and auto focus mode activates
when jog operation starts.

- MANUAL: With manual mode at presets, focus data is memorized in
each preset in advance and camera calls focus data in correspondence
with presets as soon as camera arrives at a preset.

DIGITAL ZOOM

Sets digital zoom function to ‘ON’ or ‘OFF’. If this is set to ‘OFF’, optical
zoom function runs but zoom function stops at the end of optical zoom
magnification.

<WHITE BALANCE SETUP>

Starts ‘WHITE BALANCE SETUP’ setup screen.

<AUTO EXPOSURE SETUP>

Starts ‘AUTO EXPOSURE SETUP’ setup screen.

<OTHER SETUP>

Starts ‘OTHER SETUP’ setup screen.

AUTO / MANUAL

ON / OFF

26

CAMERA SETUP > AUTO EXPOSURE SETUP

OSD -

1

2

<CAMERA SETUP>

====================================================

FOCUS MODE
DIGITAL ZOOM

<

WHITE BALANCE SETUP>
<AUTO EXPOSURE SETUP>
<OTHER SETUP>

BACK
EXIT

AUTO
OFF

<AUTO EXPOSURE SETUP>

====================================================

BACK LIGHT
DAY/NIGHT
AE MODE
* SHUTTER
* IRIS
* GAIN
* BRIGHT
SLOW SHUTTER

BACK
EXIT

OFF
AUTO
AUTO
1/60
F2.0
4dB
20
ON

3

‘<AUTO EXPOSURE SETUP>’ select
and press the ‘NEAR’ Key

BACK LIGHT

Sets the backlight compensation.

DAY/NIGHT

‘AUTO’ exchanges day/night.

AE MODE

- AUTO: Full auto mode for AE function

- MANUAL: In manual mode. ‘IRIS’, ‘GAIN’, ‘SHUTTER SPEED’ can be

changed in this mode.

- IRIS: Iris priority mode. You can change iris while others are adjusted
automatically.

- SHUTTER: Shutter priority mode. Shutter speed can be changed while
while others are adjusted automatically.

- BRIGHT: In this mode, you can assign AE value in terms of brightness.

IRIS LEVEL

Works when ‘AE MODE’ is ‘MANUAL’ or ‘IRIS’ mode.

GAIN LEVEL

Works when ‘AE MODE’ is ‘MANUAL’.
Enhances image brightness automatically in case that luminance
level of image signal is too low.

SHUTTER SPD

Works when ‘AE MODE’ is ‘MANUAL’ or ‘SHUTTER’ mode.

BRIGHTNESS

Works when ‘AE MODE’ is ‘BRIGHT’.
Adjusts brightness of images. Iris, shutter speed and gain are
adjusted automatically in correspondence with this value.

SLOW SHUTTER

Turn On/Off slow shutter function. If you turn this on, the shutter speed
is slowed down to intensify image by accumulating small light in the
extremely dark environment. This function is effective only in Full Auto
AE mode.

ON / OFF

AUTO / DAY / NIGHT

AUTO / MANUAL / IRIS / SHUTTER / BRIGHT

CLOSE / F1.8 / F2.0 / F2.4 / F2.8 / F3.4 / F4.0 /
F4.8 / F5.6 / F6.8 / F8.0 / F9.6 / F11 / F14 / F16
/ F19 / F22 / F26 (18 steps)

-3 / 0 / 3 / 6 / 9 / 12 / 15

1/2 ~ 1/10000 (21 steps)

0~31 (32 steps)

ON / OFF

AE SETUP

2

27

CAMERA SETUP > OTHER SETUP

OSD -

1

2

<CAMERA SETUP>

====================================================

FOCUS MODE
DIGITAL ZOOM

<

WHITE BALANCE SETUP>
<AUTO EXPOSURE SETUP>
<OTHER SETUP>

BACK
EXIT

AUTO
OFF

<OTHER SETUP>

====================================================

EXP COMPENSATION
APERTURE
GAMMA
PICTURE EFFECT
WIDE-D
IR CORRECTION
CAM GAIN
HR MODE
NOISE REDUCTION
HIGH SENSITIVITY
BACK
EXIT

0
6
NORMAL
OFF
OFF
OFF
20dB
ON
3
ON

3

‘<OTHER SETUP>’ select
and press the ‘NEAR’ Key

EXP COMPENSATION

Default is ‘0/0dB’.

APERTURE

GAMMA

PICTURE EFFECT

WIDE-D

IR CORRECTION

CAM GAIN

HR MODE

NOISE REDUCTION

HIGH SENSITIVITY

7 (GAIN:-10.5dB)
~ +7 (GAIN:+10.5dB) (15 Steps)

0 ~ 15

NORMAL / GAMMA1 / S-LOW / S-MID / S-HIGH

OFF / NEGATIVE / B&W

ON / OFF

ON / OFF

6 dB ~ 20 dB

ON / OFF

OFF / 1 ~ 5

ON / OFF

OTHER SETUP

2

28

SYSTEM SETUP

OSD -

1

<SYSTEM SETUP>

====================================================

HD-SDI
CLEAR ALL DATA

BACK
EXIT

1920x1080i60
CANCEL

3

HD-SDI

Select the resolution of HD-SDI.

CLEAR ALL DATA

Deletes all configuration data such as display, camera, motion setup
and so on.

1280x720p50 / 1280x720p60 / 1920x1080i50 /
1920x1080i60 / 1920x1080p25 / 1920x1080p30

CANCEL / OK

SYSTEM SETUP

2

29

Unit: mm

182.5

71

286

187

78.7

404.5

146

259

132 182.5

102

142

71

383

187

78.7

146

259

142

102

3/4” PIP THREAD

3/4” PIP THREAD

3/4” PIP THREAD

Wall Mount Bracket

Ceiling Mount Bracket

Dimension

Specifications -

4