Speco VLEDB1HG, VLEDB1HW User Manual

Specifications

Model

Pick-up Device 1/3" 960H CCD

VLEDB1HG/W

VLEDB1HG/W Series Color

Camera

Effective Pixels (H×V) NTSC:976×494

Sensing Area 4.9mm×3.7mm

Horizontal Resolution 700 TV Lines

Minimum Illumination 0.01 Lux, 0 Lux at IR on

S/N Ratio More than 52dB

Scanning System 2:1 Interlace

Synchronous System Internal

Electronic Shutter

IR Distance 98’

IR Leds 36 pcs Φ5 infrared LED

IR status IR on: under 10Lux, by CDS auto control

Water Resistance IP66

Gama Characteristic 0.45

Auto Gain Control Auto

White Balance Auto

Video Output 1.0Vp-p composite video, 75Ω

Lens 2.8-12mm Mega pixel Lens

1/50s(1/60s)～1/100,000s

IR Bullet Camera

Power/Current 12VDC/ IR on: 400mA, IR off: 80mA

Operating Temperature

Storage Temperature

14F～122F

-4F～140F

Note:Before applying power to the cam-

era, please read this UserGuide in detail.

PRODUCT FEATURES

* Sensor (CCD)

1/3"CCD sensor.

* Auto Gain Control (AGC)

Built-in auto gain control (AGC) circuit. The color camera
can get a high definition picture in low Lux condition.

* Auto Electronic Shutter (AES)

Built-in auto electronic shutter function. The AES speed

can reach 1/100,000s.

* Gamma Characteristic
Camera Gama characteristic is 0.45.

* Night-time Vision

0 Lux with IR LED ON.

CONNECTING

Monitor

DC12V Power Supply

Link wire rule：

Video

Power

INTRODUCTION

Congratulations on your purchase of this Speco
product. This camera utilized the latest sensors

Video

12V DC

and drivers. The most appealing characteristics of
this camera are weather-resistance, day & night
feature, and indoor & outdoor applications. This
product is a great addition to your CCTV system.

Please read this manual carefully to ensure proper
use of the product.

The symbol is intended to alert the user to the presence of

important operating and maintenance (servicing)
Instructions in the literature accompanying the appliance.

The symbol is intended to alert the user to the presence of

uninsulated ‘dangerous voltage’ within the product’s

enclosure that may be of sufficient Magnitude to consti­a risk of electric shock to persons.

Power Supply Notes：

●The power supply must be regulated 12V supply.

●The operating temperature must be within camera’s specifications.

●For better image quality, the cable length for power and video output

should not be excessively long.

TROUBLESHOOTING

1. No picture after providing power

. Check the power supply voltage, it may be outside specification.
. Please check the connecting cables and monitors to determine if the

camera is connected correctly or not.

2. The picture has flowing interference ripples

. Check the ground of the monitor and other peripheral equipment that

are being used is the same ground as the camera.

3. The background color continuously changes

. A fluorescent bulb’s electromagnetic field can cause a color roll. This is

a proper phenomenon of the camera.

. To improve the image, try to increase the distance between the camera

and the bulb, or change the angle such that it doesn’t face the flores-

cent bulb.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER. NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING

CAUTION:
To prevent electric shock and risk of fire hazards,
do NOT use anything other than the specified power

Installation Precautions:

● Do not install the camera to extreme temperature condi-

tions. Only use the camera under conditions where tem­perature is between 14f and 122f.

● Never keep the camera pointed directly at the sun or a

bright object.

● Do not mount the camera near a radiator or heater.

CAUTION: