Speco P32S36GM User Manual

User Manual
Rackmount Managed Ethernet PoE Switch
SCAN THIS QR CODE TO DOWNLOAD THE FULL WEB CONFIGURATION GUIDE, or go to http://www.SpecoTech.com and search for P32S36GM.
1. Console port
2. Power light
3. Reset button
4. System running light
5. PoE interface
6. SFP optical interface
7. Grounding stud
8. AC power input (100-240V 50/60Hz)
Note
Please connect the power supply correctly, otherwise you could damage the equipment.
Product Description for Ethernet PoE Switch Introduction
The 1U rack-mounted Ethernet switch provides excellent quality such as high/low temperature resistance and lightning protection through fanning cooling circuit design, wide-range working environment temperature, and high protection level; It integrates various protocols such as routing, switching, security, and supports ERPS, which greatly improves networking flexibility and enhances the reliability and security of networks. It can better meet the deployment requirements of rail transit, safe city, intelligent transportation, outdoor surveillance and other projects in harsh environments.
Description
Basic description of appearance 1: Table 1-1
Table 1-1
FIG.1
FIG.2
Indicator Light
Panel Sign
status
meaning
Power input indicator
PWR
Light off
The power supply has no input
Steady green
Power input is normal
System indicator light
SYS
Light off
The device is not powered on
Flashing green
Device is initializing
Steady green
The equipment is working
Ethernet electrical port indicator
/
Green light off
Port is not connected
Steady green
Port is connected
Flashing green
Port data sending and receiving
Yellow light
PoE is not power supply
Yellow light off
PoE in power supply
Ethernet optical port indicator
/
Light off
Port is not connected
Steady green
Port is connected
Flashing green
Port data sending and receiving
Reset
/
How to restore factory settings: long press (more than 10s)
Indicator and Button Description
Serial Port Description
Interface parameters: baud rate is 115200, data bit is 8, parity bit: none stop bit 1, no ticking flow control.
FIG.3
Installation of Device
1. Install the rack nut.
2. Lift the device and rotate the screws through the mounting ear holes of the switch to fasten with the
nuts.
As shown below: As shown below when completed:
Power Set-up Diagram
Connect the AC power supply according to the signs on panel, the AC power supply is connected to voltage is 100-240V. As shown below:
FIG.4
Network Cable Installation
Ethernet port: use cat5e or cat6 network cable;
Network cable sequence: Both 568A and 568B; crossover cable and straight-through
cable are acceptable.
568A standard: white green, green, white orange, blue, white blue, orange, white
brown, brown. (3, 6, 1, 4, 5, 2, 7, 8)
568B standard: white orange, orange, white green, blue, white blue, green, white
brown, brown. (1, 2, 3, 4, 5, 6, 7, 8) Crossover cable: one end is 568A, the other end
is 568B.
Straight line: both ends are 568A or 568B, normally both ends are 568B
FIG.5
PoE Set-up
PoE is a technology that uses Power over Ethernet. The device supports 802.3af and
802.3at standards. It requires the switch to connect to the power supply between DC48V-58V. The POE connection is consistent with the network cable connection. The 1,2,3,6 cable is used for both data transmission and POE power supply.
List of Accessories
Switch Power Line Console Cable Certificate of Conformity Warranty Card & Manual
Warranty Policy
We warranty this product to be free from any manufacturing or material defects for 2 years from the date of purchase. This warranty will not extend to any products which have been subjected to misuse, neglect, accident, or improper installation, used in violation of instructions furnished by us; or to units which have been repaired or altered outside of the factory. This limited warranty does not apply to broken cases, batteries, or other physically damaged parts.
Upon request by the customer, Speco Technologies will at the customer’s expense repackage merchandise in new cartons, replace missing accessories, and return in resalable condition. Unless requested, Speco Technologies will replace and return all merchandise in the packaging in which it was received. This warranty is in lieu of all expressed warranties, expressed or implied, and of all obligations or liability on our part, and we neither assume nor authorize any representative or other person to assume for us any obligation or liability. In no event shall we be liable for incidental or consequential damages arising from the use of the product, or for any delay in the use of this product do to causes beyond our control. Some states do not allow limitations of how long an implied warranty lasts and/or do not allow the exclusion or limitation of consequential damages. The above limitations on implied warranty and consequential damages may not apply to you. This warranty gives you specific legal rights. You may have other rights which vary from state to state.
Speco Technologies is constantly developing and improving products.
We reserve the right to modify product design and specifications without notice and without incurring any obligation.
Speco Technologies . 200 New Highway . Amityville . NY . 11701 .
www.specotech.com Rev. 12/21/20
Loading...