Speco O2iD8 Installation Guide
Intensifier® IP Dome Camera
QUICK INSTALLATION GUIDE
O2iD8
Please read this guide carefully before installation and operation of the product.
Notice
This installation should be made by a qualified service person and should conform to all local codes.
The lighting flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of non-insulated dangerous voltage within
the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION
Thank you for purchasing this product. This guide is designed to be a reference tool for the product. Please read
it carefully before operating the product and retain it for future reference. Should you require any technical
assistance, please contact Speco Technologies Technical Support.
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at its own expense.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to
operate the equipment.
CAUTION – To prevent electric shock and risk of the fire hazards
Do NOT use power source other than that specified.
Do NOT expose this appliance to rain or moisture.
1
PRECAUTIONS
Please read the manual carefully before the installation in order to set up the camera correctly and to obtain
the best picture quality.
Installation and services should only be carried out by an authorized personnel according to local safety
regulations.
If any liquid or solid matter gets into the housing, immediately disconnect the camera from power supply and
have it checked by your authorized dealer before reusing.
Avoid installing the camera in extremely hot or cold places.
If you are not a certified person, never try to dismantle the camera.
To avoid electric shock, never remove the screws or covers. There are no parts inside that need maintenance
by the user. All maintenance should be carried out by qualified personnel.
Avoid installing the camera in a place of high humidity.
Avoid installing the camera at a place exposed to gas or oil.
Don't point the camera directly at sunlight.
Please pay special attention to keep the unit from dropping or external shock during the process of
transportation or handling.
Never try to touch the camera with wet hands. It may cause an electric shock.
Do not expose the camera to radioactivity. It can cause a serious damage on the image sensor.
LIMITATION OF LIABILITY
This publication is provided “AS IS” without warranty of any kind, either express or implied, including but not
limited to, the implied warranties of merchantability, fitness for any particular purpose, or non-infringement of
the third party's right.
This publication could include technical inaccuracies or typographical errors. Changes are added to the
information herein, at any time, for the improvements of this publication and / or the corresponding product(s).
DISCLAIMER OF WARRANTY
In no event shall seller be liable to any party or any person, except for replacement or reasonable maintenance
of the product, for the cases, including but not limited to below :
(1) Any damage and loss, including without limitation, direct or indirect, special, consequential or
exemplary, arising out of or relating to the product.
(2) Personal injury or any damage caused by inappropriate use or negligent operation of the user.
(3) Unauthorized disassembly, repair or modification of the product by the user.
(4) Inconvenience or any loss when images are not displayed, due to any reason or cause
including any failure or problem of the product.
(5) Any problem, consequential inconvenience, or loss or damage, when combined with third party devices.
(6) Any claim or action for damages, brought by any person or organization, due to a violation of privacy when
the surveillance footage, for some reason, becomes public or is used for the purpose other than
surveillance.
2
1. PRODUCT OVERVIEW
CLASSIFICATION
Night Vision Outdoor IR Camera
General
CPU
ARM1176JZF-STM ( 400 MHz, Instruction cache : 32kbyte,
data cache : 16kbyte, MMU )
Flash
2Gbit Flash Memory
SDRAM
2Gbit DDR3 Memory
Image Pickup
Image Sensor
2.0 Megapixel 1/2.8" SONY progressive scan CMOS image sensor
Total Pixels
1952(H) x 1116(V) 2.18 Megapixel
Effective Pixels
1944(H) x 1104(V) 2.14 Megapixel
S/N Ratio
More than 50dB
Min. Illumination
0.1Lux
Lens
3.6mm Megapixel Lens (F=0.94)
Video
Video Compression
H.264 High Profile @ Level 4.1, Motion JPEG
Resolutions
Up to 1920 x 1080
Frame rate
H.264 Up to 30fps with 1920 x 1080
H.264 Up to 30fps with VGA resolution
MJPEG Up to 30fps with VGA resolution
Video Streaming
Support Multi Stream with H.264, MJPEG
Adjustable Frame Rate
VBR / CBR in H.264
Image Setting
Brightness, Contrast, Sharpness
Auto White Balance Auto Exposure
Privacy Mask
DSS, Corridor-view (in H.264), Mirror / V-Flip, etc.
D-WDR (Low / Middle / High)
Network
Security
Password Protection
User Access Log
HTTPS Encryption
Supported Protocol
HTTP, HTTPS, DNS, RTSP, RTP, TCP, UDP, ICMP, DHCP
System
Intelligent Video
Motion detection 12 x 12 blocks
Key Features
2.0 megapixel progressive scan CMOS image sensor for excellent image quality
Low light, Ultra high sensitivity camera
IP66 compliant
Vandal-resistant
3-axis mechanism
Built-in temperature / humidity sensor
Heater operation according to humidity
Triple Stream for simultaneous operations
Up to 30 frames per second at all image resolutions
Integrated motion detection with pre- and post-alarm image / video buffering
Supports CBR (constant bit rate) and VBR (variable bit rate) modes
Tampering-Alarm function
Controllable frame rate
Privacy Masking up to 8 areas
Built-in PoE (power over Ethernet)
HTTPS support
DDNS and DHCP client
Specification
3
Loading...