Speco O2iB92, O2iD21M User Manual
User Manual
Intensifier® IP Camera
(O2iB92/O2iD22/O2iD21M/O2iB91M)
Please read this manual carefully before operating the unit and keep it for further reference
4
Welcome
Thank you for purchasing this network camera!
Please read this manual carefully before operating the unit and retain it for future reference.
Should you require any technical assistance, please contact Speco Technologies Technical Support.
Important Safeguards and Warnings
1．Electrical Safety
All installation and operation here should conform to local electrical safety codes.
Use a certified/listed 12VDC Class 2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same time; it may result in
device damage! The product must be grounded to reduce the risk of electric shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
Speco Technologies assumes no liability or responsibility for any fires or electrical shock caused by improper
handling or installation.
2．Transportation
Heavy stress, violent vibration or exposure to water is not allowed during transportation, storage and installation.
3．Installation
Handle the device with care. Keep the device right side up.
Do not apply power to the camera before completing installation.
Do not place objects on top of the camera.
4．Repair Professionals
All examination and repair work should be done by qualified personnel only.
Speco Technologies is not liable for any problems caused by unauthorized modifications or user-attempted
repair.
5
5．Environment
The camera should be kept in a cool, dry place away from direct sunlight, flammable materials, explosive
substances, etc.
This product should be transported, stored, and used only in the specified environments as stated above.
Do not aim the camera at a strong light source, as it may cause overexposure of the picture, and may affect the
longevity of the camera’s sensors.
Ensure that the camera is in a well ventilated area to prevent overheating.
6. Operation and Maintenance
Do not touch the camera sensor or lens directly.
To clean dust or dirt off of the lens, use an air blower or a microfiber cloth.
6
Ta b l e o f C o n t e n t s
1.1 Applications ............................................................................................................................................. 9
1.2 LAN Access to Web Setup Interface .................................................................................................. 10
2 Live View .............................................................................................................................................................. 13
2.1 Menu Bar ................................................................................................................................................. 13
2.2 Sta tus Bar ............................................................................................................................................... 14
3 Recording .............................................................................................................................................................. 15
4 Setup ..................................................................................................................................................................... 16
4.1 PC Path Se tup ......................................................................................................................................... 16
4.2 Basic Setup ............................................................................................................................................. 16
4.2.2 Privacy Mask ............................................................................................................................... 18
4.2.3 Image Setu p ................................................................................................................................ 18
4.2.4 Region of Interest ...................................................................................................................... 20
4.2.5 OSD Setup ................................................................................................................................... 21
4.3 Network Setu p ....................................................................................................................................... 22
4.3.1 IP/Por t Setup .............................................................................................................................. 22
4.3.2 PPPOE Setup ............................................................................................................................... 23
4.3.3 DDNS Client ................................................................................................................................. 24
4.3.4 Ema il Setup ................................................................................................................................. 25
4.3.5 FTP Setup ..................................................................................................................................... 26
4.3.6 SNM P ............................................................................................................................................ 27
4.3.7 UPN P ............................................................................................................................................. 27
4.3.8 HTTPS ........................................................................................................................................... 28
4.3.9 RTSP .............................................................................................................................................. 28
4.3.10 IP Filterin g................................................................................................................................. 29
7
4.3.11 Zero Configuration .................................................................................................................. 29
4.4 Event Setup ............................................................................................................................................ 31
4.5 Record ...................................................................................................................................................... 33
4.5.1 Record Schedule ........................................................................................................................ 33
4.5.2 SD card Ma nagement ................................................................................................................ 33
4.5.3 Snapshot Schedule .................................................................................................................... 34
4.5.4 Destination ................................................................................................................................. 35
4.5.5 NAS ............................................................................................................................................... 35
4.6 System ..................................................................................................................................................... 37
4.6.2 System .......................................................................................................................................... 38
4.6.3 Set Time ....................................................................................................................................... 38
4.6.4 Use r Admin ................................................................................................................................. 39
8
1
Connection Guide
1.1 Applications
Below are the main applications for use with the IP camera:
9
1.2 LAN Access to Web Setup Interface
The IP camera settings can be accessed via a web browser through the LAN using the IP Scanner tool.
Network connection:
1. Make sure that the camera and the PC are connected on the same local network. The camera is set to
DHCP by default and will be assigned an IP address by the DHCP server. Make sure that the local network
has a DHCP server. Routers typically have a DHCP server built in.
2. Install IP Scanner from the CD and run it after installation. IP Scanner is the tool for discovering the IP
cameras on the local network.
3.
In the device list, the IP address, model number, and MAC address of each device will be listed. Select
the applicable device and double click to open up the web viewer. You can also manually enter the IP
address in the address bar of the web browser.
10
Note
The IP camera will have DHCP turned on by default. If there is no DHCP server available, the
IP camera’s IP address will default to 192.168.0.66.
The login interface is shown below. Default Username and Password: admin/1234. After logging in,
follow directions to install applicable plug-ins for viewing video on the browser.
11
After logging in the web interface will be displayed as shown below:
Available functions on the Web Interface:
• Live view
• Save a recording onto the local computer.
• Playback local recordings.
• Modify IP camera parameters, change settings, change video quality and system time.
12
Menu Bar
2
Live View
The live view page has two function bars:
Parameter
1.
2.
Description
Status Bar
2.1 Menu Bar
Click here to log out
Live: Live view
Recording: Playback of local recordings
Setup: System Setup
13
④ ⑤ ③ ⑩
Blue: Sensor alarm has been set up and
activated
Blue: Motion alarm has been set up and activated
Single click on this icon will bring the video to full
screen.
⑧ Schedule
Single click will capture a screenshot. The save directory can
① ② ⑥
⑦
⑧ ⑨
2.2 Status Bar
Parameter icon Description
① Main Stream
② Sub Stream
③Sensor alarm
④Motion Alarm
⑤ Privacy Mask
Alarm
⑥ Full screen
⑦ Manual Record
Recording
Switches to main stream view
Switches to sub stream view
Displays the Sen sor ala rm stat us:
White: Sensor alarm has not been set up
Displays the Motion alarm status:
White: Motion alarm has not been set up
Display the Privacy mask alarm status:
White: Privacy mask alarm has not been set up
Blue: Privacy mask alarm has been set up and activated
Double click on the video or hit “ESC” to exit full screen.
Single click will start the manual record mode on the PC
Shows t he status of Schedule recordin g:
White: Schedule recording has not been set up.
Blue: Schedule recording has been set up and is currently
recording
⑨ Audio
⑩ Screen Capture
Toggle audio on/off
be configured in settings.
14
Loading...