Speco O2D60M Quick Install Manual

QUICK INSTALL GUIDE

O2D60M
Full HD Vandal Dome IP Camera

Please read this guide carefully before operating
the unit and retain it for future reference.

This lightning flash with arrowhead symbol within an equilateral triangle
is intended to alert the user to the presence of uninsulated dangerous
voltage within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the product.

WARNING: This product contains chemicals known to the State of California to cause cancer
and birth defects or other reproductive harm. Wash hands after handling.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user could lose the authority to operate
this equipment if an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to
radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.

• A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of

this product in the end user.

• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries

according to the manufacturer’s instructions.

• Holes in metal, through which insulated wires pass, shall have smooth well rounded

surfaces or shall be provided with brushings

.

• Extremely hot or cold places (operating
temperature -10 °C to 50 °C, however, we

recommend that the unit be used within

a temperature range of 0 °C to 45 °C)

• Damp or dust place

• Places exposed to rain

• Places subject to strong vibration

• Close to generators of powerful

electromagnetic radiation such as radio
or TV transmitters.

• Do not use the camera in such place

where rapid temperature fluctuation by

switching an air conditioner on and off.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Warning: Do not install this equipment in

a confined space such as a bookcase or
similar unit.

Note:

Please make sure the product is installed
appropriate places where secured from
flood, such as under the eaves, to operate
properly. This product is certified as IP66

standard. However, if there is any flood

concerns, it is highly recommended to use

an outdoor Housing. When you install the
camera inside an outdoor Housing, please
use one of the following methods:

1. Remove the front glass of Housing

before installing the camera.

2.

To keep the front glass of Housing,

remove the front cover, and then put
the camera close to the front glass.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.

Install in accordance with the
manufacturer’s instructions.

8. Do not install near any heat sources

such as radiators, heat registers, stoves,
or other apparatus (including amplifiers)
that produce heat.

9. Do not defeat the safety purpose of
the polarized or grounding-type plug.

A polarized plug has two blades with

one wider than the other. A grounding
type plug has two blades and a third
grounding prong. The wide blade or the
third prong are provided for your safety.
If the provided plug does not fit into

your outlet, consult an electrician for
replacement of the obsolete outlet.

10. Protect the power cord from being

walked on or pinched particularly

at plugs, convenience receptacles, and
the point where they exit from the apparatus.

Be careful not to spill water or other liquids in the
unit. Be cautious not to get combustible or

metallic material inside the body. If used with
foreign matter inside, the camera is liable to fail or to

get cause of fire or electric shock.

Avoid viewing a very bright object (such as

light fittings) during an extended period. Avoid
operating or storing the unit in the following
locations.

• Remove dust or dirt on the surface of the

lens with a blower.

• Use a soft and lint-free, dry cloth(such as

glass cleaner) to clean the body. If it is
very dirty, use a cloth dampened with a

small quantity of neutral detergent then
wipe dry.

• Avoid the use of volatile solvents such

as thinners, alcohol, benzene and
insecticides.
They may damage the surface finish and/
or impair the operation of the camera.

•

This camera is designed for mounting

on the ceiling or wall. If you install this

camera upside down, it may cause
malfunction.

11. Only use attachments/accessories
specified by the manufacturer

.

12. Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or

sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus

combination to avoid injury from tip-over

.

Handling of the unit

Operating and storage
location

13. Unplug this apparatus during lightning

storms or when unused for long periods

of time

.

14. Refer all servicing to qualified service

personnel. Servicing is required when
the apparatus has been damaged in any

way, such as power-supply cord or plug

is damaged, liquid has been spilled

or objects have fallen into the apparatus,

the apparatus has been exposed to rain
or moisture, does not operate normally,
or has been dropped.

Important Safety
Instructions

Caution: Make sure the power supply voltage

is correct before using the camera.

Caution: Do not drop the camera or subject it

to physical shock.

Caution: While shipping, the camera should
be packed in its original packing.

Warning: Wiring methods shall be in

accordance with the National Electric Code,
ANSI/NFPA 70.

Warning: To reduce a risk of fire or electric
shock, do not expose the internal apparatus
to rain or moisture

Warning: Install the camera on a ceiling or
wall where can withstand the weight of 5
times of the camera including mounting
bracket.

Caution: The internal apparatus shall not be
exposed to water (dripping or splashing) and

no objects filled with liquids, such as vases,

shall be placed within the enclosure

Caution: The sensor may be burned out by a
laser beam, so when any laser equipment is
being used, make sure that the surface of the
sensor not be exposed to the laser beam.

Caution: This installation shall be made by a
qualified service person and shall conform to
all local codes.
Caution: To avoid electrical shock, do not
open the cabinet. Refer servicing to qualified
personnel only.

Warning: Please adopt the power adapter
which can meet the safety extra low voltage

(SELV) standard. And source with DC 12 V or
AC 24 V (depending on models) according
to the IEC60950-1 and Limited Power Source

standard.

Warning: This is a class A product. In a
domestic environment this product may
cause radio interference in which case the
user may be required to take adequate measures.

To disconnect power from mains, pull
out the mains cord plug. When installing
the product, ensure that the plug is easily
accessible.

MODEL

AUDIO

GENERAL

CAMERA

VIDEO

INPUTS/OUTPUTS

CONNECTORS

Lens Type

Lens Iris Control

LENS

Alarm Out

Ethernet Port

Dimensions (Ø x H)

Unit Weight

Compression Algorithm

3~10mm Motorized Focus Lens

DC Auto Iris

1/2.8” 2 Mega Pixel Sony CMOS

IR LED Off : 0.5Lux, IR LED On : 0Lux

Progressive Scan

74.7dB or Higher (90dB or higher)

Auto

42pcs (850nm)

Wires

RJ-45

5.5”(W)X4.3”(H)X5.5”(D)

3.08lbs

G.726 (16KHz), G.711 μ – Law (8KHz)

Image Sensor

Minimum Illumination

Scanning Mode

Dynamic Range (D-WDR)

Electronic Shutter

IR LED

Compression Algorithm

Compression Resolution

Bitrate Control

Maximum Frame Rate

Multi Stream

H.264, M-JPEG

352X240, 704X480, 1280X720, 1920X1080

H.264-CBR /VBR (up to 12Mbps)

30ips @ 1920X1080 + 30ips @ 4CIF

Primary, Secondary, Tertiary

1 Composite, 1 Vp-p

1 line in

1 line out

1 TTL, NC/NO programmable, 4.3V (NC) or 0.3V (NO) threshold, 5 VDC

1 relay out, NO only, 0.3A @ 125 VAC, 1A @ 30 VDC

10/100 Mbps Ethernet

BNC

Φ 3.5 audio jack

Wires

Video Output

Audio Input

Audio Output

Alarm Input

Alarm Output

Network Connectivity

Video Output

Audio In/Out

Alarm In

Specification

CAUTION

RISK OF ELECTRIC SHOCK
DO NOT OPEN

CAUTION

RISK OF ELECTRIC SHOCK
DO NOT OPEN

CAUTION

RISK OF ELECTRIC SHOCK
DO NOT OPEN

02D60M

This manual is intended for users of the network camera and includes instructions for using and managing the camera on the network

Introduction

Fetures

• Multistream for live monitoring and recording

• H.264 and M-JPEG compression algorithm

• Four levels of video compression and various video compression resolutions

• Two-way audio communication

• Pre- and post-event buffering and video stream buffering to enhance reliability of network recording

• Remote monitoring via web browser or remote software

• Automatic HTML code generation for webcasting on a user’s website

• Up to 10 simultaneous connections to the camera for remote monitoring

• Enhanced security using IP address filtering, HTTPS, SSL and IEEE 802.1X functions and password protected

• multiple user levels

• Network bandwidth limit and MAT functions to use network bandwidth efficiently

• Convenient network connection using the UPnP (Universal Plug and Play) function and built-in mDNS (Multicast

DNS) protocol

• Supports ONVIF protocol

• Digital WDR (Wide Dynamic Range) to adjust the image display in high contrast conditions

• Slow shutter to reduce the minimum illumination requirements

• Day and night functionality with the built-in IR-cut filter changer

• Auto focus functionality

• Convenient firmware upgrades via the network connection

• Firmware duplication and autorecovery functions to enhance system stability

• Management of multiple cameras via Ethernet connections

• Event detection functions: motion, trip-zone, tampering

• Power sources: 12 VDC, PoE (Power over Ethernet)

• NTSC or PAL programmable video output

Precautions

• Be sure to disconnect the unit before

installation and connection.

• The installation should be made by

qualified service personnel or system

installers.

•

Do not expose the power and

connection cables to moisture, which
may cause damage to the unit.

Connecting to the
Network

Connecting Power Source

Connecting Microphone
and Speaker Device

Connecting Alarm Device

To use a power adapter

To use PoE (Power over Ethernet)

NOTE:

NOTE:

NOTE:

ALARM IN & OUT / ALARM IN & OUT
RETURN (Sensor Input / Relay Output)

NOTE:

You can control and monitor the system via
network. With remote control (monitoring),
you can change the system configuration or
monitor the image

.

Connect the IP camera to your network using

a standard RJ-45 network cable

• When the connecting Alarm and Audio,

tighten the screws

• Put your finger between the power

connector and the camera body to pull
out the connector.

Connect power, using one of the methods

listed below:

Connect a DC 12 V power source to the power

input terminal as shown below.

(recommended power adapter is DC 12 V/1.5

A or above)

Connect an ethernet cable to the LAN port on
the unit and to the PoE device. You must use
a “IEEE802.3af” standard PoE device.

Optionally connect an active speaker and/or

external microphone with a built-in amplifier.

If the camera doesn’t work properly after

connecting to the PoE device, please check if
the PoE device is supplying enough power.

•

The Photo MOS Relay is rated for 100 mA
at DC 20 V or 100 mA at AC 28V.

•
Grasp both ends of the 3 or 4 pin

connector plug and then sway both side
to pull it out.

Keep the microphone away from the speaker

to avoid howling.

Connect the sensor device and alarm (relay)
device to the alarm terminal. Alarm signal is
sent out at an event occurrence.

Alarm terminals are used to connect the
alarm (relay) devices such as sensors, door
switches, etc.

Connection

① IR LED: The sensor in the middle of IR LEDs detects
low illumination and the IR LEDs are lit at night

or under low lighting conditions.

② Lens: Motorized Lens is installed.
③ Bottom Base: Fixed Base on the Wall Ceiling
④ Factory Reset Switch: Use to return all settings to the

original factory settings.

⑤ Power: When camera connect power supply,
LED light on

1. Screw the bottom cover to the wall or ceiling by using the mounting screws provided with the camera. Use the mounting template

provided with the camera.

2. Connect the external devices, network and power adapter.

3. Adjust the angle of the lens for the proper view angle. Refer to the View Angle section below for details.

4. Adjust the focus and zoom by using the focus and zoom lever.

5. Fix the shield case in the tilt adjustment screw.

6. If the camera is a vandal dome model, screw the dome cover to the bottom cover by using the setscrew provided with the camera. If the
camera is a plastic dome model, match the mark beside the cable access hole of the bottom cover and the side cable access hole of the dome cover,
and then turn the dome cover clockwise to lock the dome cover to the bottom cover.

7. Apply power.

WARNING: You might need to reinforce the wall or ceiling. If the wall or ceiling is not strong enough to
support the camera, the camera might fall damaging the camera or causing injuries

Part Names and Functions Connection Guide

Connection Guide

5(6(7

32:(5

①

②

③

④

⑤