Speco HT-INTB4 User Manual

Download

Page 1

◈FEATURE

1. Long visible range at night.(50m Max. indoors, 40m Max. outdoors)

2. This camera uses split glass technology to preven IR light reflection.

3. This camera has a vari-focal IR lens to prevent focus drift under IR lighting.

4. The IR cut filter is removed at night to receive maximum available light.

5. This product is weather resistant to resist rain, snow and other environmental factors. (IP65)

6. This product is made of corrosion-free materials to resist rust and corrosion for extended periods o time.

7. The built-in sunshield helps the camera produce clear pictures under a variety of lighting conditions.

8. Power & video cables are concealed for extra security. (Cable through the mount).

9. Unique bracket allows the camera to be full adjustable from both wall and ceiling mounting positions.

10. Dual voltage operation. You can connect 24V AC

or 12V DC regardless of polarity. The Line-Loc function is available when you use 24V AC power.

11. The IR output level is adjustable to suit any lighting

condition.

12. DNR (Digital Noise Reduction)

By using this DSP chip and associated technology, the amount of low light noise has been significantl reduced, and the signal-to-noise ratio (S/N) and horizontal resolution has been improved resulting in a clear and sharp image display even in low light conditions.

13. Horizontal Resolution of 600 TV Lines

Clear image quality has been achieved by employing a 1/3" SONY Super HAD CCD Ⅱ with 410,000 pixels, which provides a horizontal resolution of 600 TV lines.

14. True day/night ICR exchange of 2 Filters

This camera has a function that automaticall selects the mode that is appropriate for daytime o night-time conditions. The COLOR mode operates in daytime conditions to provide optimum colors, and the BW mode operates in night-time conditions to enhance the definition of the image.

15. PRIVACY function(12 programmable zones per screen))

The privacy zone function makes it possible to mask specific areas of the scene from view.

16. Digital Zoom

This camera has a Digital Zoom (limit 16X)

◐DIMENSION

◈CONFIGURATION

HTINTB4

◈WALL MOUNT INSTALLATION #1

1. Make a hole Ø30mm in diameter for routing cable.

2. Using the mounting plate, drill four holes on the wall.

3. Insert the anchors.

4. Attach the screws.

◈WALL MOUNT INSTALLATION #2

1. Adjust horizontal angle.

1) Loosen the bolt to adjust the horizontal angle o the camera.

2) Use the WRENCH to tighten the bolt after adjusting the camera.

2. Adjust vertical angle

1) Loosen a bolt to adjust vertical angle of the camera.

2) Use the WRENCH to tighten a bolt after adjusting the camera.

Speco Technologies is constantly developing product

improvements. We reserve the right to modify product design

and specifications with out notice and without incurri ng any

obligation.

Rev. 7/7/10.

◈CEILING MOUNT INSTALLATION #1

1. Make a hole Ø30mm in diameter for routing cable.

2. Using the mounting plate, drill four holes on the ceiling.

3. Insert the anchors.

4. Attach the screws.

◈CEILING MOUNT INSTALLATION #2

1. Adjust horizontal angle.

1) Loosen the bolt to adjust the horizontal angle of the camera.

2) Use the WRENCH to tighten the bolt after adjusting the camera.

2. Adjust vertical angle

1) Loosen the bolt to adjust the vertical angle of the

camera.

2) Use the WRENCH to tighten a bolt after adjusting

the camera.

Page 2

◈SPECIFICATION

Model No. HTINTB4

Image Sensor

Effective Pixel 768(H) X 494(V) PIXEL

Cell Size

Scanning System 2 : 1 Interlace

Sync. Type Internal / Line lock(24V AC)

OSD Multi-language

WDR Set SSDR / BLC / HLC / OFF

Resolution Color : 600 TV-Line, B/W : 700 TV-Line

S/N Ratio 52dB(AGC OFF, Weight ON)

Min. Illumination

Color Temp.

Shutter 1/60 ~ 1/120,000sec

Intens ifier AUTO / FIXED / OFF(x2 ~ x512 selectable)

Gain Control LOW / HIGH / OFF

Speco DNR OFF / ON(1 ~ 32 Level adjustable)

V Motion ON / OFF(8 Zone, Alarm output)

Privacy ON / OFF(12 Zone)

Mirror H / V / BOTH / OFF

Clarity ON / OFF(Level adjustable)

D&N ICR(COLOR / Black&White / AUTO)

Stabilize ON / OFF

Digital Zoom ON(x16) / OFF

DPC 256 point(Even 128 point, ODD 128 point)

Power Supply Regulated 12V DC or 24V AC

Current Consumption 150mA(LED OFF), 700mA(LED ON)

Operation Temp.

Dimension

Weight

※The specification is subject to change without any

prior notice to improve the quality.

1/3" SONY SUPER HAD CCD

6.35

㎛

(H) X 7.4㎛(V)

LED ON : 0 Lux(40M Range) LED OFF : 0.0005 Lux(Color Sense-up),

0.0002 Lux(B/W Sense-up) ATW(1,700°K ~ 11,000°K) / AWC / MANUAL / OUTDOOR / INDOOR

-20

℉

to 122℉

3.1”W X 3”H X 6.8”L

3.3Ibs.

Ⅱ

◈FUNCTIONS

1. Setup for camera functions

①SETUP :

Press "SETUP" button to go to the menu.

②Up, ③Down :

Use "UP" or "DOWN" button to navigate.

④Left, ⑤Right :

Use "RIGHT" or "LEFT" button to navigate

⑥EXT-VIDEO :

Test monitor connection.

⑦LED :

LED level adjust. (Factory default is Max.) <Notice > "

"sign means that you can go to a sub menu when

pressing the "SETUP" button. " --- " means that a function is not available.

HTINTB4

2. Camera function setting

Function

Select

setting

DC IRIS ADJUST LENS

MANUAL

BRIGHT-

NESS

E -

SHUTTER

AUTO

GAIN

EXPOSURE

SENS-

RETURN

*Notes : If the AGC is off, the sense-up function is not

available. As the sense-up level increases, an after-

image will appear. ATW Color temperature 1,700~11,000°K OUT-

DOOR IND OO R Color temperature 4,500~8, 500°K

COLOR

MANUA

TEMP

AWC SET

OFF Deactivates function

WDR SET

OFF Deactivates function

SLC

SLC SET

HLC

ON Level

SPECO DNR

OFF Deactivates function

*Notes : If the AGC is off, the DNR function is not available

AUTO

DAY &

EXT

NIGHT

COLOR Fixed at color(LED OFF)

B/W

*Notes : If the AGC is off, this function is unavailable

Page 2 Please refer to "Page 2"

SAVE Save the value and exit menu NOT

EXIT

SAVE DEFAU LTS

Page 1

Sub

Adjust the brightness of the screen

BRIGHT

(Range : 1~70, Defaul t : 25)

NESS,

Adjust the Iris speed of the DC lens

IRIS

(Range : 1~50, Default : 3)

SPEED,

Focus addition : To adjust the lens

FOCUS

focus correctly

ADD.

Manual mode is not recommended

BRIGHT

using built-in the DC Lens(Default :

NESS

25) Brightness ADJ. : Adjust the brightness of the screen when using the DC lens(Range : 1~70, Default : 25)

MANUAL

Auto setting is not selectable when selected DC Lens

FLK, - - -

OFF : Deactivat es function LOW : Auto selection between

5.3dB and 32dB

OFF,

HIGH : Auto selection between

LOW,

5.3dB and 37dB(You cannot

HIGH

use the DIS, Day&Night when AGC is off) OFF : Deactivat es function

OFF,

AUTO : Using sense up when it is

AUTO

low luminance(x2~x512 selectable) Save the value then move back to previous menu

Color temperature 1,700~11,000°K

Adjust the Red or Blue values to shift the color of the screen

→

Find the optimal white balanc e for current luminance environment (The camera focus must towards to white paper)

Wide dynamic range function(1 ~15 level selectable, Default : 8)

LEVEL, TOP,

User programmable SLC zone

BOTTOM,

and compensation level

LEFT, RIGHT LEVEL, LIMIT, MASK COLOR,

Removed HIGH LIGHT, It enable

MASK

us to watch license plate clearly

TONE, TOP, BOTTO M, LEFT, RIGHT

Reduce noise in low illumination (Reduction level is selectable, Default : 20)

BURST MODE COLOR

Day : Color

→

B/W,

(Switching time & speed adjust-

B/W

→

able) COLOR, RETURN

Change the color

ternal signal (Not availabl e)

BURST MODE

Fixed at B/W(LED ON) (OFF/ON),

RETURN

Exit the main menu without save

Reset the camera setup value

to the factory default

Summary

↔

Night : B/W

↔

B/W by ex-

Speci al

Select

setting

V-REV Set a vertical image inversion

H-REV Set a horizontal image inversion DIGI-

ZOOM FONT COLOR

ADJUST

CLARITY

RETURN

LCD

MONITOR

USER

CRT

OFF No title displays on the screen CAM TITLE

INT Internal Sync with 12V DC power SYNC

TYPE

SENSITI

VITY

AREA

MODE

SEL

POS

XPOS MOTION

YPOS

FILL →

SET

RETURN

*Notes : If the camera detected motion, "MOTION

DETECTED" will appear on the screen

AREA

SEL

AREA

MODE

MASK

COLOR

PRIVACY

MASK

TONE

TOP

BOTTOM

LEFT

RIGHT

RETURN

LAN-

Select language

GUAGE

STABI

ON,

-LIZE

OFF

PAG E 1

ㆍThe " " icon appeared with desired function, press the set

button to move sub menu.

ㆍThe "---" icon appeared with function that is unavail able

Sub

GAMMA, PED LEVEL, COLOR GAIN, DEFAULT SET GAMMA, PED LEVEL, COLOR GAIN, DEFAULT SET PED LEVEL, COLOR GAIN, DEFAULT SET

AREA1~ AREA8

OFF, ON

L_TOP, R_TOP, L_BOTTOM, R_BOTTOM

AREA1~ AREA12

ON, OFF

GREEN, RED, BLUE, BLACK, WHITE, GRAY

1~10

Page 2

Summary

Max 16x digital zoom available (Default : X1.0) Change the color of OSD (Default : Blue, 5 color is available) The image outline will be strong and clear according to sharpness level increasing(Default : 13) If this function is Off, it may looks like un-focused Save the value then move back to previous menu

You can change the settings value of video appropriate to your monitor

Display the camera's title on the screen(Max. 15ch aracter, position adjustable)

Setting the phase is selec table when used 24V AC(Dual power only) When sensitivity number is high, also motion detection sensitivity will increase Determines whether to use the MD area selected in SENSITIVITY

Determines which of the 4 vertices of each MD area is to b e used

Determines the coordinate of t he horizontal axis for SEL POS Determines the coordinate of the vertical axis for SEL POS Fill the color in selected area(The color of filling is sequentially s elected as brown, orange , blue, cyan, yellowis h green, ye llow, magenta and red.) Save the value then move back to previous menu

Make a zone for your privacy You can select privacy zone up to 12 area

Save the value then move back to previous menu

This function can be mitigates image movement from external factors

Select this to save the special menu settings and return to the main menu

3B05753D