Speco HT7815DNV, HT7915DNV, HT7815DNVW, HT7915DNVW User Manual

HT7815DNV (Grey Housing) HT7815DNVW (White Housing) HT7915DNV (Grey Housing) HT7915DNVW (White Housing)
560 Line Color Bullet Camera Weatherproof, Day/Night High Resolution Wall & Ceiling Mountable
Please read this manual thoroughly before operation and keep it handy for further reference.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL._______________
The lighting flash with an arrowhead symbol, within an equilateral triangle is
Intended to alert the user to the presence of un-insulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons____________________________________
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (serving) instructions
in the literature accompanying the appliance__________________
INFORMATION -This equipment has been tested and found to company with
limits for a class a digital device Pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
Interference When the equipments operated in a commercial environment.
This equipment generates, uses, and Can Radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may Cause
Harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which
Case the user will be required to correct the interference at his own expense.
WARNING – Change or modification not expressly approved by the manufacturer could void
the user’s authority to operate the equipment__________________________________
CAUTION : To prevent electric shock and risk of fire hazards.
DO NOT use power sources other than that specified.______
DO NOT expose this appliance to rain or moisture.000
This installation should be made by a qualified service person and should conform to all local codes.
2
CONTENTS
Package Contents
Precautions
Features
Camera Installation
LED Pattern
Specifications
4
5
6
7-12
13
14
Dimensions
Warranty
15
16
3
PACKAGE CONTENTS
Please make sure that the following items are included
in the package:
1 HT7815 (7915) Camera Series
4 Mounting Screws
1 Video test Connector
1 Wrench
Please leave this manual with the end-user for future
reference.
4
PRECAUTIONS
THIS CAMERA SHOULD BE ONLY INSTALLED BY QUALIFIED
PERSONNEL
TO PREVENT A FIRE OR ELECTRICAL HAZARD PLEASE USE
PROPER POWER CABLE
DO NOT CLEAN THE COVER WITH AN ABRAISIVE CLEANING
MATERIAL - PLEASE USE A SOFT CLOTH OR TISSUE TO CLEAN THE COVER
THERE ARE NO USER-SERVICEABLE PARTS INSIDE.
PLEASE DO NOT DISASSEMBLE THIS CAMERA OTHER THAN TO MAKE INITIAL ADJUSTMENTS
PLEASE USE A UL APPROVED REGULATED 24 VOLT AC OR
12 VOLT DC POWER SUPPLY
PLEASE USE APPROPRIATE LOW VOLTAGE POWER CABLE
TO PREVENT FIRE OR ELECTRICAL SHOCK
PLEASE INSURE THAT YOUR INSTALLATION AREA CAN
SUPPORT THE WEIGHT OF THE CAMERA
PLEASE HANDLE THIS CAMERA CAREFULLY:
- DON’T USE A STRONG OR ABRASIVE DETERGENT WHEN CLEANING THE CAMERA.
- DON’T EXPOSE THE CAMERA TO DIRECT SUN
5
FEATURES
1/3” SONY Super-Had HQ-1* CCD, 560TVL HQ-1 DSP
External lens control of zoom and focus
Split Glass Technology eliminates IR reflections
48 Mini IR LEDS (150’ Range – HT7815DNV/W)
24 IR LEDs + 6 Super IR LEDs (330’ Range – HT7915DNV/W)
Mechanical day/night IR cut filter
Lux level dip switch controls when the camera switches
into B/W Mode - CDS Sensor
UTP function built-in for use with twisted pair wiring
in addition to standard coax
Day/night DC Varifocal auto iris lens (2.8 ~ 12mm)
Video test connector for easy installation
Dual voltage operation
Weatherproof sunshield
Built-in heater extends operating range
and eliminates condensation
Easy access bottom panel controls (BLC, ELC, F/L, L/L)
Insulated mount reduces ground loops
Cable runs through the mount for protection
6
CAMERA INSTALLATION
CONNECT POWER CABLE
1. WHEN USING 12 VOLTS DC (constant voltage 500 mA)
Power Input :RED
Center : (+)
DC 12V Power Supply
2. WHEN USING 24 VOLTS AC (40 Volt Amps)
RED(+)
AC 24V
BLACK:(-)
Power Supply
3. CONNECT VIDEO CABLE
-Connect BNC Cable To The BNC Jack.
4. UTP OUTPUT
-Allows use of the camera with Cat-5E or UTP cable. A Receiving Balun must be used on the monitor side. Please see our model VID-UTP
UTP ­UTP +
UTP – UTP +
7
CAMERA INSTALLATION
Bottom Controller Details
1.V-Phase Down
2.LED Level
3.DC Lens Level
5.Function
1. V-Phase Level (UP/Down)
When desired, the vertical phase may be adjusted to synchronize the vertical phase of the camera with other cameras in the system. This feature is only available in 24 Volt AC operation
1.V-Phase Up
4.Video Test
6.LUX Level
2.LED Level
Adjust the LED brightness
3.DC Lens Level
Fine tune the Auto IRIS Lens
4.Video Test Connector
Allows the connection of a Local Monitor to make initial adjustments to the camera
8
5.Function
* DIP SWITCH
OFF
123
4
CAMERA INSTALLATION
ON
(1)ELC
(2)BLC
(3)F/L
(4)L/L
(1) ELC- Electronic Light Compensation
ON : Camera is in Electronic Shutter Mode OFF: Electronic Shutter is fixed at 1/60 and Auto Iris mode
is active
(2) BLC-Back Light Compensation.
BLC: If there is a strong light behind an object
the object may appear as a shadow. Activating the BLC will minimize this effect. The Coverage of the BLC is center plus bottom.
(3) F/L- Flicker-Less
ON : Use when the LUX changes often OFF: Use under normal circumstances
(4) L/L- Line Lock
Locks the camera to the 60 Hz of the wall outlet. Only operates in the 24 Volt AC mode
9
CAMERA INSTALLATION
6. LUX DIP SWITCH
:
Tells the camera when to switch to the B/W night mode.
: Only one switch can be in the “on”position at a time.
OFF
ON
12
#1 STEP - The camera will switch at 1/2 lux
#2 STEP - The camera will switch at 1 lux
3
#3 STEP - The camera will switch at 3 lux
4
#4 STEP - The camera will switch at 5 lux
Zoom & Focus Adjustment
VIDEO COLOR CCD CAMERA
- Loosen the fixed screws in each ring of Focus & Zoom properly and adjust zoom or focus ring to take a right picture and then fix the set screw again.
- Be careful of not putting too much strength when adjustment.
ZOOM CONTROLLER
FOCUS CONTROLLER
10
CAMERA INSTALLATION
COMPATIBILITY
CVCTPEXT“A” type Box “B” type Box
CVCTPLATE
Original Mounting
Flange Should be removed to use the CVCTPLATE
[CVCTPLATE Hole Description]
Hole 1 : CVCTPEXT
Hole 2 : Electrical Box “B” type
Hole 3 : Electrical Box “A” type
11
CAMERA INSTALLATION
COMPATIBILITY
BCP
( USING 7246WMT
CVCTPEXT
CVCTPLATE
)
BCP (Direct connection )
12
LED PATTERN
HT7815DNV (W)
2.8-12mm VF lens 48 Mini IR LEDs (150’ Range)
HT7915DNV (W)
5-50mm VF lens 24 IR LEDs + 6 Super IR LEDs (330’ Range)
13
SPECIFICATIONS
ITEM HT7815DNY & HT7915DNY Series
Image Sensor 1/3” Sony Super-Had HQ-1* DSP CCD
Resolution 560 TV Line
Minimum illumination 0.03lux (IP Off) 0.00 LUX (IR on)
Lens Type
CDS Sensor Photoconductive Cells, Adjustable
Electronic Shutter
Video Output 1.0vp-p into 75 ohms composite
TV System NTSC
Scanning System 2 : 1 Interlace
Sync System Line Locked / Adjustable V-Phase. Line Lock/Internal On-Off
S/N Ratio More than 60db
IR Cut Filter Mechanical – Auto Adjusts when required
Power Supply 24 Volts AC, 12 Volts DC – Dual Voltage
Power consumption 550mA (HT7815), 650mA (HT7915)
Operating Temperature - 29~ +50( - 20℉ ~122℉)
Day / Night DC Auto Iris Varifocal Lens
2.8-12mm (HT7815) / 5-50mm(HT7915)
1/60 – 1/1000,000 seconds
Operating Humidity 30%~90%RH
Weight 3 lbs
Warranty 5Years
14
HT7815DNV Series
DIMENSIONS
Front View
HT7915DNV Series
Front View
Side View
Side View
15
WARRANTY
16
MEMO
MEMO
MEMO
Speco Technologies is constantly developing product improvements. We reserve the right to modify product design and specifications without notice and without incurring any obligation.
200 New Highway
Amityville, NY 11701
631-957-8700
www.specotech.com
Rev. 100120
Loading...