Speco HT7246IHR,HT7247IHR,HT7250IHR,HTINTB8,HTINTB9,HTINTB10,HTINTD8,HTINTD9,HTINTD10,HT647HRTP,CVC6245IHR,CVC6246IHR,HTINTT5 Instruction Manual

Page 1
INSTRUCTION MANUAL
650Line Intensier3™ Series
Speco Technologies is constantly developing product improvements. We reserve the right to modify product design and specifications without notice and without incurring any obligation.
Rev. 6/20/2012
(Weatherproof Dome Camera with Chameleon™ Cover)
HTINTB8 / HTINTB9 / HTINTB10
(Weatherproof Bullet Camera with mount plate)
HTINTD8 / HTINTD9 / HTINTD10
(Weatherproof Dome Camera)
HT647HRTP
(Miniature Weatherproof Dome Camera with Chameleon™ Cover)
CVC6245IHR
(Indoor Wall & Ceiling Mount Dome Camera)
CVC6246IHR
(Indoor Wall & Ceiling Mount Dome Camera)
HTINTT5
(Traditional Box type Camera)
Page 2
Contents
1
Contents ...................................................... 1
Precautions ................................................. 2, 3
Safety Instructions ...................................... 4
Package Contents ....................................... 5
Camera Installation ..................................... 6-13
Specications .............................................. 14-20
Camera Dimension ..................................... 21-23
Features ...................................................... 24-25
OSD Menu Details ...................................... 26- 37
Trouble Shooting ......................................... 38
Page 3
2
Precautions
Do not install the camera in extreme temperature conditions.
Do not touch the front lens of the camera.
Never keep the camera pointed directly at strong light.
Do not expose the camera to radioactivity.
Do not install the camera under unstable lighting conditions.
Do not drop the camera or subject it to physical shocks.
Only use the camera under conditions where temperatures are between
-10°C and +50°C. Be especially careful to provide ventilation when operating under high temperatures.
This is one of the most important parts of the camera. Be careful not to leave fingerprints on the lens cover.
It can cause malfunctions to occur.
If exposed to radioactivity the CCD will fail.
Severe lighting change or flicker can cause the camera to work improperly.
Housing damage can compromise weatherproof ratings.
NOTE
* If the camera is exposed to spotlight or object reflecting strong light,
smear or blooming may occur.
* please check that the power satisfies the normal specification before
connecting the camera.
Page 4
3
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ISO14001
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ISO14001
The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ISO14001
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.
WARNING - Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than those specified.
In USA and Canada, Use Class 2 Power Supply Only
Page 5
4
Safety Instructions
Precautions for use
Please handle this camera carefully :
This camera should be installed by qualied personnel only
There are no user serviceable parts inside
Do not disassemble this camera other than to make initial adjustments
Use a UL approved regulated 24 volt AC or 12 volt DC power supply
Use appropriate low voltage power cable to prevent re or electrical shock
Please insure that your installation area can support the weight of the camera
Do not use a strong or abrasive detergent when cleaning the camera
Do not install near cooling or heating device
Page 6
5
Package Contents
Please make sure that the following items are included in the Package:
1) HT7246IHR, HT7247IHR, HT7250IHR
• 1 Video Test Connector, Power Jack
• 1 Chameleon Cover
• 1 Wrench
• Set Screw
- 3 Tapping Screws 4x40
- 3 Plastic Anchor
2) HTINTB8, HTINTB9, HTINTB10
• 1 Video Test Connector, Power Jack
• 1 Bracket Base
• 2 Wrenches
• Set Screw
- 4 Tapping Screws 4x25
- 4 Hexagon Socket Screws 5x10
3) HTINTD8, HTINTD9, HTINTD10
• 1 Video Test Connector, Power Jack
• 2 Wrenches
• Set Screw
- 3 Tapping Screws 4x25
- 2 Hexagon Socket Screws M6x20
4) HT647HRTP
• 1 Chameleon Cover
• 1 Video Test Connector, Power Jack
• 1 Wrench
• Set Screw
- 3 Tapping Screws 3x40
5) CVC6245IHR, CVC6246IHR
• 1 Video Test Connector, Power Jack
• 2 Screws
- 2 Tapping Screws 4x20
6) HTINTT5
• 1 Foot HD Box Camera
• 1 C-Ring
• 1 Jack HD Box Camera Iris
• 2 Screws
• 1 Power Jack
Page 7
6
CAMERA INSTALLATION
jvuulj{Gwv~lyGjhislG
XUG~oluG|zpunGXYG}vs{zGkjGOGG\WWGhPG
YUG~oluG|zpunGY[G}vs{zGhjGO[WG}GhP
ZUGjvuulj{G}pklvGjhislG
Tjvuulj{GiujGjhislG{vG{olGiujGqhjrUG
[UGjvuulj{GhGGOyGP
TjGORGSGjvtPGGwGGGOTUGjvtPGG
uGGGlGhGkGGtG kGG˄vu˅GGGU
kjGXY}GwGz
wGpGaylk
jGaGORP
ishjraOTP
ylkORP
wGz
hjGY[}
R
T
jvtG
hGvG
wGhGk G
uGhGk
Page 8
7
CAMERA INSTALLATION
Compatibility
1) HT7246IHR, HT7247IHR, HT7250IHR
2) HTINTB8, HTINTB9, HTINTB10
INTWM
CVCJBB
INTPM
INTJBS
CVCJBD
INTCM
DFM
Page 9
8
CAMERA INSTALLATION
Compatibility
3) HTINTD8, HTINTD9, HTINTD10
4) CVC6245IHR, CVC6246IHR
INTWM
DFM
INTPM JB03TG
Page 10
CAMERA INSTALLATION
9
1. HT7246IHR / HT7247IHR / HT7250IHR
CAUTION : The installation instructions in this manual are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
VANDAL DOME BODY ASSEMBLY
BODY OUTER COVER
TAPPING SCREW 4X40, 3EA
VANDAL DOME BASE ASSEMBLY
PLASTIC ANCHOR 6x30, 3EA
Page 11
CAMERA INSTALLATION
10
2. HTINTB8, HTINTB9, HTINTB10
CAMERA ASSEMBLY
HEXAGON SOCKET SCREW M5X10, 4EA
TAPPING SCREW 4X25, 4EA
BASE ADAPTOR BRACKET
Page 12
CAMERA INSTALLATION
11
3. HTINTD8, HTINTD9, HTINTD10
DOME BASE
HEXAGON SOCKET SCREW M6X20, 2EA
DOME ASSEMBLY
DOME BODY
TAPPING SCREW 4X25, 3EA
Page 13
CAMERA INSTALLATION
12
4. HT647HRTP
TAPPING SCREW 3X40, 3EA
BODY & DOME COVER ASSEMBLY
BASE & ROTATE BRACKET ASSEMBLY
Page 14
CAMERA INSTALLATION
13
5. CVC6245IHR, CVC6246IHR
TAPPING SCREW 4X20, 2EA
DOME COVER ASSEMBLY
BASE ASSEMBLY
Page 15
14
SPECIFICATIONS
650 Line Intensifier3
(Weatherproof Dome Camera with Chameleon™ Cover)
DC Auto Iris Varifocal Lens 2.8-12mm / 9-22mm / 5-50mm
MODEL
HT7246IHR / HT7247IHR / HT7250IHR
1/3” Sony Super HAD ll CCD NTSC, PAL NTSC=811(H) * 508(V) / PAL=795(H) * 596(V) NTSC=768(H) * 494(V) / PAL=752(H) * 582(V) NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V) 2:1 Interlace Internal 650TV Lines CDS OFF: 0.15 Lux, CDS ON: 0.00002 Lux More than 52dB CVBS: 1.0Vp-p / 75Ω NTSC=(1/60sec~1/120,000sec) / PAL=(1/50sec~1/120,000sec) Available On / Off (Level adjustable) BLC / HLC / OFF Color / BW / AUTO Low / High / Off ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K) Auto / Off (Selectable x2 ~ x512) On / Off (8 Programmable Zones) On / Off (12 Programmable Zones) On / Off (Level adjustable) On / Off (x1 ~ x16) On / Off On / Off (Level adjustable) On / Off DC 12V / AC24V(Dual Voltage) DC 12V 250mA / AC24V 100mA DC Auto Iris Varifocal Lens 2.8-12mm / 9-22mm / 5-50mm
-4ºF~140ºF RH 95% Max
-4ºF~140ºF RH 95% Max
5.10"(Dia) * 3.46"(H) 1 lbs
Image Pick-Up Device TV System Total Pixels Effective Pixels Scanning Frequency Scanning System Synchronization Resolution Minimum Illumination S/N Ratio Video Output Electronic Shutter Speed OSD WDR BLC Day & Night Gain Control White Balance Intensify Motion Detection Privacy Masking SPECO DNR Digital Zoom DIS (Digital Image Stabilization) Sharpness Flip / Mirror Power Supply Power Consumption Lens Operational Temp. Storage Temp. Dimension Weight
HT7246IHR (2.8-12mm) HT7247IHR (9-22mm) HT7250IHR (5-50mm)
Page 16
15
650 Line Intensifier3
(Weatherproof Bullet Camera with mount plate)
DC Auto Iris Varifocal Lens 2.8-12mm / 5-50mm / 9-22mm
HTINTB8 / HTINTB8W
(2.8-12mm)
HTINTB9 / HTINTB9W
(5-50mm)
HTINTB10 / HTINTB10W
(9-22mm)
SPECIFICATIONS
MODEL
HTINTB8 / HTINTB9 / HTINTB10
1/3” Sony Super HAD ll CCD NTSC, PAL NTSC=811(H) * 508(V) / PAL=795(H) * 596(V) NTSC=768(H) * 494(V) / PAL=752(H) * 582(V) NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V) 2:1 Interlace Internal 650TV Lines CDS OFF: 0.15 Lux, CDS ON: 0.00002 Lux More than 52dB CVBS: 1.0Vp-p / 75Ω NTSC=(1/60sec~1/120,000sec) / PAL=(1/50sec~1/120,000sec) Available On / Off (Level adjustable) BLC / HLC / OFF Color / BW / AUTO Low / High / Off ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K) Auto / Off (Selectable x2 ~ x512) On / Off (8 Programmable Zones) On / Off (12 Programmable Zones) On / Off (Level adjustable) On / Off (x1 ~ x16) On / Off On / Off (Level adjustable) On / Off DC 12V / AC24V(Dual Voltage) DC 12V 400mA / AC24V 170mA DC Auto Iris Varifocal Lens 2.8-12mm / 5-50mm / 9-22mm
-4ºF~140ºF RH 95% Max
-4ºF~140ºF RH 95% Max
3.46"(W) * 4.01"(H) * 11.02"(D) 3 lbs
Image Pick-Up Device TV System Total Pixels Effective Pixels Scanning Frequency Scanning System Synchronization Resolution Minimum Illumination S/N Ratio Video Output Electronic Shutter Speed OSD WDR BLC Day & Night Gain Control White Balance Intensify Motion Detection Privacy Masking SPECO DNR Digital Zoom DIS (Digital Image Stabilization) Sharpness Flip / Mirror Power Supply Power Consumption Lens Operational Temp. Storage Temp. Dimension Weight
Page 17
16
650 Line Intensifier3
(Weatherproof Dome Camera)
DC Auto Iris Varifocal Lens 2.8-12mm / 5-50mm / 9-22mm
HTINTD8 / HTINTD8W
(2.8-12mm)
HTINTD9 / HTINTD9W
(5-50mm)
HTINTD10 / HTINTD10W
(9-22mm)
SPECIFICATIONS
MODEL
HTINTD8 / HTINTD9 / HTINTD10
1/3” Sony Super HAD ll CCD NTSC, PAL NTSC=811(H) * 508(V) / PAL=795(H) * 596(V) NTSC=768(H) * 494(V) / PAL=752(H) * 582(V) NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V) 2:1 Interlace Internal 650TV Lines CDS OFF: 0.15 Lux, CDS ON: 0.00002 Lux More than 52dB CVBS: 1.0Vp-p / 75Ω NTSC=(1/60sec~1/120,000sec) / PAL=(1/50sec~1/120,000sec) Available On / Off (Level adjustable) BLC / HLC / OFF Color / BW / AUTO Low / High / Off ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K) Auto / Off (Selectable x2 ~ x512) On / Off (8 Programmable Zones) On / Off (12 Programmable Zones) On / Off (Level adjustable) On / Off (x1 ~ x16) On / Off On / Off (Level adjustable) On / Off DC 12V / AC24V(Dual Voltage) DC 12V 400mA / AC24V 170mA DC Auto Iris Varifocal Lens 2.8-12mm / 5-50mm / 9-22mm
-4ºF~140ºF RH 95% Max
-4ºF~140ºF RH 95% Max
5.47"(Dia) * 4.36"(H)
3.08 lbs
Image Pick-Up Device TV System Total Pixels Effective Pixels Scanning Frequency Scanning System Synchronization Resolution Minimum Illumination S/N Ratio Video Output Electronic Shutter Speed OSD WDR BLC Day & Night Gain Control White Balance Intensify Motion Detection Privacy Masking SPECO DNR Digital Zoom DIS (Digital Image Stabilization) Sharpness Flip / Mirror Power Supply Power Consumption Lens Operational Temp. Storage Temp. Dimension Weight
Page 18
17
650 Line Intensifier3
(Miniature Weatherproof Dome Camera with Chameleon™ Cover)
3.6mm Fixed Board Lens
HT647HRTP
(3.6 Fixed Board Lens)
SPECIFICATIONS
MODEL
HT647HRTP
1/3” Sony Super HAD ll CCD NTSC, PAL NTSC=811(H) * 508(V) / PAL=795(H) * 596(V) NTSC=768(H) * 494(V) / PAL=752(H) * 582(V) NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V) 2:1 Interlace Internal 650TV Lines CDS OFF: 0.15 Lux, CDS ON: 0.00002 Lux More than 52dB CVBS: 1.0Vp-p / 75Ω NTSC=(1/60sec~1/120,000sec) / PAL=(1/50sec~1/120,000sec) Available On / Off (Level adjustable) BLC / HLC / OFF Color / BW / AUTO Low / High / Off ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K) Auto / Off (Selectable x2 ~ x512) On / Off (8 Programmable Zones) On / Off (12 Programmable Zones) On / Off (Level adjustable) On / Off (x1 ~ x16) On / Off On / Off (Level adjustable) On / Off DC 12V DC 12V 250mA
3.6mm Fixed Board Lens
-4ºF~140ºF RH 95% Max
-4ºF~140ºF RH 95% Max
4.33"(Dia) * 3.14"(H)
1.54 lbs
Image Pick-Up Device TV System Total Pixels Effective Pixels Scanning Frequency Scanning System Synchronization Resolution Minimum Illumination S/N Ratio Video Output Electronic Shutter Speed OSD WDR BLC Day & Night Gain Control White Balance Intensify Motion Detection Privacy Masking SPECO DNR Digital Zoom DIS (Digital Image Stabilization) Sharpness Flip / Mirror Power Supply Power Consumption Lens Operational Temp. Storage Temp. Dimension Weight
Page 19
18
650 Line Intensifier3
(Indoor Wall & Ceiling Mount Dome Camera)
DC Auto Iris Varifocal Lens 2.8-12mm
CVC6245IHR / CVC6245IHRW
(2.8-12mm)
SPECIFICATIONS
MODEL
CVC6245IHR / CVC6245IHRW
1/3” Sony Super HAD ll CCD NTSC, PAL NTSC=811(H) * 508(V) / PAL=795(H) * 596(V) NTSC=768(H) * 494(V) / PAL=752(H) * 582(V) NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V) 2:1 Interlace Internal 650TV Lines CDS OFF: 0.15 Lux, CDS ON: 0.00002 Lux More than 52dB CVBS: 1.0Vp-p / 75Ω NTSC=(1/60sec~1/120,000sec) / PAL=(1/50sec~1/120,000sec) Available On / Off (Level adjustable) BLC / HLC / OFF Color / BW / AUTO Low / High / Off ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K) Auto / Off (Selectable x2 ~ x512) On / Off (8 Programmable Zones) On / Off (12 Programmable Zones) On / Off (Level adjustable) On / Off (x1 ~ x16) On / Off On / Off (Level adjustable) On / Off DC 12V DC 12V 250mA DC Auto Iris Varifocal Lens(2.8mm-12mm)
-4ºF~140ºF RH 95% Max
-4ºF~140ºF RH 95% Max
5.51"(Dia) * 4.09"(H)
1.54 lbs
Image Pick-Up Device TV System Total Pixels Effective Pixels Scanning Frequency Scanning System Synchronization Resolution Minimum Illumination S/N Ratio Video Output Electronic Shutter Speed OSD WDR BLC Day & Night Gain Control White Balance Intensify Motion Detection Privacy Masking SPECO DNR Digital Zoom DIS (Digital Image Stabilization) Sharpness Flip / Mirror Power Supply Power Consumption Lens Operational Temp. Storage Temp. Dimension Weight
Page 20
19
650 Line Intensifier3
(Indoor Wall & Ceiling Mount Dome Camera)
DC Auto Iris Varifocal Lens 2.8-12mm
CVC6246IHR / CVC6246IHRW
(2.8-12mm)
SPECIFICATIONS
MODEL
CVC6246IHR / CVC6246IHRW
1/3” Sony Super HAD ll CCD NTSC, PAL NTSC=811(H) * 508(V) / PAL=795(H) * 596(V) NTSC=768(H) * 494(V) / PAL=752(H) * 582(V) NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V) 2:1 Interlace Internal 650TV Lines CDS OFF: 0.15 Lux, CDS ON: 0.00002 Lux More than 52dB CVBS: 1.0Vp-p / 75Ω NTSC=(1/60sec~1/120,000sec) / PAL=(1/50sec~1/120,000sec) Available On / Off (Level adjustable) BLC / HLC / OFF Color / BW / AUTO Low / High / Off ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K) Auto / Off (Selectable x2 ~ x512) On / Off (8 Programmable Zones) On / Off (12 Programmable Zones) On / Off (Level adjustable) On / Off (x1 ~ x16) On / Off On / Off (Level adjustable) On / Off DC 12V / AC24V(Dual Voltage) DC 12V 250mA / AC24V 100mA DC Auto Iris Varifocal Lens(2.8mm-12mm)
-4ºF~140ºF RH 95% Max
-4ºF~140ºF RH 95% Max
5.51"(Dia) * 4.09"(H)
1.54 lbs
Image Pick-Up Device TV System Total Pixels Effective Pixels Scanning Frequency Scanning System Synchronization Resolution Minimum Illumination S/N Ratio Video Output Electronic Shutter Speed OSD WDR BLC Day & Night Gain Control White Balance Intensify Motion Detection Privacy Masking SPECO DNR Digital Zoom DIS (Digital Image Stabilization) Sharpness Flip / Mirror Power Supply Power Consumption Lens Operational Temp. Storage Temp. Dimension Weight
Page 21
20
650 Line Intensifier3
(Traditional Box type Camera)
C&CS Mount Lens
HTINTT5
(C&CS Mount Lens)
SPECIFICATIONS
MODEL
HTINTT5
1/3” Sony Super HAD ll CCD NTSC, PAL NTSC=811(H) * 508(V) / PAL=795(H) * 596(V) NTSC=768(H) * 494(V) / PAL=752(H) * 582(V) NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V) 2:1 Interlace Internal 650TV Lines CDS OFF: 0.15 Lux, CDS ON: 0.00002 Lux More than 52dB CVBS: 1.0Vp-p / 75Ω NTSC=(1/60sec~1/120,000sec) / PAL=(1/50sec~1/120,000sec) Available On / Off (Level adjustable) BLC / HLC / OFF Color / BW / AUTO Low / High / Off ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K) Auto / Off (Selectable x2 ~ x512) On / Off (8 Programmable Zones) On / Off (12 Programmable Zones) On / Off (Level adjustable) On / Off (x1 ~ x16) On / Off On / Off (Level adjustable) On / Off DC 12V / AC24V(Dual Voltage) DC 12V 250mA / AC24V 100mA C&CS Mount Lens
-4ºF~140ºF RH 95% Max
-4ºF~140ºF RH 95% Max
2.51"(W) * 2.20"(H) * 3.46"(D)
0.88 lbs
Image Pick-Up Device TV System Total Pixels Effective Pixels Scanning Frequency Scanning System Synchronization Resolution Minimum Illumination S/N Ratio Video Output Electronic Shutter Speed OSD WDR BLC Day & Night Gain Control White Balance Intensify Motion Detection Privacy Masking SPECO DNR Digital Zoom DIS (Digital Image Stabilization) Sharpness Flip / Mirror Power Supply Power Consumption Lens Operational Temp. Storage Temp. Dimension Weight
Page 22
21
CAMERA DIMENSION
1) HT7246IHR, HT7247IHR, HT7250IHR
2) HTINTB8, HTINTB9, HTINTB10
1.16”
5.10” dia
5.10” dia
3.93” dia
3.46”
3.46”
4.01”
3.11”
3.89” dia
11.02”
5.90”
5.03”
10.51”
Page 23
22
CAMERA DIMENSION
3) HTINTD8, HTINTD9, HTINTD10
4) HT647HRTP
5.47” dia
4.36”
3.34”
3.70”
1.41”
4.33” dia
3.22” dia
4.33” dia
3.14”
Page 24
23
CAMERA DIMENSION
5) CVC6245IHR, CVC6246IHR
6) HTINTT5
1.25”
4.09”
5.51” dia
4.60” dia
5.51” dia
2.51”
3.46”
3.26”
2.20”
1.49” dia
Page 25
24
FEATURES
Now with “PRESETS”
PRESETS (Outdoor, Indoor, Elevator, Lobby, Hallway & Low Light) Used for a quick and easy setup for the installation environment.
650TVL Resolution
Horizontal resolution of 650 TV lines is achieved by using a SONY Super-HAD CCD with 410,000 pixels, and a custom DSP yielding pictures with a high S/N ratio.
INTENSIFIER 3
More Powerful Performance in low light condition. High quality Pictures to be captured in very low light condition.
WDR
More Powerful WDR in strong back lighting. Your camera allows you to get a clear image.
SPECO DNR
The Intensier camera has a DSP chip that can remove image noise efciently showing clean images in low light conditions.
HLC (High Light Compensation)
This function reverses bright spots in the picture (such as headlights). This enables the entire system to do a better job of resolving and displaying grayscale information such as a license plate.
Page 26
25
FEATURES
Motion Detection with Alarm Output
Built in motion detector with adjustable areas of coverage will Send a signal to an external alarm device when motion is detected.
Privacy Mask
It also has the ability to mask up to 8 areas of the picture where Viewing is not desired. Each zone can be independently programmed via the OSD
Stabilizer
This function removes image jitter that is caused by vibrations in the building and reduces the amount of hard drive space.
Digital Zoom
The picture could be enlarged by this function in digital.
Day/Night
The Intensier camera can show color pictures in all lighting
conditions, or you can have it automatically swiches to a B/W picture in low light conditions
OSD
All camera functions are menu driven for easy use.
Page 27
26
Menu Setup
Lens Setting
1. Press the Function Setup switch.
- Main setup menu is displayed on the monitor screen.
1. Preset :
INDOOR / OUTDOOR / LOW LIGHT / HALLWAY / LOBBY / ELEVATOR.
- Used for a quick and easy setup for the installation environment.
Using this function, you can control the screen brightness.
1. When the SETUP menu screen is displayed, select 'LENS' by using the Function Setup switch so that the arrow indicates 'LENS'.
2. DC : You can adjust the minimum shutter and maximum value of ESC shutter mode.
2. Select a desired function using the Function Setup switch.
- Place the cursor over a desired item.
3. Set up a selected item by using the Function Setup switch.
4.
To finish the setting, select 'RETURN' and press the Function Setup switch.
Preset Mode
SPECO TECH
1.PRESET MODE
2.MAIN SETUP
3.EXIT
INDOOR
RESET
MAIN SETUP
1.LENS
2.EXPOSURE
3.WHITE BAL
4.WDR
5.BACKLIGHT
6.SPECO DNR
7.DAY/NIGHT
8.SPECIAL
9.RETURN
DC
ATW OFF OFF ON AUTO
SAVE
NOTE
■ An item with the
icon also has sub menus. To select a sub menu, select an item
with the icon and press the Function Setup switch.
■ An item with the - - - icon is unavailable due to function settings.
Page 28
27
3. THE Lens mode has sub menu items as listed below.
- BRIGHTNESS : Adjusts the video brightness.
-
FOCUS ADJ : To adjust the DC lens focus correctly, you must activate the Focus Settings mode under each
lens menu. Activate the Focus Settings mode, adjust the lens focus, and then deactivate the settings mode.
NOTE
■ If color rolling occurs when using a DC lens, set Shutter to Fixed (---).
Exposure Setting
1. When the SETUP menu screen is displayed, select 'EXPOSURE' by using the Function Setup Switch.
2. Select a desired mode using the Function Setup switch.
SHUTTER : You can select either auto or manual shutter. * --- : Shutter speed is fixed at 1/60sec(1/50sec) * ESC : Select this to control the shutter speed automatically. If ESC is selected, the shutter speed is automatically controlled depending on the ambient illumination of the subject. * MANUAL : You can control shutter speed manually. (NTSC MODEL : 1/60~1/120,000, PAL MODEL : 1/50~1/120,000) * A.FLK : Select this when you see picture flicker, this can happen when the frequency of the local lighting clashes with the camera.
MAIN SETUP
1.LENS
2.EXPOSURE
3.WHITE BAL
DC
ATW
EXPOSURE SETUP
1.BRIGHTNESS
2.SHUTTER
3.AGC
4.INTENSIFY
5.RETURN
25
- - -
HIGH
OFF
MAIN SETUP
1.LENS
2.EXPOSURE
3.WHITE BAL
DC
ATW
Page 29
28
FUTO GAIN CONTROL) : The higher the gain level, the brighter the screen
- but the higher the noise. * OFF : Deactivates the AGC function. * LOW : Allows automatic gain control from 5.3dB to 32dB. * HIGH : Allows automatic gain control from 5.3dB to 37dB.
INTENSIFY : When it is night or dark, the camera automatically detects the light level and maintains a clear picture if this mode is activated. * OFF : Deactivates the INTENSIFY function. * AUTO : Activates the INTENSIFY function.
RETURN : Select this to save the changes in the EXPOSURE menu and return to the SETUP menu.
NOTE
■ If you press the Function Setup switch to ‘AUTO’ mode, you can adjust brightness by increasing or decreasing the shutter speed. (x2 ~ x512)
■ Note that the higher the zoom level, the brighter the screen, but the more likely there will be a ghosting effect.
■ It is normal for Noise, Spots and Whitish symptoms to appear in INTENSIFY mode when the D-ZOOM level is increased.
White Balance (White Bal) Setting
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select 'White Bal' by using the Function Setup switch so that the arrow indicates 'White Bal'.
2. Select a desired mode using the Function Setup switch.
MAIN SETUP
1.LENS
2.EXPOSURE
3.WHITE BAL
DC
ATW
NOTE
■ When the SHUTTER is set to MANUAL or A.FLK mode, INTENSIFY will be disabled.
Page 30
29
※Select one of the following 5 modes, as appropriate for your purpose.
ATW : Select this when the color temperature is between 1,700˚K and 11,000˚K.
OUTDOOR : Select this when the color temperature is between 1,700˚K and 11,000˚K.
(sodium light inclusion)
INDOOR : Select this when the color temperature is between 4,500˚K and 8,500˚K.
MANUAL : Select this to fine-tune White Balance manually. Set White Balance first by using the ATW or AWC mode. After that switch to MANUAL mode, fine-tune the White Balance and then press the Function Setup switch.
AWC→SET : To find the optimal luminance level for the current environment, point the camera towards a sheet of white paper and press the Function Setup switch. If the environment changes, readjust it.
NOTE
■ White Balance may not work properly under the following conditions. In this case select the AWC mode.
When the color temperature of the environment surrounding the subject is out of the
control range (e.g. clear sky or sunset).
When the ambient illumination of the subject is dim.
If the camera is directed towards a uorescent light or is installed in a place where
illumination changes dramatically, the White Balance operation may become unstable.
WDR Setting
WDR illuminates darker spots of an image while retaining the same light level for brighter spots to even out the overall brightness of images with high contrast between bright and dark spots.
MAIN SETUP
1.LENS
2.EXPOSURE
3.WHITE BAL
4.WDR
DC
ATW OFF
1. When the SETUP menu screen is displayed, select 'WDR' by using the switch so that the arrow indicates 'WDR'.
2. Use the switch to change the WDR level according to the contrast between bright and dark areas.
Page 31
30
Backlight Setting
Unlike conventional cameras, the 650Line Intensifier3™ Series are designed to deliver a distinctive subject and background at the same time, even when the subject is backlight, by using the features of the proprietary W-V DSP chip.
1. When the SETUP menu screen is displayed, select 'BACKLIGHT' by using the Function Setup switch so that the arrow indicates 'BACKLIGHT'.
2. Select a desired mode using the Function Setup switch.
BLC : Enables a user to directly select a desired area from a picture, and to view the area more clearly.
HLC (High Light Compensation) : If the scene contains extremely bright light areas such as; from car headlights, the light can mask out much of the on-screen detail
- LEVEL : Adjust level of the HLC function.
- LIMIT : Enable to change the operating condition.
- MASK COLOR/TONE : Change the color / transparency of the masking area. (Black, Red, Blue, Cyan, Magenta)
- TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced
OFF : Not being used
3. Select a desired mode using the Function Setup switch and press the Function Setup switch.
u
Select 'BLC' to adjust the area to be enhanced then adjust the level.
MAIN SETUP
1.LENS
2.EXPOSURE
3.WHITE BAL
4.WDR
5.BACKLIGHT
6.SPECO DNR
7.DAY/NIGHT
8.SPECIAL
9.RETURN
DC
ATW OFF OFF ON AUTO
SAVE
Page 32
31
BLC SETUP HLC SETUP
Press Set to Return
Press Set to Return
LEVEL TOP BOTTOM LEFT RIGHT
LEVEL LIMITS MASK COLOR MASK TONE TOP BOTTOM LEFT RIGHT
LOW
38
109
54
121
MIDDLE NIGHT ONLY BLACK
1 5
120
5
172
NOTE
Because there can be a difference in the effectiveness of HLC according to the amount
of light area in the screen, optimize the installation angle for the best HLC performance.
When dark, the HLC is only activated when a bright light exceeding a specic size in
NIGHT ONLY mode.
The HLC is not activated in day light or when bright light is not present at night in NIGHT
ONLY mode.
BLC Function doesn't work in the B/W mode of the DAY/NIGHT menu.
SPECO DNR Setting
This function reduces the background noise in a low luminance environment.
1. When the SETUP menu screen is displayed, select 'SPECO DNR' by using the Function Setup switch so that the arrow indicates 'SPECO DNR'.
2. Select a desired mode using the Function Setup switch.
OFF : Deactivates SPECO DNR. Noise is not reduced.
ON : Activates SPECO DNR so that noise is reduced.
MAIN SETUP
1.LENS
2.EXPOSURE
3.WHITE BAL
4.WDR
5.BACKLIGHT
6.SPECO DNR
7.DAY/NIGHT
8.SPECIAL
9.RETURN
DC
ATW OFF OFF ON AUTO
SAVE
Page 33
32
3. Set the SPECO DNR mode to 'ON' and press the Function Setup switch. Then you can adjust the noise reduction level.
NOTE
You cannot set the SPECO DNR to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is ‘OFF’.
When adjusting the noise reduction level in the SPECO DNR mode, remember that the higher
the level set, the more the noise level will be reduced, as will the brightness of the image.
Day/Night Setting
You can display pictures in color or black and white.
1. When the SETUP menu screen is displayed, select 'DAY/NIGHT'by using the Function Setup switch so that the arrow indicates 'DAY/NIGHT'.
MAIN SETUP
1.LENS
2.EXPOSURE
3.WHITE BAL
4.WDR
5.BACKLIGHT
6.SPECO DNR
7.DAY/NIGHT
8.SPECIAL
9.RETURN
DC
ATW OFF OFF ON AUTO
SAVE
2. Select a desired mode using the Function Setup Switch according to the picture display you want.
COLOR : The picture is always displayed in color.
B/W : The picture is always displayed in black and white.
- BURST MODE : You can turn on or off the burst signal on B/W mode.
B/W MODE SETUP
1.BURST MODE
2.RETURN
OFF
Page 34
33
AUTO : The mode is switched to 'Color' in a normal environment, but switches to 'B/W' mode when ambient illumination is low. To set up the switching time for AUTO mode, press
the Function Setup switch. You can turn on or off the burst signal on B/W mode.
- BURST MODE : You can turn on or off the burst signal on B/W mode.
- DURATION : You can select brightness of illumination about changing the day/night mode.
- DWELLTIME : You can select the duration time about changing the day/night mode. g3s, 5s, 7s, 10s, 15s, 20s, 30s, 40, 60s
* The day/night switching point of the camera can be adjusted.
FAST
SLOW
COLOR→B/W
2.5 lux 1 lux
B/W→COLOR
5 lux
10 lux
AUTO SETUP
1.BURST MODE
2.COLOR→B/W
DURATION DWELL TIME
3.B/W→COLOR
DURATION DWELL TIME
4.RETURN
ON
FAST
3SEC
FAST
10SEC
NOTE
When AGC in the EXPOSURE menu is 'OFF', '---' mode operates as like selecting 'COLOR'
mode and 'AUTO' mode can not be selected.
Special Setting
1. When the SETUP menu screen is displayed, select 'SPECIAL' by using the Function Setup switch so that the arrow indicates 'SPECIAL'.
MAIN SETUP
1.LENS
2.EXPOSURE
3.WHITE BAL
4.WDR
5.BACKLIGHT
6.SPECO DNR
7.DAY/NIGHT
8.SPECIAL
9.RETURN
DC
ATW OFF OFF ON AUTO
SAVE
Page 35
34
2. Select a desired mode using the Function Setup switch.
SPECIAL
IMAGE SETUP
1.IMAGE ADJ
2.MONITOR
3.CAM TITLE
4.SYNC
5.MOTION DET
6.PRIVACY
7.COMM ADJ
8.LANGUAGE
9.RETURN
1.V-REV
2.H-REV
3.D-ZOOM
4.DIS
5.FONT COLOR
6.SHARPNESS
7.RETURN
OFF
INT OFF OFF
ENGLISH
OFF OFF
WHITE
ON
IMAGE ADJ. :
1) When the SETUP menu screen is displayed, select 'IMAGE ADJ' by using the Function Setup switch so that the arrow indicates 'IMAGE ADJ'.
2) Select a desired mode using the Function Setup switch.
* V-REV : You can flip the picture vertically on the screen. * H-REV : You can flip the picture horizontally on the screen. * D-ZOOM : You can use a digital zoom of x1 ~ x16. * DIS (Digital Image Stabilizer) : This function mitigates any picture movement due to external factors such as wind. * FONT COLOR : You can change the OSD font color. (White, Yellow, Green, Red, Blue) * SHARPNESS : As you increase this value, the picture outline becomes stronger and clearer. Adjust this value appropriately depending on the sharpness of the picture.
* RETURN : Select this to save the settings for the IMAGE ADJ menu and to return to the
SETUP menu.
Page 36
35
NOTE
When the V-REV or H-REV mode is enabled, the text on the screen does not ip.
If you increase the SHARPNESS level too high, the picture may become distorted or noise
may appear.
NOTE
When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if
you enter one.
Only English is available in this mode.
If you move the cursor to CLR and press the Function Setup switch, all the letters are deleted. To edit a letter, change the cursor to the bottom left arrow and press the Function Setup switch. Move the cursor over the letter to be edited, move the cursor to the letter to be inserted and then press the Function Setup switch.
CAM TITLE : If you enter a title, the title will appear on the monitor.
1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates 'CAM TITLE'.
2) Set it to 'ON' by using the Function Setup switch.
3) Press the Function Setup switch.
4) Use the Function Setup switch to move to a desired letter and select the letter by pressing the Function Setup switch. Repeat this to enter multiple letters. You can enter up to 15 letters.
5) Enter a title, move the cursor to 'POS' and press the Function Setup switch. The entered title appears on the screen. Select the position to display the title on the screen by using the Function Setup switch and press the Function Setup switch. When the position is determined, select 'END' and press the Function Setup switch to return to the SPECIAL menu.
SYNC :
In areas where the supply is at 60Hz(NTSC), 50Hz(PAL), you can synchronize the output phase of multiple cameras using the power synchronization function (Line-Lock) without using a synchronization signal generator.
CAMERA TITLE SETUP
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-.0123456789
←→CLR POS END
SHOP
MONITOR : Please change the settings value of video appropriate to your monitor.
1) LCD : Please select this menu item when using a LCD monitor.
2) CRT : Please select this menu item when using a CRT monitor.
3) USER : Please use this menu item when using a monitor other than standard ones. You can change the gamma, PED level, and color gain in the sub menus.
Page 37
36
NOTE
When using AC power at 60Hz(NTSC), 50Hz(PAL), frequency, you can use the L/L type
synchronization.
When the power is DC 12V, the SYNC menu is xed to the ‘INT’ mode.
MOTION DET :This product has a feature that allows you to observe movement of objects in 8 different areas on the screen, and the words 'MOTION DETECTED' appear on the screen when movement is detected. Activity can be monitor more efficiently.
1) When the SPECIAL menu screen is displayed, press the Function Setup switch so that the arrow indicates‘MOTION DET’.
2) Set up the mode using the Function Setup switch.
- SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY number is high, motion detection sensitivity is increased to recognize even small movement.
- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.
- SEL POS : Determines which of the 4 vertices of each MD area is to be used.
- XPOS : Determines the coordinate of the horizontal axis for SEL POS.
- YPOS : Determines the coordinate of the vertical axis for SEL POS.
- FILLgSET : Fills in a selected MD area. The color of the area can be selected from brown, orange, blue, cyan, green, yellow, magenta and red.
- RETURN : Select this to save the MOTION DET menu settings and return to the SPECIAL menu.
PRIVACY : Mask an area you want to hide on the screen.
MOTION DET
PRIVACY AREA SETUP
1.SENSITIVITY
2.AREA MODE
3.SEL POS
4.XPOS
5.YPOS
6.FILL → SET
7.RETRUN
1.AREA
2.MODE
3.MASK COLOR
4.MASK TONE
5.TOP
6.BOTTOM
7.LEFT
8.RIGHT
9.RETURN
AREA1
ON
L-TOP
3 5
AREA1
OFF
GREEN
1 39 79 13 52
- INT : Internal Synchronization Type
- L/L : Power Synchronization Type, Line-lock * Press the Function Setup switch. * You can select a desired phase from 0 to 359 when select 'phase'.
Page 38
37
1) When the SPECIAL menu screen is displayed, press the Function Setup switch so that the arrow indicates 'PRIVACY'.
2) Set up the mode using the Function Setup switch.
- AREA : You can select up to 12 PRIVACY areas.
- MODE : Determines whether to use the area selected in the AREA.
- MASK COLOR : Determine area color. You can select Green, Red, Blue, Black, White, Gray.
- MASK TONE : Adjust the brightness of MASK COLOR.
- TOP/BOTTOM/LEFT/RIGHT :Adjust the size and position of the selected area.
- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu.
RETURN Setting
Select a desired RETURN mode using the Function Setup Switch.
- SAVE : Save the current settings and RETURN the MAIN SETUP menu.
- NOT SAVE : Do not save the current settings and RETURN the MAIN SETUP menu.
- RESET : Resets the camera settings to the factory defaults. Language, Communication and Monitor Settings are not initialized.
Page 39
38
Trouble Shooting
PROBLEM
Northing appears on
the screen.
F
Check the power cable, power supply output and video
connection between the camera and monitor.
F
Are the camera lens or the lens glass dirty?
Clean the lens / glass with a soft clean cloth.
F
Adjust the monitor controls, as required.
F
If the camera is facing a very strong light, change
the camera position.
F
Adjust the lens focus.
F
Adjust the contrast control of the monitor.
F
If there is an intermediate device, correctly set the 75Ω/Hi-z.
F
Has MOTION DET been set to ON in the menu?
F
Has MD AREA been properly dened?
F
Check that the AGC setting in the EXPOSURE menu is’t set to OFF.
F
Check the EXPOSURE menu and make sure SHUTTER is set to------.
F
Make sure that the camera isn’t facing direct sunlight or
uorescent lighting. If necessary,change the camera position.
F
Check the settings in WHITE BALANCE menu.
F
Check the camera is correctly connected to an appropriate
regulated power source.
The image on the
screen is dim.
The camera is not
working properly and the surface of the camera is hot.
The image on the
screen is dark.
Motion Detection
is not activated.
The color of the
picture is not correct.
The image on the
screen ickers.
The INTENSIFY does
not work.
POSSIBLE CAUSE
Page 40
39
Page 41
40
u
MEMO
Page 42
41
u
MEMO
Page 43
42
u
MEMO
Page 44
200 New Highway
Amityville, NY 11701
631-957-8700
1 800 645 5516
www.specotech.com
Loading...