Speco HLED31D7B, HLED31D1B, HLED31D1W, HLED31D7W User Manual

Ø100

SCREW TP1

3.5X20 2EA

◈NOTES:

1. Do not install the camera outdoors.

2. Choose a location for the camera which is free o moisture and vibration.

3. Be careful not to scratch the camera lens or dome cover.

4. Do not operate camera beyond listed temperature

(-49°F~122°F)

5. Handle with care. Dropping it can cause serious damage to the camera.

6. Avoid any direct sun light into the lens.

7. To avoid shorting or damaging the camera, use only power supplies which meet the listed specifications (12VDC / 24VAC Dual voltage, 1A)

◈FEATURE

1. 650 TVL High Resolution Image

2. Smart DNR technology; reduces noise in low light.

3. 75’ range visible in total darkness with 24pcs of IR LEDs. (Indoor).

4. This camera is flexible to install with its 3-axis camera construction, this allows for the camera to be mounted to ceiling, wall or slope surfaces.

5. True Day/Night, camera changes function based on illumination, IR illuminators in dark (option)

6. 8 individual privacy zones

7. DWDR (Digital Wide Dynamic Range)

8. Multi function: High Light Mask, Lens Shading Compensation, Smart Motion Detection

9. Smart IR: Objects can be clearly identified due to the function that decreases screen saturation o objects within a short distance when the IR s are active.

10. Multi-language OSD.

11. 12VDC / 24VAC Dual Voltage operation.

◈HOW TO INSTALL

1. Openi ng the dome

Push in the latch button and pull back dome. (Remove the protection sheet after installation is completed).

Protection sheet

LATCH BUTTON

2. Removing the dome

Lift the dome. W hen you push the latch button, it is unlocked and you can lift the dome.

3. Camer a instal lati on

a. Mount the camera set with the supplied screws on

ceiling or wall.

It is recommended to utilize the supplied screws.

SCREW TP1

3.5X20 2EA

HLED31D1B, HLED31D1W HLED31D7B, HLED31D7W

SCREW TP1

3.5X20 2EA

b. Please refer to Section 4 for details on Camera angl

adjustments c. Lens adjustment (Vari-focal Lens only) After opening the LED cover,

d. Re-assemble the camera.

4. Camer a angle adjustment

a. Pan adjustment: Turn the disk of camera and the

adjust direction to the right or left (-180˚ to 180˚) b. Tilt adjustment: Turn the camera holder (shown

below) to adjust the direction up or down (6˚ to

90˚) c. Rol l adjus tment : Rotate the camera holder (-178˚

to 178˚) <Caution > If the camera is adjusted beyond the angle limit, it may cause damage to the camera.

◈ASSEMBLY

LED COVER ASS’Y

HARNESS

SCREW

① By turning the “Tele-

Wide” knob, you ca access a range of foca lengths within specifie limits.

②Once the focal length i

determined, turn the “Near-Far” knob to se the focus for the desire scene.

LED COVER

DISK

CAMERA HOLDER

DOME COVER ASS’Y

CAMERA MODULE ASS’Y

SCREW

CONTROL PCB ASS’Y

PUSH BUTTON

DISK

BASE

ROTATION

CABLE

◈DIMENSION

101

48.1

Ø130.8

SPECIFICATION

◈

Model No.

Ima ge Se nsor 1/3" COLOR SONY SUPE R HAD CCD II

Effective P ixe l 768(H) x 494(V) Pixel

Cell Siz e

Scan ning S yst em 2 : 1 Interl ace

Sy nc. Type Inter nal

Resolution 650 TV -L ine

S/N 52dB or More (AG C O F F)

Vi deo Output 1.0 V p-p(S ync. Ne gativ e) Termina tion 75Ω

Mi n. Illumination

Ga mma γ = 0.45 typ.(0.2 ~ 1.0)

OS D Yes(M ulti Language)

W hite B alance ATW (2,50 0°K ~ 9,500°K )/MA NU AL /AWC

Sh utter S peed 1/60 ~ 1/100,000 sec

Se nse up Auto(Selectable l imit 2X~1024X)/FIXED/OFF

Backli ght OF F/BLC /HLC/D WD R

AG C LO W/MI DD LE /HIG H/OF F

DN R (3D) AU TO /LOW /MID D LE /HIGH /OFF

Motion D etecti on ON /OFF (4 Zone)

Privacy Zone ON /OF F(8 Zone)

Mir ror ON /OFF

Day & Ni ght AU TO , CO LO R, B/W

LE D Bri ghtness 24pcs, Smart IR Blemish

Com pensa tion

Len s f = 3.6mm f = 2.8 ~ 12m m

Power S upply 12V DC / 24VA C D ual V oltage

Cur rent C onsu mption M ax. 600mA (at 12V DC / 24VA C)

Oper ation Tem p. -49°F~122°F

Dime nsion Ø130.8(W) x 96(H ) mm

Wei ght 14.5 oz

※The specification is subject to change without any prior

notice to improve the quality.

HLE D 31D 7B HLE D 31D 7W

6.35

㎛

(H) x 7.4㎛(V )

0.01L ux(F /1.2) 0Lux (75’ Range with 24pcs LED) - Indoor

AU TO /OFF

◈FUNCTION SETTING

1. How to use the jog lever

①SET : Used to access the menu and confirm

selection.

②

UP, ③ DOWN : Used to move the cursor to up or down.

④LE FT, ⑤R IGHT : Used to move the cursor to left

or right and change the value.

⑥

EXT-VIDEO : Additional video output terminal for test monitor during installation.

⑦DEBUG PORT : It is used for upgrading the product

function and after-sales services.

Ø109

HLE D 31D 1B HLE D 31D 1W

3B25276A

. OSD Menu Structure

HLED31D1B, HLED31D1W HLED31D7B, HLED31D7W

OSD Menu Select Menu Sub Menu Summary

1. EXPOSURE

BRIGHTNESS 0~99 : Adjust brightness with a manual iris lens

MANUAL

LENS

AGC OFF, LOW, MIDDLE, HIGH

SENSE-UP

BACKLIGHT

3D-DNR OFF, LOW, MID, HIGH, AUTO

RETURN Move back to previous menu

2. WHITE BALANCE

AWB MODE

R-Y GAIN 0~255 Adjust Red tone of the image

B-Y GAIN 0~255 Adjust Blue tone of the image

RETURN Move back to previous menu

3. DAY&NIGHT

D&N MODE

BURST ON, OFF Transmit the burst signal or not in B/W mode

C_SUP 0~100 Color suppress controllable

A_SUP 0~100 Iris suppress controllable

SMART IR ON, OFF

RETURN Move back to previous menu

AUTO, OFF, X2, X4, X8, X16, X32, X64,X128, X256, X512, X1024

BLC

HLC

D-WDR SET LEVEL 0~20 : DWDR level adjust

ATW

MANUAL

PUSH

AUTO

AUTO-CDS

COLOR Fixed at color

B&W Fixed at B/W

EXT

E. SHUTTER

BRIGHTNESS 0~99 : Adjust brightness with a DC iris lens

E. SHUTTER

BLC LEVEL

TOP 0~15 : Adjust top position of BLC zone

BOTTOM 1~16 : Adjust bottom position of BLC zone

LEFT 0~15 : Adjust left position of BLC zone

RIGHT 1~16 : Adjust right position of BLC zone

HBLC

MODE

HLC LEVEL 1~100 : Level adjust

MASK 1~4

M-WR

M-WB

RETURN Move back to previous menu

DAY→NIGHT

NIGHT→DAY

DELAY TIME 0~15 : Select the duration time

RETURN Move back to previous menu

A.DAY→NIGHT

A.NIGHT→DAY

C.DAY→NIGHT

C.NIGHT→DAY

DELAY TIME 0~15 : Select the duration time

RETURN Move back to previous menu

DELAY TIME

RETURN Move back to previous menu

AUTO, 1/60, 1/100FLK, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000, 1/100000 : Adjust shutter speed

AUTO, 1/60, 1/100FLK, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000, 1/100000 : Adjust shutter speed Determines that use the AGC function or not and AGC level selectable(You can not use the Auto D&N change mode when AGC is off)

Using sense up when it is low luminance (x2~x1024)

OFF, LOW, MID, HIGH : Use BLC function or not / level selectable

OFF : Deactivates HBLC function

MANUAL

HBLC LEVEL : OFF, LOW, MID, HIGH

TOP : 0~15

BOTTOM : 1~16

LEFT : 0~15

RIGHT : 1~16 ALL DAY : Activates HBLC function all day

NIGHT : Use the function at night only

TOP : 0~33

BOTTOM : 1~34

LEFT : 0~44

RIGHT : 1~45

OFF : HLC MASK OFF

Reduce noise in low illumination (Level selectable)

Color temperature 2500~9500°K

0~128 : Adjust the Red value to shift the color of the object 0~128 : Adjust the Blue value to shift the color of the object

Find the optimal white balance for current luminance environment

7~30

Select brightness of illumination about changing the day↔night mode by AGC

6~29

6~36

Select brightness of illumination about changing the day↔night mode by AGC

6~36

0~255

Select brightness of illumination about changing the day↔night mode by CDS

0~255

0~15 : Change the color↔B/W by external signal(N/A)

Decreases screen saturation of objects within a short range

Make a zone for HBLC

Make a zone for HLC mask

OSD Menu Select Menu Sub Menu Summary

4. IMAGE ADJUST

MIRROR MIRROR, OFF Set a vertical image inversion

SHARPNESS 0~30 Sharpness adjustable

0.45, 0.55, 0.65 Set a gamma value

GAMMA

LSC

RETURN Move back to previous menu

5. MOTION

MOTION ON, OFF Motion detection function activate/deactivate

AREA

SENSITIVITY 1~30 Motion detection sensitivity

DISPLAY OFF, MESSAGE, TRACE Select notification method of motion detection

HOLD TIME 0~15 Set the duration of alarm out

ALARM OUTPUT

RETURN Move back to previous menu

6. PRIVACY

MASK 1~8

RETURN Move back to previous menu

7. SPECIAL

LANGUAGE ENGLISH, … : Select language(9 languages)

TITLE OFF--ON

COMMUNICATION (N/A)

DPC

FACTORY SET

RETURN

8. EXIT

SAVE AND EXIT

EXIT Escape the menu without save

RETURN Move back to previous menu

USER

OFF LSC OFF

AREA 1~4

RETURN Move back to previous menu

ON, OFF Alarm ON/OFF

OFF Display each privacy mask or not

OFF--ON

OFF

AUTO

YES, NO Reset your cam era to factory default condition

Save the value and exit menu

GAMMA

RETURN Move back to previous menu

SET LEVEL 0~30 : Use the LSC and level adjustable

RETURN Move back to previous menu

TOP 0~143

BOTTOM 2~145

LEFT 0~190

RIGHT 2~192

RETURN Move back to previous menu

DOT SEL

DOT XY ENTER SETTING : Determines the coordinate

MOVE XY ENTER SETTING : Move the mask

COLOR BLACK, WHITE, … : Select mask color(8 colors)

RETURN Move back to previous menu

EDIT Display the camera name on the screen

RESET Camera name reset

POSITION Camera name position

RETURN Move back to previous menu

BAUDRATE 2400, 4800, 9600 : Select baud rate

PROTOCOL P ELCO-D : Camera protocol

RETURN Move back to previous menu

WHITE THR

LUMA THR

RETURN Move back to previous menu

0.20, 0.25, 0.30, 0.35, 0.40, 0.45, 0.50, 0.55,

0.60, 0.65, 0.70, 0.75, 0.80, 0.85, 0.90, 0.95,

1.00 : Gamma adjustable

Make a zone for motion detection

L_TOP, L_BOT, R_BOT, R_TOP : Determines which of the 4 vertices of each MD

area is to be used

1~255 : Select the camera ID for RS-485 communication

Deactivates Defect Pixel Correction in low illumination 0~255 : Setup the l imited value of white pixel correction 0~255 : Setup the l imited value of white pixel correction

Return to previous menu (Communication setting is not changed)

Speco Technol ogies is constantly developing product improvements. We reserve the right to modify product design and specifications without notice and without incurring any obligation.

Rev. 08/17/12.

3B25276B