Speco HiD8 Installation Guide

The lighting flash with an arrowhead symbol, within an equilateral triangle
is intended to alert the user to the presence of non-insulated dangerous
voltage within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the appliance.

This installation should be made by a qualified service person and should conform to

all local codes.

CAUTION

TO REDUCE THE RISK OF ELECTRLC SHOCK,

DO NOT REMOVE THE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED PERSONNEL.

RISK OF ELECTRLC

SHOCK

DO NOT OPEN

CAUTION

HiD8

Camera x 1

Manual x 1

Extra Video

output x 1

Tapping screws x 3

Plastic anchor x 3

Drilling template x 1

Torx Wrench x 1

BNC Female for TVI

Ceiling Tile

Drilling template

Plastic Anchor (3EA)

Tapping Screw

Ø 4 x 1.18in (3EA)

Dome Cover

Ass'y

Torx Screw

Ø 3 x 0.59 (3EA)

Torx L-Wrench

Safety Wire

Camera Ass'y

DC Power Jack

The front side of the
camera

Tilt lever

Tilt 90˚

Rotate

180˚

Pan 360˚

Pan base

Top Rubber x 1

Junction Box x 1

Sponge x1

Screw PH

(M4 x 0.47in) x 3

Tapping Screws

(Ø 4 x 1.18in) x 4

Plastic Anchor x 4

Chameleon

Cover x 1

HD-TVI 2MP Ultra Intensifier® Vandal Dome Camera

QUICK INSTALLATION GUIDE

 Special features

 Sony 1/2.8" 2.1MP STARVIS CMOS Sensor
 Supports image resolution up to 1920 x 1080P @ 30fps
 Max. Transmission distance: 985ft over Coaxial cable
 Ultra low light performance
 F = 0.95, 3.6mm 2Megapixel Fixed Lens
 TVI / CVBS (EXT) Output
 Supports WDR, Defog, 2D / 3D DNR, Slow Shutter control (Sense-Up)
 Privacy Masking up to 16 areas
 Full OSD operation through on board control and UTC (up the coax)
 Dynamic Motion Detection (4separable areas)
 Supports 5 Languages
 Perfect 3-Axis Mechanism
 12VDC operation
 IP67 compliant

DEAR CUSTOMERS!

By selecting this product, you have decided to use a professional device that
guarantees highest quality and reliability. We would like to thank you very much for
your confidence and kindly ask you to read the following instructions carefully before
installation and operation in order to take full advantage of all quality features
regarding this product.

INFORMATION

This equipment has been tested and found to comply with limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.

WARNING

Changes or modifications not expressly approved by the manufacturer could void
the user’s authority to operate the equipment.

CAUTION – To prevent electric shock and risk of the fire hazards

 Do NOT use power source other than that specified.
 Do NOT expose this appliance to rain or moisture.

1. Precautions

 Please read the manual carefully before the installation in order to make use the

camera to be set up correctly and to have the best picture quality.

 Please keep the manual in good condition for your future reference and service

application.

 Installation and services should only be carried out by an authorized personnel

according to local safety regulations.

 If any liquid or solid matter gets into the housing, immediately disconnect the camera

from power supply and have it checked by your authorized dealer before reusing.

 Avoid installing the camera at extremely hot or cold places.
 If you are not a certified person, never try to dismantle the camera.

To avoid electric shock, never remove the screws or covers. There are no parts inside
that need maintenance by the user. All maintenance should be carried out by qualified
personnel.

 Avoid installing the camera at a place of high humidity.
 Avoid installing the camera at the place exposed to gas or oil.
 Keep the top glass of the lens always clean in order to obtain the best picture quality

all the time. Be careful not to be stained by fingerprint.

 Don't face the camera directly toward sunlight or sunlight reflecting area.

CMOS may go defective at this condition.

 Please give a special attention to keep the unit from dangerous drop or external shock

during the process of transportation or handling.

 Never try to touch the camera in wet hand. It may cause an electric shock.
 Do not expose the camera to radioactivity. It causes a serious damage on the CMOS.

2. Limitation of liability

This publication is provided “AS IS” without warranty of any kind, either express or
implied, including but not limited to, the implied warranties of merchantability, fitness for
any particular purpose, or non-infringement of the third party's right.
This publication could include technical inaccuracies or typographical errors.
Changes are added to the information herein, at any time, for the improvements of this
publication and / or the corresponding product(s).

3. Disclaimer of warranty

In no event shall seller be liable to any party or any person, except for replacement or
reasonable maintenance of the product, for the cases, including but not limited to below :

(1) Any damage and loss, including without limitation, direct or indirect, special,

consequential or exemplary, arising out of or relating to the product.

(2) Personal injury or any damage caused by inappropriate use or negligent operation of

the user.
(3) Unauthorized disassemble, repair or modification of the product by the user.
(4) Inconvenience or any loss arising when images are not displayed, due to any reason

or cause including any failure or problem of the product.
(5) Any problem, consequential inconvenience, or loss or damage, arising out of the

system combined by the devices of third party.
(6) Any claim or action for damages, brought by any person or organization being

photogenic subject, due to violation of privacy with the result of that surveillance-

camera's picture, including saved data, for some reason, becomes public or is used

for the purpose other than surveillance.

4. Package

- Junction Box

5. Installation

5-1. Adjust Pan, tilt and Rotation and the View Angle

- Pan, Tilt, Rotate (3-Axis mechanism) makes easy to monitor the desired view。

 Panning axis can be adjusted 360°
 Tilting axis can be adjusted 0° ~ 90°
 Rotating axis can be adjusted

between +180° (clockwise)
and -180° (counter-clockwise)
Do not rotate more 180° as this
might cause the internal cables to
twist and disconnect or break.

- How to adjust the View Angle

a. Panning 360 degree

Turn the pan base right or left to adjust the pan angle.

b. Tilting 90 degree

Loosen the tilt lever on the right or left side of the camera board.
Control the camera tilt angle and fasten the tilt lever again.

c. Rotation 180 degree

Grasp the front side of the camera board and turn it right or left to set the exact
angle of image.

5-2. How to install on the Ceiling

① Paste a Drilling Template on the ceiling. (or wall)
② Drill screw points which will be done for installation.

Fix the plastic anchors in the holes. (in case of masonry ceiling or wall)

③ Mount the camera set by using Tapping Screws with Ø 4 provided.
④ Set the position and angle of the cameras to a desired direction and assemble the dome

cover.

5. Installation

PRESET MENU

INDOOR / OUTDOOR / LOW LIGHT / HALLWAY / LOBBY / ELEVATOR

SETUP

LENS

DC

MANUAL

EXPOSURE

BRIGHTNESS

SHUTTER

INTENSIFY

AGC

RETURN

WHITE BAL

AUTO

AWB

AWC-SET

MANUAL

BACKLIGHT

WDR

BLC

HLC

OFF

DAY&NIGHT

COLOR

B/W

AUTO

DNR

LOW

MIDDLE

HIGH RETURN

IMAGE

SHARPNESS
ACE

GAMMA
DEFOG

COLOR
GAIN
RETURN

MIRROR

FLIP

MOTION

ON

OFF

SYSTEM

ANALOG HD
COLOR BAR
RESET

FRAME RATE
LANGUAGE

FREQ
CAM TITLE

IMAGE RANGE
CAM TITLE

COLOR SPACE
RETURN

EXIT

Problems

Troubleshooting

Nothing appears on
the screen.

 Please check that the power cord and line connection

between the camera and monitor are fixed properly.

 Please check that you have properly connected Video cable to

the camera Video output jack.

The dim image
on the screen.

 Is lens stained with dirt? Clean your lens with soft, clean cloth.
 Set the monitor to proper condition.
 If the camera is exposed to too strong light, change the

camera position.

 Please check if the power supply is within the specification &

cables.(Due to the voltage drop with distance and gauges,
Led will light poor)

The dark image
on the screen.

 Adjust the contrast feature of the monitor.
 If there is an intermediate device, set the 75Ω / Hi-Z properly.

(Please check the impedance)

The camera is not
working properly,
and the body of the
camera is hot.

 Please check if the power supply is regulated and is within the

standard requirement of the products.

Color is not correct.

 Please check the setting of White Balance setup.

The screen is
flickering.

 Please check if the camera is facing directly towards sunlight

or fluorescent light.

MODEL

HiD8

Image sensor

Sony 1/2.8 inch 2.1MP STARVIS CMOS Sensor

Total Pixel

1945(H) x 1109(V) 2.16 Megapixel

Effective Pixels

1945(H) x 1097(V) 2.13 Megapixel

Scanning system

Progressive scan

Video output

1920 x 1080 @ 25fps / 30fps, 1280 x 720 @ 25fps /
30fps

Output

TVI

S/N ratio

More than 520B (AGC OFF / Weight ON)

Min. Illumination

0.001Lux

Privacy Mask

ON / OFF (16 zone)

Motion

ON / OFF (4 zone)

NEG.Image

ON / OFF

Mirror / Flip

ON / OFF

White Balance

AUTO / AWB / AWB - SET / MANUAL

Shutter

AUTO / MANUAL / FLICKER

Sens-UP

AUTO / OFF (Selectable Limit x2 ~ x32)

Backlight

OFF / HLC / BLC / WDR

2D / 3DNR

OFF / LOW / MIDDLE / HIGH

AGC (Auto Gain Control)

0 ~ 10 (Level adjustable)

Day & Night

COLOR / B&W / AUTO

Sharpness

0 ~ 10 (Level adjustable)

WDR

NORMAL / ROI

Defog

ON / OFF

Language

ENG, CHN, CHN(S), JPN, KOR

Lens

F=0.95, 3.6mm 2Megafixel Fixed Lens

Power Source

12VDC

Operating current

100mA ±10% (12VDC)

Operating
Temperature

-40F ~ 140F

Storage
Temperature

-40F ~ 140F

Operating Humidity

0%RH ~ 90%RH

Measurement(in)

121.2(Ø ) x 3.79(H)

Weight(Approx. oz)

52oz

Coaxial
5C / 3C

TVI DVR

Monitor

Ceiling Tile

Plastic Anchor (4EA)

Junction Base Sponge

Junction Box Assembly
Tapping Screw Ø4 x 1.18in (4EA)

Bottom Ass'y

Safety Wire

PH M4 x 0.47in (3EA)

Top Case Ass'y

L-Wrench

190515_SPECO_TVI

Federal Communications Commission (FCC) Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired

operation.

FCC Responsible Party :

Speco Technologies
200 New Highway
Amityville, NY 11701

www.specotech.com

 Ceiling_Junction Box

① Attach the Sponge on junction Box.
② Mark the hole of junction box on the ceiling with tapping screw.
③ Drill the hole and input the anchor. And install the junction box with Tapping Screw.
④ Input Cable inside Junction Box.
⑤ Install Bottom Ass'y on junction box with PH M4 x 0.47in.
⑥ Install Top Case Ass'y on Bottom Ass'y with L-Wrench.

5-3. Application of TVI output

6. Function and operation

6-1. On Screen Display (On board control and UTC)

7. Troubleshooting

If there are problems in operating, please refer to the checklist below.
If the problem persists, please contact the agent where this product is purchased.

8. Dimension (in)

9. Specifications

 Specifications are subject to change without prior notice for better improvement.