How it Works
Speco
Loading...
HiB68
Installation Guide
2 pgs462.16 Kb0
Specsheet
1 pgs695.87 Kb0

Speco HiB68 Installation Guide

The lighting flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of non-insulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
This installation should be made by a qualified service person and should conform to
all local codes.
Camera x 1
Manual x 1
L-Wrench x 1
Tapping screws x 3
Plastic anchor x 3
CAUTION
TO REDUCE THE RISK OF ELECTRLC SHOCK,
DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
RISK OF ELECTRLC
SHOCK
DO NOT OPEN
CAUTION
L-Wrench
Tapping screw Ø 4 x 1.18in (3EA)
(A)
(B) Bracket nut
Plastic anchor (3EA)
HiB68
BNC Female for TVI
DC Power Jack
Top Rubber x 1
Top Rubber x 1
Top Adapter Plate x 1
Junction Box x 1
Sponge x 1
Tapping screw
(Ø 4 x1.18in) x 4
Plastic anchor x 4
Screw PH
(M4 x 0.3in ) x 3
Screw PH
(M4 x 047in ) x 4
Extra Video
output x 1
HD-TVI 2MP Ultra Intensifier® Bullet Camera
QUICK INSTALLATION GUIDE
Special features
DEAR CUSTOMERS!
By selecting this product, you have decided to use a professional device that guarantees highest quality and reliability. We would like to thank you very much for your confidence and kindly ask you to read the following instructions carefully before installation and operation in order to take full advantage of all quality features regarding this product.
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
CAUTION – To prevent electric shock and risk of the fire hazards
Do NOT use power source other than that specified. Do NOT expose this appliance to rain or moisture.
1. Precautions
Please read the manual carefully before the installation in order to make use the
camera to be set up correctly and to have the best picture quality.
Please keep the manual in good condition for your future reference and service
application.
Installation and services should only be carried out by an authorized personnel
according to local safety regulations.
If any liquid or solid matter gets into the housing, immediately disconnect the camera
from power supply and have it checked by your authorized dealer before reusing.
Avoid installing the camera at extremely hot or cold places. If you are not a certified person, never try to dismantle the camera.
To avoid electric shock, never remove the screws or covers. There are no parts inside that need maintenance by the user. All maintenance should be carried out by qualified personnel.
Avoid installing the camera at a place of high humidity. Avoid installing the camera at the place exposed to gas or oil. Keep the top glass of the lens always clean in order to obtain the best picture quality
all the time. Be careful not to be stained by fingerprint.
Don't face the camera directly toward sunlight or sunlight reflecting area.
CMOS may go defective at this condition.
Please give a special attention to keep the unit from dangerous drop or external shock
during the process of transportation or handling.
Never try to touch the camera in wet hand. It may cause an electric shock. Do not expose the camera to radioactivity. It causes a serious damage on the CMOS.
2. Limitation of liability
This publication is provided “AS IS” without warranty of any kind, either express or implied, including but not limited to, the implied warranties of merchantability, fitness for any particular purpose, or non-infringement of the third party's right. This publication could include technical inaccuracies or typographical errors. Changes are added to the information herein, at any time, for the improvements of this publication and / or the corresponding product(s).
3. Disclaimer of warranty
In no event shall seller be liable to any party or any person, except for replacement or reasonable maintenance of the product, for the cases, including but not limited to below :
(1) Any damage and loss, including without limitation, direct or indirect, special,
consequential or exemplary, arising out of or relating to the product.
(2) Personal injury or any damage caused by inappropriate use or negligent operation of
the user. (3) Unauthorized disassemble, repair or modification of the product by the user. (4) Inconvenience or any loss arising when images are not displayed, due to any reason
or cause including any failure or problem of the product. (5) Any problem, consequential inconvenience, or loss or damage, arising out of the
system combined by the devices of third party. (6) Any claim or action for damages, brought by any person or organization being
photogenic subject, due to violation of privacy with the result of that surveillance-
camera's picture, including saved data, for some reason, becomes public or is used
for the purpose other than surveillance.
4. Package
- Junction Adaptor
- Junction Box
5. Installation
5-1. How to install on the Ceiling / Wall
Ceiling
Wall
① Drill three screw holes on the wall plate to fix three plastic anchors (supplied) in the holes. ② Fix the plastic anchors in the holes. ③ Position the bracket on the screw points. ④ Fix the bracket by tightening the screws.
⑤ Slightly loosen bolt (A), Bracket nut (B), then adjust the direction of the camera and then
tighten bolt the Bracket nut.
Ceiling_Junction Box
PRESET MENU
INDOOR / OUTDOOR / LOW LIGHT / HALLWAY / LOBBY / ELEVATOR
SETUP
LENS
DC
MANUAL
EXPOSURE
BRIGHTNESS
SHUTTER
INTENSIFY
AGC
RETURN
WHITE BAL
AUTO
AWB
AWC-SET
MANUAL
BACKLIGHT
WDR
BLC
HLC
OFF
DAY&NIGHT
COLOR
B/W
AUTO
DNR
LOW
MIDDLE
HIGH RETURN
IMAGE
SHARPNESS ACE
GAMMA DEFOG
COLOR GAIN RETURN
MIRROR
FLIP
MOTION
ON
OFF
SYSTEM
ANALOG HD COLOR BAR RESET
FRAME RATE LANGUAGE RETURN
FREQ CAM TITLE
IMAGE RANGE CAM TITLE
COLOR SPACE RETURN
EXIT
Problems
Troubleshooting
Nothing appears on the screen.
Please check that the power cord and line connection
between the camera and monitor are fixed properly.
Please check that you have properly connected Video cable to
the camera Video output jack.
The dim image on the screen.
Is lens stained with dirt? Clean your lens with soft, clean cloth. Set the monitor to proper condition. If the camera is exposed to too strong light, change the
camera position.
Please check if the power supply is within the specification &
cables.(Due to the voltage drop with distance and gauges, Led will light poor)
The dark image on the screen.
Adjust the contrast feature of the monitor. If there is an intermediate device, set the 75Ω / Hi-Z properly.
(Please check the impedance)
The camera is not working properly, and the body of the camera is hot.
Please check if the power supply is regulated and is within the
standard requirement of the products.
Color is not correct.
Please check the setting of White Balance setup.
The screen is flickering.
Please check if the camera is facing directly towards sunlight
or fluorescent light.
MODEL
HiB68
Image sensor
Sony 1/2.8 inch 2.1MP STARVIS CMOS Sensor
Total Pixel
1945(H) x 1109(V) 2.16 Megapixel
Effective Pixels
1945(H) x 1097(V) 2.13 Megapixel
Scanning system
Progressive scan
Video output
1920 x 1080 @ 25fps / 30fps, 1280 x 720 @ 25fps / 30fps
Output
TVI
S/N ratio
More than 520B (AGC OFF / Weight ON)
Min. Illumination
0.001Lux
Privacy Mask
ON / OFF (16 zone)
Motion
ON / OFF (4 zone)
NEG.Image
ON / OFF
Mirror / Flip
ON / OFF
White Balance
AUTO / AWB / AWB - SET / MANUAL
Shutter
AUTO / MANUAL / FLICKER
Sens-UP
AUTO / OFF (Selectable Limit x2 ~ x32)
Backlight
OFF / HLC / BLC / WDR
2D / 3DNR
OFF / LOW / MIDDLE / HIGH
AGC (Auto Gain Control)
0 ~ 10 (Level adjustable)
Day & Night
COLOR / B&W / AUTO
Sharpness
0 ~ 10 (Level adjustable)
WDR
NORMAL / ROI
Defog
ON / OFF
Language
ENG, CHN, CHN(S), JPN, KOR
Lens
F = 0.95, 3.6mm 2Megafixel Fixed Lens
Power Source
12VDC
Operating current
200mA ±10% (12VDC)
Operating Temperature
-40F ~ 140F
Storage Temperature
-40F ~ 140F
Operating Humidity
0%RH ~ 90%RH
Measurement(in)
7.28 (W) x Ø 76 (H)
Weight(Approx. oz)
18oz
Coaxial 5C / 3C
Panning 360°
Tilt 90°
Rotation 360°
TVI DVR
Monitor
Bracket nut
Ceiling Tile
Plastic anchor (4EA)
Junction Base Sponge
Junction Box Assembly
Tapping screw Ø4 x 1.18in (4EA)
Top Adapter Plate
Top Rubber
Camera Ass'y
PH (M4 x 0.3in) (3EA)
Finish with Super X
PH (M4 x 0.47in) (4EA)
190515_SPECO_TVI
Federal Communications Commission (FCC) Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired
operation.
FCC Responsible Party :
Speco Technologies 200 New Highway Amityville, NY 11701
www.specotech.com
5-2. Tool-free 3-Axis mounting mechanism
Perfect 3-axis
Panning up to 360° Tilting up to 90° Rotation up to 360°
① Panning 360˚
Slightly loosen Pan Bracket nut then adjust pan of the camera and tighten the Bracket nut.
② Tilt 90˚
Slightly loosen Tilt bolt then adjust tilt of the camera and tighten the bolt firmly.
③ Rotation 360˚
Slightly loosen Tilt bolt then adjust rotation of the camera and tighten the bolt firmly.
5-3. Application of TVI output
6. Function and operation
6-1. On Screen Display (UTC Only)
7. Troubleshooting
If there are problems in operating, please refer to the checklist below. If the problem persists, please contact the agent where this product is purchased.
8. Dimension (in)
9. Specifications
Specifications are subject to change without prior notice for better improvement.
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use