Safety Instructions
p
IMPORTANT: PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLATION AND
RETAIN
Caution For Use
◈ Do not open the camera body.
◈ Do not insert object into the camera body.
◈ Do not touch with wet hands.
◈ Do not remove power cord while camera is in use.
◈ If signs of smoke or fire are detected, immediately remove main power.
Caution For Installation
◈ Camera requires 12 V DC adaptor for power and therefore must never be
connected
directly to mains power.
◈ Apply mains power after full installation of camera.
◈ Do not install camera facing directly into strong light.
◈ Do not install in areas of high humidity / heat or low temperature.
◈ Do not install in areas of high dust or particle pollution.
◈ Do not ex
ose the camera to rain or moisture.
1
Contents
◈ OSD CONTROL BUTTON TYPE ...................................................................................................... 3
◈ SET UP MENU .................................................................................................................................. 3
◈ MENU SET UP ................................................................................................................................. 4
◈ LENS ................................................................................................................................................. 5
◈ SHUTTER ........................................................................................................................................ 6
◈ BLC ................................................................................................................................................... 7
◈ AGC .................................................................................................................................................. 10
◈ WHITE BALANCE .......................................................................................................................... 11
◈ FUNCTION ..................................................................................................................................... 13
◈ CAMERA ID .................................................................................................................................... 14
◈ MIRROR ......................................................................................................................................... 15
◈ DAY & NIGHT ................................................................................................................................ 16
◈ MOTION ......................................................................................................................................... 17
◈ PRAVACY ...................................................................................................................................... 18
◈ GAMMA .......................................................................................................................................... 20
◈ LANGUAGE .................................................................................................................................. 20
◈ RESET .......................................................................................................................................... 20
◈ ADJUST ........................................................................................................................................ 21
◈ EXIT ............................................................................................................................................... 21
◈ TROUBLE SHOOT ........................................................................................................................ 22
2
OSD Control Button Type
How To Operate the Camera Menu
◈ Setup Menu
LENS
SHUTTER
BACKLIGHT(B L C)
A G C(Auto Gain
WHITE BAL.
FUNCTION
ADJUST
EXIT
SETUP
●MANUAL ●DC ●VIDEO
●FIXED ●MANUAL ●AUTO ●F L K
●ON ●OFF
●ON ●OFF
●A T W ●A W B ●FIXED ●
●RETURN ●CAMERA ID ●MIRROR
●DAY & NIGHT ●MOTION ●PRIVACY
●GAMMA ●LANGUAGE ●RESET
●ADJUST ●RETURN
3
◈ Menu Set Up
A
1. Press the set up button
2. Setup menu will be displayed on the monitor
SETUP
LENS DC
SHUTTER FIXED
B L C ON
A G C ON
WHITE BAL A T W
FUNCTION
ADJUST
EXIT
3. Move the indicator UP or DOWN to adjust the desired Feature.
Select the desired
Feature
4. The LEFT or RIGHT button scrolls through the settings within the highlighted
function.
5. When all desired settings are complete use the DOWN button to move to and
highlight EXIT then press SET on the controller, this takes you out of the menu
SETUP
LENS DC
SHUTTER FIXED
B L C ON
A G C ON
WHITE BAL A T W
FUNCTION
ADJUST
EXIT
djust using
the LEFT or
RIGHT button
4
◈ LENS(Option)
Controls the picture brightness
1. Move the indicator to LENS by pressing the UP or DOWN button to scroll
through the SET UP menu screen.
2. Select the desired LENS type by pressing the LEFT or RIGHT button.
SETUP
LENS DC
SHUTTER FIXED
B L C ON
A G C ON
WHITE BAL A T W
FUNCTION
ADJUST
EXIT
DC/VIDEO:DC Auto IRIS Lens
MANUAL
VIDEO
Lens
CAUTION
☞ When DC/VIDEO Lens selected' you must select "FIXED",
When you use Manual Lens, You must select "AUTO"
DC
3. With DC selected the brightness can be manually adjusted. Press the SET UP
button then use the LEFT and RIGHT button to increase or decrease the level.
LENS DC
BRIGHTNESS
0 ~ 255
RETURN
4. Move the indicator to RETURN to the previous menu after complete
the adjustment.
5
◈ SHUTTER SPEED
K
1. Move the indicator to SHUTTER by pressing the UP or DOWN button to scroll
through the SET UP menu screen.
2. Select the desired type by pressing the LEFT or RIGHT button.
SETUP
LENS DC
SHUTTER FIXED
B L C ON
A G C ON
WHITE BAL A T W
FUNCTION
ADJUST
EXIT
a). Fixed:Lens shutter speed will be fixed to 1/60 sec when DC lens selected.
b). Manual:For manual shutter speed control
c). Auto:For automatic shutter speed control when the lens must be set to
manual to enable this setting.
d). F L K:For use where image is being affected and causing the image to
flicker or show interference. Cause can be flourescent lighting,
radio waves etc.
SHUTTER
Fixed
Manual
Auto
F L
3.Press the SET UP button to return to previous menu after
complete the adjustment
6
◈ BACKLIGHT(B L C)
1. Move the indicator to BLC by pressing the UP or DOWN button to scroll through
the SET UP menu screen.
SETUP
LENS DC
SHUTTER FIXED
B L C ON
A G C ON
WHITE BAL A T W
FUNCTION
ADJUST
EXIT
2. Select the desired setting by pressing the LEFT or RIGHT button.
B L C
ON
OFF
3. Adjustment when B L C ON.
B L C SET UP
B L C AREA
B L C RATIO 0 ~ 63
RETURN
7
4. When BLC On, BLC off
BLC ON
BLC OFF
5. Selection of sensing area.
☞ How to set up sensing area
1) Select Sensing area by pressing "UP & DOWN" button
2) Press the " SET UP" button and above picture will be displayed on the screen.
3) Move the Yellow square to select sensing area and press the
"set up" button and move to other desired sectors. If yellow square
color changes to green color, this sector selected by sensing are.
4) Repeat this to by pressing " UP or DOWN, LEFT or RIGHT and SET UP button
to set up the desired sensing area.
Moving yellow square
to select sesing area
8
6. BLC area.
After setup the BLC sensing area, enter the setup button for a
second and below picture will appear on the screen.
All sensing area re-adjusted by pressing "UP or DOWN" button and
"SETUP" Button.
B L C AREA
ALL CLEAR
ALL SET
RETURN
EXIT
7. Increasing or decreasing BLC Ratio.
Increasing or decreasing BLC Ratio could be controlled from
00 to maximum 63.
B L C SET UP
B L C AREA
B L C RATIO 0 ~ 63
RETURN
9
◈ A G C(Auto Gain Control)
AGC helps increase the image brightness. The desired option is seclected
using the LEFT or RIGHT buttons.
SETUP
LENS DC
SHUTTER FIXED
B L C ON
A G C ON
WHITE BAL A T W
FUNCTION
ADJUST
EXIT
1. Move the indicator to AGC by using "UP or DOWN" button and Press the
RIGHT button to select AGC ON, OFF mode.
2. When AGC ON, press the setup button and below AGC GAIN control will be
displayed on the screen. And press the LEFT or RIGHT button to increase
or decrease AGC GAIN
A G C CONTROL
A G C GAIN 0 ~ 255
EXIT
Desired A G C GAIN could be controlled from 0 to MAX 255 by
using LEFT or RIGHT button.
10
◈ WHITE BALANCE
SET "WHITE BAL." to desired mode by the RIGHT button
SETUP
LENS DC
SHUTTER FIXED
B L C ON
A G C ON
WHITE BAL A T W
FUNCTION
ADJUST
EXIT
① ATW(Auto Tracking White Balance)
:When color temperature is 1,800°K ~ 15,000°K, select this mode.
(Ex: A fluorescent lamp, or outdoors)
② AWB(Auto White Balance)
:The white balance is automatically adjusted in a specific environment.
In order to obtain the best result, press the set button while the camera
focuses on the white paper. If the environment including the light source
is changed, you have to adjust the white balance again.
③ FIXED(Auto White Balance Fixed)
:Auto white balance is fixed and adjusted by 4 steps.
④ MANUAL:To fine adjust, select the manual mode.
11
2. Set the "MANUAL" mode and press the "SETUP" button.
The red or blue factor could be increased while monitoring the
difference on the screen.
WHITE BAL. ATW
AWB
FIXED
MANUAL
A W B MANUAL
RED 0 ~ 255
BLUE 0 ~ 255
RETURN
Increased or decrease the value for RED(R-Gain) and BLUE(B-Gain) by press
the LEFT or RIGHT button. After set up the desired value, move to return menu
by pressing the DOWN button and press the SETUP button to previous menu.
☞ CAUTION
Proper White Balance may not be obtained under the following conditions.
In these case, select the AWB mode.
- When the scene contains mostly high color temperature object, such as
blue sky or sunset.
- When the scene is dim.
- If the camera faces a fluorescent lamp directly or is in an area with
constantly changing illumination
12
◈ FUNCTION
Set the "FUNCTION" mode and press the "SETUP" button.
The camera ID, Mirror, day & night and other necessary functions could
be controlled by user's requirement.
SETUP
LENS DC
SHUTTER FIXED
B L C ON
A G C ON
WHITE BAL A T W
FUNCTION
ADJUST
EXIT
FUNCTION
RETURN
CAMERA ID ON
MIRROR OFF
DAY & NIGHT AUTO
MOTION ON
PRIVACY ON
GAMMA 0.45
LANGUAGE
RESET
☞ CAUTION
- If the CAMERA TITLE feature is set to "OFF", the camera title will not be
displayed on the monitor
13
1. CAMERA TITLE
① Place the cursor under the Character "C" by pressing the LEFT or RIGHT
button and press the SETUP button to create the Camera title.
② Press the RIGHT button to place the cursor to the first place of chracter.
ID SETUP
CAMERA ID
CURSOR
C
POSITION
RETURN
③ Press the UP or DOWN button to select the required number or alphabet.
And move the cursor for next charater by pressing the RIGHT button.
( Character begins from number "0 ~ 9" and follows from" A ~ Z" )
④ After complete the CAMERA ID, select the "POSITION" at which camera
title should be located.
⑤ Press the "RETURN" button to exite after complete the set up.
2. MIRROR
① Press the RIGHT button to select the desired mode
FUNCTION
RETURN
CAMERA ID ON
MIRROR OFF
DAY & NIGHT AUTO
MOTION ON
PRIVACY ON
GAMMA 0.45
LANGUAGE
RESET
14
2.MIRROR
☞ OFF : Deactivation
☞ ON: Reverse the image RIGHT or LEFT such as mirror
MIRROR ON MIRROR OFF
3. DAY & NIGHT
① Press the RIGHT button to set up the desired mode.
FUNCTION
RETURN
CAMERA ID ON
MIRROR ON
DAY & NIGHT AUTO
MOTION ON
PRIVACY ON
GAMMA 0.45
LANGUAGE
RESET
☞ COLOR: The camera will always display a color picture
☞ B/W : The camera will always display a B/W picture
☞ AUTO: The camera will switch into B/W in the low light conditions.
15
② Press the UP or DOWN button to select desired mode.
③ Press the LEFT or RIGHT button to set up the desired value.
DAY NIGHT AUTO
DELAY 0 ~ 63
START LEVEL 0 ~ 255
END LEVEL 0 ~ 255
RETURN
4. MOTION
Whenever the camera detects motion, the " Running man " Signal will be appeared
on the right - up part of the screen.
FUNCTION
RETURN
CAMERA ID ON
MIRROR ON
DAY & NIGHT AUTO
MOTION ON
PRIVACY ON
GAMMA 0.45
LANGUAGE
RESET
☞ CAUTION
- Press the RIGHT button to activate the MOTION or deactivate
16
① Press the SETUP button to display the control menu on the screen.
ADJUSTMENT WHEN MOTION "ON"
MOTION
AREA
MOTION TH. 0 ~ 255
MOTION TRACE OFF
RETURN
② Press the SETUP button to select the motion area on the screen.
And Motion Sensing Area SETUP menu will be displayed on the sub menu screen.
☞ How to set up motion sensing area
1) Select motion area by pressing "UP & DOWN" button
2) Press the " SET UP" button and above picture will be displayed on the screen.
3) Move the Yellow square to select sensing area and press the
"set up" button and move to other desired sectors. If yellow square
color changes to green color, this sector selected by sensing are.
4) Repeat this to by pressing " UP or DOWN, LEFT or RIGHT and SET UP button
to set up the desired sensing area.
17
After setup the Motion sensing area, enter the setup button for a second
and below picture will appear on the screen.
MOTION AREA
ALL CLEAR
ALL SET
RETURN
EXITE
After complete the desired sensing area, press the RETURN or EXIT to move
previous menu or exit to main menu .
5. PRIVACY
To make an area that desired area to be private.
① Press the RIGHT button to activate or deactivate the PRIVACY mode.
FUNCTION
RETURN
CAMERA ID ON
MIRROR ON
DAY & NIGHT AUTO
MOTION ON
PRIVACY ON
GAMMA 0.45
LANGUAGE
RESET
ON:Activated
OFF:Deactivated
18
5. PRIVACY
② Press the SETUP button when the privacy mode "ON".
③ Set the"PRIVACY" to desired mode by the LEFT or RIGHT button.
PRIVACY AREA
AREA SEL AREA 0
AREA STATE
LEFT 0 ~ 255
RIGHT 0 ~ 255
TOP 0 ~ 255
BOTTOM 0 ~ 255
COLOR 0 ~ 15
RETURN
☞ How to set up desired area value
1) Desired area could be selected upto 0 ~ 3 steps by pressing RIGHT button.
2) Area state could be selected "ON" or "OFF" mode.
3) Area setup value could be changed by pressing UP or DOWN & LEFT or RIGHT
button.
4) Privacy area color could be changed upto 15 color.
19
6. GAMMA
Gamma value could be controlled by pressing the LEFT or RIGHT button.
FUNCTION
RETURN
CAMERA ID ON
MIRROR ON
DAY & NIGHT AUTO
MOTION ON
PRIVACY ON
GAMMA 0.45
LANGUAGE
RESET
User's control (0.00 ~ 1.00)
7. LANGUAGE
English
8. RESET
Set the menu to RESET by pressing SETUP button and appears YES /NO on
the screen.
If "YES" is selected, all data will be changed to factroy default.
20
◈ ADJUST
Set the ADJUST and press the setup button to control the desired contrast
and sharpness on the screen.
SETUP
LENS DC
SHUTTER FIXED
B L C ON
A G C ON
WHITE BAL A T W
FUNCTION
ADJUST
EXIT
① Press the LEFT or RIGHT button to increase or decrease the desired features.
ADJUST
COTRAST 0 ~ 255
SHARPNESS 0 ~ 255
CB - GAIN 0 ~ 255
CR - GAIN 0 ~ 255
RETURN
② Move to return and press the setup button to exit after complete desired
mode.
◈ EXIT
Set the EXIT and press the setup button to exit.
21
TROUBLE SHOOTING
PROBLEM SOLUTION
●Check the power cable and line connection
Nothing appears on
the screen.
The image on the
Screen is dim.
between the camera and monitor.
● Check that you have properly connected the
video cables.
●Is the camera lens stained with dirt?
Clean the lens with a soft and clean cloth.
● Adjust the monitor as required.
● If the camera is exposed to very strong light,
change the camera position.
● Adjust the lens focus properly.
The image on the
Screen is dark.
The camera is not working
properly and the surface of
the camera is hot.
MOTION DETECTION
function is not active.
The color of the picture
is not matched.
The image on the
Screen flickers.
● Adjust the contrast feature of the monitor.
● If you have an interediate device, set the 75Ω / Hi - z properly.
● Check that you have properly connected the camera
to an appropriate power source.
● Have you set " MOTION DET" menu to off?
● Have you set " MD AREA" properly?
● Check that you have properly set the " WHITE BAL." menu.
● Is the camera facing direct sunlight or fluorescent lighting?
Change the camera position.
22
INSTALLATION AND USER GUIDE
OF
OSD COLOR CAMERA
MADE IN KOREA
Loading...