Page 1
Insert Fittings Technical
Barbed Insert Fittings Weights & Dimensions
Dimensions of Insert Ends
ASTM D 2609
Nominal
Size in.
1/2 1-1/4 .665 .635 .015 .406
3/4 1-1/4 .865 .835 .015 .562
1-1/4 1-1/4 1.425 1.395 .025 .995
1-1/2 1-1/2 1.665 1.630 .030 1.125
2-1/2 2 2.520 2.487 .030 2.062
Insert Length
"P" min.
1 1-1/4 1.095 1.065 .020 .750
2 1-1/2 2.125 2.085 .030 1.656
3 2-1/8 3.125 3.086 .030 2.600
4 3 4.090 4.044 .030 3.525
Barb O.D. "Z"
max. min.
Barb Depth
"V" min.
Diameter "D"
Inside
min.
Dimensions of Polyethylene Pipe
ASTM D 2104 and D 2239
Nominal Size in. Average I.D. in. Tolerance in.
1/2 .622 +.010 - .010
3/4 .824 +.010 - .015
1 1.049 +.010 - .020
1-1/4 1.380 +.010 - .020
1-1/2 1.610 +.015 - .020
2 2.067 +.015 - .020
2-1/2 2.469 +.015 - .025
3 3.068 +.015 - .030
4 4.026 +.015 - .035
Insert Fittings Dimensions
G = (LAYING LENGTH) Intersection of center lines to insert bottom or thread bottom; 90° elbows, tees & crosses; ± 1/32 inch.
H = Intersection of center lines to end of insert or face of fitting; 90° elbows, tees & crosses; ± 1/32 inch.
L = Overall length of fittings; ± 1/16 inch.
N = (LAYING LENGTH) Insert bottom to insert bottom or thread bottom; couplings & straight adapters; ± 1/16 inch.
Dimensions of Spiral
Barb Ends
• ASTM D 2609
Plastic Insert Fittings for
Polyethylene (PE) Plastic Pipe.
It is the users responsibility to determine the suitability for the intended service application.
Page 11
STANDARDS & SPECIFICATIONS
• Material
®
Insert Fittings are produced from PVC
Spears
National Sanitation Foundation (NSF
Standard 14 Plastic Fittings for
Potable Water.
Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas
See Spears® Product Sourcebook for product offerings
)
®
Type 1, Minimum Cell Classification 12454.
CPVC Minimum Cell Classification 23447.
Spears® Manufacturing Company
Page 2
Insert Fittings Technical
Barbed Insert Fittings Weights & Dimensions
90° Ell - PVC
Insert x Mipt
Dimensions Also Applicable to
1413-XXXC CPVC Inserts
Part Number Size G G1 H H1
1413-010 1 11/16 23/32 2- 3/16 1-19/32 .07
1413-012 1-1/4 27/32 31/32 2-11/32 1-27/32 .11
1413-015 1-1/2 15/16 1- 3/32 2-23/32 2- 1/8 .17
1413-020 2 1- 1/4 1- 3/8 3 2- 7/16 .24
90° Ell Reducing - PVC
Insert x Mipt
(Continued)
Approx. Wt.
(Lbs.)
Part Number Size G G1 H H1
1413-055 3/8X3/4 7/16 3/4 1- 1/4 1- 1/2 .02
1413-101 3/4X1/2 1/2 1/2 2- 1/16 1- 7/32 .03
1413-130 1X1/2 23/32 3/4 2- 3/16 1-11/32 .05
1413-131 1X3/4 11/16 23/32 2- 5/32 1-13/32 .06
90° Side Outlet Ell - PVC
Insert x Insert x Fipt
Part Number Size G G1 H H1 M1
1414-101 3/4X3/4X1/2 5/8 13/32 2- 1/8 1- 1/8 1- 3/32 .06
1414-130 1X1X1/2 11/16 9/16 2- 3/16 1- 1/4 1- 5/16 .09
1414-131 1X3/4 15/16 15/32 2- 9/32 1- 3/16 1- 5/16 .10
Approx. Wt.
(Lbs.)
Approx. Wt.
(Lbs.)
Page 21
Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas
See Spears® Product Sourcebook for product offerings
Spears® Manufacturing Company
Loading...