Page 1
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,IRE-4.0 • LINEAR P/N: 223110B • INK: BLACK •
MATERIAL: 20LB. GLOSS WHITE PAPER • SIZE: 4.250” X 14.000” FOLD TO 4.250” X 3.500”
• FOLDING: 4 PARALLEL FAN-FOLDS, FINISH WITH LOGO SHOWING • SCALE: 1-1
223110B • IMAGE 1
DESCRIPTION
The IRE-4.0 is the dual emitter version of the IRE-3.0. It features a
unique EZ-Docker
™
plate that permits instant removal of the emitter when rearranging or servicing components. It flashes visible red
when emitting IR control signals. It has 75% lower IR output than
non-visible emitters and therefore should be used when controlling
multi-zone components to avoid cross-zone interaction. An improved
adhesive reduces callbacks for reattachment of “fallen emitters”.
ATTACHMENT
First, locate the component’s IR Sensor window (see Note 1) and
thoroughly clean it of any fingerprints or other greasy substances.
The EZ-Docker
™
port has a clear adhesive layer on its bottom surface.
Peel the protective
layer off, exposing
the adhesive.
Orient the port vertical
(see Fig. 2) and press
it over the center of the
component’s sensor
window. Press & hold
for several seconds to
ensure maximum contact
of the adhesive.
Slide the emitter from the
top down, into the EZDocker™ port. You should
feel it “snap” into place.
IRE-4.0
Dual Emitter
with Visible LED
8 FT
9/16"
7/16"
3.5mm
mini plug
Emitt ers &
Docki ng Por ts
7/16"
(–)
(+
)
Top Vi ew
NOTE: Wh ite st riped
side is pos itive (+
)
1/4"
Side View
Emitte r
Emitte r slid es int o
Dockin g Por
t
Wire Le ad
Dockin g
Por
t
Clear Adhesi ve Tape
(See N ote 3)
Fig. 1
TYPICAL INSTALLATION
Satellite Receiver
PS-1.0
IRE-4.0
Dual Emitter
with Visible LED
IRE-1.0
Emitter
IRE-4.0
Dual Emitter
with Visible LED
A/V Receiver
VCR
Hand Held
Remote
IRC-3.0
IR Sensor
Window
AT-1.0
Amplified Terminator
Unit
Power Supply
120V AC
(unswitched)
Shelf Top
IR Receiver
Fig. 3
Fig. 1
(To remove the emitter at any time, simply push upward until it
“pops” out).
Insert the 3.5mm plug into an Emitter jack on a SpeakerCraft
Terminator or other source of IR (see Fig. 3)
.
CAUTION: Do not plug into an emitter jack that is set to Blaster
Power (BL ON) or to the HIGH OUT of other connecting blocks.
To do so will smoke the emitters!!
Note 1: If you have difficulty finding the component’s IR sensor, try
using a flashlight. Sometimes the owner’s manual is helpful. You may
need to contact the manufacturer direct.
Note 2: You may also attach the emitter without the EZ-Docker
™
port. Use one of the spare adhesives (included) applying it directly to
the bottom surface of the IRE-4.0 shell.
Note 3: If you need to remove the EZ-Docker
™
port or emitter previously stuck to a component’s surface, use a fresh adhesive (included)
before reattaching.
Fig. 3
IR Controlled Components
IR Sensor
window
Docking Port
IRE-4.0 attached to
IR sensor window
2) Slide IRE-4.0 Emitter
end into docking port
1) Attach IRE-4.0 Docking Port to
IR sensor window with adhesive pad
Fig. 2
Fig. 2
Page 2
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,IRE-4.0 • LINEAR P/N: 223110B • INK: BLACK •
MATERIAL: 20LB. GLOSS WHITE PAPER • SIZE: 4.250” X 14.000” FOLD TO 4.250” X 3.500”
• FOLDING: 4 PARALLEL FAN-FOLDS, FINISH WITH LOGO SHOWING • SCALE: 1-1
223110B • IMAGE 2
2
940 Columbia Avenue, Riverside, CA 92507 • Phone 1-800-448-0976 • Fax 951-787-8747
www.speakercraft.com
LIMITED 5-YEAR WARRANTY
SpeakerCraft Inc. warrants to the original retail purchaser only that
this SpeakerCraft product will be f ree from defect s in materials and
workmanship, for a period of 5-years, provided it was purchased
from a SpeakerCraft Authorized Dealer.
Defective products must be shipped, together with proof of pur
chase, prepaid insured to the SpeakerCraft Authorized Dealer from
whom they were purchased, or to the SpeakerCraf t factor y at the
address listed on this installation instruction manual. Freight collect
shipments will be refused. It is preferable to ship this produc t in the
original shipping container to lessen the chance of transit damage.
In any case, the risk or loss or damage in transit is to be borne by
the purchaser. If upon examination at the Factory or SpeakerCraft
Authorized Dealer it is determined that the unit was defec tive in
materials or workmanship at any time during this warranty period,
SpeakerCraft or the SpeakerCraft Authorized Dealer will, at its option,
repair or replace this product at no additional charge, except as set
forth below. If this model is no longer available and can not be
repaired effectively, SpeakerCraft, at its sole option may replace the
unit with a current model of equal or greater value. In some cases
where a new model is substituted, a modification to the mount
ing surface may be required. If mounting surface modif ication is
required, SpeakerCraft assumes no responsibilit y or liability for such
modification. All replaced par ts and product become the proper ty
of SpeakerCraft Inc. Products replaced or repaired under this
warranty will be returned to t he original retail purchaser, within
a reasonable time, freight prepaid.
This warranty does not include ser vice or parts to repair damage
caused by accident, disaster, misuse, abuse, negligence, inadequate
packing or shipping procedures, commercial use, voltage input s in
excess of the rated maximum of the unit, or service, repair or
modification of the product which has not been authorized or
approved by SpeakerCraft. This warrant y also excludes normal
cosmetic deterioration caused by environmental conditions. This
warranty will be void if the Serial number on the product has be en
removed, tampered with or defaced.
This warranty is in lieu of all other expressed warranties. If the
product is defective in materials or work manship as warranted
above, the purchaser’s sole remed y shall be repair or replacement
as provided above. In no event will SpeakerCraf t be liable for any
incidental or consequential damages arising out of the use or inabil
ity to use the product, even if SpeakerCraft Inc. or a SpeakerCraft
Inc. Authorized Dealer has been advised of the possibilit y of such
damages, or for any claim by any other par ty. Some st ates do not
allow the exclusion or limitation of consequential damages, so the
above limitation and exclusion may not apply. All implied warranties
on the product are limited to the durat ion of this expressed warran
ty. Some states do not allow limitation on the length of an implied
Warranty. If the original retail purchaser resides in such a state, this
limitation does not apply.
SpeakerCraft
®
6
6
4
2
5
4
9
4
7
7
1
1
IRE-4.0
Dual IR Emitter
with Visible LED
SmartPath
™
INSTALLATION INSTRUCTIONS
LIT03400 (rev1)
223110B
ELT03400
SpeakerCraft
®
Note 4: The emitters on the IRE-4.0 are wired in series. If you cut
one off, you will need to short the cut-off wires together for the
other one to operate.
Note 5: The emitter shell and EZ-Docker
™
port, though dark in
appearance, are transparent to Infrared. This allows IR commands
to pass through them, permitting local hand held remote control as
well as through the IRE-4.0.
Loading...