Page 1
OWNER’S MANUAL
NEAT! LCR
In-Wall Speakers
NEAT! LCR Five | NEAT! LCR Three
Page 2
INTRODUCTION
Center Speaker
Congratulations on purchasing SpeakerCraft’s NEAT! LCR Series architectural loudspeakers. The NEAT! LCR Series of In-Wall speak-
ers have no external ange which means the grille material will cover the bafe and drivers and leave no additional edge between the speaker and the wall surface.
SPEAKER PLACEMENT
NEAT! LCR speakers can be used in any position of a home theater speaker system. A single NEAT! LCR can be used for the front
center channel, or a pair can be used for front or rear left and right.
Use as a Center Channel Speaker
The NEAT! LCR has been designed to blend seamlessly with all SpeakerCraft architectural in-wall and in-ceiling speakers. With
the speaker oriented horizontally, install the NEAT! LCR into the wall as close to the screen as possible. This most often means it will
need to be installed just above or below the television. Vertical alignment of the center speaker with the left and right speakers,
although not necessary, will improve the performance. (Figure 1)
Use as Front Left and Right Speakers
When using NEAT! LCRs for front left and right speakers, they should be oriented vertically with the tweeter towards the screen.
(Figure 1)
Best results are achieved when the left, right and center channel speakers are all the same distance away from the listener. The
front left and right speakers should be placed so that they form an equilateral triangle, with the listener at one point and each
speaker at the other two (Figure 2). Ideal sound will be achieved when the tweeters are placed at ear level or slightly higher. If
the speakers are positioned far away from the primary listening area, adjust the pivoting tweeters so they are pointed toward
the primary listening area. NOTE: To avoid possible damage to the pivoting tweeters, read the section entitled “SPEAKER ADJUSTMENTS” in this manual prior to performing the tweeter adjustment.
Checking for Obstructions
Before conrming the placement of the speakers, you should carefully consider the location of wall studs, electrical, plumbing
and other xtures that may get in the way. A good stud-nder, found at any building supply store, will help you determine where
the studs are located in the wall.
INSTALLATION CONSIDERATIONS
Prior to the actual installation of the speakers, it will be necessary to run cables to the speaker location from the amplifier. You will
need to run at least 16 AWG cable from the amplifier to the speaker. See your Authorized SpeakerCraft dealer for more detailed
information on cable installation. It will also be necessary to install the NEAT! Installation Bracket by following the instructions in-
cluded with the Bracket (sold separately). Preparation for and mounting of the speakers can happen at two different stages, if
you are building a new ceiling, follow the section titled INSTALLATION PREPARATION - NEW CONSTRUCTION. If you are placing the
speakers into an existing ceiling, follow INSTALLATION PREPARATION - FINISHED CEILING. There are different considerations for each
application. Please carefully follow the recommendations for your application. NOTE: A NEAT! Installation Bracket is required for
both new construction and finished ceilings. If using
drywall, no Spacer is required.
Figure 1
1
⁄2" drywall, the NEAT! Bracket Spacer is also required (sold separately). For 5⁄8"
Figure 2
1
Page 3
INSTALLATION PREPARATION - NEW CONSTRUCTION
TOP VIEW OF WA LL
First Cut
Second Cut
When installing the speakers in new construction, please follow these instructions carefully:
1. Determine Placement
Determine where in the wall the speakers will be placed using the recommendations under SPEAKER PLACEMENT. Make sure
that there are no obstructions where you plan to install the speaker. Pay careful attention to the section on avoiding obstruc-
tions and installation considerations.
2. Mount the NEAT! Installation Bracket (Part#BKT64400 sold separately)
Carefully follow the instructions included with the NEAT! Installation Bracket.
INSTALLATION PREPARATION - FINISHED CEILING
When the speakers will be installed into a finished ceiling, please follow these instructions carefully:
1. Determine Placement
Determine where in the wall the speakers will be placed using the recommendations under SPEAKER PLACEMENT. Make sure
that there are no obstructions where you plan to install the speaker. Pay careful attention to the section on avoiding obstruc-
tions and installation considerations.
2. Cut the Hole
CAUTION: This is the most important part of the entire installation. If you are not certain whether or not an obstruction exists be-
hind the desired mounting area, you should start by cutting a small hole in the center of your penciled mounting hole with a
drywall saw. Cut at a 45˚ angle towards the inside of the hole (Figure 3). Cutting the small hole at this angle will make drywall
repair much easier as the piece cut out can be installed neatly back into the hole. Once you have determined there are no
obstructions in your desired mounting location, start cutting the nished hole at a 90˚ angle to the ceiling surface.
3. Mount the NEAT! Installation Bracket (Part#BKT64400 sold separately)
Carefully follow the instructions included with the NEAT! Installation Bracket.
SPEAKER INSTALLATION
The unique integral four foot mounting system incorporated into each speaker allows for quick installation following these easy
steps:
1. If the grille is on the speaker, remove it. It may be necessary to push one or two of the mounting screws and its attached foot
towards the bafe and against the inside surface of the grille to force the grille out of its retaining groove.
2. Attach the speaker cable (observing the proper polarity with your amplier: + to + and – to –). Make sure the proper channel
of the amplier is connected to the proper speaker. Left Amp Channel to Left Speaker, Right Amp Channel to Right Speaker,
Center Amp Channel to Center Speaker, etc.
3. Make sure the mounting feet are turned inward to clear the opening, and insert the speaker into the wall. Position the speaker
into the Bracket. Tighten the 4 screws on the front of the bafe. As you tighten the screws, the feet will automatically ip into
an outward position (Figure 4), clamping the NEAT! speaker into the NEAT! Bracket. CAUTION: Over tightening may warp the
bafe, crack the wall and make the grille difcult to install.
Figure 3 Figure 4
2
Page 4
PAINTING THE SPEAKERS
When painting the speakers, the paint masks provided in the carton must be installed in place of the grille. When painting the
grilles, great care should be taken not to clog the holes, as this will greatly reduce the sound quality of the speakers. Before painting the grilles, remove the material under grille. Place this material back in place once the grille has been painted. SpeakerCraft
recommends only light spray painting using 5 parts thinning agent to 1 part paint. Do not paint the grilles while they are attached
to the speaker.
SPEAKER ADJUSTMENTS
Pivoting Tweeter Adjustment
Your NEAT! LCR Series speakers come from the factory with the tweeter facing straight out from the bafe. This will result in the overall
smoothest response. However, depending on your particular primary area, room acoustics, ceiling height, or personal preference,
you may nd the sound more pleasing by pointing the tweeters in a particular direction. If additional treble is desired in the primary
listening area, point the tweeter towards that area; and if less treble is required, point the tweeter away. Push gently at the edge of
the tweeter to point it in the desired direction (Figure 5). CAUTION: Avoid touching tweeter dome as damage WILL occur on metal
dome tweeters.
For home theater use, we recommend the following tips:
• If the speakers are being used as main front channels, the tweeter should be angled towards the listener.
• If the speakers are being used for rear surround channels, you may wish to pivot the tweeter away from the listener to achieve
a more diffused sound.
Treble Adjustment
The switch labeled TREBLE allows for 6dB of tweeter adjustment. Your speakers were shipped with the Treble switch in the ”+” position, providing +3dB of treble. If you want less treble, slide the switch to the “–” position and the tweeter will play –3dB of treble.
(Figure 6)
Figure 5
Push Tweeter Here
Figure 6
AcoustaCell 8 SYSTEM
The AcoustaCell 8 System (P/N ASM87801), sold separately, is an option for retrot installations. AcoustaCell dampens the wall
cavity and improves NEAT! LCR speaker performance. Installation can be done at the time you are ready to mount the NEAT! LCR
speakers. Please see the manual included with AcoustaCell 8 for installation instructions.
3
Page 5
SPECIFICATIONS
NEAT! LCR Five
Speaker Type:
Tweeter:
Woofers:
Impedance:
Sensitivity:
Frequency Adjustments:
Frequency Response:
Power Handling:
Dimensions (HxWxD):
Cut Out Dimensions (HxW):
Weight:
In our attempt to constantly improve our products, features and specifications are subject to change without notice.
2-Way In-Wall
Pivoting 3⁄4" Aluminum/Magnesium
Dome
Two 41⁄2" Kevlar Cones
8 ohms
90dB 1W/1m
Front-Mounted 2-Position Treble
Adjustment Switch
49Hz - 20kHz ± 3dB
90 watts
111⁄8" x 53⁄4" x 31⁄16"
(280mm x 146mm x 78mm)
61⁄8" x 113⁄8" (155mm x 289mm)
(NEAT! Installation Bracket required)
4.3 lbs (2.0 kg)
NEAT! LCR Three
2-Way In-Wall
Pivoting 3⁄4" Aluminum Dome
Two 41⁄2" Aluminum Cones
8 ohms
89dB 1W/1m
Front-Mounted 2-Position Treble
Adjustment Switch
50Hz - 20kHz ± 3dB
90 watts
111⁄8" x 53⁄4" x 31⁄16"
(280mm x 146mm x 78mm)
113⁄8" x 61⁄8" (155mm x 289mm)
(NEAT! Installation Bracket required)
4.3 lbs (2.0 kg)
4
Page 6
LIMITED LIFETIME WARRANTY
SpeakerCraft Inc. warrants to the original retail purchaser only that this SpeakerCraft product will be free from defects in materials and workmanship, provided the
speaker was purchased from a SpeakerCraft Authorized Dealer.
Defective products must be shipped, together with proof of purchase, prepaid insured to the SpeakerCraft Authorized Dealer from whom they were purchased, or to
the SpeakerCraft factory at the address listed on this installation instruction manual. Freight collect shipments will be refused. It is preferable to ship this product in the
original shipping container to lessen the chance of transit damage. In any case, the risk of loss or damage in transit is to be borne by the purchaser. If, upon examination at the Factory or SpeakerCraft Authorized Dealer, it is determined that the unit was defective in materials or workmanship at any time during this warranty period,
SpeakerCraft or the SpeakerCraft Authorized Dealer will, at its option, repair or replace this product at no additional charge, except as set forth below. If this model
is no longer available and can not be repaired effectively, SpeakerCraft, at its sole option, may replace the unit with a current model of equal or greater value. In
some cases where a new model is substituted, a modification to the mounting surface may be required. If mounting surface modification is required, SpeakerCraft
assumes no responsibility or liability for such modification. All replaced parts and product become the property of SpeakerCraft Inc. Products replaced or repaired
under this Warranty will be returned to the original retail purchaser, within a reasonable time, freight prepaid.
This Warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate packing or shipping procedures, commercial use, voltage inputs in excess of the rated maximum of the unit, or service, repair or modification of the product which has not been authorized
or approved by SpeakerCraft. This Warranty also excludes normal cosmetic deterioration caused by environmental conditions. This warranty will be void if the Serial
Number on the product has been removed, tampered with or defaced.
This Warranty is in lieu of all other expressed warranties. If the product is defective in materials or workmanship as warranted above,
the purchaser’s sole remedy shall be repair or replacement as provided above. In no event will SpeakerCraft be liable for any incidental or consequential damages arising out of the use or inability to use the product, even if SpeakerCraft Inc. or a SpeakerCraft
Inc. Authorized Dealer has been advised of the possibility of such damages, or for any claim by any other party. Some states do not
allow the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply.
All implied warranties on the product are limited to the duration of this expressed Warranty. Some states do not allow limitation on
the length of an implied warranty. If the original retail purchaser resides in such a state, this limitation does not apply.
SpeakerCraft offers a variety of accessories to make your installation of this and other SpeakerCraft products easy, economical, and professional. Contact your
authorized SpeakerCraft Dealer for more information. For technical inquires, please call 1-800-448-0976 or e-mail us at techsupport@speakercraft.com. We are
available to assist you every weekday, except holidays, between the hours of 7:00 a.m. and 5:00 p.m. PST.
940 Columbia Ave., Riverside CA 92507 | USA (800) 448 0976 Fax (951) 787 8747 International +1 951 787 0543 | www.speakercraft.com
LIT97605(rev4)
LIT64400
Loading...