SpeakerCraft AccuTuneBox Owner's Manual

OWNER’S MANUAL

MDF Subwoofer Cabinet

AccuTuneBox

AccuTuneBox 12 | AccuTuneBox 10 |AccuTuneBox 8

PRINTING INSTRUCTIONS: AccuTuneBox MANUAL - INK: BLACK - MATERIAL: 80lb Gloss - SIZE: 8.500” x 11.000”

NOTE 1:

Mounting Frame MUST be
removed from the Speaker
Baffle before installing the
Cinema In-Wall subwoofer
onto the AccuTuneBox.

NOTE 2:

Only this part of the baffle
mounts to the AccuTuneBox.
Be sure keep all included
mounting screws for installa­tion of baffle to the Accu­TuneBox. See Diagram 1

Please refer to Diagram 1 & Notes for instructions on how to install the AccuTuneBox.

INSTALLATION

STEP 1:

Using the wood screws provided,
install stud brackets to top and
bottom corners of the AccuTuneBox.

STEP 2:

Connect the speaker
cable to the negative
and positive inputs at
the top of the Accu­TuneBox.

STEP 3:

Position the AccuTuneBox
at the desired height and
fasten the stud brackets
into the studs with the
mounting screws provided.

STEP 4:

Make speaker cut-out by using
the attached plastic template
as your reference, then install
drywall to studs.

STEP 6:

Connect speaker cable to
the negative and positive
inputs of the AccuTuneBox.
Screw the sub to the back
box (and wood board insert,
if needed) using the same
screws from the baffle.

STEP 5:

Use wood board insert
only when installing into
5/8" drywall.

STEP 7:

Before proceeding, read the
Notes section below for impor­tant baffle information.

Using the original mounting
foot screws provided, install the
baffle as shown.

CAUTION: Overtightening the
screws can cause the baffle to
warp.

NOTES

DIAGRAM 1

1

PRINTING INSTRUCTIONS: AccuTuneBox MANUAL - INK: BLACK - MATERIAL: 80lb Gloss - SIZE: 8.500” x 11.000”

LIMITED LIFETIME WARRANTY

SpeakerCraft Inc. warrants to the original retail purchaser only that this SpeakerCraft product will be free from defects in materials and workmanship,
provided the speaker was purchased from a SpeakerCraft Authorized Dealer.

Defective products must be shipped, together with proof of purchase, prepaid insured to the SpeakerCraft Authorized Dealer from whom they were
purchased, or to the SpeakerCraft factory at the address listed on this installation instruction manual. Freight collect shipments will be refused. It is pref­erable to ship this product in the original shipping container to lessen the chance of transit damage. In any case, the risk of loss or damage in transit
is to be borne by the purchaser. If, upon examination at the Factory or SpeakerCraft Authorized Dealer, it is determined that the unit was defective in
materials or workmanship at any time during this warranty period, SpeakerCraft or the SpeakerCraft Authorized Dealer will, at its option, repair or replace
this product at no additional charge, except as set forth below. If this model is no longer available and can not be repaired effectively, SpeakerCraft,
at its sole option, may replace the unit with a current model of equal or greater value. In some cases where a new model is substituted, a modification
to the mounting surface may be required. If mounting surface modification is required, SpeakerCraft assumes no responsibility or liability for such modi­fication. All replaced parts and product become the property of SpeakerCraft Inc. Products replaced or repaired under this Warranty will be returned
to the original retail purchaser, within a reasonable time, freight prepaid.

This Warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate packing or
shipping procedures, commercial use, voltage inputs in excess of the rated maximum of the unit, or service, repair or modification of the product which
has not been authorized or approved by SpeakerCraft. This Warranty also excludes normal cosmetic deterioration caused by environmental conditions.
This warranty will be void if the Serial Number on the product has been removed, tampered with or defaced.

This Warranty is in lieu of all other expressed warranties. If the product is defective in materials or workmanship as warranted above, the purchaser’s
sole remedy shall be repair or replacement as provided above. In no event will SpeakerCraft be liable for any incidental or
consequential damages arising out of the use or inability to use the product, even if SpeakerCraft Inc. or a SpeakerCraft Inc.
Authorized Dealer has been advised of the possibility of such damages, or for any claim by any other party. Some states do
not allow the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply.

All implied warranties on the product are limited to the duration of this expressed Warranty. Some states do not allow limitation
on the length of an implied warranty. If the original retail purchaser resides in such a state, this limitation does not apply.

SpeakerCraft offers a variety of accessories to make your installation of this and other SpeakerCraft products easy, economical, and professional. Contact
your authorized SpeakerCraft Dealer for more information. For technical inquires, please call 1-800-448-0976 or e-mail us at [e-mail].
We are available to assist you every weekday, except holidays, between the hours of 7:00 a.m. and 5:00 p.m. PST.

SPECIFICATIONS

Baffle Wall Cut Out Dimensions:

Dimensions (HxWxD):

AccuTuneBox 12

13 3⁄8" x 13 3⁄8"

(340mm x 340mm)

59 7⁄8" x 14 3⁄8" x 3 1⁄4"

(1521mm x 365mm x 83mm)

AccuTuneBox 10

12

1

⁄8" x 12 1⁄8"

(308mm x 308mm)

42 3⁄4" x 14 3⁄8" x 3 1⁄4"

(1086mm x 365mm x 83mm)

AccuTuneBox 8

10" x 10"

(254mm x 254mm)

32 5⁄8" x 14 3⁄8" x 3 1⁄4"

(829mm x 365mm x 83mm)

In our attempt to constantly improve our products, features and specications are subject to change without notice.

2

PRINTING INSTRUCTIONS: AccuTuneBox MANUAL - INK: BLACK - MATERIAL: 80lb Gloss - SIZE: 8.500” x 11.000”

LIT67000(rev1)

940 Columbia Avenue, Riverside CA 92507 | USA [phone] Fax [phone] International [phone] | www.speakercraft.com

PRINTING INSTRUCTIONS: AccuTuneBox MANUAL - INK: BLACK - MATERIAL: 80lb Gloss - SIZE: 8.500” x 11.000”