NOTE: DO NOT OPEN THIS PRODUCT UNLESS INSTRUCTED BY STEPS INCLUDED IN
TRP & RDI 30LED INSTALLATION INSTRUCTIONS (PG 1/2)
SAVE THESE INSTRUCTIONS
WARNING! LUMINAIRES require high current and voltage.
WARNING! Fixtures must be grounded and installed in accordance with the National Electrical Code and all local codes. Failure to
do so may increase the RISK OF PERSONAL INJURY, PROPERTY DAMAGE, FIRE AND DEATH. Install and use so product does not
cause a hazard and use only in environments for which the product is specifically marked.
WARNING! This product contains chemicals known to the State of California to cause cancer, birth defects, and/or other reproductive
harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.
CAUTION! Follow ALL luminaire manufacturer's recommendations, product markings, instructions, restrictions and warnings
regarding lumninaire operation, burning position, cycling and lamp replacement. Luminaire label shows electrical and environmental
requirements.
All electrical work must be done by a qualified electrician.
Turn off electric power to all affected circuits and allow to cool before servicing.
A regularly scheduled maintenance program should be established to retain optimum light output and reduce heat retention. Dusting
with a soft, clean, dry cloth is normally sufficient for the optical assembly. Any accumulation of dust or dirt should be removed regularly.
Carefully read these instructions before installing product. If you do not understand these instructions, before starting any work, contact
your Hubbell Lighting distributor or techsupport@hubbell-ltg.com or (864) 678-1000
Give instructions to facility owner/manager for future reference.
THESE INSTRUCTIONS OR BY HUBBELL LIGHTING TECHNICAL SUPPORT PERSONNEL.
FIXTURE HAS BEEN DESIGNED WITH EASY TO INSTALL MOUNTING BRACKETS.
TOOLS REQUIRED: FLAT BLADE SCREWDRIVER OR 5/16” NUT DRIVER, DRILL, ANY
ADDITIONAL TOOLS NEEDED FOR APPROPRIATE WALL FASTENERS
PARTS REQUIRED: (SUPPLIED BY OTHERS) SILICONE CAULK, 1/4” WALL ANCHORS
AND FASTENERS APPROPRIATE FOR WALL CONSTRUCTION TYPE
CAULKING
STEP I - MOUNTING PREPARATION (Figure 1)
CAUTION:
TRP FIXTURE WEIGHS ABOUT 11 LBS
RDI FIXTURE WEIGHS ABOUT 12 LBS
Remove fixture mounting bracket from fixture by
•
loosing the two hex screws.
Align holes in bracket to matching j-box holes.
•
Secure mounting bracket to j-box.
•
If not j-box available, mounting plate must be
•
anchored to wall (hardware by others).
Pull the supply wires (C) from junction box (B).
•
Apply caulking sealant (supplied by others)
•
around the top and two sides of the bracket where
FIG. 1
C
it meets the wall.
A
B
93051033 - Page 1 of 2
701 Millennium Boulevard Greenville, SC 29607 (864) 678-1000
www.spauldinglighting.com
TRP & RDI 30LED INSTALLATION INSTRUCTIONS (PG 2/2)
Step
II WIRING
(See Fig.
2)
• Luminaire is equipped with a universal voltage driver capable of
wire. Connect
NOTE: DO NOT OPEN THIS PRODUCT UNLESS INSTRUCTED BY STEPS INCLUDED IN
SAVE THESE INSTRUCTIONS
THESE INSTRUCTIONS OR BY HUBBELL LIGHTING TECHNICAL SUPPORT PERSONNEL.
FIXTURE HAS BEEN DESIGNED WITH EASY TO INSTALL MOUNTING BRACKETS.
POWER MUST BE OFF.
(WIRING MUST BE PERFORMED BY A QUALIFIED
ELECTRICIAN)
CAUTION! SHOCK HAZARD, DO NOT CONNECT RED AND
WHITE WIRES TOGETHER UNTIL ALL OTHER
CONNECTIONS HAVE BEEN MADE.
• Wire service leads to fixture power leads according to local
and National Electric Codes.
FIG. 2
A
120V-277V input.
• For direct wire connections, connect ground wire to green
black to black and white to neutral then push
connections back inside J-box.
STEP III FIXTURE MOUNTING (See Fig. 3)
• Hold fixture at a slight angle, slide over mounting
plate and rotate upward to capture plate.
• Tighten screw (G) securely.
• Check to ensure secure mount.
• Energize product.
WARNING:
NOT DESIGNED FOR UPLIGHT
FIXTURE TO BE INSTALLED FACE
DOWN ONLY
G
B
G
FIG. 3
93051033 - Page 2 of 2
701 Millennium Boulevard Greenville, SC 29607 (864) 678-1000
www.spauldinglighting.com
Loading...