Spaulding Lighting Laredo LMC LED User Manual

93029166 - LAREDO LMC LED INSTALLATION INSTRUCTIONS

STEP I

MOUNTING PREPARATION

wall.

NOTE: DO NOT OPEN FIXTURE. FIXTURE HAS BEEN DESIGNED WITH EASY TO INSTALL

SAVE THESE INSTRUCTIONS

WARNING! LUMINAIRES require high current and voltage. HID LAMPS used in luminaires generate intense light and high

temperatures. HID LAMPS may emit UV and IR radiation. LAMPS may contain MERCURY (Hg), LEAD (Pb) and other potentially
dangerous and/or toxic materials. If lamp is marked it contains mercury and is subject to disposal laws. See www.lamprecycle.org.
HID LAMPS may rupture unexpectedly.

Hg

WARNING!

do so may increase the
gear burnouts do not cause a hazard and use only in environments for which the product is specifically marked.

WARNING!

harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.

Fixtures must be grounded and installed in accordance with the National Electrical Code and all local codes. Failure to

RISK OF PERSONAL INJURY, PROPERTY DAMAGE, FIRE AND DEATH.

This product contains chemicals known to the State of California to cause cancer, birth defects, and/or other reproductive

Install and use so lamp and control

CAUTION! Follow ALL luminaire and lamp manufacturer's recommendations, product markings, instructions, restrictions and

warnings regarding lumninaire and lamp operation, burning position, cycling and lamp replacement. Luminaire label shows electrical,
environmental and lamp requirements.
possible nuisance smoke.

All electrical work must be done by a qualified electrician.
Turn off electric power to all affected circuits and allow to cool before servicing.
A regularly scheduled maintenance program should be established to retain optimum light output and reduce heat retention. Dusting

with a soft, clean, dry cloth is normally sufficient for the reflector. Any accumulation of dust or dirt should be removed regularly from both
sides of the lens during relamping. Use only a mild soapy solution, DO NOT use alkaline or acid cleaners on reflector surfaces.

Carefully read these instructions before installing product. If you do not understand these instructions, before starting any work, contact
your Hubbell Lighting distributor or [e-mail] or [phone]

Give instructions to facility owner/manager for future reference.

MOUNTING BRACKETS.
TOOLS REQUIRED: FLAT BLADE SCREWDRIVER OR 5/16” NUT DRIVER, DRILL, ANY

ADDITIONAL TOOLS NEEDED FOR APPROPRIATE WALL FASTENERS
PARTS REQUIRED: (SUPPLIED BY OTHERS) SILICONE CAULK, TEFLON TAPE, 1/4”

WALL ANCHORS AND FASTENERS APPROPRIATE FOR WALL CONSTRUCTION TYPE

STOP USING WHEN LAMP FAILS.

Continued operation will result in control gear damage and

CAULKING

CAUTION: FIXTURE WEIGHS ABOUT 15 POUNDS

• Using mounting bracket (A) as a template, align slots in
bracket with mounting holes in junction box (B) on the

Mark hole locations (4) 4.5” square. (See Fig.1)

• Drill wall for the hardware appropriate for the type wall.
Use 1/4 diameter bolt (supplied by others) and attach
bracket to wall.

• Pull the supply wires (C) from junction box (B).

• Apply caulking sealant (supplied by others) around the
top and two sides of the bracket where it meets the wall.

4.500

4.500

C

B

FIG. 1

701 Millennium Boulevard Greenville, SC 29607 [phone]

A

1

www.hubbelloutdoor.com

INSTALLATION INSTRUCTIONS

STEP II

FIXTURE PREPARATION

(See Fig. 2)

STEP I

V FIXTURE MOUNTING

(See Fig.

4)

Step

III WIRING

(See Fig. 3)

ble of

wire. Connect

NOTE: DO NOT OPEN FIXTURE. FIXTURE HAS BEEN DESIGNED WITH EASY TO INSTALL

SAVE THESE INSTRUCTIONS

MOUNTING BRACKETS.

• Remove hub ports at (D), (E), and (F).

• Apply Teflon tape (supplied by others) to hub ports and
re-install.

REMOVE HUB PORTS

AND ADD TEFLON TAPE

D

E

F

FIG. 2

• POWER MUST BE OFF.
(WIRING MUST BE PERFORMED BY
A QUALIFIED ELECTRICIAN)

• Wire service leads to fixture power leads according to local
and National Electric Codes.

• Luminaire is equipped with a universal voltage driver capa
120V-277V input.

• For direct wire connections, connect ground wire to green
black to black and white to neutral then push

connections back inside J-box (B).

• Hold fixture at a slight angle, slide over mounting plate and
rotate downward to capture plate.

• Tighten screw (G) securely.

• Check to ensure secure mount.

• Energize product.

FIG. 3

C

A

B

FIG. 4

701 Millennium Boulevard Greenville, SC 29607 [phone]

G

2

www.hubbelloutdoor.com