Spaulding Lighting Laramie LFL User Manual

LARAMIE 1000 (LFL) INSTALLATION INSTRUCTIONS

WARNINGS:

• This product contains chemicals known to the state of California to cause

• Read and follow the lamp manufacturer’s warning and use information

• Disconnect power before installing or servicing.

• The product must be installed in accordance with the applicable installation

• Protect all wiring connections with approved insulators rated 600V. 150OC.

• Selected fixture voltage must match supply line voltage.

MOUNTING YOKE MODEL (LFL-Y) See Fig. 1:

1. Use a minimum of two 3/8” diameter bolts or one 3/4” diameter bolt for mounting.

2. Securely tighten all retaining hardware to mount fixture after aiming.

WIRING YOKE MODEL FIXTURES (LFL-Y) See Fig. 2 & 3:

1. Supply cord is to be as shown in Figure 2 and is rated for minimum 90OC 16/3

2. If not installed, assemble strain relief (A) to cord (B) as shown. Engage strain

3. Open the lens frame (E) and remove (2) screws (T) and ballast cover (U) to

4. Make wiring connections between wire cover (F) and housing.

TO CHANGE LINE VOLTAGE ON QUAD TAP BALLAST (120V THRU 277V)

5. Locate “ballast tap lead” marked “277 volt” and the black “line” lead. Disconnect

6. Replace ballast cover (U) & (2) screws (T), install lamp, and close the lens frame.

7. Close lens frame and tighten screws.

AIMING YOKE MODEL (LFL-Y) See Fig. 3 & 5:

1. Make vertical aiming adjustments by loosening bolt (Q) and rotating Yoke.

MOUNTING AND WIRING KNUCKLE MODEL FIXTURES (LFL-K)
See Fig. 4:

1. Insert set-screws (O) in the (4) tapped holes.

2. Remove (2) screws (S) and wire cover (G).

3. Place assembly on pole or bracket with tenon and orient luminaire to desired

4. Tighten (4) set-screws (O) to secure fitter to tenon.

5. Drill a 13/32” diameter hole through tenon at holes (J).

6. Remove assembly and pull line leads (L) out of the tenon allowing 8” free wires.

7. Place assembly back on tenon while guiding wire leads through wire hole (R).

8. Tighten set-screws (O) and install through bolt (H), lock washer (K) and nut (M).

CAUTION: ALWAYS SUPPORT THE FIXTURE HOUSING BEFORE ATTEMPTING

9. Make vertical aiming adjustments by loosening bolt (P) and rotating knuckle (N).

10. Make wiring connections according to the local and National Electrical Codes.

11. Bundle the wires and wrap electrical tape around to secure.

12. Replace wire cover (G).

ADJUSTING TWISTLOCK PHOTOCONTROL RECEPTACLE (See Fig. 6)

NOTES; LUMINAIRE WILL NOT OPERATE WITHOUT SHORTING CAP

FOR PROPER DRAINAGE OF FIXTURE (See Fig. 5)

SEE WARNING ON CARTON

cancer, birth defects and/or other reproductive harm. Thoroughly wash
hands after installing, handling, cleaning, or otherwise touching this product.

before installing or relamping this light fixture.

code by a person familiar with the construction and operation of the product
and the hazards involved.

SOW-A.

relief (A) to yoke bracket (C). Insert the wires into the housing and Tighten
compression cap (D) to secure cord.

expose the electrical components.

line lead from 277 volt and connect to the desired ballast voltage tap lead. Place
wirenut removed from the desired voltage tap lead on the 277 volt lead.

Maximum downward aiming is 60O below horizontal aim. Maximum upward
aiming is 80O above horizontal aim. See figure 5.

position.

Use minimum 90 C wire.

Adjust set-screws (O) as needed for leveling.

TO LOOSEN BOLT (P) TO AIM FIXTURE.

Tighten bolt securely to 20 ft-lb maximum.
Maximum downward aiming is 60O below horizontal aim. Maximum upward

aiming is 80O above horizontal aim. See figure 5.

1. Loosen two screws (V) but do not remove.

2. Rotate receptacle pointing arrow towards north.

3. Tighten back the (2) screws (V ).

OR PHOTOCONTROL SWITCH INSTALLED. DO NOT LEAVE

RECEPTACLE UNCOVERED TO THE ELEMENTS.

1. For aimed down fixtures, remove drain screw close to door hinge.

2. For aimed up fixtures, remove drain screw on top of housing.

®

V

PHOTOCONTROL
RECEPTACLE

NORTH

Hubbell Lighting, Inc. Doc. No. 93022223
A subsidiary of Hubbell Incorporated Revision C

Outdoor Lighting

701 Millennium Drive • Greenville, SC 29607 Phone [phone]

KNUCKLE

FITTER

ORIENT ARROW

PHOTOCONTROL

SWITCH

FIGURE 6
FIGURA 6

U
T

N

FIGURE 4
FIGURA 4

FIGURE 5
FIGURA 5

B

E

CORD

YOKE

KM

L

D

Q

A

1.0

60°
AIM
DOWN

DRAIN
SCREW

MOUNTING
HOLES

C

H J

O

TENON

VERTICAL

DOOR
HINGE

3.0 "

76 mm

FIGURE 3
FIGURA 3

R

S
G

P

DRAIN SCREW
TOP OF HSG

FIGURE 1
FIGURA 1

.50

12.7 mm

FIGURE 2
FIGURA 2

HOUSING

HOUSING

F

CORD

80°
AIM
UP

C
A