LOCKWASHER
HAND HOLE
LOCKWASHER
FLAT WASHER
(BY OTHERS)
FIGURES 2
LUMINAIRE TO ARM
SUPPLY
WIRES
ARM
STRAIGHT CAST ARM
DO NOT REMOVE HOLE PLUG.
FOR CURVE CAST ARM
HOUSING
GASKET
CURVE CAST ARM
REMOVE HOLE PLUG
FOR CAST
BASE COVER
POLE HARDWARE KIT)
(SHIPPED WITH
FLAT WASHER
STRAIGHT
SQUARE
POLE
(SHOWN)
SQUARE & ROUND POLES
FIGURE 5
CURVED ARM MOUNT
COVER
SCREW
CAST ARM
MEDALLION
(LUMINAIRE)
CAST ADAPTOR
ROUND
HOUSING PREPARATION
A. ARM MOUNTING INSTALLATION FOR SQUARE AND ROUND POLES
POLE
COVER
STRAIGHT SQUARE AND ROUND POLES
SQUARE
POLE
NUT PLATE
FIGURE 1
(PATTERN END)
HOUSING (3-HOLE
ARM
TO
SQ. POLE COVER
FLAT WASHER
LOCKWASHER
HEX NUT
OR MAINTENANCE
WARNING: DISCONNECT POWER BEFORE INSTALLATION
HEX NUT
NUT PLATE
ROUND POLE
CAST WALL BRACKET
FLAT WASHER
LOCKWASHER
HEX BOLT
GASKET
(PATTERN END)
HOUSING (4-HOLE
HEX BOLT
LOCKWASHER
FLAT WASHER
CAST ADPTOR
NUT PLATE
POLE COVER
POLE COVER
CAST ARM
GASKET
C. LUMINAIRE INSTALLATION TO CURVE ARM (FIGURE 5)
FIGURE 3
HOUSING (3-HOLE
(PATTERN END)
TO
WALL MOUNT
ARM
HOLE PLUG
SCREW
COVER
FIGURE 4
CURVED WALL MOUNT
HOLE PLUG
B. WALL MOUNT INSTALLATION (FIGURE 3 AND 4)
NOTE: Fixture weight is approximately 60 pounds.
DRILL (4) HOLES
J-BOX
TEMPLATE
DRILL
(4) HOLES
J-BOX
CAST ARM
(PATTERN END)
HOUSING (4-HOLE
TO
HEX NUT
CAST WALL BRACKET
FLAT WASHER
LOCKWASHER
TEMPLATE
STRAIGHT ARM
93005441
BOLTS FROM
INSIDE FIXTURE
ARM COVER
BOLT
FLAT WASHER
LOCKWASHER
BOLT
ARM COVER
FLAT WASHER
LOCKWASHER
HEX BOLT
GASKET
LOCKWASHER
FLATWASHER
SCREW
SCREW
(REV.C)
GASKET
1.
INSTALLATION INSTRUCTIONS
FOR MEDALLION 2 SERIES
HORIZONTAL SERIES REFLECTOR OPTICAL DISTRIBUTIONS
REFLECTOR
SHAPE AS
VIEWED
THRU LENS
POLE
SHAPE AS
REFLECTOR
VIEWED
THRU LENS
CENTER
POLE
LAMP
SHAPE AS
THRU LENS
VIEWED
REFLECTOR
CENTER
POLE
THRU LENS
CENTER
LAMP
REFLECTOR
SHAPE AS
VIEWED
REFLECTOR
THRU LENS
SHAPE AS
VIEWED
CENTER
POLE
POLE
POLE
POLE
POLE
POLE
LAMP
LAMP
CENTER
LAMP
VERTICAL SERIES REFLECTOR OPTICAL DISTRIBUTIONS
FLATWASHER
SCREW
TUBULAR SPACER
FLATWASHER
FIGURE 7
VANDAL SHIELD
CONTACT
PAPER
SHIELD
POLYCARBONATE
FRONT
SIDE
E. FIELD ROTATABLE OPTICS AND EXTERNAL GLARE SHIELD
NOTE: THE LIGHT WILL NOT OPERATE WITHOUT
A PHOTOCONTROL SWITCH OR A SHORTING CAP
IN PLACE. DO NOT LEAVE RECEPTACLE OPEN TO
THE ELEMENTS.
RECEPTACLE
PHOTOCONTROL
NORTH
SCREW
D. WIRING: POWER MUST BE OFF. (WIRING MUST BE
PERFORMED BY A QUALIFIED ELECTRICIAN.)
MATCH BALLAST
KNOT
NOTE: SUPPLY VOLTAGE MUST
INSIDE BALLAST AREA
TRAY REMOVED
FIGURE 6
SUPPLY
WIRES
WIRE TIE
GRN
U
H4
TYPE-IV
TYPE-V
H4P
FC
H5
TYPE-IV
H2P & H3P
TYPE-II & III
V1P
TYPE-I
TYPE-V
H5P
TYPE-IV
V4
TYPE-V
V5P
TYPE-II & III
V2P & V3P
TO CUT DOWN BACK LIGHT
DRILL (4) HOLES THRU
ON TOP OF BOSSES
USING .173" DIA. DRILL.
ON TOP OF BOSSES
USING .173" DIA. DRILL.
TO CUT DOWN EITHER LEFT
OR RIGHT SIDE LIGHT
DRILL (4) HOLES THRU
X
X
X
X
X
X
X
X
X
X
INSTALL GLARE SHIELD
USING (4) SCREWS
GLARE SHIELD
GLARE SHIELD
DRILL (4) HOLES THRU
AT DRILL POINTS USING
(.173") DIAMETER.
FC
FC
FC
2.
G. VANDAL SHIELD INSTALLATION TO FLAT GLASS ONLY
F. PHOTOCONTROL SWITCH (FIGURE 8)
FC
Loading...