INSTALLATION INSTRUCTIONS - CIMARRON LED SMALL (CL1S) SHEET 1 OF 4
SAVE THESE INSTRUCTIONS
INSTALLATION
INSTRUCTIONS
CL1S
READ THOROUGHLY BEFORE INSTALATION
WARNING!
Failure to do so may increase the
use so fixture failures do not cause a hazard and use only in environments for which the product is specifically marked.
WARNING!
reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.
CAUTION!
luminaire operation and burning position. Luminaire label shows electrical and environmental requirements and
restrictions.
All electrical work must be done by a qualified electrician.
Turn off electric power to all affected circuits and allow to cool before servicing.
A regularly scheduled maintenance program should be established to retain optimum light output and reduce heat
retention. Dusting with a soft, clean, dry cloth is normally sufficient for the optical system. Any accumulation of dust or dirt
should be removed regularly.
Carefully read these instructions before installing product. If you do not understand these instructions, before starting any
work, contact your Hubbell Lighting distributor or techsupport@hubbell-ltg.com or (864) 678-1000
Give instructions to facility owner/manager for future reference.
Fixtures must be grounded and installed in accordance with the National Electrical Code and all local codes.
RISK OF PERSONAL INJURY, PROPERTY DAMAGE, FIRE AND DEATH.
This product contains chemicals known to the State of California to cause cancer, birth defects, and/or other
Follow ALL luminaire recommendations, product markings, instructions, restrictions and warnings regarding
Install and
NOTE:
This luminare is designed for outdoor lighting applications with ambient tempertures not exceeding 40°C
WARNINGS:
Dangerous voltage exist within the unit and all precautions usually observed in handling high voltage equipment should be observed
when replacing light engine or otherwise servicing luminares. Disregarding this warning could result in electrical shock and possible
injury to the individual installing or servicing this equipment. Installation and servicing should be done by qualified personnel.
Tools Required:
Ratchet with a 3/4" Deep Socket or 3/4" Wrench
•
Torque Wrench
•
5/16" Nut Driver
•
7/16" Wrench
•
93048811 Rev.A
701 Millennium Boulevard Greenville, SC 29607 (864) 678-1000
www.hubbelloutdoor.com
INSTALLATION INSTRUCTIONS - CIMARRON LED SMALL (CL1S) SHEET 2 OF 4
SAVE THESE INSTRUCTIONS
4
1.) Mounting Preparation (See Fig. 1 & 2)
Remove door by loosening (4) 10-24 captive mounting screws.
•
Disengage safety tab at front - between opening of door and housing
•
inside unit.
Disconnect LED wire connector(s).
•
Set door assembly aside.
•
2
5
3
1
3
2.) Mounting Fixture to Pole (See Fig. 3)
Remove pole cover.
•
Attach mount plate to pole with (2) 1/2" hex bolts , lockwashers and
•
flatwashers by installing nut plate inside pole.
Torque 1/2" hex bolts to approx. 45 ft-lbs.
•
Insert the wires from the fixture through the center hole of the
•
mount plate pulling them into the pole.
11
7
6
7
9
13
8
12
8
9
8
10
4
13
7
2
4
3
1
FIGURE 1
2
5
6
12
9
8
10
11
7
FIGURE 3
Round Pole Illustration
NOTES:
For replacement LED Assemblies and Drivers please contact Hubbell Lighting for any replacement
parts.
Contact your local distributor or agent to confirm parts availability prior to ordering replacement parts.
FIGURE 2
POLE COVER
ROUND
POLE
ROUND POLE ADAPTOR
INSTALLED BETWEEN POLE
AND MOUNT PLATE,
WITH NO ADDITIONAL
HARDWARE
701 Millennium Boulevard Greenville, SC 29607 (864) 678-1000
www.hubbelloutdoor.com
INSTALLATION INSTRUCTIONS - CIMARRON LED SMALL (CL1S) SHEET 3 OF 4
SAVE THESE INSTRUCTIONS
4
3.) Mounting Fixture to Pole (See Fig. 4 & 5)
Place the Housing over the mount plate while tilting up at
•
a slight angle above horizontal, and then lower back down to
horizontal once oriented on the plate making certain the wires
are not pinched. For ease of installation, the mount plate will
hold the weight of the fixture prior to tightening the captive hex
screw.
Secure with the 1/4-20 captive hex screw already
•
in the arm of the housing.
Torque 1/4-20 hex screw to approx. 15-20 ft-lbs.
•
4
12
Wiring
POWER MUST BE OFF
••••
(Wiring must be performed by a qualified electrician)
NOTE: This LED unit is equipped with an electronic driver
•
having universal voltage adaptability and can accept input
voltage within the range of 120V - 277V or as a specified option
of 347V - 480V.
4.) Wire Connection inside Pole (See Fig. 6)
Wire service leads to fixture leads according to local and
•
National Electrical Codes.
Wire connection to be made inside pole with fixture wires and
•
supply wires (By others). Secure wires inside pole.
Connect ground wire to green wire making sure to tie in the
•
green wire from the Surge Protector, connect black to black and
white to neutral. Supply Voltage must match Driver Voltage.
Push wires back inside pole, reinstall pole cover.
•
7
12
7
FIGURE 4
5.) Reinstall Door (See Fig. 7)
Hang door in the open position by inserting the door hinge
•
pin into the slot of the hinge bracket.
Reconnect wire connector(s) to LED's.
•
Close door and re-attach with (4) 10-24 captive screws.
•
3
ARM
SUPPLY WIRES
SECURE WIRE
FIXTURE
INSIDE POLE
WIRES
FIGURE 6
POLE COVER REMOVED
12
FIGURE 5
3
NOTES:
For replacement LED Assemblies and Drivers please contact Hubbell Lighting for any replacement parts.
Contact your local distributor or agent to confirm parts availability prior to ordering replacement parts.
701 Millennium Boulevard Greenville, SC 29607 (864) 678-1000
www.hubbelloutdoor.com
FIGURE 7
INSTALLATION INSTRUCTIONS - CIMARRON LED SMALL (CL1S) SHEET 4 OF 4
SAVE THESE INSTRUCTIONS
6.) Mounting Wall Bracket (See Fig. 8)
Using template provided , locate holes in Wall Bracket
•
around junction box on the wall. Mark hole locations.
Drill wall for the hardware (supplied by others) appropriate for the wall
•
material type.
Connect extra 16 AWG wire leads (provided) inside the junction box
•
and pull wires through Wall Bracket.
Use 1/4 diameter bolts (supplied by others) and attach
•
Wall Bracket to Wall with Nut Plate inside
Apply caulking sealant (supplied by others) around the top
•
and two sides of the Wall Bracket where it meets the wall.
15
14
16
18
15
12
.
15
17
7.) Mounting Fixture to Wall Bracket (See Fig. 8)
NOTE: For this application the wire connection will be made
inside the fixture using the 16 AWG leads (provided).
Follow the steps illustrated below.
Remove existing leads and red grommet pulling them inside the
•
housing (Fig. 9).
Remove existing leads from grommet keeping the red grommet.
•
Pull 16 AWG wire leads into fixture (Fig. 10).
•
Simular to the pole mount option, go back and follow steps 2 and 3
•
in order to install the mount plate and housing.
Thread 16 AWG leads through grommet (Fig. 11).
•
Strip wires (Fig. 12)
•
Connect 16 AWG leads to Wago connectors (Fig. 13).
•
Reinstall the red grommet back into wire entry hole (Fig. 14).
•
NOTE: Make sure grommet is fully installed to prevent from voiding
•
the factory warranty (Fig. 15).
Follow same instructions as Steps 1, 2, 3 and 5 to finish installing
•
the fixture
.
Figure 9
15
FIGURE 8
Figure 10
12
17
16
14
18
Figure 11
Figure 15
Figure 12 Figure 13
NORTH
SCREW
RECEPTACLE
PHOTOCONTROL
Figure 14
PHOTOCONTROL OPTION
NOTE: THE LIGHT WILL NOT
OPERATE WITHOUT A
PHOTOCONTROL SWITCH OF A
SHORTING CAP IN PLACE.
DO NOT LEAVE RECEPTACLE
OPEN TO THE ELEMENTS.
NOTES:
For replacement LED Assemblies and Drivers please contact Hubbell Lighting for any replacement parts.
Contact your local distributor or agent to confirm parts availability prior to ordering replacement parts.
701 Millennium Boulevard Greenville, SC 29607 (864) 678-1000
www.hubbelloutdoor.com
Loading...