SparVision 200SparVision 200
SparVision 200
SparVision 200SparVision 200
V i d e o I n s p e c t i o n S y s t e mV i d e o I n s p e c t i o n S y s t e m
V i d e o I n s p e c t i o n S y s t e m
V i d e o I n s p e c t i o n S y s t e mV i d e o I n s p e c t i o n S y s t e m
Owner’s ManualOwner’s Manual
Owner’s Manual
Owner’s ManualOwner’s Manual
64026500 12-9-13
Spartan Tool LLCSpartan Tool LLC
Spartan Tool LLC
Spartan Tool LLCSpartan Tool LLC
8 0 0 . 4 3 5 . 3 8 6 6 8 0 0 . 4 3 5 . 3 8 6 6
8 0 0 . 4 3 5 . 3 8 6 6
8 0 0 . 4 3 5 . 3 8 6 6 8 0 0 . 4 3 5 . 3 8 6 6
www.SpartanTool.comwww.SpartanTool.com
www.SpartanTool.com
www.SpartanTool.comwww.SpartanTool.com
© 2013
Spartan Tool LLC
WarningWarning
Warning
WarningWarning
— Read the safety and operating instructions before using any Spartan Tool products.
Drain and sewer cleaning can be dangerous if proper procedures are not followed and appropri-
ate safety gear is not utilized.
— Before starting unit, be sure to wear personal protective equipment such as safety
goggles or face shield and protective clothing such as gloves, coveralls or raincoat, rubber boots
with metatarsal guards, and hearing protection.
— Drains and sewer can carry bacteria and other infectious micro-organisms or
materials which can cause death or severe illness. Avoid exposing eyes, nose, mouth, ears, hands
and cuts and abrasions to waste water or other potentially infectious materials during drain and
sewer cleaning operations. To further help protect against exposure to infectious materials, wash
hands, arms and other areas of the body, as needed, with hot, soapy water and, if necessary, flush
mucous membranes with water. Also, disinfect potentially contaminated equipment by washing
such surfaces with a hot soapy wash using a strong detergent.
— For any questions contact the company at the address shown below.
“California Prop. 65: This product may contain an extremely small amount of lead in the coating.
Lead is a material known to the State of California to cause cancer or reproductive toxicity.”
SPARTAN TOOL L.L.C.
1506 W. Division Street
Mendota, IL 61342
800.435.3866 u Fax 888.876.2371
www.spartantool.com
Page 2
ContentsContents
Contents
ContentsContents
Operating Section
SparVision 200 Features ............................................................................................................................................4-5
Unpacking ............................................................................................................................................................................ 6
Description .......................................................................................................................................................................... 6
Safety Instructions ........................................................................................................................................................6-8
Familiarization .............................................................................................................................................................. 9-10
iPad Application ................................................................................................................................................................ 11
Operating Instructions & Tips ............................................................................................................................... 12-13
Battery Operation and Charging ............................................................................................................................... 14
Trap-Eze (optional) ......................................................................................................................................................... 15
Maintenance ..................................................................................................................................................................... 16
Troubleshooting .............................................................................................................................................................. 17
Assembly/Part Descriptions ................................................................................................................................. 18-25
Product Information ...................................................................................................................................................... 26
Note Space ....................................................................................................................................................................... 27
Warranty Information................................................................................................................................................... 28
Page 3
SparVision 200 FeaturesSparVision 200 Features
SparVision 200 Features
SparVision 200 FeaturesSparVision 200 Features
16 GB IPAD WITH RETINA DISPLAY
9.7-inch (diagonal) LED-backlit Multi-Touch display with IPS
technology
2048-by-1536 resolution at 264 pixels per inch (ppi)
16gig On-board memory
Bluetooth 4.0 wireless technology
Built-in 42.5-watt-hour rechargeable lithium-polymer battery
Auto-sensing brightness control
CASE FEATURES
Rugged molded design
Telescoping handle
Built-in wheels
Totally enclosed, self contained circuitry
Integrated power cord storage
Easy access fuse protection
Easy access push rod
System dimensions: 22.5" x 26" x 12"
BATTERY
Batteries can be charged at any time or power level
Batteries can be charged from 110 / 220 Volt AC
Fully Charged batteries offer 4 hours of operation
PUSH CABLE
Kevlar reinforced cable jacket
Abrasion resistant jacket 200 foot length
Mounted in reel for ease of feed and retrieval
Page 4
SparVision 200 FeaturesSparVision 200 Features
SparVision 200 Features
SparVision 200 FeaturesSparVision 200 Features
SELF-LEVELING COLOR CAMERA HEAD
1.375” diameter
1.812” length
0.5 LUX sensitivity (without lights)
3.7 mm wide angle lens
768 Effective Pixel (horizontal)
494 Effective Pixel (vertical)
Optical grade, scratch resistant, clear sapphire lens
15 fully adjustable super bright white LEDs
Even light placement eliminates “hot spots”
Heavy duty, machined housing
Automatic self-leveling picture
Remarkable picture clarity and focus in lines up to 6” diameter
Operates in 1-1/2 “ straight runs, 3” sweeps and 90 degree bends
CUSTOM DESIGNED INTERFACE
Simple one-press control buttons
Movable/hideable on-screen distance counter
Movable/hideable on-screen date/time box
Reset option for distance counter
LED camera light control
Live onscreen text typing plus drawing telestrator
Quick snapshot feature for taking still images
Easy access system options
Application upgradeable via Apple software updates
Communicate files with iPad’s built in sharing tools
Built in product manual
Add custom logo to distance counter
INCLUDED ACCESSORIES
Ballistic Tough Jacket iPad case with 3-layer protection
4” Centering Guide
Flex-link with 512 Hz beacon
Page 5
UnpackingUnpacking
Unpacking
UnpackingUnpacking
Before signing the shipping receipt, check and inspect unit for visible damage. If there is visible damage,
note so on the shipping receipt.
DescriptionDescription
Description
DescriptionDescription
The system is composed of a miniature closed circuit television camera connected through flexible
push type cable. The video signal is transmitted to an iPad tablet interface via a wifi router.
This unit operates on internal battery power and 110/220 Volt AC electrical current.
Safety InstructionsSafety Instructions
Safety Instructions
Safety InstructionsSafety Instructions
WARNING: READ THE “OPERATOR’S MANUAL” THOROUGHLY BEFORE USING ANY SPARTAN TOOL
PRODUCT. DRAIN/SEWER CLEANING CAN BE DANGEROUS IF PROPER PROCEDURES ARE NOT
FOLLOWED. KNOW THE PROPER OPERATION, CORRECT APPLICATIONS AND THE LIMITATIONS OF
ALL SPARTAN TOOL PRODUCTS BEFORE USE.
CAUTION #1
Use of any electrical equipment in a wet environment can cause fatal shock if equipment is
not properly grounded, adequately maintained, and if care is not used by the operator.
A. GROUNDING INSTRUCTIONS —
Before charging your SparVision 200, make sure a properly grounded, three hole electrical outlet
is available. If not, as in some older homes, use a three-prong adapter and connect the green
pigtail (or grounding lug) to a known ground such as a cold water pipe. Never cut off the grounding
prong for use in a two hole outlet receptacle. By doing so, you have cut off your protection from
shock.
The SparVision 200 must be grounded while charging or operating using the 110V power cord to
protect the operator from electrical shock. The SparVision 200 comes with a three-conductor cord
and three-prong grounding type plug to fit the properly grounded receptacle. An adapter, see
sketches (B) and (C), is available for connecting, sketch (A) type plugs, to a two-prong receptacle,
except in Canada.
Page 6
Safety Instructions (cont.)Safety Instructions (cont.)
Safety Instructions (cont.)
Safety Instructions (cont.)Safety Instructions (cont.)
The green-colored rigid ear (or lug), extending from the adapter must be connected to a permanent
ground such as a properly grounded outlet box.
Don’t assume that all three-hole outlets are properly installed. Check the outlet and
also the adapter, if used, with an outlet testing device which quickly indicates if a ground is
connected. Correct a faulty test indication before proceeding. The use of a Ground Fault Interrupter
is the safest means to check for proper grounding.
B. EXTENSION CORDS —
Plug the power cord attached to the SparVision 200 directly into an inspected outlet. If an extension
cord must be used, it must be of an approved three-wire type in good condition, equipped with a
three-prong plug. Never cut off the grounding prong for use in a two hole outlet receptacle. By
doing so you have cut off your protection from shock.
C. OUTDOOR EXTENSION CORDS —
When Spartan Tool equipment is used outdoors, use an extension cord intended for use outdoors
and so marked.
D. AVOID ELECTRICAL CORD ABUSE —
Never move or lift Spartan Tool equipment by the cord. Do not yank cord at one end to disconnect
it from the receptacle. Keep cord away from heat, oil and sharp edges to avoid damage. Always
replace or repair damaged cords.
E. ALWAYS WEAR RUBBER BOOTS IN WET AREAS FOR ADDED PROTECTION
WARNING: SPARTAN TOOL PRODUCTS ARE NEVER TO BE OPERATED IN AN EXPLOSIVE
ENVIRONMENT.
CAUTION #2
Avoid eye or skin contact with acids or caustic substances while inspecting drains/sewers.
A. Always wear safety goggles when inspecting drain/sewers to avoid injury to eyes.
Page 7
Safety Instructions (cont.)Safety Instructions (cont.)
Safety Instructions (cont.)
Safety Instructions (cont.)Safety Instructions (cont.)
B. Before beginning work, ask the customer if either acids or caustic substances are present in the
pipe. If in doubt, litmus paper used at the opening of the pipe may give an indication of the type of
substance in the line. Litmus paper (acids/caustics) can be purchased at most pharmacies.
C. Exposure to acids or caustic substances can cause the push cable to break or to become brittle.
Depending upon the concentration of acids or caustic substances in the drain/sewer, push cables
may break or become brittle in the drum, in the pipe, or when placing the cable back into the
drum. If the push cable remains exposed to acids or caustic substances for any length of time, the
cable can continue to be damaged.
CAUTION #3
Drains/sewers carry bacteria and the possibility of infectious disease exists, if exposed.
A. Always wear safety goggles and Spartan Tool riveted gloves with rubber gloves inside the riveted
gloves to minimize exposure to infection from bacteria in pipes.
B. Avoid contact with ears, eyes, or mouth with contents of pipe to lower the risk of infection. DO
NOT SMOKE!
C. Avoid exposing any cuts to drains/sewers and sewer inspecting equipment
CAUTION #4
Follow all rules of safety and good housekeeping.
A. Keep work area clean.
B. Stay alert.
C. Place the unit and controls in a stable and accessible position for safe operation.
D. Properly store the tools.
E. Keep children away from all equipment.
F. Use only recommended equipment and accessories. Maintain tools in original working condition.
G. Do not exceed limitation of equipment or accessories.
H. Always wear recommended safety gear
I. Always lift with legs and not your back.
Page 8
FamiliarizationFamiliarization
Familiarization
FamiliarizationFamiliarization
External Reel
Connector
iPad
Lid Latch
Telescoping Handle
Push Rod Drum
Fig. 9-1
System Power
Toggle Switch
Camera
Home
Fig. 9-2
Battery Fuse
AC Fuse
Block
AC Cord
Fig. 9-3
Page 9
Centering Guide
Familiarization (cont.)Familiarization (cont.)
Familiarization (cont.)
Familiarization (cont.)Familiarization (cont.)
Flex Link with 512 Hz
Beacon Assembly
15 High Intensity LED’s
200 Feet Push Rod
Centering Guide
Locking Ring
Self Leveling
Camera Head
Page 10
iPad ApplicationiPad Application
iPad Application
iPad ApplicationiPad Application
To begin using Spartan Application, turn iPad on by pressing Home button and then slide to unlock.
Fig. 11-1
Fig. 11-2
Spartan App
Page 11
Operation InstructionsOperation Instructions
Operation Instructions
Operation InstructionsOperation Instructions
1. Flip the lid up and lift the iPad to the desired viewing location.
2. Switch the power on to begin system boot up. The system will take 60 seconds to complete its
boot up.
3. Turn on the iPad and press the Spartan Logo at the bottom of the iPad.
4. After the Spartan Tool logo appears on the screen, the main screen overlay will appear.
5. Insert camera and push cable into the pipe opening.
6. Adjust the light intesity of the camera head by pressing the camera lights button and adjusting
the intensity slider bar.
7. To use the distance counter, tap the distance counter box to open the small menu box. Press
RESET to zero the counter. The display will read 0.00 f (feet) and 0.00 m (meters). NOTE: When
pulling the push-cable out of the reel, the distance will increase. Pushing the push-cable back
into the reel will cause the distance to decrease.
8. System is now ready for pipe inspection.
NOTE - Please reference the SparVision 200 Tutorial for a complete description of the Spartan Tool
iPad Application.
Page 12
Operation TipsOperation Tips
Operation Tips
Operation TipsOperation Tips
- If you get stuck in a line, try to rotate the push-cable by hand first clockwise then counter-clockwise.
- The use of a lubricating agent on the push-cable itself can often increase the distance you are able
to push the unit. Be certain to abide by all regulations regarding the use of oils (such as vegetable
or mineral oils) or other lubricating additives down drain lines. Also, if a lubricating agent is being
used, be sure to clean push-cable before it is loaded back into the system.
- Consider using a water repellant (such as Rain-X®) on the camera lens if you are experiencing
fogging or water spotting on the camera lens in wet lines.
- If glare appears in the pipe, reduce the light intensity.
Page 13
Battery Operation & Charging
BATTERY OPERATION
The system
A fully charged battery will last approximately 4 hours.
To check battery life, choose the “Systems Options” button on the main screen. The battery gauge will
display in the lower left hand corner.
If the battery reaches a low battery state (yellow gauge color), a low battery indicator will flash on the
screen. At this point, the system should be plugged into a power source. Once the battery reaches a
critically low power level, a red flashing display will come on the screen. At this point the system will
shut down due to power failure. Again, plug in the unit as soon as possible to avoid data loss.
is designed to operate using internal battery power or 110 /220 V AC (household current).
IMPORTANT NOTE! When the low battery warning appears, end any video recording immediately.
If the power is lost during a recording session, the video file will be un-readable and can not
be recovered.
BATTERY CHARGING
110 / 220 VAC – To charge the internal battery using a 110 / 220 V power source you will need
to uncoil the AC power cord and plug the end into a AC electrical outlet. To check the charging
status, turn on the unit and choose the “Systems Options” button on the main screen. Check
the battery indicator in the lower lefthand corner. Once the batteries are fully charged, the
battery charger will automatically switch to trickle charge.
Battery Recharge Time: Approximately 4-6 hours. The unit may be left off during charging.
AC Cord
4 amp fuse
Page 14
Trap-EZE (Optional)
Part
Number Description
63050000 Trap Eze Camera System
The SparVision 200 has the ability to connect to the Trap-Eze mini reel. To use this feature, you will
need to purchase a Spartan Trap-Eze which includes a 15’ patch cable to connect the reel to the
SparVision 200.
SETUP INSTRUCTIONS
1. Turn the system power off.
2. Connect the Trap-Eze connector to the external reel connector.
3. Turn the system power on. The system will automatically switch to the Trap-EZE reel.
4. The unit is now ready for pipe inspection using the Trap-EZE.
Camera/Flex-Link
Trap-EZE
Connector
External Reel
Connection
Page 15
MaintenanceMaintenance
Maintenance
MaintenanceMaintenance
The SparVision 200 is designed for easy maintenance and trouble free operation. Regular maintenance
will prolong the life of the product. Follow these simple procedures:
t Do not store outdoors and do not allow the unit to sit for extended periods in a hot environment
such as a truck or automobile in bright sunlight.
t Never operate in standing water.
t After each inspection, always wash camera head,flex-link, and push-cable.
t The connectors may accumulate dirt on the pins with prolonged system use. Use a cotton swab
impregnated in a drop of standard alcohol to clean them. Normally a clean pin inserted in the
receptacle will wipe the internal contact and make a good connection. If this does not suffice, a
drop of alcohol can be inserted in the bad contact hole to clean it.
t Keep all connector threads clean to ensure proper tightness and mechanical connection.
t Inspect the clean push-cable for damage such as peel off, deep scratches, cracks, kinks, or any
other signs of failure.
Caution: Never use a damaged push-cable even if the system appears to function properly.
Even the smallest drop of water that penetrates will eventually corrode the wires and
produce shorts and malfunctions. Do not use electrical or other type of tape to cover a
crack or tear in any push-cable of this system.
t Wipe the camera lens cover clean with soft cloth. The cover is constructed of special scratch-
resistant, high-impact sapphire, and provides maximum transparency under adverse inspection
environment conditions.
Monitor position holding force is adjusted by
tightening/loosening of hinge crews.
Page 16
S Y M P T O M P O S SIB LE C A U S E S C O RRE C T IV E A C TIO N
N o Pow er PO W E R ON/O F F button Tu rn system on us ing pow er sw itch
h as n o t b ee n sw itch ed
Batter y m ay be run dow n Char ge battery
or oper ate sy s tem o n 110 /2 20V AC
Check battery fu se (near pow er s w itch)
N o Pow er w ith AC AC ou tlet is not pow er ed Test outlet for proper curr ent
pow er cord conne cted
AC pow er cord has fa iled Test unit us ing alternative pow er cord
AC pow er cord fuse m ay be Check the integrity of the fuse.
bl o w n
Th e po w e r unit m ay hav e failed Con tact S par ta n Tool Cu s tom er S erv ice
at (8 0 0) 43 5 -3 8 6 6 . NEVER ATTE M P T
TO R EPA IR TH E P O W ER U N IT O N
TH E P R O V ISIO N
P icture is dim o r har d The light intensity adjustm ent Use the intensity s lide b ar to in cr eas e the
to see m ay be too low ligh t intens ity
TroubleshootingTroubleshooting
Troubleshooting
TroubleshootingTroubleshooting
Page 17
SparVision Final AssemblySparVision Final Assembly
ITEM QTY PART NUMBER DESCRIPTION
1 1 61046900 BODY, CAMERA CENTERING GUIDE
2 1 61047000 LOCKING RING, CAMERA CENTERING GUIDE
3 1 62016100 FUSE, TIME DELAY5MM
4 1 63030045 FUSE, SLO-BLO
5 1 64020010 AC POWER CORD, 118" - 10A, 125 V - RED
6 1 64020050 IPAD, 4TH GENERATION - 16 GIGS - BLACK
7 1 64020090 BALLISTIC TOUGH CASE - IPAD
8 1 64020100 CAMERA-PUSHROD ASSEMBLY - COMPLETE
9 1 64021000 DRUM ASSEMBLY, SPAR-V
10 1 64022000 BASE ASSEMBLY, SPARVISION
11 1 64023000 KICKPLATE ASSEMBLY - SPARVISION
12 8 64023030 SQUARE BUMPER - 1-1/2" X 1-1/8" HGT
13 1 64023900 ASSY, RECESS PANEL - SPARVISION
6
7
13
3
4
FUSE
FUSE
SparVision Final Assembly
SparVision Final AssemblySparVision Final Assembly
Page 18
SparVision Final Assembly cont.SparVision Final Assembly cont.
1
2
9
11
5
12
10
9
11
5
6 7
SparVision Final Assembly cont.
SparVision Final Assembly cont.SparVision Final Assembly cont.
Page 19
Base AssemblyBase Assembly
ITEM QTY PART NUMBER DESCRIPTION
1 2 62016100 FUSE, 5 MM X 20 MM TIME DELAY
2 1 62016200 FUSE BLOCK, AC
3 1 63038000 ASS'Y, BASKET WIRING (2007)
4 1 63050810 STRAIN RELIEF, SNAP-IN 3/8 MNT - .19" GRIP
5 1 64022010 BRACKET, AC POWER CORD SPAR-V
6 1 64022015 BRACKET, AC RECEPTACLE 2013
7 1 64022200 ASSY, SLIPRING - ENCDR SPAR-V
8 2 64022400 WHEEL, 4" BLACK PLASTIC 3/8" BORE
9 2 64022410 PLATE, INTERIOR WHEEL MOUNT
10 2 64022420 AXLE, 4" WHEEL - 3/8" OD
11 4 64022430 SNAP RING, EXTERNAL - 3/8" SHAFT - SS
12 2 64022440 PLATE, EXTERIOR WHEEL MOUNT
13 1 64022900 LID ASSEMBLY - SPARVISION R2
14 1 64022920 PLATE, CATCH - PUSH TO CLOSE LATCH
15 2 64023030 SQUARE BUMPER - 1-1/2" X 1-1/8" HGT
16 1 64023200 BLOCK, SLIP RING COVER - SPAR-V
17 1 64023300 CAP, SLIP RING COVER - SPAR-V
18 1 64023400 PLATE, SLIP RING COVER - SPAR-V
19 1 64024200 BATTERY, SPARVISION 200
20 1 64024300 POWER SUPPLY, 3-CELL LI-ION
21 1 64026100 RUBBER CLAMP, MINI QUICK FIST
Base Assembly
Base AssemblyBase Assembly
Page 20
Base Assembly cont.Base Assembly cont.
18
16
3
15
11
12
13
5
6
10
14
8
Base Assembly cont.
Base Assembly cont.Base Assembly cont.
Page 21
Kickplate AssemblyKickplate Assembly
4
5
13
2
5
3
1
2
4
ITEM QTY PART NUMBER DESCRIPTION
1 4 63036310 SCREW, 10-32 X FLT SCK BLK
2 4 64022080 WASHER, FLAT #10 ALUM
3 4 64022655 LOCKNUT, 10-32 NYLON INSERT - ALUM
4 1 64023010 PLATE, KICKPLATE - SPARVISION
5 1 64023020 TELESCOPING HANDLE - 3-STAGE - 38"
Kickplate Assembly
Kickplate AssemblyKickplate Assembly
Page 22
Drum AssemblyDrum Assembly
8
7
5
6
5
3
8
9
11 12 2 1
ITEM QTY PART NUMBER DESCRIPTION
1 2 03850100 NUT, HEX KEP 10-32 ZINC PLTD
2 2 63032155 SCREW, BT HD 10-32 X 3/4'' BLCK
3 6 64021035 SCREW, 1/4-20 X 3/4" - BT HD SS
4 6 64021050 SCREW, 5/16-18 X 5/8 - SCK CAP
5 5 64021060 SPACER, NYLON 1/2" OD X 1/4" LONG
6 7 64021065 SPACER, 1/2" OD X 1/4" LONG NYLON
7 1 64021100 DRUM , MACHINED - SPAR-V
8 1 64021200 PLATE, DRUM TO BEARING BASE
9 2 64021220 CABLE CLAMP, 1/2" OD
10 1 64021300 BEARING, LARGE DIAMETER TURNTABLE
11 4 64022080 WASHER, FLAT #10 ALUM
12 2 64022655 LOCKNUT, 10-32 NYLON INSERT - ALUM
Drum Assembly
Drum AssemblyDrum Assembly
Page 23
Lid AssemblyLid Assembly
ITEM QTY PART NUMBER DESCRIPTION
1 2.9' 63031010 RUBBER SEAL, 3/8 X 7/32 BLACK
2 1 64022680 LATCH, SLIDE TO OPEN - BLACK
3 4 64022770 SCREW, 6-32 X 1/2 - BLK SS
4 16 64022780 LOCKNUT, 6-32 NYLON INSERT
5 1 64022910 PLATE, IPAD COMPARTMENT COVER
6 8 64022915 WASHER, PLASTIC #6 BLACK
7 12 64022925 SCREW, 6-32 X 3/8" BT HD BLCK
8 1 64022960 GRAB, UPPER PIVOT - IPAD
9 2 64022970 HINGE, TORSION - SURF MOUNT 2" LEAF
10 2 64022980 HINGE, FRICTION ADJUSTABLE 1-11/16" LEAF
11 2 64022995 SHIM, ADJUSTABLE HINGE SMALL
12 1 64027100 PLATE, UNIVERSAL TABLET MOUNT
13 1 64027200 GRAB, LOWER TABLET MOUNT
14 2 64027300 SCREW, SQR NECK BOLT 10-32 X 5/8
15 2 64027400 NUT, NYLON LOCK - 10-32 - BLCK ALUM
Lid Assembly
Lid AssemblyLid Assembly
Page 24
2
9
10
9
7
4
6
11
10
1
5
12
13
47
15
14
8
2
3
4 7
1
5
Lid Assembly Cont.Lid Assembly Cont.
Lid Assembly Cont.
Lid Assembly Cont.Lid Assembly Cont.
Page 25
64020600 - 6” Centering Guide
Product InformationProduct Information
Product Information
Product InformationProduct Information
64020500 - 2” Centering Guide
61048900 Locator with Carrying Case
63050000 Trap-Eze Camera System
Page 26
NotesNotes
Notes
NotesNotes
Page 27
ONE YEAR WARRANTY
Spartan Tool warrants its equipment to free from defects in material and workmanship for
one year from the date of purchase. To obtain warranty service, a purchaser should notify
Spartan Tool in writing, at the address provided below, within the warranty period, and Spartan
Tool will direct where to take or send the equipment for service. If the defect is covered by the
warranty, Spartan Tool will repair or replace, at its option, the defective equipment, without
charge for labor or materials. (Freight and insurance are the purchaser’s responsibility.)
This warranty is limited to the original retail purchaser and is not transferable. Spartan Tool
assumes no responsibility for damage due to accident, neglect, abuse, tampering or misuse,
nor damage from repairs or alterations by others. This warranty does not cover damage to
the equipment resulting from the use of replacement parts other than Spartan Tool parts.
Spartan Tool’s sole obligation and the original retail purchaser’s exclusive remedy under this
warranty shall be for repair or replacement as described above. ALL OTHER WARRANTIES,
WHETHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
NO EVENT SHALL SPARTAN TOOL BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
SPARTAN TOOL L.L.C.
MENDOTA, ILLINOIS 61342
Spartan Tool L.L.C. reserves the right to make changes at any time, without notice, to specifications and models and also discontinue models. The right is also reserved to change specifications or parts at any time without incurring any obligation to equip same on models manufactured
prior to the date of change.
SPARTAN TOOL L.L.C.
1506 W. Division Street
Mendota, IL 61342
800.435.3866 u Fax 888.876.2371
www.spartantool.com
Page 28
Loading...