Spartan TE256 User Manual

TE256

Programmable Digital 6-Port Valve and Modulating Fan

Thermostats

CLIENT USER MANUAL

Front view Back view

# Item Description

LCD Display temperature and working status.

1

MODE button Access to user and engineer menu and for setting

2

FAN button Toggle to change Fan mode: Auto or Continuous

3

UP & DOWN buttons Increase & decrease setting or previous/next item

4

SET button Setting for schedules and Timers

5

On/Off button Turn on/ off Valve and Fan

6

Set-point icons Displaying set-point temperature while it is flashing

7

Fan icons Indicate Fan status

8

Flake icon Indicate working on Cooling mode;

9

Hot spring icon Indicate working on Heating mode

10

Flow icon NA

11

Gear icon Indicate cooler is ON

12

Clock NA

13

Sleep NA

14

Moon Sign Indicating room is unoccupied via occupancy contact

15

Outdoor icon NA

16

Cover screw Screw to tighten back cover with front cover

17

Back plate Plate for mounting on electric box

18

Wiring terminal blocks Terminals for wiring

19

Mounting holes Holes for mounting on electric box

20

Time Display time

21

Schedule number Current Schedule running or setting

22

Day Current day of Sunday ~ Saturday or setting

23

1074-2-1-04

Revised Date: 2017/01/24

confirmation or change ℃/℉ unit if press for over 3 sec.

1

Operation

User Mode Operation

The first tier of operation includes the following settings as Figure 2. To operate:

1. Power switch “ON” or “OFF” to start/ stop the System;

2. After switching “ON”, press any button to start the User Mode operation.

i. Press “MODE” button to switch over different working modes. When MODE is pressed for more than 3

seconds, the unit of temperature will toggle to change to ℉ or ℃.

ii. Press UP/ DOWN button to increase/ decrease or rotate the values of setting.

iii. Press “FAN” button to toggle over different fan modes.

iv. Press “SET” button to set current time-date and timer. When SET is pressed for more than 3 seconds,

users can set the temperature schedules.

3. It will return to normal display with the latest setting if there’s no button pressed for 10 seconds.

# Item Description Remarks

Normal Display Display Current Room or Set-Point

1

Temperature Setting View Current Set Point or Set The

2

Temperature and Current Time-Day.

Required Temperature

Setting “-SP- “Parameter in Engineer Table to Choose Current Room or Set-Point Temperature.

Mode Select 1. Select The Working Mode:

3

Fan Auto/ Continuous 1. Change Fan Mode for Auto or

4

Time/ Date/ Schedule

5

Setting

SET

(1) Run/ Halt/ Stop for Schedule

2. When MODE Is Pressed For More Than 3 Seconds, The Unit Of Temperature Will Toggle To Change To ℉ Or ℃.

Continuous Mode.

2. Auto Mode Will Stop Fan Output During Dead Band

3. Continuous Mode Will Output Low Speed During Dead Band

1. Set Current Time in 12- Or 24- Hour Format;

2. Set Calendar and Day of Week;

3. When SET Is Pressed for More Than 3 Seconds, Users Can Set Temperature Set Points Schedules

RUN: Run Schedules. HALT: Pause “Current” Schedule

and Use Manual SP. STOP: Stop Using All Schedules and Use Manual SP.

Low Speed Can Be Set Via Engineer Table

Press SET to Continue Settings. Press MODE, FAN, Or POWER Button to Escape Any Time During Setting.

Special:

1. Fan bar will be shown according to the fan output from low or minimum speed to 100% of max fan output.

2. The icon , , , or will be shown on LCD while the Schedule 1,2,3, or 4 is running or being set.

3. If press “MODE” button, there are three schedule modes “RUN, HALT, and STOP” for selection.

a.) RUN mode means activating Schedules. And at the same time an icon ( ~ ) will be steadily shown

on the LCD.

b.) HALT mode means temporarily pause current schedule and using manual S.P instead. And the icon

(

~ ) will be flashing on the LCD.

Revised Date: 2017/01/24

2

c.) STOP mode means stop to use manual S.P until manually activate schedule again. And the icon

( ~ ) will be NOT shown on the LCD.

Fig. 2 User Mode operation sequence

Overview for the settings of Clock and Schedules

 Press MODE, FAN, or POWER button to escape any time during setting.

Revised Date: 2017/01/24

3

Revised Date: 2017/01/24

4

1. Detailed State Diagram for Clock Setting

Revised Date: 2017/01/24

5

Set points

Set

points

Press MODE button to

Set points

2. Detailed State Diagram for Schedule Setting

Press “Mode” button to select (day shows steadily)/ deselect (day flash).

Press MODE button to toggle Cooling/ Heating

Revised Date: 2017/01/24

Press MODE button to toggle Cooling/ Heating

toggle Cooling/ Heating

6

Default Set Point Schedules

COOL Sun Mon Tue Wed Thu Fri Sat

Sch. 1

Sch. 2

Sch. 3

Sch. 4