SparkLAN Communications WPEB263ACNIBT Users Manual

Wireless Module

All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice.

www.sparklan.com / [e-mail] / [phone]

WPEB-263ACNI(BT)

ver.1.0

Standards

IEEE 802.11ac/a/b/g/n (2T2R)

Bluetooth V4.1,V4.0 LE, V3.0+HS, V2.1+EDR

Chipset

Broadcom

Data Rate

802.11b: 11Mbps / 802.11a/g: 54Mbps / 802.11n: MCS0~15/ 802.11ac: MCS0~9

Bluetooth: 1 Mbps, 2Mbps and Up to 3Mbps

Operating Frequency

IEEE 802.11 ac/a/b/g/n ISM Band, 2.400GHz~2.497GHz, 4.900GHz~5.845GHz

*Subject to local regulations

Interface

PCle: WLAN / USB: Bluetooth

Form Factor

Half Mini PCIe

Antenna

2xIPEX MHF4 connectors (ANT0 for WIFI+BT, ANT1 for WIFI)

Modulation

WiFi :

802.11b : DQPSK、DBPSK、CCK

802.11g/n : OFDM /64-QAM、16-QAM、QPSK、BPSK

802.11a : OFDM /64-QAM,16-QAM, QPSK, BPSK

802.11n : OFDM /64-QAM,16-QAM, QPSK, BPSK

802.11ac : OFDM /256-QAM

BT :

FHSS, GFSK, DPSK, DQPSK

Power Consumption

TX: 610mA / RX: 285mA

Operating Voltage

DC 3.3V

Operating Temperature Range

-40°C~+85°C

Storage Temperature Range

-40°C~+85°C

Humidity
(Non-Condensing)

10%~90% (Operating)

5%~90% (Storing)

Dimension (in mm)

29.85mm (± 0.15mm) x 26.65mm (± 0.15mm) x 2.64mm (± 0.2mm)

Weight (g)

≦ 6g

Driver Support

Windows 10, Linux, Android

Security

64/128-bits WEP, WPA, WPA2, 802.1x

Specification

WPEB-263ACNI(BT)

Wireless Module

All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice.

www.sparklan.com / [e-mail] / [phone]

WPEB-263ACNI(BT)

ver.1.0

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FOR MOBILE DEVICE USAGE (>20cm/low power)

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator &

your body.

This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20 cm is maintained between the antenna and users,

2) The transmitter module may not be co-located with any other transmitter or antenna.

3) Module approval valid only when the module is installed in the tested host or compatible series of host

which have similar RF exposure characteristic with equal or larger antenna separation distance.

Wireless Module

All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice.

www.sparklan.com / [e-mail] / [phone]

WPEB-263ACNI(BT)

ver.1.0

As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM

integrator is still responsible for testing their end-product for any additional compliance requirements

required with this module installed

IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop

configurations or co-location with another transmitter), then the FCC authorization is no longer considered

valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will

be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC

authorization.

End Product Labeling

FOR MOBILE DEVICE USAGE (>20cm/low power)

This transmitter module is authorized only for use in device where the antenna may be installed such that

20 cm may be maintained between the antenna and users. The final end product must be labeled in a

visible area with the following: “Contains FCC ID: RYK-WPEB263ACNIBT”. The grantee's FCC ID can be used

only when all FCC compliance requirements are met.

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to install or

remove this RF module in the user’s manual of the end product which integrates this module.

The end user manual shall include all required regulatory information/warning as show in this manual.