SparkLAN Communications WMIA139AG Users Manual

WMIA-139AG IEEE 802.11a Mini-PCI User’s Maunal

Specification

Product Name 54 Mbps/ 11Mbps Wireless LAN MINIPCI Card
Model Number WMIA-139AG
Host Interface MINIPCI
Dimensions 59.7x50.95x5 mm
Weight 20g
Frequency Band

802.11a

Unlicensed National Information Infrastructure (U-NII) frequency band,

5.15GHz to 5.85GHz (subject to local regulations)

Number of Non-Overlapping
Channels

Operating Voltage 3.3V ± 5%
Modulation

Data Rate

Security

Antenna Interface

Transmitted power

Receive Sensitivity

802.11a

USA and Canada-13
Europe – up to 19, subject to local regulations
Japan – 4

802.11a: OFDM;

802.11a

54, 48, 36,24,18,12, 9, 6 Mbps per channel, auto fallback for extended
range; (option : Enhanced proprietary Turbo Mode up to 108 Mbps)

802.11a

64/128/152-bit WEP Encryption, AES

UFL-CON

802.11a

802.11a

Nominal Temp Range:

please see the output power table for detail.

- 6Mbps 10-5 BER @ -90dBm, typical

- 9Mbps 10-5 BER @ -89dBm, typical

- 12Mbps 10-5 BER @ -88dBm, typical

- 18Mbps 10-5 BER @ -87dBm, typical

- 24Mbps 10-5 BER @ -83dBm, typical

- 36Mbps 10-5 BER @ -80dBm, typical

- 48Mbps 10-5 BER @ -74dBm, typical

- 54Mbps 10-5 BER @ -70dBm, typical

802.11a

Supplied Driver Windows 98SE/ME/NT4.0/2000/XP

Max.2W
Continue Tx : 560 mA @ 3.3V
Continue RX : 350 mA @3.3V

Standards

Warranty 1 year
Temperature Range 0 ~ 50°C (Operating); -20 ~ 85°C (Storing)
Operating Humidity 10% to 85% Non-Condensing

Operating Range Open Space: Up to 260 m: Indoor: 100 m

Network Protocol TCP/IP, IPX, NDIS4, and NDIS5 ,NDIS 5.1
Management Utility Monitor Internet Access Status via UI
EMC certification

System Requirements Laptop PC containing

IEEE 802.3, IEEE 802.3u, IEEE 802.11a,

draft standard ,Wi-Fi compliant

Storage Humidity 5% to 90% Non-Condensing

The transmission speed varies in the surrounding environment

TBD

(FCC part 15C/15.247; ETS 300 328-2; UL; IEC60950; EN

301 489-1,17; prEN50371; CE Mark; TELEC)

Æ MINIPCI local bus slot
Æ 64MB memory or greater
Æ 300MHz processor or greater

Microsoft Windows 98 Second Edition/Millennium Edition/2000/NT 4.0
with Service Pack 6,Windows XP

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not
expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

Statement Needed to be Shown on End Product

Since this module is installed inside the end product, the end product should be
affixed a label on visible area showing that this product contain a RF module, and
also its FCC ID.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an