Space Pak ECOELEGANT SERIES, HW~ECM SERIES Installation, Operation And Service Manual

ECOELEGANT SERIES

INSTALLATION OPERATION AND SERVICE

MANUAL (AMERICAS VERSION)

HW~ECM SERIES

Revised: July 11, 2016

Page 1 of 57

SK2016 HW-V-AECM-001

INVESTING IN QUALITY, RELIABILITY & PERFORMANCE.

ISO 9001 QUALITY

World Leading Design and Technology

Every product is manufactured to meet the stringent requirements of the internationally recognized ISO 9001 standard for quality assurance in design, development and production.

Equipped with the latest air-conditioning test rooms and manufacturing technology, our factories in China produce over 2,000,000 air conditioning units each year, all conforming to the highest international standards of quality and safety.

ETL SAFETY STANDARDS

The Highest Standards of Manufacturing

All products conform to UL standard for Safety for Heating and Cooling Equipment UL1995 4th Edition, October 14, 2011;

All products conform to CSA standard for Safety for Heating and Cooling Equipment CSA C22.2 No.236-11, 4th Edition, October 14 2011.

In order to guarantee the very highest standards and performance, we manage every stage in the manufacturing of our products. Throughout the production process we maintain strict control, starting with our extensive resources in research and development through to the design and manufacture of almost every individual component, from molded plastics to the assembly of units and controllers.

WEEE MARK

Quality Controlled from Start to Finish

All products conform to the “WEEE”

directive to guarantee correct standards of environmental solutions.

Our highly trained staff and strict quality control methods enable us to produce products with an exceptional reputation for reliability and efficiency, maintained over many years. As well as full CE certification and ISO 9001, several products ranges have UL / ETL safety approval in the USA and Canada, ROHS compliance for Europe, giving you the confidence of knowing our company is the right choice when selecting air conditioning equipment.

ALWAYS MAKE SURE THIS MANUAL REMAINS WITH THE UNIT. READ THIS MANUAL BEFORE PERFORMING ANY OPERATION ON THE UNIT.

Page 2 of 57

SK2016 HW-V-AECM-001

Table of Content

A. GENERAL DESCRIPTION ................................................................................................................................................. 4

B. TECHNICAL DATA .......................................................................................................................................................... 5

B.1. GENERAL SPECIFICATION .................................................................................................................................................... 5

B.1.1. HW–AECM Series Specifications ............................................................................................................................. 5

B.2. COIL DATA ...................................................................................................................................................................... 6

B.2.1. 2-Pipe Systems ........................................................................................................................................................ 6

B.5. VALVE INFORMATION ...................................................................................................................................................... 11

B.5.2. 3-Way 1/2” Valve Body......................................................................................................................................... 11

C. SERVICE AND INSTALLATION ....................................................................................................................................... 12

C.1. INSTALLATION OF HIGH-WALL UNIT ................................................................................................................................... 12

C.1.1. Selecting a Location .............................................................................................................................................. 12

C.1.2. Mounting Plate Dimensions .................................................................................................................................. 13

C.1.3. Installing the Mounting Plate ............................................................................................................................... 14

C.1.4. Drilling the Condensate Drainage Hole................................................................................................................. 14

C.1.5. Installing the Hydronic Unit .................................................................................................................................. 15

C.1.6. Drainage Piping Works ......................................................................................................................................... 15

C.2. UNIT MAINTENANCE AND PREPARATION............................................................................................................................. 16

C.2.1. Opening and Closing Of Lift-Up Grille Cover ......................................................................................................... 16

C.2.2. Removing Front Cover Assembly .......................................................................................................................... 16

C.2.3. Air Purging ............................................................................................................................................................ 17

C.2.4. Wiring Connections ............................................................................................................................................... 17

C.3. PIPE CONNECTIONS WITH VALVE ....................................................................................................................................... 18

D. CONTROL SPECIFICATIONS: COMPLETE CONTROL PCB - S TYPE CONTROL ................................................................... 19

D.1. DEFINITION OF INPUT/OUTPUT ......................................................................................................................................... 19

D.2. WIRING DIAGRAM FULL CONTROL PCB – S CONTROL TYPE ................................................................................................... 20

D.3. CONFIGURATION SETTINGS............................................................................................................................................... 21

D.4. CONTROL LOGICS FOR 2-PIPE SYSTEM................................................................................................................................ 23

D.4.1. With Thermoelectric Valve Configuration ............................................................................................................ 23

D.4.2. Without Thermoelectric Valve Configuration ....................................................................................................... 26

D.5. CONTROL LOGICS FOR 4-PIPE SYSTEM................................................................................................................................ 28

D.6. SLEEP MODE .............................................................................................................................................................. 30

D.7. AUTO FAN SPEED ........................................................................................................................................................... 30

D.8. LOUVER ........................................................................................................................................................................ 31

D.9. BUZZER ........................................................................................................................................................................ 31

D.10. AUTO RESTART .............................................................................................................................................................. 31

D.11. OPERATION OF CONTROL PANEL ON HIGH-WALL UNIT ........................................................................................................ 31

D.11.1. On/Off Switch .................................................................................................................................................. 31

D.11.2. Electric Heater Safety Switch (on control PCB) ................................................................................................ 31

D.13. LED DISPLAY AND ERROR DESCRIPTION .............................................................................................................................. 33

D.14. LED DISPLAY ON MASTER/SLAVE CONNECTION.................................................................................................................... 34

E. NETWORKING SYSTEM ................................................................................................................................................ 35

E.1. MASTER – SLAVE NETWORK ............................................................................................................................................. 35

E.1.1. Master – Slave Network Setup ............................................................................................................................. 36

E.1.2. Master-Slave Communication Method ................................................................................................................. 39

E.2. UNIT NETWORK WIRING SCHEME ..................................................................................................................................... 40

E.3. OPEN MODBUS PROTOCOL .............................................................................................................................................. 41

F. CONTROL SPECIFICATIONS: FLEXIBLE CONTROL PCB - W TYPE CONTROL .................................................................... 45

F.1. DEFINITION OF INPUT/OUTPUT ......................................................................................................................................... 45

F.2. WIRING DIAGRAM FLEXIBLE CONTROL PCB - W CONTROL TYPE .............................................................................................. 46

F.3. ONBOARD CONFIGURATION .............................................................................................................................................. 47

F.4. CONTROL LOGICS ........................................................................................................................................................... 48

F.5. LED DISPLAY ................................................................................................................................................................. 48

F.6. ERROR DESCRIPTION ....................................................................................................................................................... 48

Page 3 of 57

SK2016 HW-V-AECM-001

G. USERS INTERFACE ....................................................................................................................................................... 49

G.1. REMOTE CONTROL HANDSET ............................................................................................................................................ 49

G.2. WIRED WALL PAD .......................................................................................................................................................... 50

G.2.1. Wall Pad Display .............................................................................................................................................. 50

G.2.2. Wall Pad Operation Guidelines ........................................................................................................................ 51

G.2.3. EC unit RPM setting ......................................................................................................................................... 54

H. SENSOR RESISTANCE R-T CONVERSION TABLE ............................................................................................................ 55

I. TROUBLESHOOTING GUIDE ......................................................................................................................................... 57

Page 4 of 57

SK2016 HW-V-AECM-001

A. General Description

This High-Wall Unit is designed to meet and exceed demanding requirements for efficiency, quiet operation and appearance. The sleek profile and elegantly styled cabinet complements any interior design theme, while the microprocessor assures accurate environmental control.

Cabinet ~ the stylish cabinet is constructed of durable flame resistant acrylonitrile-butadiene-styrene (ABS) plastic. The silver white color and rounded corners provide its modern look.

Water Coil ~ the water coil has a large heat transfer surface and utilizes the latest fin profile technology. It combines an advanced technology approach with the security of a traditional design regar din g tube thickness. The water coil is also equipped with an air vent valve and a water purge valve.

Integral Hoses ~ an integral hose is a synthetic elastomer tube, with stainless steel outer braiding and brass connectors, which enables quick, low cost connections with no brazing.

Blower and Motor ~ the unit incorporates only specially designed and tested EC motors, allowing the blower wheel to provide optimum performance in airflow-efficiency and quiet operation.

Filters ~ washable, easy-to-remove, fine mesh air filters are standard to all high-wall models. Tabs located on the front of the unit can be unsnapped, allowing the filter to be easily slid downward and removed. No tools are required, nor any dismantling of the equipment.

Air Grille Distribution ~ all units are equipped with both deflector blades and independent directional vanes, enabling supply air to be automatically distributed, and air flow and direction to be customized.

Microprocessor Control ~ see Controls Specifications for complete control specifications and details. The main design features include:

~ FCEER rating class: A/B. ~ FCCOP rating class: B/C. ~ High efficiency EC motor with PID algorithmic processing in auto-mode. ~ 2-pipe, 2-pipe with booster electric heat, 2-pipe with primary electric heat, 4-pipe with 4x2 device

installed. ~ Cool, Heat, Auto, Dehumidifier and Fan modes. ~ Sleep, Auto-Fan, Daily Timer, Auto-Restart with memory functions. ~ User friendly remote control handset. ~ Heat and cool temperature protections and safety cut out. ~ 2-way and 3-way on/off valve control. ~ Addressable control and error diagnostics (Master-Slave) for sub-networks of up to 32 units, with IR

handset as global control interface. ~ Wired wall pad controller (optional) with 7-day programmable timer, real-time clock, network control

(global and addressable) and error diagnostics. ~ Manual control panel in cabinet. ~ Auxiliary switch for cooling and heating signal. ~ Occupancy (remote on/off) contacts / economy mode contacts. ~ Open Modbus communication protocol. ~ Local PC host control solution (optional).

Page 5 of 57

SK2016 HW-V-AECM-001

B. Technical Data

B.1. General Specification

B.1.1. HW–AECM Series Specifications

Product range: HW-AECM Hydronic High Wall 2 pipe with EC Motor (American Standard)

HW-[Size]-V~-AECM

04

06

12

15

18

20

24

30

Unit

Configuration

2-pipe

Number Of Fan Blowers

Single

Power Supply

(V/Ph/Hz)

220 or 115/1/60

Operation Control

~S: Complete function onboard PCB with integrated group control functionality.

~W: Flexible function onboard PCB with drain pump, louver and zone control functionality.

Performance Data

Air

Air Flow

H

CFM

218

294

379

464

576

635

729

M

171

218

294

435

447

576

635 L 129

171

218

335

353

447

Cooling

Cooling Capacity

H

BTU/Hr

4158

6967

8394

10207

12602

16293

18174

20249

M

3497

5534

6277

8394

11069

13254

16293

17493

L

2833

4620

5486

6339

9040

11393

13254

Sensible Cooling Capacity

H

2936

4889

5822

7126

8808

11171

12499

13969

M

2458

3856

4313

5822

7702

9034

11171

12018

L

1979

3202

3754

4357

6247

7734

9034

Heating

Heating Capacity

H

BTU/Hr

6653

11147

13430

16331

20163

26069

29078

32398

M

5595

8854

10043

13430

17710

21206

26069

27989

L

4533

7392

8778

10142

14464

18229

21206

Max. Electric Heater Capacity@115V

1700

2500

Max. Electric Heater Capacity@220V

3400

5100

Electrical

Fan motor power

H W 13

18

26

30

40

50

M

10

13

20

30

40 L 6

10

13

15

19

25

Fan Motor Running Current @ H 115V

A

0.16

0.284

0.364

0.544

0.696

1.04

1.5

Fan Motor Running Current @ H 220V

A

0.08

0.142

0.182

0.272

0.348

0.52

0.75

Soun

d

Sound PressureLevel

dB(A)

31/26/24

39/31/26

40/33/28

45/34/31

49/44/37

43/39/36

47/43/37

50/47/40

Sound Power Level

40/35/33

48/40/35

49/42/37

54/43/40

58/53/46

52/48/45

56/52/46

59/56/49

Hydraulic

Cooling Water Flow Rate

H

GPM

0.83

1.39

1.68

2.03

2.52

3.25

3.63

4.04

M

0.70

1.10

1.25

1.68

2.20

2.65

3.25

3.49 L 0.56

0.92

1.09

1.26

1.81

2.27

2.65

Cooling Pressure Drop

H

Ft.wg

6.18

7.53

6.37

8.92

6.12

11.92

14.33

17.33

M

4.61

5.09

3.88

6.37

4.91

8.33

11.92

13.42

L

3.23

3.75

3.09

3.95

3.48

6.47

8.33

Heating Water Flow Rate

GPM

Same as "Cooling Water Flow Rate"

@H/M/L

Heating Pressure Drop

H

Ft.wg

4.95

6.03

5.09

7.13

4.89

9.53

11.47

13.87

M

3.69

4.07

3.11

5.09

3.93

6.67

9.53

10.73

L

2.58

3.00

2.47

3.16

2.79

5.17

6.67

Water Content

gal

0.01

0.02

0.03

0.05

0.07

Construction and

Package Data

Water

Type

Socket (NPT Threaded Female)

Connections

In

in

1/2"

Out

Condensate Drainage Connection

0.63

Dimensions

L

in

34.45

41.34 W 8.66

9.25 H 11.81

12.2

Net Weight

lbs

24.3

26.5

28.7

30.9

35.3

a. Cooling mode (2-pipe): b. Heating mode (2-pipe):

- Return air temperature: 80.0F DB/ 67.0F WB. - Return air temperature: 70F.

- Inlet/ outlet water temperature: 45F/55F. - Inlet water temperature: 140F.

- Water flow-rate: same as cooling mode.

Page 6 of 57

SK2016 HW-V-AECM-001

B.2. Coil Data

B.2.1. 2-Pipe Systems

Model

Fin Height

(inch)

Fin Length

(inch)

Fins per Inch

No. of Rows

No. of Copper

No. of Circuits

Tube

Diameter

(inch)

HW‐04

9.1

26.8

19.5

2 8 2

0.3

HW‐06

14.1

26.8

2

20 4 0.3

HW‐12

14.1

26.8

2

26 5 0.3

HW‐15

14.1

26.8

2

26 5 0.3

HW‐18

14.1

26.8

2

34 5 0.3

HW‐20

14.9

33.3 2 36 6 0.3

HW‐24

14.9

33.3

2

36 6 0.3

HW‐30

14.9

33.3 2 36 6 0.3

Page 7 of 57

SK2016 HW-V-AECM-001

B.3. Sound Power and Pressure data

Sound Power

A-weighted Sound Power dB(A)

31.0

29.2

27.8

43.1

33.9

29.9

43.1

33.9

29.9

50.1

37.1

33.6 Sound Power in 1/3 Octave

-bands (unit dB)

31.5Hz

4.6

10.4

11.5

2.3

0.9

4.1

11.5

0.9

4.1

10.3

5.4

8.9

63Hz

3.1

3.5

4.9

0.8

5.5

3.4

10.0

5.5

3.4

13.0

3.8

2.3

125Hz

6.2

7.5

6.2

7.8

8.4

5.5

17.0

8.4

5.5

22.2

11.7

8.7

250Hz

17.5

13.5

10.1

21.1

22.5

17.8

30.3

22.5

17.8

38.3

25.3

23.7

500Hz

23.0

17.8

13.0

25.9

26.6

21.2

35.1

26.6

21.2

41.7

30.5

26.1

1000Hz

19.8

15.2

12.8

23.1

21.1

16.3

32.3

21.1

16.3

40.2

26.4

20.9

2000Hz

16.0

15.2

14.8

16.8

16.9

15.1

26.1

16.9

15.1

35.8

20.4

17.0

4000Hz

15.4

15.6

15.4

9.1

15.8

15.3

18.3

15.8

15.3

26.1

16.4

15.9

8000Hz

14.6

14.3

5.5

14.9

14.4

14.8

14.9

14.4

17.1

14.9

14.7

16000Hz

7.4

8.6

7.8

-1.2

7.8

7.9

8.0

7.8

7.9

8.0

Speed H M L H M L H M L H M L

Model

HW-04

HW-06

HW-12

HW-15

A-weighted Sound Power dB(A)

53.7

48.6

41.3

46.8

43.4

40.1

49.8

46.8

40.1

55.7

52.1

43.4

Sound Power in 1/3 Octave

-bands (unit dB)

31.5Hz

3.6

3.9

11.5

16.8

8.3

12.3

12.8

16.8

12.3

17.1

9.4

8.3

63Hz

22.3

14.5

11.1

17.2

11.2

11.8

12.3

17.2

11.8

22.4

18.0

11.2

125Hz

27.2

20.4

15.0

21.2

18.5

14.9

23.0

21.2

14.9

26.0

25.2

18.5

250Hz

42.3

36.1

29.5

32.8

29.7

25.5

35.0

32.8

25.5

40.6

38.1

29.7

500Hz

45.8

40.3

35.1

38.4

36.5

33.0

41.5

38.4

33.0

47.0

44.6

36.5

1000Hz

43.9

38.5

31.4

36.2

32.9

29.3

39.9

36.2

29.3

46.3

42.1

32.9

2000Hz

40.7

33.8

24.4

29.4

25.4

26.7

33.7

29.4

26.7

40.9

36.6

25.4

4000Hz

31.7

24.5

17.9

21.3

18.8

32.2

24.6

21.3

32.2

33.8

28.3

18.8

8000Hz

20.4

16.1

15.0

15.5

15.8

33.0

16.9

15.5

33.0

21.2

18.6

15.8

16000Hz

8.2

10.7

7.8

6.9

27.1

10.9

6.9

27.1

8.2

7.0

6.9

Speed H M L H M L H M L H M L

Model

HW-18

HW-20

HW-24

HW-30

Page 8 of 57

SK2016 HW-V-AECM-001

Sound Pressure

A-weighted Sound Pressure dB(A)

21.8

20

18.6

33.8

24.6

20.7

33.8

24.6

20.7

40.9

27.9

24.3

Sound Pressure in 1/3 Octave

-bands (unit: dB)

31.5Hz

-4.7

1.2

2.2

11.5

-8.4

-5.1

2.3

-8.4

-5.1

1.1

-4.6

-3.8

63Hz

-6.1

-5.7

-4.3

10.0

-3.8

-5.9

0.8

-3.8

-5.9

3.8

-6.2

-5.4

125Hz

-3.0

-1.7

-3.1

17.0

-0.8

-3.8

7.8

-0.8

-3.8

12.9

1.7

2.5

250Hz

8.2

4.3

0.9

30.3

13.2

8.6

21.1

13.2

8.6

29.0

15.3

16.1

500Hz

13.8

8.6

3.8

35.1

17.3

11.9

25.9

17.3

11.9

32.4

20.5

21.3

1000Hz

10.6

5.9

3.5

32.3

11.9

7.1

23.1

11.9

7.1

31.0

16.4

17.2

2000Hz

6.8

6.0

5.6

26.1

7.7

5.9

16.8

7.7

5.9

26.6

10.3

11.1

4000Hz

6.2

6.4

6.2

18.3

6.6

6.1

9.1

6.6

6.1

16.9

6.3

7.1

8000Hz

5.4

5.1

14.8

5.7

5.1

5.5

5.7

5.1

7.8

4.9

5.7

16000Hz

-1.9

-0.6

-1.5

8.0

-1.4

-1.3

-1.2

-1.4

-1.3

-2.2

-1.4

Speed H M L H M L H M L H M L

Model

HW-04

HW-06

HW-12

HW-15

A-weighted Sound Pressure dB(A)

44.4

39.4

32

37.5

34.2

30.9

40.5

37.5

30.9

46.5

42.9

34.2

Sound Pressure in 1/3 Octave

-bands (unit: dB)

31.5Hz

-5.7

-5.3

2.2

7.6

-0.9

3.1

3.6

7.6

3.1

7.9

0.1

-0.9

63Hz

13.1

5.3

1.9

7.9

2.0

2.5

3.1

7.9

2.5

13.2

8.8

2.0

125Hz

17.9

11.2

5.8

12.0

9.3

5.7

13.7

12.0

5.7

16.8

16.0

9.3

250Hz

33.1

26.9

20.3

23.6

20.5

16.3

25.8

23.6

16.3

31.3

28.8

20.5

500Hz

36.6

31.1

25.9

29.1

27.3

23.8

32.3

29.1

23.8

37.7

35.4

27.3

1000Hz

34.7

29.3

22.2

27.0

23.7

20.1

30.7

27.0

20.1

37.1

32.9

23.7

2000Hz

31.5

24.6

15.2

20.2

16.2

17.4

24.5

20.2

17.4

31.6

27.4

16.2

4000Hz

22.5

15.3

8.7

12.1

9.6

23.0

15.4

12.1

23.0

24.5

19.1

9.6

8000Hz

11.2

6.9

5.7

6.3

6.5

23.8

7.7

6.3

23.8

12.0

9.3

6.5

16000Hz

-1.1

1.5

-1.4

-2.3

-2.4

17.9

1.7

-2.3

17.9

-1.0

-2.2

-2.4

Speed H M L H M L H M L H M L

Model

HW-18

HW-20

HW-24

HW-30

Page 9 of 57

SK2016 HW-V-AECM-001

B.4. Dimensional Drawings

Dimensional drawing for HW-04/06/12/15/18-AECM

Model

Unit Dimensions

A B C D E F G

H

HW-04/06/12/15/18

1.57

4.13

34.45

2.17

4.13

R0.78

2.36

2.91

(All dimensions shown in inch)

Model

Unit Dimensions

a b c d e f g

h

HW-04/06/12/15/18

7.87

2.17

1.18

8.66

9.02

0.39

11.81

Model

Unit Dimensions

1 2 3

4

HW-04/06/12/15/18

26.18

6.69

27.95

4.92

Page 10 of 57

SK2016 HW-V-AECM-001

Dimensional drawing for HW-20/24/30-AECM

Model

Unit Dimensions

A B C D E F G

HW-20/24/30

3.54

41.34

2.01

3.54

0.59

2.87

2.91

Model

Unit Dimensions

1 2 3

4

HW-20/24/30

33.66

6.10

32.28

6.89

(All dimensions shown in inch)

Model

Unit Dimensions

a b c d e f g

h

HW-20/24/30

8.46

2.05

1.18

1.26

9.25

12.20

2.28

0.51

Page 11 of 57

SK2016 HW-V-AECM-001

B.5. Valve Information

B.5.1. 2-Way 1/2” Valve Body

B.5.2. 3-Way 1/2” Valve Body

Differential Pressure Chart

Valve Model

Valve Dimensions (inch)

DN A B C D

SGS14HFCA-23020201

D15

(G1/2”)

2.05

1.85

0.77

2.48

Valve Model

Valve Dimensions (inch)

DN A B C D

SGS14HFCA-23020202

D15

(G1/2”)

2.05

2.76

1.57

3.39

Page 12 of 57

SK2016 HW-V-AECM-001

C. Service and Installation

Operating Limits

Power supplies

Volt

Phase

Hz

Model

208~240

1

60

HW-VX-AECM

110~120

1

60

HW-VY-AECM

Water circuit

Minimum entering water temperature

+2°C (35.6°F)

Maximum entering water temperature

+80°C (176°F)

Water side recommended maximum pressure

1600 kPa (232 PSI)

C.1. Installation of High-Wall Unit

C.1.1. Selecting a Location

Select the location for the high-wall unit with the following considerations in mind:

1. The front of the air inlet and outlet should be clear of any obstructions. The air should flow freely.

2. The wall where the unit is to be mounted should be solid enough not to resonate and produce noise.

3. The location should allow easy access to install the connecting water pipes, and be where drainage can be easily

achieved.

4. Ensure the clearance around the fan coil unit conforms to the following drawing.

5. From the floor the height of the unit should be above eye level.

6. Avoid installing the unit in direct sunlight.

* Required clearance for maintenance and servicing is as shown above. ** All dimensions shown in mm.

7. The signal receiver on the unit must be kept away from any high frequency emission source.

8. Keep the unit away from fluorescent lamps, which may affect the control system.

9. To avoid electromagnetic control system interference, ensure control wires are installed separately from 110-

240 VAC power supply wires.

10. Where electromagnetic waves are present, use shielded sensor cables.

11. Install a noise filter if the power supply creates any disruptive noises.

Higher than eye level

Page 13 of 57

SK2016 HW-V-AECM-001

C.1.2. Mounting Plate Dimensions

HW-04/06/12/15/18 –AECM

HW-20/24/30 –AECM

(All dimensions shown in inch)

Page 14 of 57

SK2016 HW-V-AECM-001

C.1.3. Installing the Mounting Plate

1. Select the structural position (e.g. a pillar or lintel) on the wall.

2. Then temporarily fasten the mounting plate on the wall with a steel nail.

3. Mount the mounting plate horizontally as shown in the above

figure or by means of gradiometer. Failure to follow this may

cause water to drip indoors and create atypical noise.

4. Fix the mounting plate by means of expansion screws or

tapping screws.

C.1.4. Drilling the Condensate Drainage Hole

1. Ensure that the hole for condensate drainage is correctly positioned. The height should be lower than the

bottom edge of the indoor unit.

2. Drill a 65mm diameter hole with a descending slope.

3. Seal it off with putty after installation.

Page 15 of 57

SK2016 HW-V-AECM-001

C.1.5. Installing the Hydronic Unit

1. Pass the piping through the hole in the wall and hook the indoor unit on the mounting plate by the upper hooks.

2. Move the body of the unit from side to side to verify if it is securely fixed.

3. While pushing the unit toward the wall, lift it slightly from beneath to hook it up on the mounting plate by the

lower hooks.

4. Make sure the unit firmly rests on the hooks of the mounting plate.

C.1.6. Drainage Piping Works

1. Install the drain hose so that it slopes downward slightly for free drainage. Avoid installing it as shown in the

below illustrations marked with an “X”.

2. Put water in the drain pan and make sure that the water drains outdoors.

3. If the flexible drain hose provided with the indoor unit is not long enough, please extend it by joining it to an

extension hose (not provided). Be sure to insulate the connecting part of the extension drain hose with a shield pipe as shown.

4. If the attached drain hose passes through an indoor area, insulate it with heat insulation material.

Page 16 of 57

SK2016 HW-V-AECM-001

C.2. Unit Maintenance and Preparation

C.2.1. Opening and Closing Of Lift-Up Grille Cover

Open the grille cover by lifting from the bottom position indicated by the arrows.

Close the grille cover by pressing down at the positions indicated by the arrows.

C.2.2. Removing Front Cover Assembly

1. Set the horizontal louver to the horizontal position.

2. Remove the screw caps below the louver, and then remove the mounting screws.

3. Open the lift-up grille cover by grasping the panel at both sides as shown above.

4. Remove the remaining screws located in the center of the front cover.

5. Grasp the lower part of the front cover and pull the entire assembly out and up towards you.

Page 17 of 57

SK2016 HW-V-AECM-001

C.2.3. Air Purging

1. After connecting the water inlet and outlet pipes to the main supply lines turn on the main breaker and operate

the unit in COOLING mode.

2. Open the water inlet valve and flood the coil.

3. Check all connections for water leakage. If no leak is found, open the purging valve with an open end wrench

while supporting the unit with your other hand. Then purge the air trapped inside the coil. When performing this activity, take care not to touch the electrical parts.

4. Close the purging valve when no bubbles appear.

5. Open the water outlet valve.

C.2.4. Wiring Connections

Unit components are wired to the terminal block of the indoor unit. Wiring can be accessed from the terminal block inside the control box.

Page 18 of 57

SK2016 HW-V-AECM-001

C.3. Pipe Connections with Valve

Pre-assembly

Complete Assembly

Flexible hose

Valve body with actuator

½” gasket

Coil connector

Page 19 of 57

SK2016 HW-V-AECM-001

D. Control Specifications: Complete Control PCB - S Type Control

Used in all High-Wall [V/P] ~S unit configurations.

Abbreviations

Ts = Setting temperature Tr = Room air temperature Ti1 = Chilled water coil temperature Ti2 = Hot water coil temperature

AUX1 = Hot water free contact AUX2 = Chilled water free contact MTV1 = Chilled Motorized valve MTV2 = Hot Motorized valve

D.1. Definition of Input/Output

I/O

Code

2-Pipe

4-Pipe

Analogue Input

Return air sensor

AI1

Return air temperature (Tr)

2-pipe coil circuit sensor

AI2

Chilled / hot water coil circuit (Ti1)

Chilled water coil circuit (Ti1)

Hot water sensor

AI3

N/A

Hot water coil circuit (Ti2)

Input

LED display / IR receiver

X-DIS1

Digital communication port to LED display / IR receiver board.

Wired wall pad

TTL1

Digital communication port to wired wall pad board.

Digital input

Occupancy contact

On/Off

Window contacts: for remote ON/OFF (when DIPB SW1 = 1). Economy contacts: for remote activation of economy

mode (when DIPB SW1 = 0).

Electrical heater safety switch

EH

Voltage-free (NC). The contact is closed before the EH is turned on.

Power input

Phase

L1

Power supply: 220V/1Ph/60Hz 115V/1Ph/60Hz Neutral

N1

Earth

PE1

Voltage output

Fan

CN4

Fan driver

Valve 1

MTV1

2-pipe coil circuit valve output – chilled / hot water valve. Voltage output (L)

2-pipe coil circuit valve output – chilled water valve. Voltage output (L)

Valve 2

MTV2

Reserved

4-pipe coil circuit valve output – hot water valve. Voltage output (L)

Voltage of electrical heater (Live)

HEAT

Voltage output (L), maximum 25 A

Output

Stepping motor

CN1 / CN2

Louver stepping motor relay

Auxiliary contact 2

AUX2

Cooling mode signal relay (NO). Voltage free contact. To ensure the sensitivity of the connection, please make sure max wiring length < 100ft

Auxiliary contact 1

AUX1

Heating mode signal switch (NO). Voltage free contact. To ensure the sensitivity of the connection, please make sure max wiring length < 200” 100ft

Serial BUS port

CN3

Master-slave network serial connection OR MODBUS / local PC host network serial connection.

Page 20 of 57

SK2016 HW-V-AECM-001

D.2. Wiring Diagram Full Control PCB – S Control Type

Page 21 of 57

SK2016 HW-V-AECM-001

D.3. Configuration Settings

There are 2 DIP switches set on the PCB:

1. DIPA-S1 (8 positions)

 SW1 – SW6: used for master-slave / BMS network address.  SW7 – SW8: used for operating mode configuration.

2. DIPB-S2 (6 positions)

 SW1: Occupancy / economy mode selection.  SW2: 2-pipe / 4-pipe configuration selection.  SW3: Thermoelectric valve configuration selection (2-pipe system only).  SW4: Pre-heat protection temperature selection.  SW5 – SW6: brushless DC fan motor configuration.

Default DIP Switch Settings:

Figure 1

DIPA –S1 DIPB –S2

Figure 2

3. Thermoelectric Valve Configuration:

On board DIP switch SW3 of DIPB is used for this configuration.

SW3

Thermoelectric valve (MTV)

1

With valve

0

No valve

Unit Configuration

WITHOUT Valve

Unit Configuration

WITH Valve

0=OFF 1=ON

Page 22 of 57

SK2016 HW-V-AECM-001

4. Unit Configuration:

On board DIP switches of DIPB are used for the below configurations.

SW1

PR-O contact setting

0

Economy contact

1

Window contact

SW2

System setting

0

2-pipes system

1

4-pipes system

SW4

Preheat setting

1

82.4°F

0

96.8°F

5. Motorized Fan Speed Settings for Different Models on DIPB:

Unit Model

Speed (RPM)

SW3

SW5

SW6

Low

Medium

High

HW-04

500

600

700 0 0 0 HW-06

600

700

900 0 1 0 HW-12

600

700

950 0 0 1 HW-15

700

800

1100 0 1 1 HW-18

900

1100

1300 1 0 0 HW-20

800

900

1100 1 0 1 HW-24

900

1100

1200

1 1 0

HW-30

900

1200

1350 1 1 1 Default RPM

900

1200

1350 1 1

1

6. Mode configuration:

DIPA-S1

Model

SW7

SW8

Model setting

0

Cool-Heat

0 1 Cool-Heat + booster heater

1

0

Cooling only

1

Cool + primary heater

7. Air Conditioner ON/OFF

There are 3 ways to turn the system on or off:

a) By the ON/OFF button on the handset or wired wall pad. b) By the programmable timer on the handset or wired wall pad. c) By the manual control button on the air conditioner.

8. Power On Setting a) Handset only user interface: When the power ON signal is received by the air conditioner, the Mode, Fan

Speed, Setting temperature and Swing setting will be the same as the handset setting before the last power OFF.

b) Wall-pad only OR wall-pad and handset user interface: When the power ON signal is received by the air

conditioner, the Mode, Fan Speed, Setting temperature, Swing setting and Timer ON/OFF weekly program will be the same as the wall pad setting before the last power OFF.

Page 23 of 57

SK2016 HW-V-AECM-001

D.4. Control Logics For 2-Pipe System

D.4.1. With Thermoelectric Valve Configuration

COOL MODE

a) MTV2, AUX1 and heater are always off. b) If Tr ≥ Ts + 1.8ºF (or + 7.2ºF if economy contact is activated), then cool operation is activated and MTV1

and AUX2 are turned on. Indoor fan runs at set speed.

c) If Tr < Ts, then cool operation is terminated and MTV1 and AUX2 are turned off. Indoor fan runs at set

speed.

d) The range of Ts is 60.8 - 86ºF e) Indoor fan speed can be adjusted to low, medium, high and auto. f) When turned on, MTV1 requires 30 seconds before it is fully open. g) When turned off, MTV1 requires 120 seconds before it is fully closed. h) When the unit is turned off, the indoor fan will shut down after 5 seconds.

LOW TEMPERATURE PROTECTION OF INDOOR COIL

a) If Ti1 ≤ 35.6ºF for 2 minutes, then MTV1 and AUX2 are turned off. If indoor fan is set for low speed, it will

run at medium speed. If it is set at medium or high speed, it will keep running at the same speed.

b) If Ti1 ≥ 41ºF for 2 minutes, then MTV1 and AUX2 are turned on. Indoor fan runs at set speed.

FAN MODE

a) Indoor fan runs at the set speed while heater, MTV1, MTV2, AUX1 and AUX2 are turned off. b) Indoor fan speed can be adjusted to low, medium and high.

HEAT MODE

Without Electrical Heater

a) MTV2, AUX2 and heater are always off. b) If Tr ≤ Ts﹣1.8ºF (or – 7.2ºF if economy contact is activated), then heat operation is activated and

MTV1 and AUX1 are turned on. Indoor fan runs at the set speed.

c) If Tr > Ts, then heat operation is terminated and MTV1 and AUX1 are turned off. Indoor fan runs at

200RPM.

d) The range of Ts is 60.8 - 86ºF. e) Indoor fan speed can be adjusted to low, medium, high and auto. f) When turned on, MTV1 requires 30 seconds before it is fully open. g) When turned off, MTV1 requires120 seconds before it is fully closed.

With Electrical Heater as Booster

a) MTV2 and AUX2 are always off. b) If Tr ≤ Ts﹣1.8ºF (or – 7.2ºF if economy contact is activated), then heat operation is activated and MTV1

and AUX1 are turned on. Indoor fan runs at the set speed.

c) If Tr > Ts, then heat operation is terminated and MTV1 and AUX1 are turned off. Indoor fan runs at

200RPM.

d) If Ti1 < 104ºF, then the electrical heater is turned on. If 104ºF ≤ Ti1 < 113ºF, then the electrical heater

maintains its original state. If Ti1 ≥ 113ºF, then the electrical heater is turned off.

e) The range of Ts is 60.8 - 86ºF. f) Indoor fan speed can be adjusted to low, medium, high and auto. g) When turned on, MTV1 requires 30 seconds before it is fully open. h) When turned off, MTV1 requires 120 seconds before it is fully closed.

Page 24 of 57

SK2016 HW-V-AECM-001

With Electrical Heater as Primary Heat Source

a) MTV1, MTV2, and AUX2 are always off. b) If Ti2 ≤ 86ºF (or Ti2 is damaged or not connected),

1) If Tr ≤ Ts﹣1.8ºF (or – 7.2ºF if economy contact is activated), then heat operation is activated

and the electrical heater and AUX1 are turned on. Indoor fan runs at set speed.

2) If Tr > Ts, then heat operation is terminated and the electrical heater and AUX1 are turned off.

Indoor fan runs at 200RPM.

c) If Ti2 > 86ºF, MTV2 and AUX2 are off.

1) If Tr ≤ Ts﹣1.8ºF (or – 7.2ºF if economy contact is activated), then heat operation is activated

and the electrical heater is turned off while MTV1 and AUX1 are turned on. Indoor fan runs at set speed.

2) If Tr > Ts, then heat operation is terminated and MTV1 and AUX1 are turned off. Indoor fan

runs at 200RPM.

d) The range of Ts is 60.8 - 86ºF. e) Indoor fan speed can be adjusted to low, medium, high and auto.

PRE-HEAT

Without Electrical Heater

a) If Ti1 < 96.8ºF (or 82.4ºF depending on DIP setting), then MTV1 and AUX1 are turned on, indoor fan

runs at 200RPM.

b) If Ti1 ≥ 100.4ºF (or 86ºF depending on DIP setting), then MTV1 and AUX1 are turned on, indoor fan

runs at set speed.

c) If the indoor coil temperature sensor is damaged, then the pre-heat time is set for 2 minutes. Indoor

fan runs at set speed.

With Electrical Heater

a) If the indoor fan speed ≥ 300rpm, then the electrical heater will turn on.

POST-HEAT

Without Electrical Heater

a) If Ti1 ≥ 100.4ºF, then MTV1 and AUX1 are turned off. Indoor fan continues to run at set speed. b) If 96.8F ≤ Ti1 ≤ 100.4F, then MTV1 and AUX1 are turned off. Indoor fan maintains its original state. c) If Ti1 < 96.8ºF, then MTV1 and AUX1 are turned off. Indoor fan runs at 200RPM. d) If the indoor coil temperature coil is damaged, then the post-heat time is set for 3 minutes with the

indoor fan running at set speed.

With Electrical Heater

a) Indoor fan will run at 200rpm before the unit turns off for 20 seconds.

OVER-HEAT PROTECTION OF INDOOR COIL

a) If Ti1 ≥ 167ºF, then MTV1 and AUX1 are turned off. Indoor fan remains on and runs at high speed. b) If Ti1 < 158ºF, then MTV1 and AUX1 are turned on. Indoor fan remains on and runs at set speed. c) If the indoor coil temperature sensor is damaged, then the protection mode will be overridden and the

unit will work according to the pre-heat and post-heat program.

Page 25 of 57

SK2016 HW-V-AECM-001

DEHUMIDIFICATION MODE

a) MTV2, AUX1 and heater are always off. b) If Tr ≥ 77ºF, then MTV1 and AUX2 will be turned on for 3 minutes, and then off for 4 minutes. c) If 60.8ºF ≤ Tr < 77ºF, then MTV1 and AUX2 will be turned on for 3 minutes, and then off for 6 minutes. d) If Tr < 60.8ºF, MTV1 and AUX2 will be turned off for 4 minutes. e) At the end of the above dehumidification cycle, the system will decide the next dehumidification control

option. Indoor fan will run at low speed throughout the dehumidification process.

AUTOMODE

Without Electric heater and With Electric Heater as Booster

a) Every time the unit is turned on, MTV1 is on while AUX1, AUX2 and fan are off. MTV2 and the heater are

always off. After 120 seconds, the subsequent operation mode is decided according to the following:

i. If the coil temperature sensor (Ti1) ≥ 96.8°F, then MTV1, AUX1 and fan turn on or off according to

HEAT mode.

ii. If Ti1 < 96.8°F, then MTV1, AUX2 and fan turn on or off according to COOL mode.

b) Unit remains in AUTO COOL or AUTO HEAT mode throughout the operating cycle until the user changes

the mode manually or restarts the unit.

c) Should the Ti1 sensor fail or be damaged, auto mode will not function.

With Electric Heater as Primary Heat Source

a) If the current running mode is AUTO COOL mode, it will change over to AUTO HEAT mode upon satisfying

all the conditions below:

i. Ts - Tr ≥ 1.8°F (or – 7.2ºF if economy contact is activated).

ii. MTV1 has stopped ≥ 10 minutes.

b) If the current running mode is AUTO HEAT mode, it will change over to AUTO COOL mode upon satisfying

all the conditions below:

i. Tr - Ts ≥ 1.8°F (or – 7.2ºF if economy contact is activated).

ii. MTV1 has stopped ≥ 10 minutes.

Note: AUTO COOL or AUTO HEAT operations are the same as COOL or HEAT mode respectively.

Page 26 of 57

SK2016 HW-V-AECM-001

D.4.2. Without Thermoelectric Valve Configuration

COOL MODE

a) Heater, AUX1, MTV1 and MTV2 are always off. b) If Tr ≥ Ts + 1.8ºF (or + 7.2ºF if economy contact is activated), then cool operation is activated and AUX2

is turned on. Indoor fan runs at set speed.

c) If Tr < Ts, then cool operation is terminated and AUX2 is off. Indoor fan runs at 200rpm. d) The range of Ts is 60.8 - 86F. e) Indoor fan speed can be adjusted to low, medium, high and auto. f) When the unit is turned off, indoor fan shut down after 5 seconds.

LOW TEMPERATURE PROTECTION OF INDOOR COIL

a) If Ti1 ≤ 35.6ºF for 2 minutes, then AUX2 is turned off. If low speed is selected via user interface, then

indoor fan runs at medium speed. If medium or high speed is selected via user interface, then indoor fan runs at set speed.

b) If Ti1 ≥ 41ºF for 2 minutes, then AUX2 is turned on. Indoor fan runs at set speed.

FAN MODE

a) Indoor fan runs at the set speed while heater, AUX1, AUX2, MTV1 and MTV2 are turned off. b) Indoor fan speed can be adjusted to low, medium and high.

HEAT MODE

Without electrical heater

a) MTV1, MTV2, AUX2 and heater are always off. b) If Tr ≤ Ts – 1.8ºF (or – 7.2ºF if economy contact is activated), then heat operation is activated and AUX1

is turned on. Indoor fan runs at the set speed.

c) If Tr > Ts, then heat operation is terminated and AUX1 is turned off. Indoor fan runs at 200rpm. d) The range of Ts is 60.8 - 86ºF. e) Indoor fan speed can be adjusted to low, medium, high and auto.

With electrical heater as booster

a) MTV1, MTV2 and AUX2 are always off. b) If Tr ≤ Ts – 1.8ºF (or – 7.2ºF if economy contact is activated), then heat operation is activated and AUX1

is turned on. Indoor fan runs at the set speed.

c) If Tr > Ts, then heat operation is terminated and AUX1 is turned off. Indoor fan runs at 200 rpm. d) If Ti1 < 104ºF, then the electrical heater is turned on. If 104ºF ≤ Ti1 < 113ºF, then the electrical heater

maintains its original state. If Ti1 ≥ 113ºF, then the electrical heater is turned off.

e) The range of Ts is 60.8 - 86ºF. f) Indoor fan speed can be adjusted to low, medium, high and auto.

Page 27 of 57

SK2016 HW-V-AECM-001

PRE-HEAT

Without Electrical Heater

a) MTV1, MTV2 and AUX2 are off. b) If Ti1 < 96.8ºF (or > 82.4ºF is selected by DIPB-S2 position SW4), then AUX1 is turned on while indoor

fan remains off.

c) If Ti1 ≥ 100.4ºF (or < 86ºF is selected by DIPB-S2 position SW4), then AUX1 is turned on while indoor

fan runs at set speed.

d) If the indoor coil temperature sensor is damaged, then the pre-heat time is set for 2 minutes and the

indoor fan runs at set speed.

With Electrical Heater

a) If the indoor fan speed ≥ 300RPM, then the electrical heater will turn on.

POST-HEAT

With and Without Electrical Heater

a) AUX1 is turned off. Electrical heater is turned off. b) Indoor fan will shut down after the unit has been turned off for 20 seconds.

LOW TEMPERATURE PROTECTION OF INDOOR COIL

a) If Ti1 ≤ 35.6ºF for 2 minutes, then AUX2 is turned off. If indoor fan runs at low speed, then it will run at

medium speed. If indoor fan runs at medium or high speed, then it will run at set speed.

b) If Ti1 ≥ 41ºF for 2 minutes, then AUX2 is turned on. Indoor fan runs at set speed.

OVER-HEAT PROTECTION OF INDOOR COIL

a) If Ti1 ≥ 167ºF, then AUX1 is turned off. Indoor fan remains on and runs at high speed. b) If Ti1 < 158ºF, then AUX1 is turned on. Indoor fan remains and runs at set speed. c) If the indoor coil temperature sensor is damaged, then the protection mode will be overridden and the

unit will work according to the pre-heat and post-heat program.

DEHUMIDIFICATION MODE

a) MTV1, MTV2, AUX1 and heater are always off. b) If Tr ≥ 77ºF, then the indoor fan and AUX2 will be turned on for 3 minutes, and then off for 4 minutes. c) If 60.8ºF ≤ Tr < 77ºF, then the indoor fan and AUX2 will be turned on for 3 minutes, and then off for 6

minutes.

d) If Tr < 60.8ºF, then the indoor fan and AUX2 will be turned off for 4 minutes. e) At the end of the above dehumidification cycle, the system will decide the next dehumidification

control option. Indoor fan will run at low speed throughout the dehumidification process.

AUTO-MODE

Not available.

Page 28 of 57

SK2016 HW-V-AECM-001

D.5. Control Logics For 4-Pipe System

Note: unit equipped with 4x2 switching device.

COOL MODE

a) MTV2, AUX1 and Electrical Heater are always off. b) If Tr ≥ Ts + 1.8ºF (or + 7.2ºF if economy contact is activated), then cool operation is activated, MTV1

and AUX2 are turned on. Indoor fan runs at set speed.

c) If Tr < Ts, then cool operation is terminated, MTV1 and AUX2 are turned off. Indoor fan runs at set

speed.

d) The range of Ts is 60.8 - 86ºF e) Indoor fan speed can be adjusted to low, medium, high and auto. f) When turned on, MTV1 requires 30 seconds before it is fully open. g) When turned off, MTV1 requires 120 seconds before it is fully closed. h) When the unit is turned off, the indoor fan will shut down after 5 seconds.

FAN MODE

a) Indoor fan runs at the set speed while heater, MTV1, MTV2, AUX1 and AUX2 are turned off. b) Indoor fan speed can be adjusted to low, medium and high.

HEAT MODE

Without Electrical Heater

a) MTV1, AUX2 and electric heater are always off. b) If Tr ≤ Ts – 1.8ºF (or – 7.2ºF if economy contact is activated), then heat operation is activated and MTV2

and AUX1 are turned on. Indoor fan runs at the set speed.

c) If Tr > Ts, then heat operation is terminated and MTV2 and AUX1 are turned off. Indoor fan runs at

200RPM.

d) The range of Ts is 68.8 - 86ºF. e) Indoor fan speed can be adjusted to low, medium, high and auto. f) When turned on, MTV2 requires 30 seconds before it is fully open. g) When turned off, MTV2 requires120 seconds before it is fully closed.

With Electrical Heater as Booster

a) MTV1 and AUX2 are always off. b) If Tr ≤ Ts – 1.8ºF (or – 7.2ºF if economy contact is activated), then heat operation is activated and MTV2

and AUX1 are turned on. Indoor fan runs at the set speed.

c) If Tr > Ts, then heat operation is terminated and MTV2 and AUX1 are turned off. Indoor fan runs at

200RPM.

d) If Ti1 < 104ºF, then the electrical heater is turned on. If 104ºF ≤ Ti1 < 113ºF, then the electrical heater

maintains its original state. If Ti1 ≥ 113ºF, then the electrical heater is turned off.

e) The range of Ts is 60.8 - 86ºF. f) Indoor fan speed can be adjusted to low, medium, high and auto. g) When turned on, MTV2 requires 30 seconds before it is fully open. h) When turned off, MTV2 requires120 seconds before it is fully closed.

PRE-HEAT

Without Electrical Heater

a) If Ti1 < 96.8ºF [or 82.4ºF depending on DIP setting], then MTV2 and AUX1 are turned on. Indoor fan

runs at 200RPM.

b) If Ti1 ≥ 100.4ºF [or 86ºF depending on DIP setting], then MTV2 and AUX1 are turned on. Indoor fan

runs at set speed.

c) If indoor coil temperature sensor is damaged, then the pre-heat time is set for 2 minutes. Indoor fan

runs at set speed.

Page 29 of 57

SK2016 HW-V-AECM-001

Pre-heat with Electrical Heater

a) MTV2 and AUX2 are turned on. b) If the indoor fan speed ≥ 300RPM, then the electrical heater will turn on.

POST-HEAT

Without Electrical Heater

a) If Ti2 ≥ 100.4ºF, then MTV2 and AUX 1 are turned off. Indoor fan continues to run at set speed. b) If 96.8F ≤ Ti2 ≤ 100.4F, then MTV2 and AUX1 are turned off. Indoor fan maintains its original state. c) If Ti2 < 96.8ºF then MTV2 and AUX1 are turned off. Indoor fan repeatedly runs for 30 seconds and then

stops for 3 minutes.

d) If the indoor coil temperature sensor is damaged, then the post-heat time is set for 3 minutes. Indoor

fan running at set speed.

With Electrical Heater

a) Indoor fan runs at 200RPM after the unit has been turned off for 20 seconds.

LOW TEMPERATURE PROTECTION OF INDOOR COIL

a) If Ti1 ≤ 35.6ºF for 2 minutes, then MTV1 and AUX2 are turned off. If indoor fan is set for low speed,

then it will run at medium speed. If it is set at medium or high speed, then it will keep running at the same speed.

b) If Ti1 ≥ 41ºF for 2 minutes, then MTV1 and AUX2 are turned on. Indoor fan runs at set speed.

OVER HEAT PROTECTION OF INDOOR COIL

a) If Ti2 ≥ 167ºF, then MTV2 and AUX1 are turned off. Indoor fan remains on and runs at high speed. b) If Ti2 < 158ºF, then MTV2 and AUX1 are turned on. Indoor fan remains on and runs at set speed. c) If the indoor coil temperature sensor is damaged, then the protection mode will be overridden and the

unit will work according to the pre-heat and post-heat set times.

DEHUMIDIFICATION MODE

a) MTV2, AUX1 and heater are always off. b) If Tr ≥ 77ºF, then MTV1 and AUX2 will be turned on for 3 minutes, and then off for 4 minutes. c) If 60.8ºF ≤ Tr < 77ºF, then MTV1 and AUX2 will be turned on for 3 minutes, and then off for 6 minutes. d) If Tr <60.8ºF, then MTV1 and AUX2 will be turned off for 4 minutes. e) At the end of the above dehumidification cycle, the system will decide the next dehumidification

control option. Indoor fan will run at low speed throughout the dehumidification process.

AUTO-MODE

a) If the current running mode is AUTO COOL mode, it will change over to AUTO HEAT mode upon satisfying

all the conditions below:

i. Ts – Tr ≥ 1.8°F (or – 7.2ºF if economy contact is activated).

ii. MTV1 has stopped ≥ 10 minutes.

b) If the current running mode is AUTO HEAT mode, it will change over to AUTO COOL mode upon satisfying

all the conditions below:

i. Tr - Ts ≥ 1.8°F (or + 7.2ºF if economy contact is activated).

ii. MTV2 has stopped ≥ 10 minutes.

Note: AUTO COOL or AUTO HEAT operations are the same as COOL or HEAT mode respectively.

Page 30 of 57

SK2016 HW-V-AECM-001

D.6. SLEEP MODE

a) The sleep mode can only be set when the unit is in cool mode or heat mode. b) If the sleep mode is activated when the unit is in cooling, the indoor fan will run at low speed and Ts will increase

2.6 ºF during 2 hours.

c) If the sleep mode is activated when the unit is in heating, the indoor fan will run at set speed and Ts will decrease

3.6 ºF during 2 hours.

d) Changing the mode of operation will cancel the sleep mode.

The cool mode sleep profile is:

The heat mode sleep profile is:

D.7. Auto Fan Speed

a) In COOL mode, the fan speed cannot change until it

has run for more than 30 seconds. Fan speed is regulated according to the profile below.

b) In HEAT mode, the fan speed cannot change until it

has run for more than 30 seconds.

High

Tr

Medium

Low

Ts+3C

Ts+2C

Ts+1C

Ts

High

Medium

Low High

Tr

Low

Medium

Ts

Ts-1C

Ts-2C

Ts-3C

Low

Medium

High

Hour

Sleep on

0.9

1.8

3.6

Sleep off

Set temperature

Ts

Ts+0.9

Ts+1.8

Ts+3.6

Hour

Sleep on

0.9

1.8

3.6

Sleep off

Set temperature

Ts

Ts-3.6

Ts-1.8

Ts-0.9

Page 31 of 57

SK2016 HW-V-AECM-001

D.8. Louver

For remote handset

Whenever the indoor fan is running, the louver can swing or stop at the desired position. Louver angle: 0~100º, opens clockwise with widest angle at 100º. Swing angle: 35~100º, opens clockwise to 68º. Below are the 4 fixed positions which can be set from wireless LCD handset.

Position

Angle

1

35º 2 57º 3 83º

4

100º

For wired wall pad

Louver angle: 0~100º, opens clockwise, with widest angle at 100º. Swing angle: 35~100º, opens clockwise to 68º. User may stop louver at any desired position between 35~100º.

D.9. Buzzer

If a command is received by the air conditioner, the master unit will respond with 2 beeps for each setting, while the slave unit will respond with 1 beep.

D.10. Auto Restart

The system uses non-volatile memory to save the present operation parameters when system is turned off or in case of system failure or cessation of power supply. When power supply resumes or the system is switched on again, the same operations as previously set will function.

Operation parameters

 when using a handset are Mode, Set Temperature, Swing, and Fan Speed  when using a wall pad parameters are Mode, Set Temperature, Swing, and Fan Speed, as well as the 7-day

ON/OFF Timer program.

D.11. Operation Of Control Panel On High-Wall Unit

D.11.1. On/Off Switch

 This is a tact switch to select COOL → HEAT → OFF operation mode.  In COOL mode, the set temperature of the system is 75.2ºF with auto fan speed and swing. There are no timer

and SLEEP modes.

 In HEAT mode, the set temperature of the system is 75.2ºF with auto fan speed and swing. There are no timer

and SLEEP modes.

 Master unit that does not use a LCD wall pad will globally broadcast.

Note: When button pressing is effective, the master unit buzzer will beep twice and the slave unit will beep once.

D.11.2. Electric Heater Safety Switch (on control PCB)

 Before the electrical heater is turned on, the EH safety switch must be closed. If this contact is opened

continuously ≥ 1 second, the heater will be turned off immediately and report an error.

 Once the contact is returned to the closed position ≥ 60 seconds, reset the error and the heater will start again.  Should the EH safety switch be opened ≥ 3 times within 60 minutes, the heater is not allowed to start anymore.  Turn off the unit to reset the fault, provided that the switch has returned to the closed position.

Page 32 of 57

SK2016 HW-V-AECM-001

D.12. LED lights

For all units

Power / Operation LED light (both green)

Unit on

Operation LED On, Power LED Off

Unit in standby

Power LED On, Operation LED Off

Page 33 of 57

SK2016 HW-V-AECM-001

D.13. LED Display and Error Description

For all units - Operation LED light (Green)

Error Description

Blink

Reason

Remedy

Electrical heater failure

Green LED blinks 1 times, stops for 3s

Only for unit with EH.

EH safety switch is open.

1. Change fan speed to high.

2. Replace the damaged EH safety

switch.

Indoor coil sensor 2 failure

Green LED blinks 2 times, stops for 3s

Ti2 sensor unplugged or damaged.

1. Check if Ti2 plug is connected or not.

2. Check if sensor’s resistance is correct

or not.

Return air sensor failure

Green LED blinks 3 times, stops for 3s

Room sensor unplugged or damaged.

1. Check if Tr plug is connected or not.

2. Check if sensor’s resistance is correct

or not.

Indoor coil sensor 1 failure

Green LED blinks 4 times, stops for 3s

Ti1 sensor unplugged or damaged.

1. Check if Ti1 plug is connected or not.

2. Check if sensor’s resistance is correct

or not.

Indoor coil low temperature protection

Green LED blinks 5 times, stops for 3s

Water temperature is lower than 37.4ºF.

Check the water temperature.

Indoor coil over heat protection

Green LED blinks 6 times, stops for 3s

Water temperature is higher than 158ºF.

Check the water temperature

EC motor failure

Green LED blinks 9 times, stops for 3s

No EC motor feedback

1. Check DIPB‐SW5 and SW6 setting.

2. Check the EC motor.

Page 34 of 57

SK2016 HW-V-AECM-001

D.14. LED Display on Master/Slave connection

The error message indicating the defect status of all slave units will be shown in LED lights on the master unit.

Master unit Protection LED light (Red)

Unit No.

Blink

Remedy

Unit 2 failure

RED LED blinks 2 times, stops for 3s

Check unit 2 communication plug and fix it

Unit 3 failure

RED LED blinks 3 times, stops for 3s

Check unit 3 communication plug and fix it

Unit 4 failure

RED LED blinks 4 times, stops for 3s

Check unit 4 communication plug and fix it

Unit 5 failure

RED LED blinks 5 times, stops for 3s

Check unit 5 communication plug and fix it

Unit 6 failure

RED LED blinks 6 times, stops for 3s

Check unit 6 communication plug and fix it

Unit 7 failure

RED LED blinks 7 times, stops for 3s

Check unit 7 communication plug and fix it

Unit 8 failure

RED LED blinks 8 times, stops for 3s

Check unit 8 communication plug and fix it

Unit 9 failure

RED LED blinks 9 times, stops for 3s

Check unit 9 communication plug and fix it

Unit 10 failure

RED LED blinks 10 times, stops for 3s

Check unit 10 communication plug and fix it

Unit 11 failure

RED LED blinks 11 times, stops for 3s

Check unit 11 communication plug and fix it

Unit 12 failure

RED LED blinks 12 times, stops for 3s

Check unit 12 communication plug and fix it

Unit 13 failure

RED LED blinks 13 times, stops for 3s

Check unit 13 communication plug and fix it

Unit 14 failure

RED LED blinks 14 times, stops for 3s

Check unit 14 communication plug and fix it

Unit 15 failure

RED LED blinks 15 times, stops for 3s

Check unit 15 communication plug and fix it

Unit 16 failure

RED LED blinks 16 times, stops for 3s

Check unit 16 communication plug and fix it

Unit 17 failure

RED LED blinks 17 times, stops for 3s

Check unit 17 communication plug and fix it

Unit 18 failure

RED LED blinks 18 times, stops for 3s

Check unit 18 communication plug and fix it

Unit 19 failure

RED LED blinks 19 times, stops for 3s

Check unit 19 communication plug and fix it

Unit 20 failure

RED LED blinks 20 times, stops for 3s

Check unit 20 communication plug and fix it

Unit 21 failure

RED LED blinks 21 times, stops for 3s

Check unit 21 communication plug and fix it

Unit 22 failure

RED LED blinks 22 times, stops for 3s

Check unit 22 communication plug and fix it

Unit 23 failure

RED LED blinks 23 times, stops for 3s

Check unit 23 communication plug and fix it

Unit 24 failure

RED LED blinks 24 times, stops for 3s

Check unit 24 communication plug and fix it

Unit 25 failure

RED LED blinks 25 times, stops for 3s

Check unit 25 communication plug and fix it

Unit 26 failure

RED LED blinks 26 times, stops for 3s

Check unit 26 communication plug and fix it

Unit 27 failure

RED LED blinks 27 times, stops for 3s

Check unit 27 communication plug and fix it

Unit 28 failure

RED LED blinks 28 times, stops for 3s

Check unit 28 communication plug and fix it

Unit 29 failure

RED LED blinks 29 times, stops for 3s

Check unit 29 communication plug and fix it

Unit 30 failure

RED LED blinks 30 times, stops for 3s

Check unit 30 communication plug and fix it

Unit 31 failure

RED LED blinks 31 times, stops for 3s

Check unit 31 communication plug and fix it

Unit 32 failure

RED LED blinks 32 times, stops for 3s

Check unit 32 communication plug and fix it

Page 35 of 57

SK2016 HW-V-AECM-001

E. Networking System

E.1. Master – Slave Network

The control PCB can be set either as a master unit or slave unit.

MASTER UNIT FUNCTION

a) The master unit sends data regarding its setting to the slave unit. b) The master unit settings are unit ON/OFF, Mode, Fan Speed, Timer, Clock, Set Temperature, Swing Function,

and Sleep Function for handset operation.

c) The master unit settings are unit ON/OFF, Mode, Fan Speed, Timer, Clock, Set Temperature, Swing Function,

and Sleep Function for wall pad operation.

SLAVE UNIT FUNCTION

a) The slave unit receives data regarding its settings from the master unit. b) The slave unit is allowed to change to a locally desired setting by local controller as long as there are no

subsequent changes to the settings of the master unit.

c) The slave units can be set individually for timer ON/OFF function by handset or wall pad. The handset cannot

override the wall pad timer and clock setting.

Page 36 of 57

SK2016 HW-V-AECM-001

E.1.1. Master – Slave Network Setup

1. Disconnect the communication plug from the control box

2. Communication plug

A, B, A, B is printed on the main PCB. When you connect the wires, please ensure connection of A to A and B to B.

3. Connection wire i. If the total length of wire is more than 1000m, please use shielded wire in order to protect the signal

transmission.

ii. Complete wire connection

First unit

Middle unit

Last unit

Page 37 of 57

SK2016 HW-V-AECM-001

iii. Wire connection check

1) After the wire connection is completed, please check that the wire colours correspond.

2) Check the wire contact by using a multimeter.

3) Check 1 and 2, 3 and 4, 5 and 6 to be sure the connections are correct.

4) If the resistance between two wire contacts is too high, please check and reconnect the wire contacts.

4. Reconnect the communication plug to the control box

First unit

Middle unit

Last unit

1st contact

2nd contact

3rd contact

4th contact

5th contact

6th contact

Page 38 of 57

SK2016 HW-V-AECM-001

Using Remote Control Handset to Set Master Control Unit:

a) Connect all the units PCBs according to the wire color and type of connector. b) Select the master unit by setting DIPA‐S1 SW6 to ON (=1) in the PCB. c) Ensure the DIPA‐S1 SW6 is set to OFF (=0) in the PCB on each slave unit. d) Switch on the units by connecting the main power supply. e) Using the handset, set the operation parameters for the master unit which will automatically send the settings to

the slave unit.

f) Master unit will beep twice confirming receipt of commands while the slave unit will beep once.

Using Wall pad to Set Master Control Unit:

a) Connect all the units’ PCBs according to the wire color and type of connector. b) Select the master unit by setting DIPA‐S1 SW6 to ON (=1) in the PCB. c) Ensure the DIPA‐S1 SW6 is set to OFF (=0) in the PCB on each slave unit. d) Provide each slave unit with an addressable code by configuring SW1 – SW5 of DIPA‐S1 according to the DIP

switch setting table.

e) Switch on the units by connecting the main power supply. f) Using the wall pad set the operation parameters for the master unit which will send the setting to the slave units

by Global‐control communication or Addressable communication methods.

g) Master unit will beep twice confirming receipt of commands while the slave unit will beep once.

MASTER-SLAVE CONTROL

The control PCB can receive data from both wireless LCD handset and wired wall pad.

Page 39 of 57

SK2016 HW-V-AECM-001

E.1.2. Master-Slave Communication Method

There are two modes for Master-slave structure.

Global Control communication The Master unit will broadcast the settings to all slave units. During normal operation, slave units can receive commands from its local wireless handset and wall pad control panel. Upon reception of master global commands, all slave unit settings will be replaced by the master settings.

Addressable communication The Master controller must be the LCD wall pad. Slave unit parameters are set as usual. Upon receiving the control commands from a master, the addressed slave unit settings will be replaced by the master settings.

DIPA-S1 address setting: ON=1, OFF=0.

DIPA-S1

SW6

DIPA-S1

SW5

DIPA-S1

SW4

DIPA-S1

SW3

DIPA-S1

SW2

DIPA-S1

SW1

Unit No.

Remark

1 0 0 0 0 0 01

Master

0 0 0 0 0 1 02

Slave 0 0 0 0 1 0

03

Slave 0 0 0 0 1 1

04

Slave 0 0 0 1 0 0

05

Slave 0 0 0 1 0 1

06

Slave 0 0 0 1 1 0

07

Slave 0 0 0 1 1 1

08

Slave 0 0 1 0 0 0

09

Slave

0 0 1 0 0 1 10

Slave 0 0 1 0 1 0

11

Slave

0 0 1 0 1 1 12

Slave 0 0 1 1 0 0

13

Slave 0 0 1 1 0 1

14

Slave 0 0 1 1 1 0

15

Slave 0 0 1 1 1 1

16

Slave 0 1 0 0 0 0

17

Slave 0 1 0 0 0 1

18

Slave

0 1 0 0 1 0 19

Slave 0 1 0 0 1 1

20

Slave

0 1 0 1 0 0 21

Slave 0 1 0 1 0 1

22

Slave 0 1 0 1 1 0

23

Slave 0 1 0 1 1 1

24

Slave 0 1 1 0 0 0

25

Slave 0 1 1 0 0 1

26

Slave 0 1 1 0 1 0

27

Slave

0 1 1 0 1 1 28

Slave 0 1 1 1 0 0

29

Slave 0 1 1 1 0 1

30

Slave

0 1 1 1 1 0 31

Slave 0 1 1 1 1 1

32

Slave

If the master unit is equipped with a wireless handset only, it can only use the Global-Control communication method. If it is equipped with a wall pad, it can use both communication methods.

Page 40 of 57

SK2016 HW-V-AECM-001

E.2. Unit Network Wiring Scheme

Wiring diagram for a master-slave network connection

Page 41 of 57

SK2016 HW-V-AECM-001

E.3. Open Modbus protocol

Transfer Mode: RTU, BAUD Rate: 9600bps, 8 data bit, 1 stop bit, None parity bit

The communications require a delay of 80ms between reading an answer and sending the next command. All temperatures are equal to reading data*10 accuracy: 0.18°F .

Supported Functions:

Function Code

Function Description

01(01H)

Read Coils

02(02H)

Read Discrete Inputs

03(03H)

Read Holding Registers

04(04H)

Read Input Registers

05(05H)

Write Single Coil

06(06H)

Write Single Register

15(0FH)

Write Multiple Coils

16(10H)

Write Multiple Registers

255(FFH)

Extended Commands which are used to test unit

Valid Error code table:

Error code

Description

Definition

01 (01H)

Invalid commands

Received commands beyond valid commands

02 (02H)

Invalid data address

Data addresses beyond valid data address

03 (03H)

Invalid data

Data beyond definition range

04 (04H)

Write data not successful

Write data did not succeed

Page 42 of 57

SK2016 HW-V-AECM-001

Coils table:

Description

Address

Type*

Remark

Unit ON/OFF

100000

R/W Sleep mode

100001

R/W Louver swing

100002

R/W

Reserved

100003

Reserved

100004

Reserved

100005

Reserved

100006

Reserved

100007

Reserved

100008

Reserved

100009

Reserved

100010

Reserved

100011

Reserved

100012

Reserved

100013

Reserved

100014

Reserved

100015

* R = read only, W = write only, R/W = read and write.

Discrete table:

Description

Address

Type*

Remark

MTV1

200000

R MTV2

200001

R AUX1

200002

R

AUX2

200003

R Condensate pump

200004

R Electrical heater

200005

R

Wired wall pad

200006

R PRO

200007

R Float switch

200008

R Reserved

200009

R EH safety switch

200010

R Unit ON/OFF status

200011

R

Testing purpose only.

* R = read only, W = write only, R/W = read and write.

Page 43 of 57

SK2016 HW-V-AECM-001

Holding Register table:

Description

Address

Type*

Remark

Mode setting

300000

R/W

Cooling mode = 01(H) Humidify mode = 02(H) Fan mode = 04(H) Heating mode = 08(H) Auto mode = 10(H)

Fan speed setting

300001

R/W

Low speed = 04(H) Medium speed = 02(H) High speed = 01(H) Auto fan speed = 07(H)

Louver swing setting

300002

R/W

Position 1 = 01(H) Position 2 = 02(H) Position 3 = 03(H) Position 4 = 04(H) Auto = 0F(H) Stop = 00(H)

Setting temperature

300003

R/W

60.8~86°F (actual*10 format)

Address setting

300004

R

Set by dip-switch, reading only

Reset

300005

W

=0x33 reset error

Week

300006

W

Calibration wired wall pad and set timer function

Hour

300007

W

Calibration wired wall pad and set timer function

Minute

300008

W

Calibration wired wall pad and set timer function

Second

300009

W

Calibration wired wall pad and set timer function

Hours in Timer on

300010

R/W

Timer ON

Minute in Timer on

300011

R/W

Timer ON

Hours in Timer off

300012

R/W

Timer OFF

Minute in Timer off

300013

R/W

Timer OFF

Icon of Timer ON or OFF

300014

R/W

BIT0 = Icon of Timer ON BIT1 = Icon of Timer OFF 1 = enable 0 = disable

Super low speed rpm

310000

R/W

200~1500

Low speed rpm

310001

R/W

200~1500

Medium speed rpm

310002

R/W

200~1500

High speed rpm

310003

R/W

200~1500

RPM setting

310004

R/W

0~2000 (used to test，0 = disable)

Temperature sampling time

310005

R/W

2~100, default:5S

Factor of auto fan speed

310006

R/W

2~150, default:20

Factor of modulating valve

310007

R/W

2~250, default:150

* R = read only, W = write only, R/W = read and write.

Page 44 of 57

SK2016 HW-V-AECM-001

Input Register table:

Description

Address

Type*

Remark

Dip switch 1 status

400000

R Dip switch 2 status

400001

R Room temperature sensor

400002

R

Ti1 temperature sensor

400003

R Ti2 temperature sensor

400004

R

Error code

400005

R

Bit0 = Room temperature sensor error Bit1 = Ti1 temperature sensor error Bit2 = Ti2 temperature sensor error Bit3 = Float switch error Bit4 = Indoor coil low temperature protection Bit5 = Indoor coil over heat protection Bit6 = Reserved Bit7 = Electrical heater failure Bit8 = Motor1 Error Bit9 = Motor2 Error Bit10 = System parameters error Bit11 = Reserved Bit12 = Reserved Bit13 = Reserved Bit14 = Reserved Bit15 = Reserved

Fan speed status

400006

R

Low = 04(H) Medium = 02(H) High = 01(H)

Mode status

400007

R

Cooling mode = 01(H) Dehumidify mode = 02(H) Fan mode = 04(H) Heating = 08(H)

Setting temperature status

400008

R

Testing only

Room temperature in wall pad status

400009

R

Room temperature in main PCB status

400010

R

Unit type

400011

R

4-pipe = 03, 2-pipe = 02 This setting is configured by dip switch

EC motor 1# RPM

400012

R EC motor 2# RPM

400013

R

* R = read only, W = write only, R/W = read and write.

Remark: The above protocol address is in Base 0.

Page 45 of 57

SK2016 HW-V-AECM-001

F. Control Specifications: Flexible Control PCB - W Type Control

Used in all High-Wall [V/P] ~W unit configurations. Ti1 = Chilled water coil temperature (10K)

F.1. Definition of Input/Output

I/O

Code

2-Pipe

Analogue Input

Chilled water Sensor

AI1

Coil sensor

Power input

R1

Lo

24 Voltage input (NO). If any speed is powered, the unit is turned on. If no speed receives power, the unit is turned off.

R 2

Med

R 3

Hi

Power input

Phase

L

Power supply: 220V/1Ph/60Hz 115V/1Ph/60Hz Neutral

N

Earth

GND

Digital input

Wired wall pad

TTL

Change EC motor rpm

Signal input AUTO SIGNAL

Auto

24V 60HZ, auto signal on, unit is turned on

0 to+5VDC (0~10VDC)

Signal

0 to +5VDC，SW1=0 (0~10VDC, SW1=1)

Motor output

EC motor

CN3

Output

Stepping motor

CN1-2

Page 46 of 57

SK2016 HW-V-AECM-001

F.2. Wiring diagram Flexible Control PCB - W Control Type

Page 47 of 57

SK2016 HW-V-AECM-001

F.3. Onboard configuration

There is 1 DIP switch set on the PCB:

DIPB (4 positions)

 SW1: configured for different modulating signal  SW2 – SW4: brushless DC fan motor configuration.

Code

State

Description

SW1 0

PCB configured for 0~5VDC modulating signal input.

1

PCB configured for 0~10VDC modulating signal input.

MODEL

SW2

SW3

SW4

Hi

Med

Low

HW-04

0 0 0

700

600

500

HW-06

0 0 1

900

700

600

HW-12

0 1 0

950

700

600

HW-15

0 1 1

1100

800

700

HW-18

1 0 0

1300

1100

900

HW-20

1 0 1

1100

900

800

HW-24

1 1 0

1200

1100 900

HW-30

1 1 1

1350

1200

900

Default RPM

1 1 1

Set by customer requirement

Page 48 of 57

SK2016 HW-V-AECM-001

F.4. Control Logics

1. Power On Setting

When any fan speed is selected, the unit is turned on. When all of the fan speed inputs (H/M/L) are off, the unit

is turned off.

2. Swing / Louver

When the unit is turned on, the louver will open to the largest angle at 100º, then move to the operating angle

at 87 º. When the unit is turned off, the louver will close.

3. Signal Input

When Auto speed is turned ON, the unit is turned on and the motor runs at 200 RPM. EC motor RPM will be

changed by the signal voltage.

F.5. LED Display

For all units

Power / Operation LED light (both green)

Unit on

Operation LED On, Power LED Off

Unit in standby

Power LED On, Operation LED Off

F.6. Error Description

For all units - Operation LED light (Green)

Item

Blink

Reason

Remedy

Indoor coil sensor 1 failure

Green LED blinks 4 times, stops for 3s

Ti1 sensor connection is unplugged or damaged.

1. Check if Ti1 plug is connected or not.

2. Check if sensor’s resistance is correct or not.

EC motor failure

Green LED blinks 9 times, stops for 3s

No EC motor feedback

1. Check if EC motor’s wires are connected.

2. Check the EC motor

Page 49 of 57

SK2016 HW-V-AECM-001

G. Users Interface

G.1. Remote Control Handset

Attention

When unit with handset is the master unit, its settings are automatically sent to the slave units; Auto Cool‐Heat operation will be applicable in 4‐ pipe system only.

“Swing” function is not applicable.

European version only uses degree C setting.

Swing It is not available.

Page 50 of 57

SK2016 HW-V-AECM-001

G.2. Wired Wall Pad

G.2.1. Wall Pad Display

Attention

a. Wall pad will recognize the main board model automatically whether it is 2‐pipe or 4‐pipe system. b. Auto Cool‐Heat operation is applicable in 4‐pipe system only. c. When the wall pad is installed the wall-pad temperature sensor automatically overrides the default return air sensor (attached near unit return air).

European version only uses degree C setting.

Page 51 of 57

SK2016 HW-V-AECM-001

G.2.2. Wall Pad Operation Guidelines

a) Clock display and setting

System has an accurate, internal, real time clock used for time indication and timer ON/OFF function. Clock

display area indicates internal time clock which can be set by the

TIME

or

TIME

buttons.

b) Day display and setting

The wall pad has a day display function which is used for day indication and timer ON/OFF function. Day display

icon indicates current day. Press

DAY

button to set day.

c) Timer ON/OFF setting

If the master unit is in global control mode and the ON/OFF timer setting is selected, the master unit will command the whole network to be ON or OFF. Otherwise the ON/OFF timer affects the local unit only. The system supports ON/OFF timer settings for each day of the week.

1) Press

TIMER

button once, and ON symbol blinking indicates ON timer programming mode. The

day display area indicates which day the timer is being set for. If there is no preset ON timer for this day,

the timer display area shows , otherwise the previous timer setting will be shown. Press

TIME

or

TIME

buttons to change the ON timer setting. Press

CANCEL

key to cancel the current ON timer setting

and the timer display area will show . Press

DAY

button to change the day the ON timer is

to be programmed for.

2) Press

TIMER

button again. and

OFF

symbol blinking indicates OFF timer programming mode. The

setting method is the same as the ON timer setting above.

3) Press

TIMER

button again to exit the ON/OFF timer setting function.

4) Should there be any ON or OFF timer settings programmed, will light up. Should there be any

unexecuted ON or OFF timer settings for the current day, its corresponding ON or

OFF

icon will light

up.

5) Hold down

CANCEL

button for 3 seconds to cancel all timer settings.

d) Timer set by master unit

1) Press

NET

button to enter into networking control mode. Unit area blinking indicates the slave unit

under control. Press

TIME

or

TIME

to select the desired slave unit. Units that are off will be skipped

automatically.

2) Press

TIMER

button once to enter into ON timer programming mode. Press

DAY

button to select the required day of the week. Master unit will then retrieve the setting from the selected slave unit and the timer display area will show “read”. The ON timer setting will be shown upon reading the data

successfully. Press

TIME

or

TIME

button to change the ON timer setting of the slave unit.

3) Press

TIMER

button again to enter into OFF timer programming mode. Press

DAY

button to select the required day of the week. Master unit will then retrieve the setting from the selected slave unit and the timer display area will show “read”. The OFF timer setting will be shown upon reading the data

successfully. Press

TIME

or

TIME

button to change the OFF timer setting of the slave unit.

Page 52 of 57

SK2016 HW-V-AECM-001

4) Upon completion of changing timer settings for the selected day, press

TIMER

button again to exit timer programming mode. The settings will then upload to the selected slave unit. The next day of the week’s settings can be done only upon completion of sending data to the slave units. (Repeat steps 1~4 if setting is required for the next day of the week).

In Global control mode:

 Pressing the master unit’s

CANCEL

button for 3 seconds will cancel all timer settings in all slave

units.

 Timer settings will be broadcast to all slave units.

e) Clock synchronization by master unit is as follows:

Press

TIME

and

TIME

buttons for 3 seconds to activate clock synchronization in all slave units. Master wall pad will

respond with a beeping sound.

f) Key lock

In order to prevent unauthorized access to the system setting, a key lock function is provided. Hold down

and for 3 seconds to activate key lock. symbol will light up. Repeat the same to exit key lock. Only

button is applicable in key lock mode.

g) Swing

Press

SWING

button to activate or deactivate swing function.

h) Sleep

Press

SLEEP

button to activate or deactivate sleep setting. The sleep function is valid in cool or heat modes only.

i) Temperature setting

Press or to enter into temperature setting mode. The temperature display area blinks indicating the current set temperature. Press the above buttons to adjust the set temperature.

j) Mode setting

Press button to change the operation mode.

k) Fan speed setting

Press

FAN

button to change the fan speed. Only low speed is available for dehumidification mode.

l) On/Off control

Press to start or stop the air conditioner.

MODE

Page 53 of 57

SK2016 HW-V-AECM-001

m) Networking Master - Slave Control (only master unit wall pad can control other units on the network)

Press

NET

button to enter into networking control mode. Unit’s display area blinking indicates the slave unit

under control. Press

TIME

or

TIME

to select the desired slave unit; Units that are off will be bypassed automatically.

Parameters that can be controlled are on/off, timer weekly program, set temperature, mode, fan speed, swing

and sleep. Parameter operation methods are the same as above. Press

NET

button again to exit networking

control mode.

Hold down

SWING

and

FRESH

buttons for 3 seconds to enter into global control mode. will light up. Repeat the same to exit global control mode. In global control mode, the settings of the master unit will be broadcast to all the slave units.

n) Unit operation parameters browsing

Hold down

CANCEL

and

FAN

buttons for 3 seconds to enter into operation parameters browsing mode. Unit

display area shows the address of the slave unit being viewed. Slave unit selection method is the same as in

networking control above. Press or to browse various parameters as follow:

Wall pad display temperature area

Wall pad display time area

C0

Return air temperature displayed

C1

Indoor coil temperature displayed

C2

DIP switch setting displayed

C3

Indoor coil 2 temperature

Press

CANCEL

button to exit.

o) Error indication

When a faulty slave unit is detected, the master unit’s display area shows the faulty unit address, the time area shows the error code and the wall pad backlight changes to the color red. Should there be multiple units having problems, addresses and error codes will be shown one after another.

Error code definition:

Error

Error code

Electrical heater faulty

E1

Indoor coil sensor 2 faulty

E2

Return air sensor faulty

E3

Indoor coil sensor 1 faulty

E4

Indoor coil low temperature protection

E5

Indoor coil over heat protection

E6

Float switch alarm

E7

Local communication error

E8

For units without master‐slave settings, the wall pad will indicate unit error codes as above.

Page 54 of 57

SK2016 HW-V-AECM-001

G.2.3. EC unit RPM setting

1. Turn OFF the unit.

2. Open wall pad’s back cover, where two DIP switches can be seen.

3. Turn the DIP switch 1 to “ON” position.

4. Wired wall pad LED will display the following:

5. To complete the RPM setting, turn the DIP switch 1 to “OFF” position. The wired wall pad display will resume its

normal appearance.

This is the motor RPM setting. Press TEMP. + / - button to increase the RPM setting by 10RPM step.

This is the speed level setting. d0 means low speed d1 means medium speed d2 means high speed Press PARAMETER + / - button to select.

Page 55 of 57

SK2016 HW-V-AECM-001

H. Sensor Resistance R-T Conversion Table

Resistance : R (77°F) = 10KΩ ± 1% Beta Constant : B (25/85) = 3977 ± 1%

T

Rmin

Rnom

Rmax

T

Rmin

Rnom

Rmax

(°F )

(KΩ)

(°F )

(KΩ)

-22

174

182.7

191.8

39.2

26.11

26.9

27.71

-20.2

163.4

171.5

179.9

41

24.85

25.59

26.34

-18.4

153.6

161.1

168.9

42.8

23.65

24.35

25.05

-16.6

144.4

151.3

158.5

44.6

22.52

23.17

23.83

-14.8

135.8

142.2

148.9

46.4

21.45

22.06

22.68

-13

127.8

133.8

140

48.2

20.44

21.01

21.59

-11.2

120.3

125.8

131.6

50

19.48

20.02

20.55

-9.4

113.3

118.4

123.8

51.8

18.58

19.7

19.58

-7.6

106.7

111.5

116.5

53.6

17.71

18.18

18.65

-5.8

100.6

105.1

109.7

55.4

16.9

17.33

17.77

-4

94.9

99.03

103.3

57.2

16.12

16.53

16.94

-2.2

89.51

93.39

97.41

59

15.39

15.77

16.16

-0.4

84.5

88.11

91.85

60.8

14.69

15.05

15.41

1.4

79.8

83.17

86.64

62.6

14.03

14.37

14.7

3.2

75.39

78.53

81.76

64.4

13.41

13.72

14.03

5

71.26

74.18

77.19

66.2

12.81

13.1

13.4

6.8

67.37

70.1

72.9

68

12.24

12.52

12.79

8.6

63.73

66.26

68.88

69.8

11.7

11.96

12.22

10.4

60.3

62.67

65.1

71.6

11.19

11.43

11.67

12.2

57.08

59.28

61.55

73.4

10.71

10.93

11.15

14

54.05

56.1

58.22

75.2

10.24

10.45

10.66

15.8

51.19

53.12

55.08

77

9.8

10

10.2

17.6

48.51

50.3

52.14

78.8

9.374

9.57

9.765

19.4

45.98

47.66

49.37

80.6

8.969

9.16

9.351

21.2

43.61

45.17

46.77

82.4

8.584

8.77

8.957

23

41.36

42.82

44.31

84.2

8.218

8.4

8.582

24.8

39.25

40.61

42

86

7.869

8.047

8.225

26.6

37.26

38.53

39.83

87.8

7.537

7.71

7.885

28.4

35.38

36.56

37.78

89.6

7.221

7.39

7.56

30.2

33.6

34.71

35.85

91.4

6.92

7.085

7.251

32

31.93

32.97

3402

93.2

6.633

6.794

6.956

33.8

30.35

31.32

32.3

95

6.36

6.517

6.675

35.6

28.85

29.76

30.68

96.8

6.099

6.252

6.407

37.4

27.44

28.29

29.15

98.6

5.85

6

6.151

Page 56 of 57

SK2016 HW-V-AECM-001

Resistance : R (77°F) = 10KΩ ± 1% Beta Constant : B (25/85) = 3977 ± 1%

T

Rmin

Rnom

Rmax

T

Rmin

Rnom

Rmax

(°F )

(KΩ)

(°F )

(KΩ)

100.4

5.614

5.759

5.907

167

1.417

1.474

1.532

102.2

5.387

5.53

5.673

168.8

1.37

1.426

1.482

104

5.172

5.31

5.451

170.6

1.326

1.379

1.434

105.8

4.966

5.101

5.238

172.4

1.282

1.335

1.389

107.6

4.769

4.901

5.034

174.2

1.241

1.292

1.344

109.4

4.582

4.71

4.84

176

1.201

1.25

1.302

111.2

4.402

4.527

4.654

177.8

1.162

1.211

1.261

113

4.231

4.353

4.477

179.6

1.125

1.172

1.221

114.8

4.067

4.186

4.307

181.4

1.089

1.135

1.183

116.6

3.911

4.027

4.144

183.2

1.055

1.1

1.146

118.4

3.761

3.874

3.989

185

1.021

1.065

1.111

120.2

3.618

3.728

3.84

186.8

0.9891

1.032

1.077

122

3.481

3.588

3.697

188.6

0.9582

1

1.044

123.8

3.35

3.454

3.561

190.4

0.9284

0.9697

1.012

125.6

3.225

3.326

3.43

192.2

0.8998

0.9401

0.9818

127.4

3.105

3.204

3.305

194

0.8721

0.9115

0.9522

129.2

2.99

3.086

3.185

195.8

0.8455

0.8839

0.9237

131

2.88

2.974

3.07

197.6

0.8198

0.8573

0.8961

132.8

2.774

2.866

2.959

199.4

0.795

0.8316

0.8696

134.6

2.673

2.762

2.854

201.2

0.7711

0.8069

0.8439

136.4

2.576

2.663

2.752

203

0.748

0.783

0.8192

138.2

2.483

2.568

2.655

204.8

0.7258

0.7599

0.7953

140

2.394

2.477

2.562

206.6

0.7043

0.7376

0.7722

141.8

2.309

2.39

2.472

208.4

0.6836

0.7161

0.7499

143.6

2.227

2.306

2.386

210.2

0.6635

0.6953

0.7283

145.4

2.149

2.225

2.304

212

0.6442

0.6752

0.7075

147.2

2.073

2.148

2.224

213.8

0.6255

0.6558

0.6874

149

2.001

2.074

2.148

215.6

0.6075

0.6371

0.6679

150.8

1.931

2.002

2.075

217.4

0.59

0.619

0.6491

152.6

1.865

1.934

2.005

219.2

0.5732

0.6015

0.631

154.4

1.801

1.868

1.937

221

0.5569

0.5846

0.6134

156.2

1.739

1.805

1.872

158

1.68

1.744

1.81

159.8

1.623

1.686

1.75

161.6

1.569

1.63

1.692

163.4

1.516

1.576

1.637

165.2

1.466

1.524

1.583

Page 57 of 57

SK2016 HW-V-AECM-001

I. Troubleshooting Guide

Space Pak ECOELEGANT SERIES, HW~ECM SERIES Installation, Operation And Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual