Soyal Control Systems, AR-829, E-V5 User Manual

SOYAL
Copyright by SOYAL Technology Co., Ltd.. All rights reserved.
ACCESS CONTROL SYSTEM
Contents
1
Products
Installation
2
User Guide
3
®
3
Terminal Cables
P4 P5 P6
AR-829E-V5
P1 P2 P3
V120508
4
Tools
5
Optional
AR-721RB
AR-821RB
Digital Relay
#
*
4
Notice
1.Tubing:
2.Wire selection:
3.Power supply:
Connector Table
The communication wires and power line should NOT be bound in the same conduit or tubing.
Use AWG 22-24 Shielded Twist Pair to avoid star wiring ,CAT 5 cable for TCP/IP connection Don’t equip reader and lock with the same power supply. The power for reader may be unstable when the lock is activating, that may make the
reader malfunction. The standard installation: Door relay and lock use the same power supply, and reader use independent power supply.
1
2
Use a screwdriver to screw the mounting plate to the wall.
Pull cables ends through the access hole in the mounting plate.
Attach AR-829E to the mounting plate and install screws (supplied) into the
holes at the bottom with the allen key (supplied).
Apply power. LED (green) will light up.
Cable:
P3
Wire Application Wire Color Description
P3
P2
P4
8
2 1
7 6
P6
5 4
4
3
3
2
2
1
1
2
1
P1
TCP/IP Output 3
P5
321
7 6 5 4 3 2 1
876 543
P7
6 5 4 3 2 1
1 --- --- 2 --- ---
Orange White 4 Orange 5 Green White 6 Green 7 --- ---
Net - TX+ Net - TX- Net - RX+ Net - RX-
Cable:
P1
Wire Application Wire Color Description
Lock Relay 1 Blue White (N.O.)DC24V1Amp
2
Purple White
(N.C.)DC24V1Amp Lock Relay COM 3 White (COM)DC24V1Amp Door Contact 4 Orange Negative Trigger Input Exit Switch 5 Purple Negative Trigger Input Alarm Relay 6 Gray DC24V1Amp Power 7 Thick Red DC 12V
8 Thick Black DC 0V
Cable:
P2
Wire Application Wire Color Description
Beeper 1 Pink Beeper Output
LED
Door Output 4 Blue White
Wiegand
WG Door
Contact
2 Yellow Red LED Output 3 Brown Green LED Output
Transistor Output Max. 12V/100mA
(Open Collector Active Low)
5 Thin Green Wiegand DAT: 0 Input 6 Thin Blue Wiegand DAT: 1 Input 7 Orange Negative Trigger Input
5V/100mA, Low
5V/20mA, Max
WG Exit Switch 8 Purple Negative Trigger Input
5V/20mA, Max
Cable: P4
Wire Application Wire Color Description
RS-485 for Lift Controller
Cable:
P5
Wire Application Wire Color Description
Anti-Tamper Switch 1 Red N.C.
Cable:
P6
Wire Application Wire Color Description
Power 1 Red DC 12V Security trigger signal Arming 3 Red White Arming Output Duress 4 Yellow White Duress Output
Cable: P7
Optional:(Request to purchase AR-725L485 additionally)
Wire Application Wire Color Description
TTL Port 1 Black DC 0V
1 Thick Green RS-485(B-) 2 Thick Blue RS-485(A+)
2 Orange COM 3 Yellow N.O.
Output
2 Purple Security trigger signal Output
2 Yellow 3 White 4 Orange
TX TE
RX 5 Red DC 5V 6 --- ---
PW R
ER R
AR M
OK
PR E
V
5
SE RI ES
12/07
Ready . . .
14 : 49 : 04
WED
Duty : 0
PW R
ER R
AR M
OK
PR E
V
5
SE RI ES
12
07
Ready . . .
14 : 49 : 04
WED
Duty : 0
Copyright by SOYAL Technology Co., Ltd.. All rights reserved.
Front Panel & Indicator
LCD Access Controller
V120508
Power
Alarm
Alarm
(Green)
(Red)
(Green)
(Green)
OK Error
(Red)
In processing
(Green)
1. System will automatically exit from Programming Mode when inactivating for 30 seconds.
2. LED status indicates controllers mode and status. OK (green) – blinking constantly when operates in Programming Mode
or ashing an existed card in card learn mode, it comes 2 beeps warning and LCD panel displays “Same Card: user address / card number” Error (red) invalid card with 2 beeps warning and LCD panel displays “Card Number Err!” or in anti-pass-back mode, when violates the access, it comes one beep warning and LCD panel displays “Anti-pass Error!”
Arming (green) – arming on status Alarm (red) – any abnormal condition occurs
3. Keypad will be locked up 30 sec. when constantly entering incorrect pin code or master code.
4. Maximum error in[ut of pin code and master code can be changed via the software 701Server (default: 5 times)
Networking : / and interactively ash between the Month and DAY. [e.g.] 12/07←→12 07
Stand-alone : No ashing [e.g.] 12/07
(←Reference to picture)
Wiring Diagram
Connect to Electric Bolt
Connect to Magnet Lock
Electric Bolt
Exit Switch
E
12V
GND
12V
GND
POWER
12VDC
Magnet Lock
P1
1
N.O.
2 3
COM
4 5
PB
Controller
12V
GND
POWER
12VDC
6 7 8
12V
GND
N.O.
GND
EXIT
RTE
Controller
POWER
12VDC
Connect to Electric Strike Connect to Door Contact
Controller
Electric Strike
POWER
12VDC
N.O.
COM
PB
12V
GND
12V
GND
P1
1 2 3 4 5 6 7 8
12V
GND
12V
GND
N.O. GND
POWER
12VDC
EXIT
RTE
POWER
12VDC
Door Contact
ALM
12V
Controller
GND
POWER
12VDC
N.C.
COM
PB
12V
GND
P1
1 2 3 4 5 6 7 8
P1
12V
GND
12V
GND
12V
GND
1 2 3 4 5 6 7 8
12V
GND
12V
GND
12V
GND
POWER
12VDC
N.O. GND
EXIT
RTE
Alarm
N.C. N.O.
COM
CTL 12V
Relay Outpot Module
N.C.
Door Contact
SOYAL
Copyright by SOYAL Technology Co., Ltd.. All rights reserved.
ACCESS CONTROL SYSTEM
®
AR-829E-V5
V120508
Strengthen security with AR-721RB
12V
GND
Electric Bolt
1 2
4
1 2 3
Controller
P6
DDR
12V
POWER
12VDC
12V
GND
3 4
P1
5 6 7 8
12V GND
12V
GND
POWER
N.C. N.O.
COM
CTL 12V
GND
PB
AR-721RB
N.O.
12VDC
EXIT
RTE
Connect to Reader
12V GND Exit Switch
Electric Bolt
Reader
E
N.C. N.O. COM
CTL 12V
BZ RLED GLED WG 0 WG 1
12V
GND
If any re emergency, the people can escape by press a switch to open all doors
Electric Strike
N.O.
COM
PB
12V
GND
P1
12V GND
1 2 3 4 5 6 7 8
Transistor IN4007
POWER
12VDC
RTE
EXIT
Magnet Lock
N.C.
COM
PB
12V
GND
P1
12V GND
1 2 3 4 5 6 7 8
POWER
12VDC
EXIT EXIT
Electric Bolt
P2
1 2 3 4 5 6 7 8
P1
N.O.
COM
PB
12V
GND
POWER
12VDC
BZ RLED GLED Door Output WG 0 WG 1
WG-DS WG-PB
12V
GND
Controller
12V GND
E
1 2 3 4 5 6 7 8
P1
1 2 3 4 5 6 7 8
Door Contact
N.C.
EXIT
RTE
POWER
12VDC
POWER
12VDC
RTERTE
Transistor IN4007
Fire Emergency
Adding and Deleting Tag
User capacity: 16384 (00000~16383)
Adding Tag by Tag ID
Access programming mode
1 1
Add/Delete
Add -> Card ID
Input 5 -digit user address
Adding Tag by RF Learn Function
Access programming mode
Input Tag Units(pcs)
If a batch of tags are Sequential, input Tag Units(pcs) in the quantity of the tags and present the tag with
1 2
Add/Delete
Close Tag into RF Area
Add -> RF-Learn
Input 5 -digit user address
the lowest number to the controller.
Suspend User Address
Access programming mode
1 3
Add/Delete
Suspend -> Addr
Input Start address
Suspend Tag by Tag ID
Access programming mode
1 4
Add/Delete
Suspend -> ID #
Input Site Code
Input Card Code
Recover User Address
Access programming mode
1 7
Add/Delete
Delete -> Addr
Input Start address
Input End address
Recover Tag by Tag ID
Access programming mode
1 8
Add/Delete
Delete -> ID #
Input Site Code
Input Card Code
Deleteing User Address
Access programming mode
1 5
Add/Delete
Delete -> Addr
Input Start address
Input End address
Deleteing Tag by Tag ID
Access programming mode
1 6
Add/Delete
Delete -> ID #
Input Site Code
Input Card Code
Setting up the access mode
Access programming mode
2 2
User Setting
Access Mode
Input User Address 0: Invalid; 1: Card ; 2: Card or PIN; 3: Card & PIN
Input Site Code
Tag Information
Input End address
Input Card Code
CARD COD E
SITE COD E
CARD COD E
SITE COD E
LCD Access Controller
Copyright by SOYAL Technology Co., Ltd.. All rights reserved.
Programming
A. Keyboard Lock/ Unlock
Lock/ Unlock
Press and , and at the same time to lock keyboard. Press again to unlock.
B. Entering and Exiting Programming Mode
Entering
Input 123456 or PPPPPP [e.g.] The Default Value= 123456. If already changed the Master Code= 876112, input
P.S.If entering no instruction within 30 sec., it will automatically leave the programming mode.
Exiting
Press the repeatedly
Changing the Master Code
Access programming mode
6
Quit or Quit and Arming (Please refer to alarm / arming setting)
7
5 2
Tool s
Master Code
Input the 6-digit new master code
C. Initial setup
Language Setting
Access programming mode
Node ID of Reader Setting
Access programming mode
WG1 Door Number : 0~255 Show UID (0 =No,1=WG,2=ABA,3=HEX) Enable DHCP(0:No,1:En,2=Exit) Succeeded
5 1 0
Tool s
3 1
Parameters[1]
Language
EN Succeeded Initial system...
Node ID
Input New Node ID : 1~254 (default value:001) Main Door Number : 0~255
87 6112
Access programming mode
Succeeded
V120508
D. PIN Code
Access programming mode Or via 701Client set it on Users screen
2
User Setting
1
Password
Input 5 -digit user address
Input 4 -digit PIN (0001~9999)
Succeeded
E. Arming Password
Access programming mode Or via 701Server and set it on AR-829E screen
3
Parameters[1]
8
Arming PWD
Input 4 -digit PIN (0001~9999; Default: 1234)
Succeeded
F. Arming Delay Time
Access programming mode
Armed pulse out- put time. (10ms) ,Range000~255
3
Par ameters[1]
7
ArmingDelayTm
Succeeded
Enter armed sta. Delay time(Sec) ,Range:000~255
G. Duress Code
Access programming mode
Or via 701Server to set it on AR-829E-V5 screen
Duress Code is only available in networking mode. It will substitute a personal pin code and send the message of Duress to computer as a
warning signal.
4 7
Parameters[2]
Duress Code
4 sets (select one)
Input 4 -digit PIN (0001~9999)
Succeeded
H. Terminal Port
Access programming mode
(default value:9600)
Succeeded
Tool s
5 4
Terminal Port
0:Lift ; 1:Host ; 2:LED ; 3:PRN (default value:1) Baud Selection
I. Setting up the alarm / arming
Conditions:
1. Arming enabled
2.Alarm system connected
Application:
1. Door open too long: Door is open longer than door relay time plus door close time.
2. Force open (Opened without a valid user card): Access by force or illegal procedure.
3. Door position abnormal: When power is off and then on, reader on arming before power off.
Enable/Disable the arming status:
Standby Mode
Card only Card or PIN Card and PIN
Open the door
Present the tag to reader
4 digits arming PWD
Access Programming mode
Enable: Access programming mode
Input
No open the door
Input 4 digits arming PWD
Present the tag to reader
7
Quit & Arming
Input user address
digits individual PWD
Input 4 digits arming PWD
Disable: Access programming mode
Input 4
Present the tag to reader
4 digits individual PWD
Input 4 digits arming PWD
6
Quit
Input
®
Copyright by SOYAL Technology Co., Ltd.. All rights reserved.
AR-829E-V5
SOYAL
ACCESS CONTROL SYSTEM
J. Anti-pass-back
While connect with AR-721U, AR-737H/U(WG mode) and AR-661U for anti-pass-back function, the access mode needs to be "Card" only.
Device enable
Access programming mode
Card user enable
Access programming mode
address
must select [1: Yes]
K. Lift control
[e.g.] Connect with AR- 401RO16B to control which oors the user will be able to access. (BAUD9600)
Setting Lift control
Access programming mode
Access programming mode
(need to use 725L485)
Set
Floor/ Stop
1
3
2
4
0
1
2
3
4
17
33
49
0
19
18
0
0
35
34
0
0
51
50
0
0
5
0
0
0
20
21
0
0
0
36
37
0
0
0
52
53
0
0
0
4 6
Parameters[2]
1 9
Add/ Delete
5 4
Tool s
5 5
Tool s
9
7
8
0
0
1
25
24
0
0
0
41
40
0
0
0
57
56
0
0
0
22
38
54
6 0
23
0
39
0
55
0
10
0
26
0
42
0
58
0
11
27
43
59
Anti-pass-back
Antipass Group
Terminal Port
Terminal Port
12
13
28
44
60
14
0
0
29
30
0
0
45
46
0
0
61
62
0
0
0
0
0
0
0
1
0
0
0
0
15
0
31
0
47
0
63
0
master controller select [1: Yes] WG select [1: Yes]
Input 5 -digit star ting user address
Lift Controller Baud Selection 09600
Lift Controller
16
1
32
0
48
0
64
0
Input 5 -digit ending user
V120508
Single oor
Access programming mode
Input 5 -digit user address
Multi oors
Access programming mode
multi oors number [0:disable, 1: enable]
[e.g.] Set NO. 114, can use it with the 8 F and 16F:
Access programming mode
2 4
User Setting
Input single oor number: 1~64
2
User Setting
2
User Setting
L. Alarm Clock (for Factory)
Access programming mode
(Seconds as the bell time, Range:1~255)
Hardware installation
Music Box
Horn
5 9
Board
Tool s
Mike device
Mike device
Single Floor
5
Multi Floor
5
Daily Alarm
Set Weekday (0:disable, 1: enable) Succeeded
DC 12V Relay Board
Input 5 -digit user address
Multi Floor
Set (00~15) Set Start Tm (24 Hours) ; Set Effect Sec.
POWER
12VDC
Mike's sound wire
Mike's sound wire
114
12V
CTL COM N.O. N.C.
1
M1
M2
GND
Music Box
Output to M1 and M2
Select range: 1 or 2 or 3 or 4
0000000100000001
P1
1 2 3 4 5 6
ALM
7
12V
8
GND
Controller
Input 16 digits
M. OpenZone
Access programming mode
Open Door Imm. During Open Zone (0 :No ,1:Yes)
Open Zone (0:No,1:Yes)
3 2
Parameters[1]
Succeeded
OnOff OpenZone
WG1 Port Auto Open Zone (0:disable,1:enable) Open Door Imm. During
N. Open TimeZone
Access programming mode
WG Port (0:disable, 1: enable) Weekday (0:disable, 1: enable)
5 6
Tool s
Open TimeZone
Main Controller Auto Open Zone (0:disable,1:enable)
Set (00~15) Time (24 Hours) ; Main Port (0:disable, 1: enable) ;
succeeded
LCD Access Controller
Copyright by SOYAL Technology Co., Ltd.. All rights reserved.
Firmware Upgrade
Get the upgrade software from SOYAL or our distributor and run “UdpUpdater” software
Execute the software The software is within SOYAL CD or Login the SOYAL web to downloads
V120508
2
1
5
Update the rmware
[Please login the SOYAL web to download the new ISP Firmware.]
1. Input the Target Address and Port
2. [Load F/W] open the documents that have the new ISP Firmware
3. Click the new ISP Firmware and [Open] it
4. Click [Update F/W] to start the rmware update
5. Till the screen shown [Firmware Update is Complete]
4
3
Restoring Factory Settings
Reset all device parameters and user card data
Reset all device parameters and user card data:
Access programming mode
1 : User Setting ; 2 : System & User
Reset IP Setting:
When the device's power is on, press theRESETbutton the main board untill the ERR (Red) LED of
screen lights up. (Reference to picture)
After operation as above, you will hear the long reminder sound,and wait until the
sound disappear then reset the power of the controller,the device will restore factory setting.
Manu Tree
1. Add/ Delete
1. Add > Card ID
2. Add > RF Learn
3. Suspend > Address
4. Suspend > ID #
5. Delete > Address
6. Delete > ID #
7. Recover > Address
8. Recover > ID #
9. Antipass Group
2. User Setting
1. Password
2. Access Mode
3. Extend Options
4. Single Floor
5. Multi Floor
Parameters2
Factory Reset 0 : System Param ;
94
3. Parameters[1]
1. Node ID
2. OnOff OpenZone
3. Door Relay Tm
4. Door Close Tm
5. Alarm Relay Tm
6. Alarm Delay Tm
7. Arming Delay Tm
8. Arming PWD
4. Parameters[2]
1. Auto Relock
2. Egress(R.T.E)
3. Miscellaneous
4. Force Open
5. Close & Stop
6. Anti-pass-back
7. Duress Code
8. Password Mode
9. Factory Reset
5. Tools
1. Language
2. Master Code
3. Master Range
4. Terminal Port
5. Ext.Comm Port
6. Open Time Zone
7. Informations
8. Clock Setting
9. Daily Alarm
6. Quit
7. Quit & Arming
®
Copyright by SOYAL Technology Co., Ltd.. All rights reserved.
SOYAL
ACCESS CONTROL SYSTEM
IP Setting
Open your Web Browser and input factory default IP
address: http://192.168.1.127
If the IP address of AR-829E-V5 has changed We must enter the new IP address.
Page menu
Monitor the on-line computer
IP Setting
Change the Log-in information
AR-829E-V5
V120508
Current State
Online Status is able to monitor and
show which computer is linking on Ethernet Module
Show which computer is li nking on Ethernet Module.
Current IP address of the AR-829E-V5
Log-in User Password
When you choose the "Networking Setting" or " User Password" at rst.
Log-in window will pop out and please input
At the Factory Default
User name: admin
Password: No as default value,so please just press OKto log-in
Networking Setting
You will nd initial IP Address 192.168.1.127 and check
MAC Address is the same as sticker on Ethernet Module
device. Please revise IP address you want, and then click
Updatebutton. After updating the IP, please re-connect
the Web Browser by new IP address.
admin
User Password
Change the log-in password to lock the IP setting of
Ethernet Module.
The password composes of 10 characters at most, it can be
either A~Z or 0~9.
Neworking
DI
DO
DI
WG
Exit
Door Open
Relay output
Entrance
Diagram of
Basic
application
of single
door
AR-721U
Push Button
Electric Lock
Door Sensor
AR-725H-M
Alarm
TCP/IP
TCP/IP
RS-232
RS-232
RS-485
TTL
WGUSB
DO
DO
A
R-727H
USB
WG
WG WG WG WG
WG WG
WG1 WG2
TTL
TTL TTL
RS-485RS-485
RS-485
RS-485
USBGSM
TCP/IPTCP/IP TCP/IP TCP/IP TCP/IP
LED Display
HUB
TTL
RS-485
RS-485 (CH1)
(Up to 8 nodes)
RS-485
Up to 254 nodes
RS-485
Up to 254 nodes
RS-485
Up to 254 nodes
RS-485
Up to 254 nodes
RS-485 (CH2)
(Up to 8 nodes)
GSM MODEM
GSM MODEM
AR-716Ei
TCP/IP
AR-716E
AR-725H-M
AR-725H-M
AR-331H AR-321H
AR-725E-M/V2
AR-321L485 AR-321L485
AR-321DAX1
AR-737U
AR-723H
AR-661U AR-725U-M AR-737UAR-721U
AR-321W
AR-401Ei
AR-401DI16
AR-401RO16
AR-401E
AR-401DI16
AR-401RO16
Programmer
AR-737P
AR-737H
AR-727CM AR-701CM AR-321CM
AR-821EVi/V5
AR-821EF/V5
AR-829E/V5AR-727H
AR-727H
AR-327H AR-721H
AR-721K
AR-721H
AR-725K-MAR-725U-M
AR-323D
AR-PB-321
AR-PB-323
INTERNET
AR-881EFAR-881EV
System Diagram
1.Software for
Security Access
or Attendance
2.SOR Applications
3.Software for
Networking or
device setting
AR-401E
Comm View
ISP Tools
Mifare Key
SOR Tools
701 Client
701 Server VisualProx
NODE 737
NET 727
(AR-727i V1) (AR-727i V2)
Web
4.Firmware
Update
5.Development,
Monitoring
Software
6.Programmable
Software
Computer-Aided
Software
Computer
Interface
Application Software
Converter
(RS-485)
Access Controller
(Ethernet)
Access Controller
Converter
(Wiegand)
Access Reader
(Ethernet)
Multi-Door
Networking
Controller
(RS-485)
Multi-Door
Networking
Controller
Room control
systems
Programmable
Controller/
Lift Controller
AR-401RO16B
Elevator
(Lift Control)
16-Levels Lift
Controller
AR-725U-M
Copyright by SOYAL Technology Co., Ltd.. All rights reserved.
LCD Access Controller
V120508
Loading...