Soyal AR-331, AR-331H, AR-321, AR-721H, AR-725 User Manual

...

Download

SOYAL

ACCESS CONTROL SYSTEM

Contents

AR-321 (H): Touch-panel Metal Housing

Product

User Guide

AR-721(H) / AR-725 (H) / AR-757 (H)

AR-321 (H) / AR-331 (H) /

Terminal Cables

Tools

Water proof Strip

V140707

AR-331 (H): Touch-panel Metal Housing / AR-331 (H-S): Metal Housing

Product

WG keyboard

AR-331 (H) AR-331 (H-S)

[Optional]

Optional

AR-721RB Digital Relay

AR-821RB Original Relay

User Guide

AR-721 (H)

Product

User Guide

Terminal Cables

AR-725 (H): Illuminated Touch-panel

AR-725 (H-M)

Products

User Guide

AR-725 (H)

Products

User Guide

d x2

Additional external relay must be purchased.

※

Terminal Cables

Tools

c x2

g x1 h x1

Tools

f x2

Tools

c x2

e x1

Tools

A1.

AR-725 (X)

Products

A2. A3.

AR-757 (H)

Product

Parts Description

Button Head Pozidriv Tapping Screw: M3x10

e. f.

Security Torx Screw: M3.5x15

C. H.G. D.

User Guide

b. c. d.

Button Head Pozidriv Slotting Screw: 2.5x10

Flat Head Hex Socket Screw: M3x8

Terminal Cables

Flat Head Cap Philips Tapping Screw: 4x19.1

g. h.

Security Torx Screw: M3x10 Security Torx Wrenches

Tools

a x2

b x2

c x2

Tools

Flat Head Cap Philips Tapping Screw: 4x38

f x2

e x1

f x2

Installation

AR-321 (H)

AR-331 (H) / AR-331 (H-S)

AR-721 (H)

Access Controller

Touch-panel Metal Housing / Illuminated Touch-panel

Pull the cables from the square hole of the mounting plate.

Use a screwdriver to screw the mounting plate onto the wall.

Attach the water proof strip to the body, then connect the terminal cables to the body and attach the body to the mounting plate.

Use the Allen key and screws (accessories supplied) to assemble the body onto the mounting plate.

Turn on the power, and LED will light and beep will sound.

Remove the rubber plug. To cut tamper-resistant column and make it fit the appropriate

height for actual installation. First, take off the metal casing then screw the controller on the wall. Second, put the metal casing back and lock it with security screw. Finally, put the rubber plug into the hole.

Pull the cables from the square hole of the mounting plate.

Use a screwdriver to screw the base onto the wall.

Connect the terminal cables to the body and attach the body to the mounting plate.

Assemble the covers with the Allen key and screws (accessories supplied).

Turn on the power and LED will light and beep will sound.

Turn on the power, and LED will light and beep will sound.

V140707

AR-725 (H)

AR-725 (H-M)

AR-725 (H)

AR-725 (X)

A1.

Pull the cables from the square access hole of the mounting plate C.

Use a screwdriver to screw the metal plate C onto the wall.

Take off the plastic mounting plate B from the body A, and pull the cables through the access hole of C and B, then connect to the body A.

Assemble plate B with the body A, and embed the water proof strip D

onto the plastic side frame.

Assemble the body A onto the mounting plate C with the Allen key and screws (accessories supplied).

Turn on the power and LED will light and beep will sound.

A1.

Use a screwdriver to screw the base F onto the wall.

Attach the water proof gasket to the body A1, and pull the cables from the square hole of the base F, and connect to the body A1.

Assemble the body A1 with the base F.

Screw A1 and F tight with the Allen key and screws (accessories supplied).

Turn on the power and LED will light and beep will sound.

Put on G, and attach A1 onto the plastic plate A3, and screw it with the Allen key and screws (accessories supplied).

Put the ring O on the metal frame, and put them together onto the reader A1+A3, and screw them and buckle up the 4 buckles on the back.

Embed the water proof strip D onto the frame side of the base.

Following by the install process of AR-725 (H-M)

A3.

A2.

A1.+A3.

AR-757 (H)

Pull the cables from the square hole of the mounting plate.

Use a screwdriver to screw the base onto the wall.

Embed the water proof strip 3 onto the frame side of the base.

Connect the terminal cables to the body and attach the body to the mounting plate.

Assemble the covers with the Allen key and screws (accessories supplied).

Turn on the power and LED will light and beep will sound.

SOYAL

ACCESS CONTROL SYSTEM

Notice

1.Tubing:

2.Wire selection:

3.Power supply:

Connector Table

AR- 321H

AR-321 (H)

125kHz

13.56MHz

AR-331 (H) / AR-331 (H-S)

125kHz

13.56MHz

The communication wires and power line should NOT be bound in the same conduit or tubing.

Use AWG 22-24 Shielded Twist Pair to avoid star wiring.

Don’t equip controller and lock with the same power supply. The power for controller may be unstable when the lock is activating, that may make the controller malfunction.

The standard installation: Door relay and lock use the same power supply, and controller use independent power supply.

10 98765432

AR-321 (H) / AR-331 (H) /

AR-721(H) / AR-725 (H) / AR-757 (H)

P1Cable :

Wire Application

Lock Relay

Common-COM-Point Door contact Exit Switch Alarm Relay Power

P2Cable :

Wire Application

Wiegand

Beeper

LED

Blue White

Purple White

2 3 4 5 6

Thick Red

Thick Black

Thin Blue

Thin Green 3 4 5

Color

White

Orange

Purple

Gray

Color

Pink Brown Yellow

Description

(N.O.) DC24V1Amp (N.C.) DC24V1Amp (COM) DC24V1Amp Negative Trigger Input Negative Trigger Input Low output; Max 12V/100mA (Open Collector) DC Power 12V DC Power 0V

Description

Wiegand DAT:1 Input Wiegand DAT:0 Input Beeper Output 5V/100mA, Low LED Green Output 5V/20mA, Max LED Red Output 5V/20mA, Max

V140707

AR-721 (H)

125kHz

13.56MHz

AR-725 (H)

125kHz

13.56MHz

AR-757 (H)

125kHz 13.56MHz

Connectors Comparison

AR-321 (H) AR-331 (H) AR-721 (H) AR-725 (H) AR-757 (H)

P1 P2 P3 P4 ( P7 P8 P1 P2 P3 P4 ( P1 P2 P3 P4 ( P1 P2 P3 P4 P6

P3Cable :

Wire Application

Networking Module

P4Cable :

Wire Application

Tamper Switch

P5Cable :

Wire Application

Optional

)P5

)P5 )P5

3-PIN Connector

P6Cable :

Wire Application

Doorbell Arming Duress LED indicator

P7Cable :

Wire Application

Power

Exit Switch Networking Module

Lock Relay

Networking Module

Tamper Switch

Alarm Relay Door contact

LED

Beeper

Wiegand

Color

Thick Green

Thick Blue

(Contact Rating: 1A 125VAC/24VDC)

Color

Red

Orange

Yellow

(Optional)

Color

Black

White

Purple

Color

Brown White

Red White

Yellow White

Green White

(Directly connected at the Access controller)

Color

Thick Black

Thick Red

Purple

Thick Green

White

Thick Blue

Yellow White

Orange White

Gray

Orange

Brown

Yellow

12 13 14 15

Pink

Thin Blue

Thin Green

Description

RS-485(B-) RS-485(A+)

Description

N.C. COM N.O.

Description

GND. Duress Arming/ Security trigger signal

Description

BE Output AR Output/ Security trigger signal Output DU Output/ TTL out Hi input/ Green light brighten

Description

DC Power 0V DC Power 12V Negative Trigger Input RS-485(B-) Low output; Max 12V/100mA (Open Collector)/ Security trigger signal Output RS-485(A+) N.O. COM Low output; Max 12V/100mA (Open Collector) Negative Trigger Input LED Green Negative Output 5V/20mA, Max LED Red Negative Output 5V/20mA, Max Beeper Negative Output 5V/100mA, Low Wiegand DAT:1 Input Wiegand DAT:0 Input

After S/N: 0706-XXXXXX

※

Touch-panel Metal Housing / Illuminated Touch-panel

Wiring Diagram

Connect to Magnetic Lock or Electric Bolt

12V

GND

Electric BoltorMagnetic Lock

Access Controller

Connect to Electric Strike

12V

POWER

GND

12VDC

Electric Strike

12V

GND

12V

GND

V140707

POWER

12VDC

ALM

12V

GND

Host

CH1

CH2

N.O.

COM

12V

GND

B-

A+

1 2 3 4 5

6 7 8

12V GND

12V

GND

1 2 3 4 5 6 7 8

12V

GND

A+

B-

A+

B-

A+

B-

A+

1 2

N.C.

COM

3 4 5

Controller

GND

POWER

12VDC

12V

6 7 8

12V GND

N.O.

EXIT

Request To Exit

Connect to Reader

Controller Reader

WG 1

WG 0

GLED

RLED

1 2 3 4 5 6

12V

GND

WG 1 WG 0

BZ GLED RLED

12V

GND

POWER

12VDC

GND

12V

Strengthen security with AR-721RB

12V

GND

Electric Bolt

ARM

12V

GND

1 2 3

4 5 6 7 8

12V GND

1 2 3

Controller

POWER

12VDC

1.Enable the security trigger signal: Please refer to the 34 DDD

※

12V

GND

N.C. N.O.

COM

CTL 12V

GND

POWER

AR-721RB

N.O.

Request To Exit

12VDC

EXIT

Controller

POWER

12VDC

Connect to Door Sensor

POWER

12VDC

Door Contact

Controller

POWER

12VDC

Connect to Networking

Converter

Node ID 001

AR-716E

Controller

Node ID 254

2.Disable "Exit by RTE Button". (Please refer to the 20 DDD of function default value.)

Connect to Access Control for Connect to arming tools for

Lock

12V

GND

POWER

12VDC

211 1

9 8 7 6 5 4 3 2 1

Request To Exit

N.O.

AR-331 (H)

POWER

12VDC

P7 P7

Door

ALM

COM

N.O.

12V

GND

1 1 1 1 10

Door Contact

4 3 2 1

9 8 7 6 5 4 3 2 1

EXIT

12V

GND

Electric Bolt

N.C. N.O.

COM

CTL 12V

Relay Outpot Module

If use the AR-721RB, please refer to the top of the wiring diagram.

AR-331 (H)

Contact

POWER

12VDC

N.C.

N.O.

Request To Exit

12V

GND

Alarm

N.C. N.O.

COM

CTL 12V

Relay Outpot Module

N.C.

GND

12V

Node 1

B-

A+

Controller

B-

A+

Node 9

Alarm

N.C. N.O.

COM

CTL

12V

CTL

COM

N.O. N.C.

Tamper Alarm

EXIT

Door Contact

POWER

12VDC

Node 8

B-

A+

Controller

B-

A+

Node 16

Alarm Relay

Tamper Relay

SOYAL

ACCESS CONTROL SYSTEM

AR- 321H

Connect to Reader for Connect to Networking for P7P7

GLED

Reader

POWER

12VDC

External WG keyboard

If you want to program system on AR-331 (H-S) directly, please order WG keyboard then install it according to the following pattern.

※

RLED

BZ WG 1 WG 0

GND

12V

GND

12V

AR-721(H) / AR-725 (H) / AR-757 (H)

AR-321 (H) / AR-331 (H) /

1 2 3 4 5 6 7 8

9 10 11

1 1

4 5

12V

GND

AR-331 (H)

POWER

12VDC

AR-331 (H)

12V

GND

A+

211 1

9 8 7 6 5 4

B-

3 2 1

A+

B-

Converter

B-

Host

A+

B-

CH1

A+

B-

CH2

A+

AR-716E

Remove the Protection plug that at the right bottom.

(※ Do not lose protection plug or it will affect the protection level.)

WG Keyboard cable will be connected to the pin board.

WG Keyboard connected to the controller from the bottom right of the hole.

When you nish programming system, please put protection plug back to

the controller.

AR-331 (H) Interaction Area

331 (HB): 125kHz 331 (HD): 13.56MHz

V140707

331 (HB) touch card-area for interaction.

※

CARD

Metal controller's Presenting scope is smaller than others, and EM:331 (HB) / MIFARE:331 (HD) is different. Refer to the above picture.

Adding and Deleting Tag

M4/M8

Add a Single Tag or Random tags

Input 123456 (or Master Code)

[e.g.] Add 2 random cards to User Addresses No. 100 and No. 101:

Enter program mode

19 00100 00001

→

Add a batch of Sequential tags

Input 123456 (or Master Code)

[e.g.] Add 20 pcs sequential tags (62312~62331) to User Address NO.101 ~ NO.120:

Enter program mode

19 00101 00120

→

Delete Single Tag

Input 123456 (or Master Code) [e.g.] Delete User Address: 00058

Enter program mode

10 00058 00058

→

Delete a batch of Tags

Input 123456 (or Master Code)

[e.g.] Delete User Address: 00101~00245

Enter program mode

10 00101 00245

→

Delete All Tags

Input 123456 (or Master Code)

In this mode, User Address = Card Code

※

Add Tags

Input 123456 (or Master Code) [e.g.] Add User Address: 00100~ 01254

Enter program mode

11 00100 01254

→

Delete Tags

Input 123456 (or Master Code)

[e.g.] Delete a tag with card code 62362

Enter program mode

10 62362 62362

→

19 UUUUU 00001

→

Present the tags one by one

→

19 UUUUU QQQQQ

→

Close Tag into RF Area

→

10 SSSSS EEEEE

→

10 SSSSS EEEEE

→

29 29

→

11 SSSSS EEEEE

→

10 SSSSS (or )EEEEE

→

Present the tag(s) to Access Controller

→

Present the tag

→

CARD

Done

→

(only use th e tag wit h the lowest number)

(only use th e tag NO .623 12)

Tag Information

Delete All Tags

Input 123456 (or Master Code)

331 (HD) touch keyboard area for interaction.

※

(single tag or rand om tags o ne by one)

→

(125kHz) ※ For Mifare tags, the separator between Site Code & Card Code is comma "

CARD CODE

SITE CODE

29 29

→

Done

→

CARD CODE

Access Controller

Touch-panel Metal Housing / Illuminated Touch-panel

Operation process

A. Enter / Exit Program Mode

Enter the program mode

Input 123456 or PPPPPP [e.g.] The Default Value= 123456, if the Master Code is already changed= 876112, input

Exit the program mode

Input

Master Code modication

Enter program mode [e.g.] Set the Master code to be 876112, input

09 PPPPPPRRRRRR [Input the 6-digit new master code twice.]

→

B. Change the Node ID of Controller

Enter program mode

00 NNN [Node ID: 001~254; if the access controller is connected to AR-716E, its Node ID will be 001~016.]

→

C.Set up M4/M6/M8

Enter program mode

04 N [N=4/6/8]

→

D. Set up the password

M4/M8: Private PIN

Card or PIN: Enter program mode

Card and PIN: Enter program mode

M6: Public PIN

Card or PIN: Enter program mode

Card and PIN: Enter program mode

12 UUUUU PPPP [e.g. User Address: 00001 and pass code: 1234, input 12 00001 1234 ]

→

13 UUUUU PPPP [e.g. User Address: 00001 and pass code: 1234, input 13 00001 1234 ]

→

15 PPPP [Input 4- digit PIN, default value: 4321; PPPP=0000:

→

17 PPPP [Input 4-digit PIN, default value: 1234; PPPP=0000: access mode will be "Card Only"]

→

E. Double Door Control (M4/M8)

Controller with a reader to per form the "Double Door Control".

Enter program mode

28 064 [064= Double Door Control]

→

F. Anti-pass-back (M4/M8)

Usually, anti-pass-back is commonly applied to parking areas in order to prevent from multi-entry with one card at a time, or to locations that need entry and exit control.

Enable controller

Enter program mode [e.g.] Enable Anti-pass-back, and set to Exit door= (128 x 1) + (064 x 0) = 128

Enter program mode

Enable card

Enter program mode

[SSSSS= Starting User Address; EEEEE= Ending User Address; N=0(control)/ 1(Not control)/ 2(reset)] [e.g.] Enable the anti-pass-back function of User Address from 00152 to 00684: 26 00152 00684 0

[e.g.] The anti-pass-back function of User Address 00154 has been enabled. After presenting the card to get in, the user doesn’t present the card to leave. When s/he tries to present the card to get in again, since the in-in sequence violates the anti-pass-back rule, s/he will be rejected. To solve this problem, you can reset it as follows. Enter program mode

20 DDD [128= Anti-pass-back(0=Disable; 1=Enable)/ 064=Entrance/Exit(0=Exit; 1=Entrance).]

→

20 128 (Please refer to function default value for details.)

→

26 SSSSS EEEEE N

→

26 00154 00154 2

→

G. Auto-Open Time Zone

Door will remain open after the rst ashing card. There are 2 time zones supported when Standalone, and 63 time zones when connected to AR-716E.

Enable/Disable auto-open time zone

Enter program mode

Enable/Disable auto open door without presenting card

Enter program mode

Set up auto-open time zone

Enter program mode

N: 2 sets of auto-open zone (N=0=1st set; N=1=2nd set)

HHMMhhmm=Staring time to ending time (e.g. 08301200=08:30 to 12:00)

7123456H= 7 days of a week (Sun/Mon/Tue/Wed/Thu/Fri/Sat) + Holiday (H= 0: disable; 1: enable); Holidays can be set via 701Client software. [e.g.] To set the second time zone as 9:30 AM to 4:20 PM, Monday, Wednesday and Friday: 08 1 09301620 01010100

20 004 [004= enable Auto-Open Time Zone; 000 = disable Auto- Open Time Zone]

→

24 001 [001= enable Auto-Open Time Zone; 000= disable Auto-Open Time Zone]

→

08 N HHMMhhmm 7123456H

→

H. Lift control

Connect with AR-401RO16B to control access oors of users.

Enable

Enter program mode

Single oor

Enter program mode

UUUU=User Address FF=Floor number (01~32 oor)

[e.g.] User Address NO. 45, allowed to access the 24th oor: 27 00045 24

Multi oors

Enter program mode

[UUUUU=User Address S: 4 sets of lift control (Input: 0 ~3) FFFFFFFF: 8 oors setting (F=0: Disable, F=1: Enable)

[e.g.] User Address NO. 168, only to the 6th and the 20th oor:

Enter program mode

24 002 [002= enable lift control]

→

27 UUUUU FF

→

21 UUUUU S FFFFFFFF

→

21 00168 0 00100000

→

21 00168 2 00001000

→

87 6112

→

program mode entered

→

12345 6

Reset

Please refer to below oor chart

Set

0 1 2 3

09 87 6112 8 7 6112

→

cancel the function of simply inputting PIN to get access

Floor/ Stop

7 16 24 32

15 23 31

14 22 30

Done

→

V140707

]

SOYAL

ACCESS CONTROL SYSTEM

I. Setting Up the Arming

Alarm conditions:

1. Arming is enabled

2.Alarm system connected

Enable/Disable Arming status (for M4/M8; default value of arming PWD is: 1234) :

Standby Mode

After door open

AR-721(H) / AR-725 (H) / AR-757 (H)

AR-321 (H) / AR-331 (H) /

Application:

1. Door open too long: Door is open longer than door relay time plus door close time.

2. Force open (Opened without a valid user card): Access by force or illegal procedure.

3. Door position abnormal: Arming is enabled and the power is suddenly off then on.

V140707

Do not open the door

Input 4-digit arming PWD

The normal procedure to open door

Enter Program Mode

Enable: Enter program mode

[The normal procedure to open door] can refer to [Access Mode].

※

Function Default Value

→

Input 4-digit arming PWD

→

Disable: Enter program mode

AR-321 (H) / AR-331 (H) / AR-721 (H) / AR-725 (H) / AR-757 (H)

Default Value

20 DDD

Function Selection Value Application

Time Attendance

Auto Relock

Auto Open

Exit by RTE Button

Master Controller of Network

Entrance/Exit

Anti-pass-back

0: Ye s

※

0: Disable

※

0: Disable

※

0: Disable

0: Slave

※

0: Exit

※

0: Disable

※

1: No

1: Enable

※

1: Mat er

Entrance

1: Enable

Networking

001

Networking/Standalone

002

Networking/Standalone

004

Networking/Standalone

016

Networking

032

Networking

064

Networking

128

28 DDD

Function Selection Value Application

Double Door Control

Force Open Alarm Output

0: Disable

※

0: Disable

1: Enable

※

Networking/Standalone

064

Networking/Standalone

128

※

Default Value

※

AR-321 (H) / AR-331 (H) / AR-721 (H) / AR-725 (H) AR-757 (H)

Default Value

24 DDD

Function Selection Value Application

Auto Open without Presenting

in Auto- open Time Zone

Alarm Output/ Lift

Control

Stop Alarm by pressing RTE

Button or Closing the Door

Doorbell

0: Disable

※

0: Alarm Output

※

0: None

0: Disable

※

1: Enable

※

1: Enable

1: Lift Control

1: Yes

001

002

064

128

※

Networking/Standalone

24 DDD

Function Selection Value Application

Auto Open without Presenting

in Auto- open Time Zone

Lift Control/

Duress Function

Stop Alarm by pressing RTE

Button or Closing the Door

Present a valid card

→

Select the desired function, Weighted Value = Selection Index (0 or 1) x Value. [e.g.] DDD (total weighted value of all functions): Enable "Auto Open" + "Exit by RTE Button" + "Antipass-back"=1*004 + 1*016 + 1*128=148; As a result of that, the command will be 20 148 .

Default Value

※

0: Disable

※

0: Duress

※

0: None

1: Enable

1:Lift Control

1: Yes

※

Networking/Standalone

001

Networking/Standalone

002

Networking/Standalone

064

M4 / M6 / M8

Networking/

Mode

Standalone

Networking/

Standalone

Networking/

Standalone

M6: the user capacity can be 65535 because it only reads 5-digits CARD CODE, while in M4/M8 it reads both SITE CODE and CARD CODE(10 digits).

※

Factory Reset by its commands

When the device is Standalone (not networking)

Enter program mode

Note: if the Master Code has been changed, factory reset won't restore the Master Code to 123456.

※

User

Capacity

1,024

{721 (H)/ 757 (H)}

3,000

{321 (H)/3 31 (H)/

725 (H)}

65,535

1,024

{721 (H)/ 757 (H)}

3,000

{321 (H)/3 31 (H)/

725 (H)}

→ 20

1.Card only

2.Card and PIN

3.User Address

1.Card only

2.Card and PIN

3.Card or PIN

1.Card only

2.Card and PIN

3.Card or PIN

016

(using 17* command to set Armi ng PWD as 0 000)

→ 24

Access Mode

(4-digit PIN)

(5-digit)

(4- digit public PI N= Arming PWD)

(4-di git public PIN= D uress code)

(4- digit Private PI N)

(4-di git Pri vate PIN)

+ PIN

064

→ 26

Auto-show

Duty time

00000

Yes

01023

1 → 28

Event log

Capacity

721 (H)

1,200

1,500

321 (H)/3 31 (H)/

725 (H)

757 (H)

3,000

721 (H)

1,200

1,500

321 (H)/3 31 (H)/

725 (H)

757 (H)

3,000

000

120

Holidays

Yes

→ 29

Duress

Function

Yes

Time Zone

Lift

Control

Anti-pass-

back

Yes

Command List

Function

Enter program mode

Exit program mode

Exit p rogram mode and ent er arming mo de

Node ID setting (Connected to 716E)

Node ID setting (Con necte d to the PC di rectl y

without 716E)

Mifare tag / c ard for mat (Optional)

Door Re lay Tim e sett ing

Alar m Relay Time set ting

Control mode setting

Arming Dela y Time se tting

Alar m Delay T ime settin g

Master card (Administrator) setting

Auto- open time zone set ting

Master code sett ing

Suspe nd / Del ete ta g

Add a bat ch of seq uent ial ca rds by in putt ing ca rd

number (M6)

Recover the suspended cards

Set the a cces s mode o f the us er at th e desig nate d

User Address as "Car d or PIN"

Set the a cces s mode o f the us er at th e desig nate d

User Address as "Car d & PIN"

Arming Pulse T ime se ttin g

M4/M 8:Duress cod e setting

M6:Pub lic PIN s etti ng for ac cess m ode "Ca rd or PIN "

Card nu mber modication

M4/M 8:Arm ing PW D sett ing

M6:Pub lic PIN s etti ng for ac cess m ode "Ca rd & PIN"

Door Close Time

Add car d by pres enti ng(M4 /M8)

Reader additional setting

Lift c ontrol setting: multi-oo r

Add/Delete tag by presenting (M6 only)

AR-4 01RO16 Lif t Relay A ctiva ted TM

Controller parameter setting

Controller time clock setting

Anti-pass-back (Enable user)

Lift c ontrol setting: si ngle  oor

Doubl e Door Cont rol / Force Ope n Alarm

Delete all tags

Enabl e the se curi ty tr igge r signa l ( with A R-721RB)

Access Controller

Touch-panel Metal Housing / Illuminated Touch-panel

Command

PPPPPP

00 NNN

00 NNN VVV nnn

01 N

02 TTT

03 TTT

04 N

05 TTT

06 TTT

07 SSSSS EEEEE

08 N HHMMhhmm 7123456H

09 PPPPPPRRRRRR

10 SSSSS EEEEE (M6)

10 SSSSS EEEEE (M4/M8)

11 SSSSS EEEEE

12 UUUUU PPPP

13 UUUUU PPPP

14 TTT

15 PPPP

16 UUUUU SSSSSCCCCC

17 PPPP

18 TTT

19 UUUUU QQQQQ

20 DDD

21 UUUUU S FFFFFFFF

22 N

23 NNN TTT

24 DDD

25 YYMMDDHHmmss

26 SSSSS EEEEE N

27 UUUUU FF

28 DDD

29 29

34 128

34 064

(321H/721H/725H/757H)

(331H)

34 000

(Disable)

Description

PPPPPP=Master Code, default value=123456

NNN= Node I D of Acce ss Cont rolle r (range: 0 01~016)

NNN= Node I D of Acce ss Cont rolle r (range: 0 01~254)

VV V=Vir tual 716E No de ID, nnn= Door number (ra nge:001~254)

N: 0=ISO14443A; 1=ISO14443B; 2=ISO15693;

3=I Code1; 4=I Code2

PS.1. Please select the t ransmi ssion s tandard rst.

2. Ensure b oth reader and card usin g the same transm issio n standa rd.

TTT=Door relay t ime 000= Output continuously

001~600=1~600 sec.

601~6 09=0.1~0.9 sec.

TTT=Alarm relay time 000= Output continuously 001~600=1~600 sec.

N=4: M 4; N=6: M 6; N=8: M8

TTT=the buffer time before entering arming mode 001~600=1~600 sec.

TTT=th e buffer time be fore the alarm is activat ed 001~600=1~600 sec.

SSSSS-EEEEE=00000-01023 (00000-03000 for AR-725H);

SSSSS=Starting User Address; EEEEE=Ending User Address

N= 0 (1st time zone) / 1 (2nd time zon e)

HHMM = Star ting t ime; hhmm = ending t ime

(i.e.: 0 83016 00 =08:30 to 16: 00)

7123456H= 7 days of we ek (Sun/ Mon/ Tue/We d/T hu/Fri /Sat)+ H oliday

(H= 0: dis able; 1: enab le); Holidays can be set by 701Client s oftware.

PPPPPP=6- digit new master code

RRRRRR=Reconr m the new master cod e

=Suspend =Delete;

SSSSS=Starting User Address, EEEEE=Ending User Address

SSSSS=Starting card number

EEEEE=Ending card number

SSSSS=Starting User Address

EEEEE=Ending User Address

Acces s mode: Card or PI N; UUUUU=User Address;

PPPP=4-digit pr ivate PIN (0 001~999 9); 0000=Car d Only for this user

Acces s mode: Card & PIN; UUUUU=User Address;

PPPP=4-digit private PIN (0000~9999)

TTT=Ar ming out put tim e; 000 =outp ut cont inuous ly 001~25 0=0.1~2.5 sec.

PPPP=4-digit duress code (0001~ 9999; defa ult value =4321; 0000=disable

the func tion of s imply in putting PIN to get access in M6)

UUUUU= User Address; S SSSS =5- digi t site co de; CCCCC=5 -digit card c ode

PPPP=4 -digit Ar ming PW D (0001~ 999 9; default value =1234 ; 0000= a cc ess

mode will beco me "Car d Only " in M6)

TTT=Door Close Time: 0 01~60 0=1~ 600 s ec.; defa ult value: 15 se c.

UUUUU=User Address; QQQQQ=Card quantity (00001: fo r adding a s ingle

card or a b atch of random num berin g cards)

Please refer to function default value for d etails .

UUUUU=Use r Address , S=4 sets of lift control (0~3); FFFFFFFF=8 assi gned oo r

(F=0: Di sable, 1: Ena ble)

N=0(Delete tag); N=1(Add t ag)

NNN=site numb er, TTT= relay t ime: 00 0~ 600=1~6 00 sec.

Please refer to function default value for d etails .

YYM MDDH Hmms s: Year/ Month / Day/ Hour/ Min./ Se c.

SSSSS=Starting User Address; EEEEE=Ending User Address;

N=0: En able; N=1: Di sable; N =2: Reset

UUUUU=Use r Address; FF= Floor (01~32 oo r)

Please refer to function default value for d etails .

Change t he "Armi ng" (in ) to the security trigge r signal ,

when co ntroll er is co nnecte d with AR-721RB.

V140707

Mode

M4/M6/M8

M4//M6M8

M4/M8

M4/M6/M8

M4/M8

M4/M6/M8

M4/M8

M4/M6/M8

M4/M8

M4/M6/M8

M4/M8

M4/M6/M8

M4/M8

M4/M6/M8

M4/M8

M4/M6/M8

Soyal AR-331, AR-331H, AR-321, AR-721H, AR-725 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual