Sovereign 37 cc Operating Instructions Manual

Download

Page 1

HS-CS 37/1; EX; UK

Petrol Chain Saw

Artikel-Nr.: 4501642

Ident-Nr.: 11011

Page 2

Komponenten / Ersatzteile

Position Artikel-Nr. Beschreibung 24 450164002024 hex flange nut M8 M8

25 450164201025 air filter cover (black) (schwarz)

26 450164002026 air filter lock nut für Luftfilterabdeckung

27 450164002027 washer for lock nut 15x26x1

28 450164002028 air filter

37 450164002037 wind guide

46 450164002046 self-tapping screw ST4.8x25 für Seilzugstarter

48 450164002048 cushion socket 1

52 450164002052 front handle spring

53 450164002053 front handle

54 450164002054 cover plate for spring

65 450164002065 base spring

71 450164002071 pin 5x24 5 x 24

72 450164002072 extinction switch

73 450164002073 fuel pumping bulb

74 450164002074 pump tube

75 450164201075 trigger control rack (grey) (Pantone cool grey 3c)

76 450164002076 trigger torsion rod spring

77 450164002077 trigger

79 450164002079 handle cover

83 450164002083 carburetor

84 450164002084 air-intake socket für Luftfilter

85 450164002085 screw for carburetor für Vergaser

88 450164002088 bar guard für Leitschiene

91 450164002091 spark plug spanner

92 450164002092 file

93 450164002093 screw driver

94 450164002094 engine 1,2 kW / 1,6 PS / 37,2 ccm

901 450164002901 right cover assy.

901 450136001001 Right cover assembly

902 450164201902 starter assy. (red) Pantone 1805C

903 450164002903 balancer body assy.

904 450164002904 fuel tube assy.

905 450164002905 petrol cap assy.

906 450164002906 oil cap

0 450164002095 oil mixing bottle

Page 3

engine Artikel-Nr.: 450164002094

Ident-Nr.:

Page 4

Komponenten / Ersatzteile

Position Artikel-Nr. Beschreibung

202 450164002202 nut M5 M5

203 450164002203 spring washer 5

204 450164002204 flat washer 5

207 450164002207 muffler body

208 450164002208 sealing washer for muffler für Auspuff

211 450164002211 spark plug NHSP LD L8RTF L8RTF

212 450164002212 sealing washer for air intake tube

214 450164002214 sealing plate carburetor für Vergaser

215 450164002215 sealing plate for cylinder

216 450164002216 piston ring

217 450164002217 piston pin

218 450164002218 piston pin circlip

219 450164002219 piston

223 450164002223 woodruff key 3x3.5x10 3 x 3,5 x 10

228 450164002228 circlip 32

229 450164002229 oil seal 12x32x5.5 12 x 32 x 5,5

232 450164002232 tension block

233 450164002233 adjust screw M5x48 M5 x 48

234 450164002234 spike bumper

235 450164002235 screw M5x12 M5 x 12

236 450164002236 chain block

237 450164002237 screw for chain block für Kettenfänger

238 450164002238 baffle

239 450164002239 screw M4x10 M4 x 10

241 450164002241 igniter mit Zündkerzenstecker

242 450164002242 screw M4x14 M4 x 14

243 450164002243 spring washer 4

245 450164002245 flange nut M8x1 M8

253 450164002253 adjusting washer for cluch

254 450164002254 clutch shell

255 450164002255 needle bearing 10x13x13 10 x 13 x 13

256 450164002256 worm

258 450164002258 oil pump

259 450164002259 oil outlet tube 3x6.5x75 3 x 6,5 x 75

260 450164002260 washer for worm 10x18x1 10 x 18 x 1

261 450164002261 oil inlet tube 3.5x6.5x68 3,5 x 6,5 x 68

262 450164002262 circlip for oil tube

263 450164002263 tie-in

908 450164002908 flywheel assy

909 450164002909 clutch assy

910 450164002910 base assy.

Page 5

Important - Please read these instructions fully before starting assembly

These instructions contain important information that will help you get the best from your chainsaw, ensuring it is assembled correctly and safely. If you need help or have damaged or missing parts, call the Customer Helpline on 0151 649 1500.

Feb 2011

UK/Ireland 0151 649 1500 Republic of Ireland 1890 946 244 Web www.einhell.co.uk

After Sales Support

Operation and Maintenance Manual

Sovereign 37 cc Petrol Chainsaw

Original Operating Instructions

Page 6

Contents

Customer Helpline 0151 649 1500

Components List .......................................................................................................................................... 4-5

Safety Information ...........................................................................................................................................6

Warnings Symbols ......................................................................................................................................6

Explanation of the Symbols and Warning signs on the machine labels .............................................. 7-8

General Safety .............................................................................................................................................9

Personal Safety ............................................................................................................................................9

Operating and Maintenance Safety .........................................................................................................10

Handling Safety ........................................................................................................................................11

Proper Use .......................................................................................................................................... 12-13

Kickback Safety .........................................................................................................................................13

Pinching Safety ..........................................................................................................................................14

Preparing to Operate the Chainsaw .........................................................................................................15

Step 1 - Assemble the Chainsaw ..............................................................................................................15

Step 2 - Check the Chain Brake ......................................................................................................... 15-16

Step 3 - Fuel and Lubrication ............................................................................................................. 17-18

Step 4 - Filling the Fuel Tank ....................................................................................................................19

Step 5 - Filling the Chain Lubrication Oil Tank ........................................................................................20

Operating the Chainsaw ................................................................................................................................21

Step 1 - Starting the Engine ............................................................................................................... 21-26

Step 2 - Restarting the Chainsaw When Warmed Up .............................................................................27

How to Use the Chainsaw .............................................................................................................................28

Introduction ................................................................................................................................................28

Felling ................................................................................................................................................... 29-30

Limbing ......................................................................................................................................................31

Bucking ......................................................................................................................................................32

Page 7

Contents

Customer Helpline 0151 649 1500

Storing the Chainsaw ....................................................................................................................................33

Step 1 - Storing the Chainsaw for Short Periods ....................................................................................33

Step 2 - Storing the Chainsaw for Extended Periods ...................................................................... 33-35

Step 3 - Preparing the Chainsaw for Use Following Storage ................................................................35

Maintenance ...................................................................................................................................................36

Maintenance Schedule .............................................................................................................................36

Step 1 - Operational Chain Brake Test ....................................................................................................37

Step 2 - Clean / Replace the Air Filter ............................................................................................... 38-39

Step 3 - Change / Replace the Fuel Filter ......................................................................................... 40-42

Step 4 - Clean / Replace the Spark Plug ........................................................................................... 42-46

Step 5 - Carburettor Settings ...................................................................................................................47

Step 6 - Lubricating the Sprocket Tips .............................................................................................. 47-48

Step 7 - Reversing the Guide Bar .............................................................................................................49

Step 8 - Adjusting the Automatic Chain Lubricator ................................................................................49

Step 9 - Check the Saw Chain Tension ....................................................................................................50

Step 10 - Sharpening the Saw Chain .......................................................................................................51

Troubleshooting .............................................................................................................................................52

General Troubleshooting ..................................................................................................................... 51-53

Useful Information .........................................................................................................................................53

Technical Data ...............................................................................................................................................54

Technical Data Table .................................................................................................................................54

Disposal ..........................................................................................................................................................54

Disposal Instructions ................................................................................................................................54

Guarantee ......................................................................................................................................................55

Declaration of Conformity .............................................................................................................................56

Page 8

Customer Helpline 0151 649 1500

Components List

Saw chain

Chain bar

Chain brake lever/ front hand guard

Air ﬁlter cover

Safety lock

Primer

Rear handle/ bootstrap

Throttle lever

Chain tensioning screw

Bar fastening nut

Chain catch

Stop claw

Chain guard

Page 9

Customer Helpline 0151 649 1500

Components List

Choke/ (carburettor setting)

Spark plug (under the air ﬁlter cover)

Starter handle

Front handle

Oil tank cap

Fan housing

Fuel tank cap

Stop switch

Page 10

Safety Information

Important - Please read these instructions fully before operating or maintaining

Customer Helpline 0151 649 1500

The following warning symbols appear throughout this assembly manual and indicate the appropriate safety measures you should take when assembly and operating the chainsaw.

This symbol indicates there is a danger of serious personal injury or death if you do not observe the warning.

This symbol indicates that there is: -

1. Danger of permanently damaging your hearing if you do not wear ear defenders

2. Danger of permanently damaging your sight if you do not wear suitable goggles or glasses

3. Danger of suffering serious head injuries if you do not wear a suitable helmet

This symbol indicates that there is a danger of damaging your hands if you do not wear thick, hard wearing gloves.

This symbol indicates that there is a danger of damaging your feet if you do not wear protective shoes or boots.

This symbol indicates there is a danger of serious personal injury if you attempt to make adjustments to the chainsaw while it is running.

This symbol indicates there is a risk of explosion if you do not observe the warning.

This symbol indicates there is a risk of igniting ﬂammable liquids if you do not observe the warning.

This symbol indicates there is a danger of serious personal injury if you attempt to grasp or come into contact with a moving saw chain.

This symbol indicates there is a danger of kickback if you fail to observe this warning.

Warnings Symbols

Page 11

Safety Information

Important - Please read these instructions fully before operating or maintaining

7Customer Helpline 0151 649 1500

Explanation of the Symbols and Warning signs on the machine

Explanation of the symbols on the warning label on the machine.

Read the user manual before using the machine.

On all jobs performed with the saw you must always wear safety goggles to guard your eyes from ﬂying materials/objects and ear defenders to protect your hearing. Wear a safety helmet if there is a risk of objects falling on you from above.

Important! Wear gloves to protect your hands.

Wear safety shoes to protect your feet.

Warning! Danger!

Make sure that the chain brake is released. Pull back the handle/chain brake before operating.

Noise emission complies with Directive 2000/14/EC.

Explanation of the symbols for the handling label on the machine.

A safety sign is ﬁtted to the chain saw’s fan ﬁlter cover. This label, along with the safety instructions on these pages, should be carefully read before attempting to operate this unit.

IMPORTANT! Picture 1/2/3 Warns about a dangerous method of working that must not be used. Picture 4 Recommends operation for safe sawing.

1. Avoid contact with the tip of the chain bar (chain return point). RECOMMENDED.

2. Warning! Beware of kick back.

3. Do not hold the saw in one hand.

IMPORTANT! Hold the saw ﬁrmly with both hands. Place your right hand on the rear handle and your left hand on the front handle.

Page 12

Safety Information

Important - Please read these instructions fully before operating or maintaining

Customer Helpline 0151 649 1500

Explanation of the symbols for the brake function label on the machine.

Push the handle forward to engage the brake, and stop the chain.

Push the handle back to disengage the brake.

NOTE! The chainsaw is designed for occasional use by home owners, garden owners and campers and is for general work such as stump grubbing, cutting ﬁrewood, etc. It is not designed for lengthy use. If it is used for a lengthy period, the vibrations it causes in the hands of the user may result in circulation problems (white ﬁnger syndrome).

Explanation of the Symbols and Warning signs on the machine continued

Page 13

Safety Information

Important - Please read these instructions fully before operating or maintaining

9Customer Helpline 0151 649 1500

WARNING! Only operate the chainsaw if you are wearing the correct Personal Protective Equipment (PPE) as described in the following warnings.

WARNING! Always wear a suitable helmet and footwear if you are operating the chainsaw where there is a risk of falling objects i.e. under a tree canopy.

WARNING! Never wear loose ﬁtting clothing while operating the chainsaw.

WARNING! Never operate the chainsaw for extended periods of time. You may become tired or

lose concentration. This may create unnecessary risks to yourself and others. Take periodic breaks whenever possible.

WARNING! Read and follow the operating instructions and safety information before using for the ﬁrst time. Keep this operating and maintenance manual in a safe place for reference at a later date.

WARNING! Always ensure anyone intending to operate this chainsaw is fully conversant with the contents of this manual prior to maintaining or operating the chainsaw.

WARNING! Only perform operations described in this manual. Failure to observe this warning may lead to serious injury, death, or damage to the chainsaw.

WARNING! This chainsaw must only be used for light domestic applications such as sawing wood in your own garden. It is not a commercial, trade or industrial product and must not be used for extended periods of time. Extended use may lead to circulatory problems. Always seek guidance and appropriate training before attempting to fell trees or perform sawing operations on large trees or tree stumps.

WARNING! This chainsaw is only designed to saw wood. Under no circumstances should you attempt to saw plastic, masonry or metallic materials.

WARNING! Always take the time to fully inspect the chainsaw for signs of damage each and every time it is used. If any signs of damage are observed, do not use the chainsaw until it has been fully inspected by a suitably qualiﬁed service technician.

CAUTION! The saw chain will stretch after as few as ﬁve cuts following the initial tensioning. Refer to the operation and maintenance manual for instructions on re-adjusting the saw chain tension.

CAUTION! Only operating and maintenance procedures speciﬁcally detailed in this manual or the maintenance manual should be carried out. All other procedures must be carried out by a suitable qualiﬁed service technician.

IMPORTANT! Before assembling the chainsaw, check all the parts indicated in the Assembly Manual are in the box. Inspect all the parts for signs of damage. Do not assemble the chainsaw if you observe any damaged components.

NOTE! This chainsaw complies with the Noise Emission Directive 2000/14/EC.

General Safety

Personal Safety

Page 14

Safety Information

Important - Please read these instructions fully before operating or maintaining

WARNING! Under no circumstances should the chainsaw be ﬁlled or reﬁlled with the fuel mixture or oil while the engine is running. Failure to observe this notice may present a risk of explosion.

WARNING! Under no circumstances should you attempt to lubricate any part of the chainsaw while the engine is running.

WARNING! Always turn the engine off before setting the chainsaw down. Failure to observe this warning may allow the chainsaw to be accidentally operated leading to serous personal injury.

WARNING! Never attempt to clear trapped debris from the saw chain while the engine is running.

WARNING! Under no circumstances should you attempt to grasp the saw chain while it is moving.

Failure to observe this warning may lead to serious personal injury.

WARNING! To stop the chainsaw in an emergency, apply rapid pressure to the chain brake and stop switch.

WARNING! If the chain brake fails the operational chain brake test, DO NOT use the chainsaw until it has been serviced and inspected by a suitably qualiﬁed technician.

WARNING! Always store excess fuel/oil mixtures drained from the fuel tank in a suitable sealed container designed for the storage of ﬂammable liquids.

CAUTION! Only use the large end of the supplied multi tool to remove the spark plug. Using any other tool may damage the spark plug and/or the chainsaw engine.

CAUTION! Although the guide bar is pre-lubricated at the factory, it is essential that you regularly lubricate the guide bar in accordance with maintenance schedule. Failure to observe this caution will inhibit the performance of the chainsaw and may void your warranty.

CAUTION! It is essential that the correct saw chain tension is maintained. This will ensure that the saw chain, drive sprocket, guide bar and engine do not wear prematurely.

WARNING! Always ensure the chainsaw is operated in a safe area free from objects or surfaces which may lead to tripping, slipping or loss of secure footing. Always ensure you have a planned retreat path from a tree which is to be felled.

WARNING! Periodically inspect the work area for possible hazards while using the chainsaw.

CAUTION! Always operate the chainsaw in well ventilated areas.

WARNING! DO NOT allow other persons to be near when starting or cutting with the chain saw.

Keep bystanders and animals out of the work area.

WARNING! The engine will create toxic exhaust fumes as soon as the engine is started. Never work in enclosed rooms or in rooms with poor ventilation.

Operating and Maintenance Safety

Customer Helpline 0151 649 1500

Page 15

Safety Information

Important - Please read these instructions fully before operating or maintaining

11Customer Helpline 0151 649 1500

WARNING! Always hold the chainsaw with two hands while operating. This chainsaw is not designed for single-handed operation. Failure to observe this warning may lead to loss of control and may present a serious threat of personal injury or death to yourself and others.

WARNING! Never attempt to operate or maintain the chainsaw while tired or in a situation where you may be easily distracted.

WARNING! Do not operate the chainsaw if you have a medical condition which may affect your ability to operate it safely. If unsure, seek medical advice.

WARNING! Never attempt to operate or maintain the chainsaw under the inﬂuence of drugs and/or alcohol. Your ability to operate chainsaw safely may be reduced, leading to serious injury, death or damage to the chainsaw.

WARNING! Never expose any part of the body to saw chain while the engine is running. Failure to observe this warning my lead to serious injury or death.

WARNING! Always ensure the chain brake works correctly before operating the chainsaw by performing the chain brake mechanical test. Never use the chainsaw if the chain brake is damaged, fails to operate correctly or is not assembled correctly.

WARNING! Never start the chainsaw in close proximity to stored fuel. Failure to observe this warning may lead to inadvertent ignition of stored or spilled fuel leading to personal injury.

WARNING! Never attempt to operate the chainsaw at heights or in a tree at any time. Failure to observe this warning may lead to serious personal injury to yourself and others.

WARNING! Always ensure the handles and controls of the chainsaw are dry and free from grease, mixed fuel, oil or any other lubricant. Failure to observe this warning may lead to loss of control and serious personal injury or death.

CAUTION! Never use the chainsaw to saw/cut small bushes, shrubs or saplings. The branches of these may get caught in the cutting blades of the saw chain and whipped towards you or pull you off balance.

CAUTION! Always be alert when sawing branches under tension. Once sawn/cut, the tension will be released. You may become unbalanced or struck by loose objects.

CAUTION! When the chainsaw is not in use, always carry it by the handle with the saw chain and guide bar facing rearwards. Whenever possible, cover the saw chain with the protective cover provided.

CAUTION! During operation, the chainsaw will exhaust hot gases. Keep all exposed parts of the body away from the exhaust.

WARNING! If your ﬁngers become white or you feel an awkward feeling (prickle) in your ﬁngers, stop working immediately!

Handling Safety

Page 16

Safety Information

Important - Please read these instructions fully before operating or maintaining

The chain is designed exclusively for sawing wood. You may only fell trees if you have received the appropriate training. The manufacturer cannot be held liable for damage caused by improper or incorrect usage.

Residual hazards Even when the equipment is used properly, a certain residual hazard cannot be ruled out. The following potential dangers may arise in connection with the equipment’s design and construction:

WARNING! Contact with the unguarded saw chain (injuries through cutting).

WARNING! Reaching into the saw chain while it is running (injuries through cutting).

WARNING! Unforeseen, sudden movement of the saw chain (injuries through cutting).

WARNING! Catapulting of parts of the saw chain.

WARNING! Catapulting of parts of the material being cut.

WARNING! Damage to hearing if the compulsory hearing protection is not used Inhalation of particles from the material being cut, emissions from the combustion engine.

WARNING! Skin contact with petrol.

The machine is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.

NOTE! Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.

WARNING! The following information is primarily for the end user or occasional user. The chainsaw is designed for occasional use by home owners, garden owners and campers and is for general work such as stumpgrubbing, cutting ﬁrewood, etc. It is not designed for lengthy use. If it is used for a lengthy period, the vibrations it causes in the hands of the user may result in circulation problems (white ﬁnger syndrome).The hand-arm vibration syndrome (vibration white ﬁnger) is a vascular disease that involves seizure-like spasms of the ﬁngers and toes. The affected areas are no longer sufﬁciently supplied with blood and therefore appear extremely pale. The frequent use of vibrating equipment may trigger nerve damage in people with an impaired circulation (for example smokers, diabetics).

CAUTION! Should you observe any unusual impairments, interrupt your work immediately and consult a doctor.

Proper Use

Customer Helpline 0151 649 1500

Page 17

Safety Information

Important - Please read these instructions fully before operating or maintaining

Safety Information

Follow these instructions in order to reduce the dangers:

Keep your body and in particular your hands warm when working in the cold.

Take regular breaks and move your hands to stimulate the blood circulation during the breaks.

Ensure that the equipment makes the least possible vibration through regular maintenance and solid parts on the equipment.

Kickback is the term used to describe the reaction of the chainsaw when the nose or tip of the guide bar comes into contact with an object. This form of contact causes a lightening fast reverse reaction causing the nose or tip of the chainsaw to ‘kickback’ towards the operator. This presents a risk of serious personal injury or even death. Although the chainsaw is ﬁtted with the various safety features, it is imperative that you stay alert at all times to prevent kickback occurring. You can do this by observing the following simple rules:

• Ensurethechainsawisheldrmlywithbothhands.Therighthandshouldgriptherearhandleand

the left hand the front handle. Gripping the handles ﬁrmly will help you control the chainsaw more effectively in the event of kickback.

• Ensurethetipornoseofthechainsawnevercomesintocontactwithanyobjectwhileoperating.

• Alwaysusethechainsawatfullthrottletomaintaintheoptimumcuttingspeed.

• Undernocircumstancesshouldyouoverreachwhileoperatingthechainsaw.

The following ﬁgure demonstrates the reaction zone of the chainsaw tip and situations which may cause kickback.

Kickback Safety

Proper Use (continued)

Direction of reaction

Reaction zone

1 2 1 1

Customer Helpline 0151 649 1500

Page 18

Safety Information

Important - Please read these instructions fully before operating or maintaining

Customer Helpline 0151 649 1500

Safety Information

Important - Please read these instructions fully before operating or maintaining

Pinching is the term used to describe the reaction of the chainsaw when the BOTTOM or TOP of the guide bar is pinched in the object being cut or sawn. This form of contact causes the chainsaw to move rapidly towards or away from you. If the BOTTOM of the guide is pinched, the chainsaw will be pulled away from you. If the TOP of the guide is pinched, the chainsaw will be pushed towards you. This presents a risk of serious personal injury or even death. Although the chainsaw is ﬁtted with the various safety features, it is imperative that you stay alert at all times to prevent pinching occurring.

To prevent pinching, always place the object to be cut against the claw stop at the rear of the guide bar as shown in the ﬁgure below.

Pinching Safety

The following ﬁgure demonstrates the types of sawing action which may lead to pinching.

Push Reaction

Pull reaction

Page 19

Customer Helpline 0151 649 1500

Step 1 - Assembly of the Chain Saw

Step 2 - Check the Chain Brake

Preparing to Operate the Chainsaw

Please refer to the Assembly Instructions in the Assembly Manual for details of how to assemble the chainsaw.

Please refer to the Assembly Instructions in the Assembly Manual for details of how to adjust the tension of the Chain bar and Chain on the chain saw Main Body Assembly.

Please refer to the Assembly Instructions in the Assembly Manual for details of how to ﬁt the Chain bar and Chain to the chain saw Main Body Assembly.

2a and 2b

Disengaged Engaged

Page 20

Customer Helpline 0151 649 1500

WARNING! The chain brake must not be tested with the chainsaw running unless strictly instructed to do so in this manual. Failure to observe this warning may lead to serious personal injury.

WARNING! The chain brake can only reduce the possibility of serious personal injury if it is ﬁtted in accordance with the instructions detailed in the Assembly Manual. If the chain brake is tampered with or the chainsaw is not used in accordance with these operating instructions i.e. careless operation, the risk of serious injury may still exist.

CAUTION! If it proves difﬁcult to move the chain brake lever into the required position, stop using the chainsaw immediately. It should be inspected by a suitably qualiﬁed service technician.

The chainsaw is ﬁtted with a chain brake which is designed to reduce the possibility of serious personal injury due to kickback. The chain brake is engaged when pressure is applied to the chain brake lever i.e. when the operator’s hand strikes the chain brake lever during kickback.

Once the chain brake is engaged, the saw chain stops moving immediately.

WARNING! NEVER use a chainsaw which is damaged, incorrectly set or incompletely and loosely assembled. Failure to observe this warning may lead to serious personal injury.

Step 2 - Check the Chain Brake (continued)

Preparing to Operate the Chainsaw

The engine must be stopped before the following checks are carried out.

2a. Check the Chain Brake Disengages

Pull the chain brake lever

fully backwards until it ‘clicks’ into position. If the chain brake is

disengaged it should be possible to move the saw chain using a gloved hand.

If it is not possible to move the saw chain, the chain brake may be damaged. Do not use the chainsaw until it has been inspected by a suitably qualiﬁed technician.

2b. Check the Chain Brake Engages

Push the chain brake lever

fully forwards until it ‘clicks’ into position. If the chain brake is engaged it

should NOT be possible to move the saw chain using a gloved hand.

If it is possible to move the saw chain, the chain brake may be damaged. Do not use the chainsaw until it has been inspected by a suitably qualiﬁed technician.

Page 21

Customer Helpline 0151 649 1500

Preparing to Operate the Chainsaw

Step 2 - Fuel and Lubrication

2-cycle engine oil

Regular unleaded fuel

x 30 seconds

Page 22

Customer Helpline 0151 649 1500

It essential for the smooth operation of the chainsaw to use the correct type of fuel and oil. The chainsaw utilises a 2-stroke engine which runs on a mixture of regular unleaded fuel and 2-cycle engine oil mixed at a ratio of 40:1.

The chainsaw will operate with any brand or grade of regular unleaded fuel which is designed for automotive use.

3a. Filling the Mixing Container with Fuel and Oil

WARNING! Before attempting to mix fuel and oil, always ensure all sources of ignition are removed

i.e. naked ﬂames.

WARNING! The chainsaw should NOT be used with petrol only. This will cause permanent damage to the engine and will void your warranty.

CAUTION! Only use premium grade oil for 2-cycle air cooled engines designed to be mixed to a ratio of 40:1. Under no circumstances should oils designed for 100:1 mixes be used. Failure to observe this caution may prevent the engine from being suitable lubricated.

CAUTION! Using 2-cycle oils designed for mixing ratio other than 40:1 will void your warranty.

CAUTION! Do not use a fuel/oil mixture which has been stored for more than 90 days.

NOTE! It is recommended that a full container of fuel and oil is mixed every time to ensure the correct

mixing ratio is achieved.

Fill the supplied mixing container

with approximately 500 ml of regular unleaded fuel. This level

is indicated on the side of the container.

Add 2-cycle oil to the mixing container

to ﬁll up to the 40:1 oil indication . This requires 12.5 ml

of oil.

3b. Mixing Fuel and Oil

Ensuring the top of the mixing container

is ﬁtted and fully tightened, shake vigorously for

30 seconds.

Step 3 - Fuel and Lubrication (continued)

Preparing to Operate the Chainsaw

Page 23

Customer Helpline 0151 649 1500

Step 4 - Filling the Fuel Tank

Preparing to Operate the Chainsaw

4a. Fill the Fuel Tank

WARNING! Before attempting to ﬁll the fuel tank, always ensure all sources of ignition are removed i.e.

naked ﬂames.

Remove the fuel tank cap

by unscrewing anti-clockwise.

Remove the top of the mixing container

(shown in step 2) and position a suitable funnel (not

supplied) into the fuel tank. Pour the fuel and oil mixture into the fuel tank.

Reﬁt the fuel tank cap

and tighten by turning clockwise. Only tighten using your hands - DO NOT

use tools.

Page 24

Customer Helpline 0151 649 1500

Step 5 - Filling the Chain Lubrication Oil Tank

Preparing to Operate the Chainsaw

5a. Fill the Oil Tank

WARNING! Before attempting to ﬁll the oil tank, always ensure all sources of ignition are removed

i.e. naked ﬂames.

Remove the oil tank cap

by unscrewing anti-clockwise.

Fill the oil tank with the suitable oil designed for lubricating saw chains.

Reﬁt the oil tank cap

and tighten by turning clockwise. Only tighten using your hands -

DO NOT use tools.

NOTE! Please refer to the Maintenance Section - Step 6 for details of how to lubricate the chain /

chain bar.

Page 25

Customer Helpline 0151 649 1500

Step 1 - Starting the Engine

Operating the Chainsaw

1a . Set the Ignition Switch to STOP

Move the ignition switch

to the lower STOP (OFF, “0”) position.

1b. Ensure the Choke is Fully Out

Pull the choke lever

fully out until it clicks into position.

Page 26

Customer Helpline 0151 649 1500

Step 1 - Starting the Engine (continued)

Operating the Chainsaw

Step 1 - Starting the Engine (continued)

Operating the Chainsaw

Place the chainsaw on a ﬁrm level surface clear of debris or any objects which may come into contact with the saw chain while it is moving.

Place your right foot on the trigger plate

to keep the chainsaw stable while starting. Your left foot

should be positioned so that it is clear of the chainsaw but still allows you to stand ﬁrmly.

Grasp the handle

ﬁrmly with your left hand.

Using your right hand pull the starter cord

slowly towards you until you feel resistance.

Ensuring that all parts of your body are away from the saw chain, rapidly pull the starter cord

slowly

and release in a controlled manner four times.

The chainsaw is now primed.

IMPORTANT! Always pull the starter cable slowly until you feel the initial resistance before you then pull it quickly to start the engine. Do not allow the starter cable to whip back of it’s own accord.

1c. Priming the Chainsaw

WARNING! Before attempting to start and operate the chainsaw, ensure the saw chain is not in

contact with the ground or any other object. Failure to observe this warning may lead to kickback or objects being propelled towards you and others in the area.

WARNING! Never attempt to start or operate the chainsaw if you suspect there is spilt fuel or any other ﬂammable gases/liquids in the area. Failure to observe this notice may present a risk of explosion.

WARNING! Always be aware of the proximity of any part of your body to the saw chain while the operating the chainsaw. Ensure the saw chain is kept away from legs, feet and body at all times. Failure to observe this warning may lead to serious personal injury or death.

WARNING! Always wear fully enclosed safety goggles when operating the chainsaw to protect your eyes from ﬂying dust and debris. Failure to observe this warning may lead to irreparable damage to your eyes.

WARNING! Always wear suitable ear plugs or ear defenders when operating the chainsaw to protect your hearing. Prolonged exposure to the loud noise produced by the chainsaw may lead to hearing loss or impairment.

WARNING! Always wear suitable gloves when operating chainsaw to protect your hands from ﬂying debris and/or sharp objects. It is particularly important to wear protective gloves when assembling or maintaining the saw chain.

Ensure the chain brake is disengaged.

Page 27

Customer Helpline 0151 649 1500

1c . Priming the chainsaw

Push Primer Bulb 10 times.

Step 1 - Starting the Engine (continued)

Operating the Chainsaw

Page 28

Customer Helpline 0151 649 1500

Step 1 - Starting the Engine (continued)

Operating the Chainsaw

1d. Ensure the Choke is Fully In

Push the choke lever

fully in.

1e. Set the Ignition Switch to ON

Move the ignition switch

to the upper ON (“1”) position.

Page 29

Customer Helpline 0151 649 1500

Step 1 - Starting the Engine (continued)

Operating the Chainsaw

1f. Start the Chainsaw

WARNING! To stop the chainsaw in an emergency, apply rapid pressure to the chain brake and

stop switch.

Place the chainsaw on a ﬁrm level surface clear of debris or any objects which may come into contact with the saw chain while it is moving.

Place your right foot on the trigger plate

to keep the chainsaw stable while starting. Your left foot

should be positioned so that it is clear of the chainsaw but still allows you to stand ﬁrmly.

Grasp the handle

ﬁrmly with your left hand.

Using your right hand pull the starter cord

slowly towards you until you feel resistance.

Ensuring that all parts of your body are away from the saw chain, rapidly pull the starter cord

slowly and release in a controlled manner. Up to six pulls may be required to start the chainsaw. Allow the engine to idle for approximately 10 seconds.

NOTE! If the chainsaw fails to start repeat steps 1a to 1f. If the chainsaw still fails to start, consult the troubleshooting guide at the rear of this manual.

Page 30

Customer Helpline 0151 649 1500

Step 1 - Starting the Engine (continued)

Operating the Chainsaw

1g. Accelerate the Engine

WARNING! To stop the chainsaw in an emergency, rapidly strike the chain brake and stop switch.

Before attempting to saw anything with the chainsaw, the engine must be accelerated to operating speed. This is done using the throttle lever

. Once the chainsaw engine is running and has warmed

up, it is ready to use.

While fully depressing the safety lever

press the throttle lever

. The chainsaw engine will

rapidly accelerate.

Keep the throttle lever

depressed while sawing or cutting.

NOTE! It will not be possible to accelerate the chainsaw engine with the throttle lever unless the safety

lever is fully depressed. This is a safety feature.

1h. Stopping the Chainsaw

To stop the chainsaw, release the throttle lever

and move the ignition switch to the lower STOP

(OFF, “0”) position as shown in step 1a.

Only use the chainsaw as described in the following sections.

Page 31

Customer Helpline 0151 649 1500

Step 2 - Restarting the Chainsaw When Warmed Up

Operating the Chainsaw

2a. Restarting the Chainsaw When Warmed Up

NOTE! Once the chainsaw is warmed up there is no need to ‘prime the chainsaw’ as described in

step 1c.

Place the chainsaw on a ﬁrm level surface clear of debris or any objects which may come into contact with the saw chain while it is moving.

Ensure the ignition switch is set to the upper ON (“1”) position.

Place your right foot on the trigger plate

to keep the chainsaw stable while starting. Your left foot

should be positioned so that it is clear of the chainsaw but still allows you to stand ﬁrmly.

Grasp the handle

ﬁrmly with your left hand.

Using your right hand pull the starter cord

slowly towards you until you feel resistance.

Ensuring that all parts of your body are away from the saw chain, rapidly pull the starter cord

slowly and release in a controlled manner. Up to six pulls may be required to start the chainsaw.

Page 32

Customer Helpline 0151 649 1500

Introduction

How to Use the Chainsaw

WARNING! Before attempting to use the chainsaw, it is imperative that you undertake professional training by an accredited body. This will provide full instruction on the type of sawing and cutting operations that can be performed complete with relevant safety training.

Cutting and sawing with a chainsaw can be very dangerous if undertaken without proper training.

IMPORTANT! Hold the saw ﬁrmly with both hands. Place your right hand on the rear handle and your left hand on the front handle.

Noise emission complies with Directive 2000/14/EC.

This chainsaw can be used to perform the following types of cutting and sawing operations:

• Felling-Usedtocutdownlargetrees.

• Limbing-Usedtoremovebranchesandlargerlimbsfromatreetrunk.

• Bucking-Usedtocutlargelogsortrunksintosmallerlengths.

The following steps provide a brief overview of each type of cutting operation. Always undertake full professional training before using the chainsaw to perform any of these types of cuts.

Page 33

Customer Helpline 0151 649 1500

Felling

How to Use the Chainsaw

Felling is the type of cut used to cut down trees. Whereas it may be possible to cut down small trees (6-7 inches in diameter) with a single straight through cut, larger trees require a felling cut.

If this type of cut is made it is performed in two stages. The ﬁrst stage is the notching cut which determines the direction the tree will fall. The second stage is the felling cut which weakens the tree trunk and causes it to fall.

Felling Cut

Notching Cut

Direction of Fall

WARNING! A repeat path (A) should be planned and cleared as necessary before cuts are

started. The retreat path should extend back and diagonally to the rear of the expected line of fall, as illustrated above.

WARNING! If felling a tree on sloping ground, the chain saw operator should keep on the uphill side of the terrain, as the tree is likely to roll or slide downhill after it is felled.

NOTE! Direction of fall (B) is controlled by the notching cut. Before any cuts are made, consider the location of larger branches and natural lean of the tree to determine the way the tree will fall (1a).

Page 34

Customer Helpline 0151 649 1500

Felling (continued)

How to Use the Chainsaw

WARNING! Felling of trees is prohibited without the necessary training.

WARNING! Ensure that you frequently check the operation of the chainsaw Brake.

NOTE! ‘Stop claw’ is shown on page 4.

WARNING! Do not cut down a tree during high or changing winds or if there is a danger

to property. Consult a tree professional. Do not cut down a tree if there is danger of striking utility wires; notify the utility company before making any cuts.

WARNING! Never walk in front of a tree that has been notched. Make the felling cut (D) from the other side of the tree and 1.5-2.0 inches (3-5cm) above the edge of the notch (C). Never saw completely through the trunk. Always leave a hinge. The hinge guides the tree. If the trunk is completely cut through, control over the felling direction is lost.

Insert a wedge or felling lever in the cut well before the tree becomes unstable and starts to move. This will prevent the guidebar from binding in the felling cut if you have misjudged the falling direction. Make sure no bystanders have entered the range of the falling tree before you push it over.

WARNING! Before making the ﬁnal cut, always recheck the area for bystanders, animals or obstacles.

Page 35

Customer Helpline 0151 649 1500

How to Use the Chainsaw

Limbing

This type of cut is used to remove small branches from a felled or fallen tree. Cuts can be made horizontally or vertically to the bottom of a branch. Usually limbing cuts are performed when a tree trunk has been cut into small manageable lengths using a bucking cut. Branches under tension should be cut from the bottom up to avoid binding the chainsaw.

Page 36

Customer Helpline 0151 649 1500

Bucking

How to Use the Chainsaw

A bucking cut is used to cut a fallen or felled tree into small manageable lengths or logs. Usually the tree trunk will be supported at one end, both ends or along its entire length. Often this type of cut is performed using a sawhorse which provides all the required support to keep the trunk stable.

WARNING! Never cut tree limbs while standing on tree trunk.

Saw Horse

Page 37

Customer Helpline 0151 649 1500

Step 1 - Storing the Chainsaw for Short Periods

Storing the Chainsaw

The chainsaw can be stored for short periods of time (less than 30 days) without performing any storage maintenance. If the chainsaw is to be stored for longer than 30 days, carry out the storage maintenance instructions as described in the following section.

Before placing the chainsaw into storage, always carry out the following:

• Allowthechainsawenginetofullycool.

• Ensurethesawchainandguidebarareclean,freefromdebrisandfullylubricated.

• Coverthesawchainwiththesuppliedprotectivecover.

• Storethechainsawonatandlevelsurfacewiththechainsawupright.

• Storeinasafeplacewhichisnotaccessiblebychildrenorpeoplewhoarenotfamiliar

with its operation.

Store the unit in a dry place away from possible sources of ignition such as a furnace, gas hot water heater, gas dryer, etc.

If the chainsaw is to be placed into storage for more than 30 days, storage maintenance must be performed on the chainsaw. If the following steps are not carried out, when you next operate the chainsaw it may not start correctly and may need to be serviced.

2a. Access the Fuel Tank

Remove the fuel tank cap

by unscrewing anti-clockwise.

Step 2 - Storing the Chainsaw for Extended Periods

Page 38

Customer Helpline 0151 649 1500

Step 2 - Storing the Chainsaw for Extended Periods (continued)

Storing the Chainsaw

2b. Drain the Fuel Tank

WARNING! Always store excess fuel/oil mixtures drained from the fuel tank in a suitable sealed

container designed for the storage of ﬂ ammable liquids.

WARNING! Before attempting to mix fuel and oil, always ensure all sources of ignition are removed i.e. naked ﬂ ames.

Carefully lift and rotate the chainsaw so that the access hole to the fuel tank is facing downwards over a suitable funnel and container (not supplied).

Allow the excess fuel to drain into the funnel and container.

Page 39

Customer Helpline 0151 649 1500

Step 2 - Storing the Chainsaw for Extended Periods (continued)

Storing the Chainsaw

2c. Start the Chainsaw

Start the chainsaw as described on page 23 and allow it to run until it stops. This will ensure any fuel in the carburettor is used.

2d. Oil the Combustion Chamber

Allow the engine to cool (approx. 5 minutes).

Remove the spark plug as described on page 42.

Carefully pour one teaspoon of clean unused 2-cycle oil into the combustion chamber.

Pull the starter cord several times to ensure the 2-cycle oil covers all the internal components.

Replace the spark plug as described page 42.

Before the chainsaw can be used following extended storage, the following procedures must be performed.

Store the unit in a dry place away from possible sources of ignition such as a furnace, gas hot water heater, gas dryer, etc.

3a. Remove the Spark Plug

Remove the spark plug as described page 37.

3b. Clear the Combustion Chamber

Pull the starter cord several times to ensure the 2-cycle oil is expelled from the combustion chamber.

3c. Check the Spark Plug Electrode Gap

Carefully clean the spark plug as described page 37 and ensure the electrode gap (approx. 0.6mm is correct).

3d. Reﬁt the Spark Plug

Reﬁt the spark plug as described page 42.

3e. Prepare the Chainsaw for Use

Prepare the chainsaw for use as described on page 15 to 20.

Step 3 - Preparing the Chainsaw for Use Following Storage

Page 40

Customer Helpline 0151 649 1500

Maintenance Schedule

Maintenance

Performing routine maintenance correctly on your chainsaw will ensure you get years of trouble free use.

Please keep this manual safe for future reference.

It is recommended that the following maintenance schedule is adhered to. This will ensure the chainsaw operates correctly and is safe to use.

Some maintenance procedures must be performed by suitably qualiﬁed service technicians. These are indicated by the grey rows in the table.

Before each use

After 10 hours

After 50 hours

After 100 hours

After 300 hours

Check the chain brake



Check the air ﬁlter



Clean / replace the air ﬁlter

  (1)

Clean / replace the fuel ﬁlter

Visual inspection



Clean / replace the spark plug

 (2)

Lubricatetheguidebar



Reversing the guide bar



Check and adjust the carburettor throttle valve



Clean the cylinder head



Set the valve clearance



(1) Change the ﬁlter element if necessary.

(2) Gap 0.6mm. Replace as necessary.

Page 41

Customer Helpline 0151 649 1500

Step 1 - Operational Chain Brake Test

Maintenance

1a. Check the Chain Brake

WARNING! The chain brake can only reduce the possibility of serious personal injury if it is ﬁtted in

accordance with the instructions detailed in the Assembly Manual. If the chain brake is tampered with or the chainsaw is not used in accordance with these operating instructions i.e. careless operation, the risk of serious injury may still exist.

WARNING! If the chain brake fails the operational chain brake test, DO NOT use the chainsaw until it has been serviced and inspected by a suitably qualiﬁed technician.

CAUTION! If it proves difﬁcult to move the chain brake lever into the required position, stop using the chainsaw immediately. It should be inspected by a suitably qualiﬁed service technician.

NOTE! It is recommended that the operational chain brake test is performed following any maintenance procedures.

Place the chainsaw on a ﬁrm level surface clear of debris or any objects which may come into contact with the saw chain while it is moving.

Place your right foot on the trigger plate

to keep the chainsaw stable while starting. Your left foot

should be positioned so that it is clear of the chainsaw but still allows you to stand ﬁrmly.

Grasp the handle

ﬁrmly with your left hand.

Using your right hand pull the starter cord

(as shown in step 1f on page 20) slowly towards you

until you feel resistance.

Ensuring that all parts of your body are away from the saw chain, rapidly pull the starter cord

slowly and release in a controlled manner. Up to six pulls may be required to start the chainsaw.

Grasp the rear handle

with your right hand while depressing the safety lever M.

Apply a small amount of pressure to the throttle lever

. While the chainsaw engine accelerates,

apply pressure slowly and deliberately to the chain brake lever

The saw chain should STOP IMMEDIATELY. Release the throttle lever

Move the ignition switch

to the lower ‘STOP’ (lower) position.

Page 42

Customer Helpline 0151 649 1500

Step 2 - Clean / Replace the Air Filter

Maintenance

2a. Remove the Air Filter Cover

Unscrew the retaining cap

anti-clockwise.

NOTE! It is not possible to remove the retaining cap from the air ﬁlter cover. This is a captive component.

Carefully lift and remove the air ﬁlter cover

2b. Remove the Air Filter

Carefully lift the air ﬁlter

off the locating pin .

Page 43

Customer Helpline 0151 649 1500

Step 2 - Clean / Replace the Air Filter (continued)

Maintenance

2c. Clean the Air Filter

NOTE! If the air ﬁlter is being replaced, there is no need to perform this step.

Clean the air ﬁlter

using clean, warm soapy water. The air ﬁlter must be thoroughly rinsed and

air dried before reﬁtting it to the chainsaw.

2d. Reﬁt the Air Filter

Reﬁt the air ﬁlter

to the chainsaw ensuring it is correctly positioned over the locating pin .

Reﬁt the air ﬁlter cover

to the chainsaw ensuring it is correctly seated on all sides.

Tighten the retaining cap

by turning clockwise. Do not over tighten the retaining cap as this

may cause damage to the air ﬁlter cover

and retaining cap .

Page 44

Customer Helpline 0151 649 1500

Step 3 - Change / Replace the Fuel Filter

Maintenance

3a. Access the Fuel Tank

Remove the fuel tank cap

by unscrewing anti-clockwise.

Drain the fuel tank as described in step 2b on page 29.

3b. Remove the Fuel Filter

Using a piece of wire, for example a paper clip, form a long hook.

Use the hook to move the fuel ﬁlter

towards the front of fuel tank.

Using your ﬁngers, carefully withdraw the fuel ﬁlter

from the fuel tank.

Page 45

Customer Helpline 0151 649 1500

Step 3 - Change / Replace the Fuel Filter (continued)

Maintenance

3c. Separate the Fuel Filter

Carefully pull the fuel ﬁlter

off the fuel pipe using a twisting action.

3d. Clean the Fuel Filter

NOTE! If the fuel ﬁlter is being replaced, there is no need to perform this step.

Clean the fuel ﬁlter

using clean, warm soapy water. The fuel ﬁlter must be thoroughly rinsed and

air dried before reﬁtting it to the chainsaw.

Page 46

Customer Helpline 0151 649 1500

Step 3 - Change / Replace the Fuel Filter (continued)

Maintenance

3e. Reﬁt the Fuel Filter

Carefully ﬁt the cleaned or replacement fuel ﬁlter

to the fuel pipe .

Position the fuel ﬁlter

in the lower corner of the fuel tank. You may need to use a

screwdriver to position the fuel ﬁlter

correctly.

Reﬁll the fuel tank with a new mixture and replace the fuel cap as described in Step 3a on page 14.

4a. Set the Ignition Switch to STOP

Move the ignition switch

to the lower STOP (OFF, “0”) position.

Step 4 - Clean / Replace the Spark Plug

Page 47

Customer Helpline 0151 649 1500

Step 4 - Clean / Replace the Spark Plug (continued)

Maintenance

4b. Remove the Air Filter Cover

Unscrew the retaining cap

anti-clockwise.

NOTE! It is not possible to remove the retaining cap from the air ﬁlter cover. This is a captive

component.

Carefully lift and remove the air ﬁlter cover

Page 48

Customer Helpline 0151 649 1500

Step 4 - Clean / Replace the Spark Plug (continued)

Maintenance

4c. Remove the Air Filter

Carefully lift the air ﬁlter

off the locating pin .

4d. Disconnect the Ignition Cable

Remove the ignition cable

from the spark plug by pulling backwards using a twisting action.

Page 49

Customer Helpline 0151 649 1500

Step 4 - Clean / Replace the Spark Plug (continued)

Maintenance

4e. Remove the Spark Plug

CAUTION! Only use the large end of the supplied multi tool to remove the spark plug. Using any other

tool may damage the spark plug and/or the chainsaw engine.

Remove the spark plug

from the chainsaw engine using the large end of the supplied multi tool.

Page 50

Customer Helpline 0151 649 1500

Step 4 - Clean / Replace the Spark Plug (continued)

Maintenance

4f. Reﬁt the Spark Plug

CAUTION! Only use the large end of the supplied multi tool to remove the spark plug. Using any other

tool may damage the spark plug and/or the chainsaw engine.

NOTE! If the spark plug is not being replaced, clean the existing spark plug with a copper wire brush and check the electrode gap using suitable feeler gauges. The gap must be 0.6 mm.

Reﬁt the spark plug

to the chainsaw engine using the large end of the supplied multi tool. Do Not

overtighten the spark plug.

Reﬁt the ignition cable

to the spark plug

Ensure the ignition cable is fully seated on the end of

the spark plug

Reﬁt the air ﬁlter

to the chainsaw ensuring it is correctly positioned over the locating pin .

Reﬁt the air ﬁlter cover

to the chainsaw ensuring it is correctly seated on all sides.

Tighten the retaining cap

by turning clockwise. Do not over tighten the retaining cap as this

may cause damage to the air ﬁlter cover

and retaining cap .

Page 51

Customer Helpline 0151 649 1500

Step 5 - Carburettor Settings

Step 6 - Lubricating the Sprocket Tips

Maintenance

The carburettor is factory set to the ideal setting for the chainsaw to operate efﬁciently. If the carburettor requires adjustment after extensive use, contact a suitably qualiﬁed service technician to inspect the chainsaw and make the necessary adjustments.

6a - Set the Ignition Switch to STOP

Move the ignition switch

to the ‘STOP’ (lower) position.

Page 52

Customer Helpline 0151 649 1500

Step 6 - Lubricating the Sprocket Tips (continued)

Maintenance

6b. Lubricating the Sprocket Tips

WARNING! Always wear suitable gloves when operating chainsaw to protect your hands from ﬂying debris and/

or sharp objects. It is particularly important to wear protective gloves when assembling or maintaining the saw chain.

NOTE! To lubricate the guide bar you will need a suitable grease gun with a long thin needle nose (not supplied). This is not supplied with the chainsaw and must be sourced from a suitable supplier.

NOTE! The guide bar sprocket tips can be lubricated without disassembling the chainsaw.

Using a wire brush, remove any debris from both the saw chain

and guide bar .

Insert the nose of the grease gun

into the upper lubricating hole of the guide bar . Pump grease into the

lubricating hole until excess grease appears on the edge of the sprocket tip.

Using a gloved hand, slowly rotate the saw chain until the next sprocket tip is exposed.

Repeat the greasing procedure described above. Keep rotating and greasing the sprocket tips until they

are all

fully greased.

Page 53

Customer Helpline 0151 649 1500

Step 7 - Reversing the Guide Bar

Step 8 - Adjusting the Automatic Chain Lubricator

Maintenance

7a. Remove the Guide Bar

The guide bar must be completely removed from the chainsaw. To do this, reverse the procedures described in the assembly manual.

7b. Clean the Guide Bar

NOTE! To clean the guide bar, you will need a bar scraper. This is not supplied with the chainsaw and

must be sourced from a suitable supplier.

Using a bar scraper

, remove any trapped debris from the grooves at the top and bottom of the

guide bar

If necessary remove any burrs or sharp edges using a ﬂat ﬁle.

7c. Reverse the Guide Bar

Reﬁt the guide bar

to the chainsaw as described in the assembly manual. Take care to ensure that

the guide bar is inverted before reassembling.

The automatic chain lubricator is factory set to the ideal setting for the chainsaw to operate efﬁciently. If the automatic chain lubricator requires adjustment after extensive use, contact a suitably qualiﬁed service technician to inspect the chainsaw and make the necessary adjustments.

Page 54

Customer Helpline 0151 649 1500

Step 9 - Check the Saw Chain Tension

Maintenance

9a. Check the Saw Chain Tension

CAUTION! It is essential that the correct saw chain tension is maintained. This will ensure that the saw

chain

, drive sprocket, guide bar and engine do not wear prematurely.

Using a screwdriver, turn the tension adjustment screw

clockwise or anti-clockwise to adjust the

saw chain

tension.

Turn the tension adjustment screw

anticlockwise to decrease the tension.

Turn the tension adjustment screw

clockwise to increase the tension.

The saw chain must ﬁt snugly all the way around the guide bar

as shown.

Using a gloved hand, ensure the saw chain

is free to move. If the saw chain does not move,

decrease the tension.

Page 55

Customer Helpline 0151 649 1500

Step 10 - Sharpening the Saw Chain

Maintenance

If the cutting performance of the chainsaw deteriorates, the saw chain may need sharpening or replacing. Please contact the customer helpline for support.

Check the Ignition

Switch is in the

‘ON’ position.

If No, then set the

Ignition Switch to

the ‘ON’ position.

Continue with the

starting procedure.

Continue with the

starting procedure.

Pull the Starter

Cord a minimum of

6 times.

If yes, check there is

sufﬁcient fuel in the

fuel tank.

If No, then ﬁll the

fuel tank with

sufﬁcient fuel.

Ensure the correct

mixture.

If the chainsaw still fails to start and if after trying all of the above, please call the

helpline for further assistance.

General Troubleshooting

Page 56

Customer Helpline 0151 649 1500

The following table provides solutions to common problems encountered with the chainsaw.

Fault Possible Cause Solution

Chainsaw will not start or starts but will not run.

The chainsaw has not been started correctly.

Start the chainsaw as

described on page 21. The carburettor setting is incorrect.

Please contact the

Customer Helpline on

0151 649 1500 The spark plug is fouled. Inspect the spark plug

electrode gap using suitable

feeler gauges as described

on page 42. Alternatively

clean the spark plug using

a wire brush (not supplied). The fuel ﬁlter clogged. Clean or replace the

fuel ﬁlter as describe on

page 40. The chain brake is engaged. Disengage the chain brake

as described on page 15.

The chainsaw starts but the power levels are low.

The air ﬁlter is dirty. Clean or replace the air ﬁlter

as describe on page 38. The carburettor setting is incorrect.

Please contact the

Customer Helpline on

0151 649 1500.

The chainsaw engine hesitates. The carburettor setting

is incorrect.

Please contact the

Customer Helpline on

0151 649 1500.

The chainsaw power levels are low when sawing or cutting.

The spark plug is fouled. Inspect the spark plug

electrode gap using suitable

feeler gauges as described

on page 42. Alternatively

clean the spark plug using

a copper wire brush

(not supplied).

The chainsaw runs inconsistently The carburettor setting is

incorrect.

Please contact the

Customer Helpline on

0151 649 1500

The chainsaw produces excessive smoke while running.

The fuel and oil mixture is incorrect.

Ensure the fuel mixture is

correct as described on

page 17.

Page 57

Customer Helpline 0151 649 1500

Useful Information

Type of Machine HS-CS 37/1 Article Number of Machine 4501642 Identiﬁcation Number of Machine 11011

Fault Possible Cause Solution

The chainsaw fails to cut or saw correctly.

The saw chain is blunt. Please contact the

Customer Helpline on

0151 649 1500 The saw chain is loose. Adjust the saw chain

tension as described

on page 50.

The chainsaw engine stops abruptly.

The fuel tank is empty. Fill up the fuel tank as

described on page 19. The fuel ﬁlter is located incorrectly in the fuel tank.

Ensure the fuel ﬁlter is

positioned correctly in

the fuel tank as described

on page 40.

The saw chain and guide bar become excessively hot and discoloured during use.

There is insufﬁcient lubrication due to an empty oil tank.

Reﬁll the oil tank as

described on page 20.

The oil lubrication openings are blocked.

Clean the guide bar as

described on page 49.

Manufacturer:ISCGmbH,InternationalServiceCenter,Eschenstraße6,94405,Landau/Isar,Germany

Page 58

Customer Helpline 0151 649 1500

Technical Data Table

Technical Data

Property Value

Engine displacement 37.2 cm

Maximum engine capacity 1.2 kW

Cutting length 37 cm

Guide bar length 16” (40 cm)

Chain pitch (3/8”) 10 mm

Chain thickness (0.05”) 1.27 mm

Idling speed 3200 min

-1

Maximum speed with cutting equipment 11,000 min

-1

Tank capacity 310 ml

Oil tank capacity 210 ml

Anti-vibration function Yes

Chain wheel teeth 6 x 9.525 mm

Chain brake Yes

Clutch Yes

Automatic chain lubrication Yes

Low-kickbackchain Yes

Net weight without chain and chain bar 4.55 kg

Net weight (dry) 5.22 kg

Fuel consumption (speciﬁc) 560 g / kWh

LpAsoundpressurelevel 100 dB(A)

LWAsoundpowerlevel 112 dB(A)

Uncertainty KpA 2.5 dB(A)

Uncertainty Khv 1.5 m/s

Vibration ahv (front handle) max. 5.46 m/s

Vibration ahv (rear handle) max. 6.21 m/s

Chain type

OREGON (91PO57X)/

CARLTON(N1C-BL-57E-SKB)

Bar type

OREGON (160SDEA041)/ QIRUI (PO16-50SR)

Spark plug L8RTF

Disposal Instructions

Disposal

The chainsaw and its accessories are made of various recyclable materials. Dispose of the chainsaw in accordance with your local recycling regulations.

Page 59

Customer Helpline 0151 649 1500

Guarantee

Dear Customer,

In the unlikely event that your device develops a fault, please contact our Customer service department on the telephone number shown below.

1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. Claims must be accompanied by Proof of purchase. This must be in the form of a Sales receipt or Bank statement and must show that the product has been purchased within 2 years prior to the claim from the retailer that it was originally sold to.

2. Our guarantee covers problems caused by material or manufacturing defects, and will result in the repair of these defects or replacement of the device with a like for like or similar article. Please note that our devices have not been designed for use in commercial, trade or industrial applications or for other equivalent activities.

3. The following are also excluded from our guarantee:

• Faultsduetoaccidents,customermisuse,orunauthorisedrepairs.

• ConsumablePartssuchasBlades/Chains/Trimmerlines/Spools/VacuumBags/SparkPlugs

or Filters.

• Failureduetolackofroutinemaintenance.

• Failureasaresultofnotusingtheequipmentinaccordancewiththemanualandsafety

instructions.

• Theadjustmentorlubricationcables,drivebelts,orrecoilstarters.

4. The guarantee is valid for a period of 2 years starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts ﬁtted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts ﬁtted. This also applies when an on-site Service is used.

5. Please keep sales receipt in a safe place. If the defect is covered by our guarantee your device will either be repaired under the terms of guarantee or we will send you a replacement device.

Thisdevicemaybere-conditionedorLikeforlikereplacement.

UK/Ireland 0151 649 1500 Republic of Ireland 1890 946 244 Web www.einhell.co.uk

Home Retail Group 489-499 Avebury Boulevard, Saxon Gate West, Central Milton Keynes MK9 2NW

After Sales Support

Page 60

Customer Helpline 0151 649 1500

Declaration of Conformity