SOUTHWESTSOLUTIONSGROUP Library Shelving Installation Instructions Manual
LIBRARY
SHELVING
INSTALLATION INSTRUCTIONS
www.southwestsolutions.com
www.southwestsolutions.com
Major Components Identification
Mobile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Contents
Hardware Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pre-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation
Single Face Mobile Units . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Double Face Mobile Units . . . . . . . . . . . . . . . . . . . . . . . . . 8
Single Face Static Units . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Double Face Static Units . . . . . . . . . . . . . . . . . . . . . . . . . 12
Adjustable Shelves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Base Shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1
Major Components Identification / Mobile
G
F
A
B
C
D
E
NOTE:
• Variable catalog number designators h = frame height, w = frame width, d = shelf depth
• Catalog number designators L = left, R = Right
DESCRIPTION CATALOG NO.
A—WELDED FRAME CWF-hw
B—SLOTTED BACKSTOP CSBS-w
C—SLOTTED ADJUSTABLE SHELF (Includes backstop) CSSB-wd
D—DIVIDER CFD-d
E—PLAIN ADJUSTABLE SHELF CSPB-wd
F—GUSSETED BASE SUPPORT - DOUBLE FACE CDBG-d
G—GUSSETED BASE SUPPORT - SINGLE FACE CSBG-dL or -dR
2
www.southwestsolutions.com
Major Components Identification / Static
I
H
A
B
C
D
E
F
G
NOTE:
• Variable catalog number designators h = frame height, w = frame width, d = shelf depth
• Catalog number designators L = left, R = Right
DESCRIPTION CATALOG NO.
A—WELDED FRAME CWF-hw
B—SLOTTED BACKSTOP CSBS-w
C—SLOTTED ADJUSTABLE SHELF (Includes backstop) CSSB-wd
D—DIVIDER CFD-d
E—PLAIN ADJUSTABLE SHELF CSPB-wd
F—SLOTTED BASE SHELF CBSSB-wd
G—PLAIN BASE SHELF CBSPB-wd
H—BASE SUPPORT - DOUBLE FACE CDB-d
I—BASE SUPPORT - SINGLE FACE CSB-dL or -dR
www.southwestsolutions.com
3
3/8 - 16 Self Retaining Nut
(Part No. 93048.01)
3/8 - 16 X 3/4 Gr. 5 Hex
(Part No. 95021.08)
3/8 - 16 Keps Nut
(Part No. 93015.08)
3/8 - 16 Appliance Leveler
(Part No. 950071.001)
9/16" I.D. X 2" O.D.
Spacer Washer
Hardware Identification
www.southwestsolutions.com
STATIC UNIT CANTILEVER FRAME
Bolt & Washer Requirements
Upright Base Foot Mid Bolt(s) Top Bolt Total Total
Height Bolts ONLY and Washers and Washer Bolts Washers
42” 2 1 1 4 2
66” 2 1 1 4 2
78” 2 1 1 4 2
84” 2 2 1 5 3
90” 2 2 1 5 3
NOTE: Mobile units require five bolts through gusseted base
support and one top bolt and washer.
Caution
All 3/8” hardware must be torque
tightened to 25-30 ft. lbs. for safe
installation.
4
www.southwestsolutions.com
Pre-Installation
Caution
Assembled shelving units must be
level for proper stability. Leveler
kits are optional and can be
ordered.
Special applications may require
shelving unit be floor-anchored or
wall-mounted for adequate stability.
Anchors are not provided as require-
Caution
ments vary. Wall attachment bracket
Before you begin installation:
1. Read through the installation procedure for your particular shelving unit.
2. Understand all CAUTION statements and apply them to your installation.
3. Make sure your shelving system will fit within the desired location.
4. Plan to assemble the shelving system where it will be used. Once fully
assembled, the unit may be difficult to move.
5. Have the necessary tools for assembling and leveling the unit.
(2-9/16” deep sockets) (2-3/8” drive rachet wrench)
(leveling devise) static only
(screwdriver)
A
kits (CWAB) are optional and can be
ordered.
Additional leveler
used on bases
with overall
support depths
over 10 inches
B
3/8 - 16 Self
Retaining Nut
If optional leveler kit is used, it is recommended the levelers be installed prior to
assembling the shelving units. Levelers are installed as follows:
1. Install self retaining nut in each square hole in bottom frame channel (A) and
base supports (B) as shown.
2. Fully thread the appliance levelers into the self retaining nuts.
3. Assemble the frames and base supports per the installation instructions.
4. Before assembling the base shelf, make sure the shelving unit is in the exact location it will be used. Use a flathead screwdriver to adjust the levelers so they contact
the floor surface.
5. Check the unit for proper level using a leveling device.
6. Using a flathead screwdriver, adjust the slotted leveler bolts up or down until unit
is level.
3/8 - 16 Appliance
Leveler
5
Loading...