Southwestern Bell 26963 User Manual
32-Channel 900 MHz
Call Waiting ID with Options
Cordless Telephone
26963
DIAL
MENU
DEL
1
GHI JKL
4
DROP & ANSWER
PQRS
7
TONE
*
RE/PA
CHANNEL
TALK
ABC
TELL BUSY
TUV
OPER
MEM
2
5
8
0
FLASH
FORM
PROG
MUTE
CONNECT ALL
DEF
3
ASK TO HOLD
MNO
6
TO CALL NOTES®
WXYZ
9
#
IN USE
CHARGE
PAGE
Southwestern Bell
FCC REGISTRATION INFORMATION
Your telephone equipment is registered with the Federal Communications Commission and is in compliance
with parts 15 and 68, FCC Rules and Regulations.
1 Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the FCC Registration number
and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this information
to your telephone company.
The REN is useful in determining the number of devices you may connect to your telephone line and still have
all of these devices ring when your telephone number is called. In most (but not all) areas, the sum of the
RENs of all devices connected to one line should not exceed 5. To be certain of the number of devices you may
connect to your line as determined by the REN, you should contact your local telephone company.
Notes
• This equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone
equipment if you are on a party line. Check with your local telephone company.
• Notice must be given to the telephone company upon permanent disconnection of your telephone from
your line.
2 Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone network, the telephone
company shall, where practicable, notify you that temporary discontinuance of service may be required.
Where prior notice is not practicable and the circumstances warrant such action, the telephone company may
temporarily discontinue service immediately. In case of such temporary discontinuance, the telephone
company must: (1) promptly notify you of such temporary discontinuance; (2) afford you the opportunity to
correct the situation; and (3) inform you of your right to bring a complaint to the Commission pursuant to
procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment, operations of
procedures where such action is required in the operation of its business and not inconsistent with FCC Rules
and Regulations. If these changes are expected to affect the use or performance of your telephone equipment,
the telephone company must give you adequate notice, in writing, to allow you to maintain uninterrupted service.
INTERFERENCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference; and (2) This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the
interference).
• Reorient or relocate and increase the separation between the telecommunications equipment and receiving
antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from that to which the
receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/
television technician for additional suggestions. Also, the Federal Communications Commission has
prepared a helpful booklet, “How To Identify and Resolve Radio/TV Interference Problems.” This booklet is
available from the U.S. Government Printing Office, Washington, D.C. 20402. Please specify stock number
004-000-00345-4 when ordering copies.
HEARING AID COMPATIBILITY
This telephone system meets FCC standards for Hearing Aid Compatiblility.
2
FCC NUMBER IS LOCATED ON THE CABINET BOTTOM
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
TABLE OF CONTENTS
FCC REGISTRATION INFORMATION .... 2
NTERFERENCE INFORMATION............ 2
I
EARING AID COMPATIBILITY ........... 2
H
INTRODUCTION ..................................... 5
ALLER ID ................................... 5
C
ALL WAITING.............................. 5
C
CALL WAITING ID ......................... 5
ALL WAITING ID OPTIONS ............ 5
C
OICE MESSAGING ........................ 5
V
GETTING STARTED ................................ 6
EFORE YOU BEGIN .......................... 6
B
ODULAR JACK REQUIREMENTS ...... 6
M
DIGITAL SECURITY SYSTEM ............. 6
NSTALLATION ....................................... 7
I
ESKTOP INSTALLATION ...................... 7
D
WALL MOUNT INSTALLATION .............. 8
ETUP .............................................. 10
S
ETTING THE AREA CODE................. 10
S
TONE/PULSE DIALING ...................... 11
ONE ........................................ 11
T
ULSE ....................................... 11
P
SETTING THE RINGER SOUND............ 12
ORDLESS PHONE BASICS.................... 13
C
AKING A CALL ............................. 13
M
REDIAL ...................................... 13
ECEIVING A CALL .......................... 14
R
LASH ........................................... 14
F
VOLUME ........................................ 14
HANNEL BUTTON .......................... 15
C
INGER ......................................... 15
R
MUTE ........................................... 15
EMPORARY TONE .......................... 16
T
AGING THE HANDSET ..................... 17
P
VOICE MESSAGING ......................... 17
EMORY........................................... 18
M
TORING A NUMBER IN MEMORY... 18
S
ENTERING TEXT USING THE
NUMBER KEYS ........................ 19
HANGING A STORED NUMBER...... 20
C
STORING A PAUSE IN MEMORY ..... 20
ECEIVING AND STORING CALLS ........ 21
R
ALLER ID OPERATION ........................ 21
C
DELETING RECORDS ........................ 22
ELETING THE CURRENT RECORD ... 22
D
ELETING ALL RECORDS............... 23
D
DIALING A CALLER ID NUMBER......... 23
HANGING THE NUMBER FORMAT...... 23
C
ALLER ID DISPLAY ........................ 24
C
CALL WAITING ID OPTIONS ............. 25
O CALL NOTES® ...................... 25
T
ELL BUSY ................................. 25
T
DROP & ANSWER ....................... 26
NSWER .................................... 26
A
SK TO HOLD ............................. 26
A
CONNECT ALL ............................ 27
OLD OPTIONS............................... 27
H
ETURN ..................................... 27
R
CONFERENCE .............................. 27
ROP ........................................ 28
D
ONFERENCE OPTIONS..................... 28
C
DROP FIRST................................ 28
ROP LAST ................................ 28
D
(Table of Contents continued
on the following page.)
WARNING: TO PREVENT FIRE
OR ELECTRICAL SHOCK HAZARD,
DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
THE LIGHTNING
FLASH AND ARROWHEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
"DANGEROUS
VOLTAGE" INSIDE
THE PRODUCT.
DO NOT OPEN
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER
(OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
3
HEADSET AND BELT CLIP OPERATION
(OPTIONAL)..................................... 29
CONNECTING A HEADSET TO THE
HANDSET
ONNECTING THE BELT CLIP ............. 29
C
.................................... 29
TROUBLESHOOTING GUIDE ................... 30
ERVICE ............................................ 33
S
HANGING THE BATTERY...................... 34
C
BATTERY SAFETY PRECAUTIONS..... 34
NDEX ............................................... 35
I
CCESSORY ORDER FORM ................... 37
A
4
INTRODUCTION
Your 900 MHz Cordless Telephone is designed to give you flexibility in use
and high quality performance. To get the most from your new cordless
telephone, we suggest that you take a few minutes right now to read
through this instruction manual.
IMPORTANT: Because cordless phones operate on electricity, you should have at
least one phone in your home that is not cordless, in case the power in your home
goes out.
CALLER ID
This feature allows you to see either the caller's number or the caller's
name and number before you answer the phone.
CALL WAITING
This feature allows you to answer incoming calls while you talk on the
phone.
CALL WAITING ID
This feature, known as Type II Caller ID, allows you to see the name and
phone number associated with an incoming call while you talk on the
phone.
CALL WAITING ID OPTIONS
This advanced Call Waiting feature allows you more options when
answering a call as you talk on the phone, including forward,
announcement, drop, answer, hold, and conference.
VOICE MESSAGING
This feature requires a subscription with your local phone company. It
allows callers to leave messages while you talk on the phone or if you are
unable to answer the call. The Voice Message Indicator blinks to indicate a
waiting message.
5
GETTING STARTED
Make sure your package includes the items shown here.
DIAL
FORM
TALK
PROG
MENU
DEL
MUTE
RE/PA
IN USE
IN USE
CHARGE
VOICE MAIL
PAGE
MEM
CONNECT ALL
ABC
DEF
2
3
1
ASK TO HOLD
GHI JKL
MNO
4
5
6
TO CALL NOTES®
DROP & ANSWER
TELL BUSY
PQRS
TUV
WXYZ
9
8
7
TONE
OPER
#
0
*
FLASH
CHANNEL
Mounting bracket
Base
Handset
BEFORE YOU BEGIN
MODULAR JACK REQUIREMENTS
You need an RJ11 type modular jack, which is the most
common type of phone jack and might look like the one
pictured here. If you don’t have a modular jack, call your
local phone company to find out how to get one installed.
DIGITAL SECURITY SYSTEM
Your cordless phone uses a digital security system to provide protection
against false ringing, unauthorized access, and charges to your phone line.
When you place the handset in the base, the unit verifies its security code.
After a power outage, you should place the handset in the base for about
30 seconds to reset the code.
INSTALLATION NOTE: Some cordless telephones operate at frequencies that
may cause interference to nearby TVs and VCRs. To minimize or prevent such
interference, the base of the cordless telephone should not be placed near or on
top of a TV or VCR. If interference continues, moving the cordless telephone
farther away from the TV or VCR will often reduce or eliminate the interference.
AC power supply
Telephone line cord
6
INSTALLATION
3
2
6
4
5
1
DESKTOP INSTALLATION
1. Make sure mounting bracket is securely fastened.
2. Set RINGER switch (on the handset) to ON.
3. Plug the power supply cord into the POWER 9V DC jack on the base and
into an AC outlet.
4. Place handset in the base to charge for 12 hours. The CHARGE light (on
the base) comes on to indicate that the battery is charging. If you don’t
charge the handset battery properly (for 12 hours) when you
first set up the phone, performance of the battery will be
compromised.
5. Plug the telephone line cord into the TEL LINE jack on the base and into
a modular jack.
6. Raise the base antenna.
NOTE : The phone automatically defaults to touch-tone dialing. To change to
pulse (rotary) dialing, see “Tone/Pulse Dialing”. If you don’t know which type
of service you have, check with the phone company.
CAUTION: Use only the Thomson 5-4081 power supply that is compatible
with this unit. Using other power supplies may damage the unit.
7
WALL MOUNT INSTALLATION
Because it is necessary to charge
the handset for 12 hours prior to
connecting the phone for use the
first time, it is better to leave the
unit on a flat surface during initial
charge before attempting to hang it
on the wall.
1. Make sure the mounting bracket
is securely fastened.
2. Set RINGER switch to ON.
3. Place the handset in the base.
4. Connect the power supply cord
into the base and the other end
into an AC outlet. The CHARGE
light comes on, indicating the
battery is charging.
Allow the phone to charge
for 12 hours before using the
first time. If you don't
charge the phone properly
when you first set up the
phone, performance of the
battery will be compromised.
(Installation continued on the
following page.)
2
3
4
1
CAUTION: Use only the Thomson
5-4081 power supply that came with
this unit. Using other power
supplies may damage the unit.
8
5. Remove the mounting bracket.
Rotate it so that the bottom of
the phone is flat. Reattach the
mounting bracket by inserting
the tabs into the slots on the top
of the unit first, and then
snapping the bottom tabs into
place.
6. Plug the short telephone line
cord into the jack marked TEL
LINE on the back of the unit and
plug the other end into a
modular wall jack.
7. Slip the mounting holes over
the wall plate posts and slide
the unit down firmly into place.
(Wall plate not included.)
8. Remove the handset hook; turn
it upside down, and put it back
in the slot. You need to do this
so the handset doesn’t fall out
of the base.
9. Raise the base antenna.
NOTE : The phone automatically
defaults to touch-tone dialing. To
change to pulse (rotary) dialing,
see “Tone/Pulse Dialing”. If you
don’t know which type of service
you have, check with the phone
company.
7
6
5
9
8
IN USE
IN USE
CHARGE
VOICE MAIL
PAGE
9
SETUP
SETTING THE AREA CODE
IMPORTANT: For proper Caller
ID operation, you must enter your
area code.
1. Make sure the phone is OFF.
2. Press the PROG button.
AREA CODE
shows on the
display.
3. Enter your 3-digit area code
using the number keys.
4. Press PROG to confirm.
ENTER
DIAL
MENU
DEL
1
GHI JKL
4
DROP & ANSWER
PQRS
7
TONE
*
RE/PA
CHANNEL
TALK
ABC
2
5
TELL BUSY
TUV
8
OPER
0
MEM
FLASH
FORM
PROG
MUTE
CONNECT ALL
DEF
3
ASK TO HOLD
MNO
6
TO CALL NOTES®
WXYZ
9
#
PROG
button
10
TONE/PULSE DIALING
This adjustment allows you to select
tone (touch-tone) or pulse (rotary)
mode dialing. The phone is automatically set for touch-tone use.
TONE
1. Make sure the phone is OFF.
2. Press and release the PROG
button until
on the display.
3. Press TONE*.
shows on the display.
4. Press PROG to confirm.
PULSE
1. Make sure the phone is OFF.
2. Press and release the PROG
button until
on the display.
3. Press #.
the display.
4. Press PROG to confirm.
TONE MODE
TONE MODE
PULSE MODE
PULSE MODE
shows
shows
shows on
TONE
button
DIAL
MENU
DEL
1
GHI JKL
4
DROP & ANSWER
PQRS
7
TONE
*
RE/PA
CHANNEL
TALK
ABC
2
5
TELL BUSY
TUV
8
OPER
0
MEM
FLASH
FORM
PROG
MUTE
CONNECT ALL
DEF
3
ASK TO HOLD
MNO
6
TO CALL NOTES®
WXYZ
9
#
PROG
button
11
SETTING THE RINGER SOUND
1. Make sure the phone is OFF.
2. Press and release PROG/MUTE
until
RINGER SETTING
the display.
3. Press 1 or 2 for the different
ringer sounds.
4. Press PROG/MUTE to confirm.
NOTE: You can exit the Program
mode at any time by pressing
PROG/MUTE.
shows on
12
DIAL
MENU
DEL
1
GHI JKL
4
DROP & ANSWER
PQRS
7
TONE
*
RE/PA
CHANNEL
TALK
ABC
2
5
TELL BUSY
TUV
8
OPER
0
MEM
TO CALL NOTES®
FLASH
FORM
PROG
MUTE
CONNECT ALL
DEF
3
ASK TO HOLD
MNO
6
WXYZ
9
#
PROG/
MUTE
button
CORDLESS PHONE BASICS
Allow the phone to charge for 12
hours before using the first time.
If you don't charge the phone
properly when you first set up
the phone, performance of the
battery will be compromised.
MAKING A CALL
The only two things you need to
know to make a call are:
• Press the TALK button before
you dial.
• Press TALK or place the handset
in the base to hang up.
REDIAL
Press the TALK button, then press
the REDIAL button to redial the last
number you called (up to 24 digits).
IMPORTANT: Because cordless
phones operate on electricity, you
should have at least one phone in your
home that is not cordless, in case the
power in your home goes out.
TALK
button
REDIAL
button
DIAL
MENU
DEL
1
GHI JKL
4
DROP & ANSWER
PQRS
7
TONE
*
RE/PA
CHANNEL
TALK
ABC
2
5
TELL BUSY
TUV
8
OPER
0
MEM
FLASH
FORM
PROG
MUTE
CONNECT ALL
DEF
3
ASK TO HOLD
MNO
6
TO CALL NOTES®
WXYZ
9
#
13
RECEIVING A CALL
To answer a call, pick up the handset
and press the TALK button.
FLASH
Use the FLASH button to activate
custom calling services such as call
waiting or call transfer, which are
available through your local phone
company.
IMPORTANT: If you press the
TALK button to activate custom
calling services such as call waiting,
you’ll hang up the phone. Press
FLASH instead.
VOLUME
The VOLUME buttons control the
volume of the handset's earpiece
and can be adjusted to 5 levels.
TALK
button
VOLUME
buttons
DIAL
MENU
DEL
1
GHI JKL
4
DROP & ANSWER
PQRS
7
TONE
*
RE/PA
CHANNEL
TALK
ABC
2
5
TELL BUSY
TUV
8
OPER
0
MEM
TO CALL NOTES®
FLASH
FORM
PROG
MUTE
CONNECT ALL
DEF
3
ASK TO HOLD
MNO
6
WXYZ
9
#
FLASH
button
14
CHANNEL BUTTON
If you ever experience any interference
or don’t have clear voice quality, press
the CHANNEL button on the handset
to advance to another channel.
RINGER
The handset RINGER switch can be
set to ON or OFF. If the switch is off,
the unit will not ring.
MUTE
To prevent the person you are
speaking to from hearing you while
on a call, press the PROG/MUTE
button.
Press PROG/MUTE again to cancel.
MUTE
shows in the display.
RINGER
switch
DIAL
MENU
DEL
1
GHI JKL
4
DROP & ANSWER
PQRS
7
TONE
*
RE/PA
CHANNEL
TALK
ABC
2
5
TELL BUSY
TUV
8
OPER
0
MEM
FLASH
FORM
PROG
MUTE
CONNECT ALL
DEF
3
ASK TO HOLD
MNO
6
TO CALL NOTES®
WXYZ
9
#
PROG/
MUTE
button
CHANNEL button
15
TEMPORARY TONE
This feature enables pulse (rotary)
service phone users to access
touch-tone services offered by
banks, credit card companies, etc.,
by pressing the TONE button to
temporarily make the phone touchtone compatible. To get information
about your bank account, for
example, you would:
1. Press the TALK button.
2. Call the bank’s information line.
3. Press the TONE button after your
call is answered.
4. Follow the voice instructions to
complete your transaction.
5. Hang up when finished. The
phone returns to pulse (rotary)
service.
TALK
button
TONE
button
DIAL
MENU
DEL
1
GHI JKL
4
DROP & ANSWER
PQRS
7
TONE
*
RE/PA
CHANNEL
TALK
ABC
2
5
TELL BUSY
TUV
8
OPER
0
MEM
FLASH
FORM
PROG
MUTE
CONNECT ALL
DEF
3
ASK TO HOLD
MNO
6
TO CALL NOTES®
WXYZ
9
#
16
PAGING THE HANDSET
Press the PAGE button on the base to
locate a misplaced handset. When
you press the PAGE button, the
handset beeps for 2 minutes. To stop
paging, press PAGE again or press
TALK on the handset. If the handset
is being used, it is paged with a soft
tone.
VOICE MESSAGING
If you have subscribed to your
telephone company's voice
messaging service, the VOICE MAIL
indicator on the base unit flashes
when you have messages, and
stops flashing when you have
reviewed the messages.
IN USE
IN USE
CHARGE
VOICE MAIL
PAGE
PAGE
button
VOICE
MAIL
indicator
17
MEMORY
Store up to 9 numbers in memory
for quick dialing.
STORING A NUMBER IN MEMORY
The phone must be OFF.
1. Press the MEM button.
2. Press any number key (1-9) to set
that number location for future
storage.
3. Press the MEM button again
(
ENTER NAME
display).
4. Enter a name (up to 15
characters) that corresponds with
the stored number.
5. Press the MEM button again
ENTER NUMBER
the display.
6. Dial the number to be stored (up
to 24 digits, including pauses).
7. Press MEM again to store the
number and corresponding
name.
appears in the
will appear in
DIAL
MENU
DEL
1
GHI JKL
4
DROP & ANSWER
PQRS
7
TONE
*
RE/PA
CHANNEL
TALK
ABC
2
5
TELL BUSY
TUV
8
OPER
0
MEM
FLASH
FORM
PROG
MUTE
CONNECT ALL
DEF
3
ASK TO HOLD
MNO
6
TO CALL NOTES®
WXYZ
9
#
MEM
button
18
ENTERING TEXT USING THE NUMBER KEYS
Use the numbered keys to enter
text. Each key represents four
characters, including the letters on
the key faces. To select a character,
press the appropriate key until that
character appears in the highlighted
space of the display. When you
have found the desired character,
press FORM to select it and to
advance the cursor to the next
space. (You may monitor your
progress on the display.)
In addition to the letter characters
printed on each face, the following
characters are also available:
KEY CHARACTER(S)
1 [space] - * !
2 (
3 )
4 $
5 '
6 ;
8 ?
DIAL
MENU
DEL
1
GHI JKL
4
DROP & ANSWER
PQRS
7
TONE
*
RE/PA
CHANNEL
TALK
ABC
2
5
TELL BUSY
TUV
8
OPER
0
MEM
FLASH
FORM
PROG
MUTE
CONNECT ALL
DEF
3
ASK TO HOLD
MNO
6
TO CALL NOTES®
WXYZ
9
#
FORM
button
19
CHANGING A STORED NUMBER
Use the same procedure to change a
stored number as you do to store a
number— you're just replacing the
current information with new
information.
S
TORING A PAUSE IN MEMORY
Use the RE/PA button to insert a
delay into a dialing sequence which
you are entering into the memory
(for example, when you must dial 9
to get an outside line or when you
must enter codes to access a bank's
information line). If you need a
longer delay, press the RE/PA
button more times. Each pause
counts towards the 24-digit limit.
RE/PA
button
DIAL
MENU
DEL
1
GHI JKL
4
DROP & ANSWER
PQRS
7
TONE
*
RE/PA
CHANNEL
TALK
ABC
2
5
TELL BUSY
TUV
8
OPER
0
MEM
FLASH
FORM
PROG
MUTE
CONNECT ALL
DEF
3
ASK TO HOLD
MNO
6
TO CALL NOTES®
WXYZ
9
#
MEM
button
20
CALLER ID OPERATION
Your phone receives and displays
information transmitted by your
local phone company. This
information may include the date,
time, and caller's phone number, or
the date, time, and the caller's
name and phone number.
RECEIVING AND STORING CALLS
When you receive a call, the
information is transmitted by the
phone company to your Call
Waiting ID Telephone between the
first and second ring. You can
monitor the information as it
appears in the display and decide
whether to answer the call. If you
are not at home, your telephone
stores the information for you to
see when you return.
21
The Caller ID memory holds 40
names and numbers. When the
memory is full, only the most
recent calls are stored. The oldest
number stored in the memory is
deleted to make room for the
number of the newest call, which
will be designated as call number
40 in the Caller ID display. Use the
CID REVIEW buttons on the side of
the handset to review stored calls.
DELETING RECORDS
Use the DEL button to erase the
record currently shown in the
display or all records.
DELETING THE CURRENT RECORD
1. Press DEL. The display shows
DELETE?
2. Press DEL again to erase the
record.
CID
REVIEW
buttons
DEL button
DIAL
MENU
DEL
1
GHI JKL
4
DROP & ANSWER
PQRS
7
TONE
*
RE/PA
CHANNEL
TALK
ABC
2
5
TELL BUSY
TUV
8
OPER
0
MEM
TO CALL NOTES®
FLASH
FORM
PROG
MUTE
CONNECT ALL
DEF
3
ASK TO HOLD
MNO
6
WXYZ
9
#
22
DELETING ALL RECORDS
1. Press and hold DEL. The display
shows
DELETE ALL?
2. Press DEL again to erase all
records.
DIALING A CALLER ID NUMBER
When the stored number is
displayed, you may dial it by
pressing the DIAL button.
CHANGING THE NUMBER FORMAT
The FORM button lets you change
the format of the displayed number.
The available formats are as
follows.
7-digit 7-digit telephone
number.
10-digit 3-digit area code
+ 7-digit telephone
number.
11-digit long distance
code “1” + 3-digit
area code + 7-digit
telephone number.
CID
REVIEW
buttons
DIAL
button
DEL
button
DIAL
MENU
DEL
1
GHI JKL
4
DROP & ANSWER
PQRS
7
TONE
*
RE/PA
CHANNEL
TALK
ABC
2
5
TELL BUSY
TUV
8
OPER
0
MEM
FLASH
FORM
PROG
MUTE
CONNECT ALL
DEF
3
ASK TO HOLD
MNO
6
TO CALL NOTES®
WXYZ
9
#
FORM
button
23
Loading...