Southbend SCX-10S-6-10 User Manual

Two ComparTmenT ConveCTion

S

Teamer wiTh 2 KeTTleS wiTh

S

Team Coil operaTion

Job Item#

SPECIFICATIONS:

Shall be a Southbend Model _______________________, convection
steamer complete with (2) 6 gallon kettles or (1) 6 and (1)10 gallon kettle
on a modular boiler base operating on steam coil boiler base. The

steamer shall be constructed of satin nish stainless steel, type 304,
with a cooking chamber of one-piece, all-welded, type 316 stainless

steel and shall be

 SCX-2S, 14” W x 10.625” H x 21 D (355 mm x 270 mm x 533 mm).

 SCX-10S, 14” W x 17” H x 21 D (355 mm x 432 mm x 533 mm).

The doors shall have a removable inner liner of stainless steel with full

perimeter gasket seal, an outer liner of one-piece all welded stainless
steel, and a positive lock and seal mechanism with spring release. The

steamer shall be provided with removable stainless steel pan supports
and a stainless steel drip trough connected to drain in order to collect
condensate when door is opened.

Each compartment’s control housing shall be constructed of stainless

steel with a fully removable side access panel. The controls shall include

an illuminated on/off power switch. The timing of each compartment

shall be independently controlled by a pilot ready light, a pilot cooking

light and a 60 minute electric timer which sounds an audible signal

at the end of the cooking cycle. Steam ow to the chamber shall be
cut off when the door is opened during the cooking cycle and shall be

reactivated when the door is closed.
The cabinet base with steam coil boiler and controls shall be provided

with full perimeter painted angle frame, reinforced counter and boiler
mountings, hinged door(s) with magnetic latch and 6” (152 mm) stainless
steel legs with adjustable bullet feet on the front and adjustable anged
feet on the rear for securing to the oor.

Boiler controls shall include automatic water level control, pressure
gauge, water gauge glass, operating pressure control, safety high-limit
pressure control and safety relief valve. Unit comes standard with a split
water line, CSD-1 boiler code, “Y” - strainer, and automatic blowdown.
The unit shall be ASME code stamped and National Board registere,

c-CSA-us and NSF certied.

Model description

SCX-2S-6-6

SCX-2S-6-10

SCX-10S-6-6

SCX-10S-6-10

OPERATION SHALL BE BY:

Steam coil heated steam boiler operating at 9-11 psi (62-76 kPa).

The boiler shall be equipped for operation on incoming steam

pressure of 25-45 psi (170-310 kPa) and a ow of 200 lbs. (90

kg) per hour. The controls shall be equipped for operation on:

115 VAC, 1 Phase, 60 Hz

OPTIONAL ITEMS AT EXTRA COST:

220 VAC, 1 Phase, 50 Hz

Secondary low water cut-off (California Code)

Solid state digital controls

Stainless steel back on cabinet

Stainless steel frame

Adjustable front anged feet

Load compensating timers

Correctional package

ACCESSORIES:

Ball oat trap (BFT)

Spray and rinse assembly

6 pan steamer with

(2) 6 gallon kettles

6 pan steamer with (1) 6 gallon and

(1) 10 gallon kettle

10 pan steamer with

(2) 6 gallon kettles

10 pan steamer with (1) 6 gallon and

(1) 10 gallon kettle

pan capacity per coMpartMent

pan depth

1” 2-1/2” 4” 6”

6 3 2 1

10 5 3 2

Form SCX2-6-6 Rev 0 (January/2014)

www.yatesgd.com www.yatesgraphicdesign.com

Models:

SCX-2S-6-6 SCX-2S-6-10 SCX-10S-6-6 SCX-10S-6-10

Model a

SCX-2S-6-6 55.5 [1410] 930 lbs. [421]
SCX-2S-6-10 55.5 [1410] 970 lbs. [439]
SCX-10S-6-6 68.5 [1740] 1030 lbs. [467]

SCX-10S-6-10 68.5 [1740] 1070 lbs. [462]

shipping Weight

Min clearance

SIDES

BACK

0
0

SERVICE CONNECTIONS

– ELECTRICAL CONNECTION: 1/2” (13 mm) conduit connection to controls.

2 Amps per compartment or to be as specied on data plate.

– BOILER FEED WATER: 1/2” (13 mm) NPT at 25-50 PSI (170-345 kPa).

– CONDENSATE COLD WATER: 1/2” (13 mm) NPT at 25-50 PSI (170-345 kPa) (OPTIONAL)

– DRAIN: 2” (51 mm) IPS piped to open oor drain. No solid connection.

– HOT WATER: 3/8” (10 mm) O.D. tubing at 25-50 PSI (170-345 kPa).

– STEAM SUPPLY: 3/4” (19 mm) IPS for incoming steam at 40-50 PSI(276-345 kPa)*

– SINK DRAIN: 1-1/8” (29 mm) O.D. tubing.

s

* Pressure reducing valve is required if incoming pressure exceeds 50 PSI(345 kPa).

Water quality is the major factor affecting the performance of your appliance. If you are unsure of water quality, consult a local water
treatment specialist and have the water analyzed. Your water supply must be within these general guidelines:

Total dissolved solids ....................Less than 60 PPM

Total alkalinity ................................Less than 20 PPM

Silica ...............................................Less than 13 PPM

Chlorine .........................................Less than 1.5 PPM

pH Factor ......................................7.0 - 8.5

Water which fails to meet these standards should be treated by installation of water conditioner.

FAILURE OR MALFUNCTION OF THIS APPLIANCE DUE TO POOR WATER QUALITY IS NOT COVERED UNDER WARRANTY.
CONTACT SOUTHBEND FOR WATER QUALITY SOLUTIONS.

WATER QUALITY STATEMENT

Form SCX2-6-6 Rev 0 (January/2014)

INTENDED FOR COMMERCIAL USE ONLY.

NOT FOR HOUSEHOLD USE

1100 Old Honeycutt Road, Fuquay-Varina, NC 27526

[phone] www.southbendnc.com

.