Southbend SB1307 User Manual

Instruction Sheet

Model SB1307

High Precision 6" Lathe Chuck

Chucks are heavy! Get assistance when installing or removing the chuck from the lathe. Wear heavy duty leather boots for foot and toe protection, and keep hands and fingers away from all pinch points. Ignoring this warning can lead to a severe crushing injury or finger amputation!

Specifications

• OD Clamping Range ...0.32"-6.30" (8-160mm)

• ID Clamping Range ..2.17"-5.90" (55-150mm)

• Outer Diameter ........................6.57" (167mm)

• Maximum Chuck Key Torque .........58 ft/lbs*

• Maximum Jaw Gripping Force ....... 4721 lbs*

• Maximum Speed .............................2000 RPM

• Two-Piece Hardened Steel Jaws ............... Yes

• Plain Back Mounting .................................Yes

• Jaw Mounting Cap Screw Torque ......29 ft/lbs

• Grease Fitting Lubricated .........................Yes

• Cast-Iron Construction ..............................Yes

• Chuck Weight ......................................... 19 lbs

• Origin ................................................... Taiwan

* Maximum handle torque and gripping force

is given at full jaw and scroll gear engagement. If jaw and scroll gear are partially engaged, clamping force and gripping force is reduced.

Hardened steel jaws for durability and extreme clamping force and grip.

Designed for

up to

2000 RPM.

Universal plain-back mounting.

Figure 1. Features.

Grease fitting for

complete internal

lubrication.

Two-piece

jaws for speedy

internal/external

clamping changes.

Manufactured

with high-tech

German CNC

machinery.

Installation

1. UNPLUG THE MACHINE FROM POWER!

2. Mount the back plate on the spindle.

3. Accurately measure the inside of the back

relief bore on the chuck. This dimension is critical and should be ± 0.001''.

4. Face the back plate to true it. Make passes across the face until its entire surface has been cut.

If you need help with your new item, contact

us at: (360) 734-1540 • FAX: (360) 676-1075

5. Turn a shoulder into the face

0.001" to 0.002'' larger than the back relief bore diameter. Remember that this is a press ﬁt. Chamfer the corner a small amount to prevent any burrs when installing.

⁄8'' deep and

-1-

6. Set the chuck on the back plate, aligning the shoulder with the relief bore. Use a transfer punch to mark the back plate. If a transfer punch is not available, a drill bit of the same size as the mounting holes in the chuck can be used. Lightly tap on the bit, rotate it 90° and tap it again.

7. Remove the chuck from the back plate and center punch the marks. Drill and tap the holes for M10-1.5 threads.

8. Remove the back plate from the lathe, and place it in to a freezer for 30 minutes, and place the chuck in an oven at 100° F. for the same amount of time.

9. Put on insulated leather gloves and place the chuck on the back plate. Line up the mounting holes and thread in the cap screws supplied.

10. Snug the ﬁrst M10-1.5 cap screw, then alternate the cap screws across the chuck until you reach a ﬁnal torque of 53.5 ft/lbs. Alternating the tightening process insures the chuck will be pressed on straight. This step should be repeated until the back plate ﬁts snugly against the chuck. If the chuck ﬁts loosely on the back plate, or is crooked on the shoulder, it will be necessary to recut the back plate face and shoulder again. If you are also installing the chuck by threading the M10-1.5 hex bolts into the chuck from the back side of the mounting plate, repeat Step 9 on these bolts, but torque them to 30 ft/lbs.

Operation and Safety

• Chuck Key Safety: A chuck key left in the

chuck can become a dangerous projectile when the spindle is started. Always remove the chuck key after using it. Develop a habit of not taking your hand off of a chuck key unless it is away from the machine.

Disconnect Power: Disconnect the lathe

•

from power before installing and removing the chuck or doing any maintenance or adjustments. Accidental lathe startup can cause severe injury or death.

Secure Clamping: A thrown workpiece may

•

cause severe injury or even death. When swapping the chuck jaw positions, use a torque wrench to re-torque the M8-1.25 jaw mounting cap screws to 29 ft/lbs. When clamping a workpiece, maximum gripping force is attained at full jaw and scroll gear engagement. If jaw and scroll gear are partially engaged, clamping force is reduced.

Speed Rates: Operating the lathe where

•

maximum chuck speed is exceeded, or at too high of a speed for an unbalanced workpiece, can cause the workpiece to be thrown from the chuck. Always use the appropriate feed and speed rates. A thrown workpiece may cause severe injury or even death.

Large Chucks: Large chucks are very

•

heavy and difficult to grasp, which can lead to crushed fingers or hands if mishandled. Get assistance when installing or removing large chucks to reduce this risk. Protect your hands and the precision ground ways by using a chuck cradle or piece of plywood over the ways of the lathe when servicing chucks.

Safe Clearances: Often chuck jaws will

•

protrude past the diameter of the chuck and can contact a coolant nozzle, tooling, tool post, or saddle. Before starting the spindle, make sure the workpiece and the chuck jaws have adequate clearance by rotating it through its entire range of motion by hand.

Stopping Lathe By Hand: Stopping

•

the spindle by putting your hand on the workpiece or chuck creates an extreme risk of entanglement, impact, crushing, friction, or cutting hazards. Never attempt to slow or stop the lathe chuck by using your hand. Allow the spindle to come to a stop on its own or use the brake (if equipped).

Long Stock Safety: Long stock can whip

•

violently if not properly supported, causing serious impact injury and damage to the lathe. Reduce this risk by supporting any stock that extends from the chuck/headstock more than three times its own diameter. Always turn long stock at slow speeds.

-2-

+ 2 hidden pages