South Bend SB1126 User guide

18" X 40" VARIABLE-SPEED WOOD LATHE
MODEL SB1126
***Keep for Future Reference***
OWNER'S MANUAL
®
South Bend Tools
A Tradition of Excellence
© February, 2024 by South Bend Tools For Machines Mfd. Since 10/23
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to proper installation in a safe environment, personnel training and usage authorization, proper inspection and maintenance, manual availability and comprehension, application of safety devices, cutting/sanding/grinding tool integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage from negligence, improper training, machine modifications or misuse.
Lead from lead-based paints.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: Work in a well ventilated area, and work with approved safety equipment, such as a dust mask or respirator that is specially designed to filter out microscopic particles.
Table of Contents
INTRODUCTION
Identification Description of Controls & Components Product Specifications
SAFETY
Understanding Risks of Machinery Basic Machine Safety Additional Wood Lathe Safety
PREPARATION
Preparation Overview Required for Setup Power Supply Requirements Unpacking Inventory Hardware Recognition Chart Cleaning & Protecting Location Lifting & Moving Assembly Test Run
OPERATION
Operation Overview Stock Inspection & Requirements Adjusting Tailstock Installing/Removing Tailstock Center Installing/Removing Headstock Center Removing/Installing Faceplate Adjusting Tool Rest
...............................................................................8
............................................... 14
................................................. 17
................................................ 19
................................................ 20
..............................................................2
............................................ 3
................................ 6
................ 8
.................................. 8
.................... 10
.............................................................. 11
............................... 11
................................... 11
....................... 12
.............................................. 14
...................... 15
............................... 16
..................................... 18
................................................................... 22
.................................. 22
................ 23
.................................. 23
................... 26
.................................. 27
........... 4
.......... 24
........ 25
Changing Speed Range .............................. 28
Indexing Spindle Turning Faceplate Turning Outboard Turning Sanding/Finishing Selecting Turning Tools
ACCESSORIES
MAINTENANCE
Maintenance Schedule............................... 38
Cleaning Unpainted Cast Iron Lubrication Machine Storage
SERVICE
Replacing/Tensioning V-Belt Aligning Pulleys
TROUBLESHOOTING
ELECTRICAL
Electrical Safety Instructions Wiring Diagram Electrical Components
PARTS
Main Machine Labels
WARRANTY
................................................. 29
....................................... 30
.................................... 32
.................................... 33
................................... 34
............................ 35
............................................................. 36
............................................................. 38
................................................. 38
................................. 38
............................................. 38
...................................... 39
.......................................................................... 40
..................... 40
...................................... 42
................................................ 43
.................................................................. 46
..................... 46
....................................... 47
.............................. 48
............................................................................... 49
...................................................... 49
........................................ 52
.................................................................... 53
South Bend Tools
Model SB1126
We stand behind our machines. If you have any service questions, parts requests or general questions about your purchase, feel free to contact us.
South Bend Tools P.O. Box 2027 Bellingham, WA 98227 Phone: (360) 734-1540 Fax: (360) 676-1075 (International) Fax: (360) 734-1639 (USA Only) Email: sales@southbendtools.com
For your convenience, any updates to this manual will be available to download free of charge through our website at:
www.southbendtools.com
This manual helps the reader understand the machine, how to prepare it for operation, how to control it during operation, and how to keep it in good working condition. We assume the reader has a basic understanding of how to operate this type of machine, but that the reader is not familiar with the controls and adjustments of this specific model. As with all machinery of this nature, learning the nuances of operation is a process that happens through training and experience. If you are not an experienced operator of this type of machinery, read through this entire manual, then learn more from an experienced operator, schooling, or research before attempting operations. Following this advice will help you avoid serious personal injury and get the best results from your work.
We've made every effort to be accurate when documenting this machine. However, errors sometimes happen or the machine design changes after the documentation process—so exactly match your machine. contact our
We highly value customer feedback on our manuals. If you have a moment, please share your experience using this manual. What did you like about it? Is there anything you would change to make it better? Did it meet your expectations for clarity, professionalism, and ease-of-use?
South Bend Tools
C
P.O. Box 2027 Bellingham, WA 98227 Email: manuals@southbendtools.com
Scope of Manual
Manual Feedback
If a difference between the manual and machine leaves you in doubt,
customer service for clarification.

INTRODUCTION

For Machines Mfd. Since 10/23
the manual may not
/O Technical Documentation Manager
Updates
Customer Service
-2-
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
INTRODUCTION
Identification
SpindleSpindle
IndexingIndexing
PinPin
SpindleSpindle
SpeedSpeed
ReadoutReadout
POWERPOWER
SwitchSwitch
Spindle Spindle
Direction Direction
SwitchSwitch
STOPSTOP
ButtonButton
(1 of 2)(1 of 2)
Spindle Speed DialSpindle Speed Dial
STARTSTART ButtonButton
(1 of 2)(1 of 2)
MainMain
ControlControl
PanelPanel
Tool Rest BaseTool Rest Base
Tool RestTool Rest
Tool HolderTool Holder
BedBed
Adjustable FootAdjustable Foot
(1 of 6)(1 of 6)
QuillQuill
Secondary Control PanelSecondary Control Panel
TailstockTailstock
Bed ExtensionBed Extension
(Inboard)(Inboard)
Belt Access Belt Access
DoorDoor
FaceplateFaceplate
(1 of 2)(1 of 2)
*Shown With Optional*Shown With Optional
SB1129 Outboard Tool RestSB1129 Outboard Tool Rest
Bed ExtensionBed Extension
(Outboard)(Outboard)
For Your Own Safety Read Instruction Manual
Before Operating Lathe
a) Wear eye protection. b) Do not wear gloves, necktie, or loose clothing. c) Tighten all locks before operating. d) Rotate workpiece by hand before applying power. e) Rough out workpiece before installing on faceplate. f) Do not mount split workpiece or one containing knots. g) Use lowest speed when starting new workpiece.
-3-
South Bend Tools
Model SB1126
INTRODUCTION
For Machines Mfd. Since 10/23

Description of Controls & Components

Refer to the following figures and descriptions to become familiar with the basic controls and components used to operate this machine.
Main Controls
AA
GG
BB
CC
EE
FF
DD
E. STOP Button (1 of 2): Stops motor and
disables START button and speed controls while it remains depressed. Enable START button by turning STOP button clockwise until it pops out.
F. Spindle Direction Switch: Toggles spindle
direction between forward (FOR) and reverse (REV).
G. POWER Switch w/Disabling Key: Turns
power to machine ON or OFF. Remove yellow key to disable switch.
Tool Rest
HH
II
JJ
Figure 1. Main controls layout.
A. Spindle Indexing Pin: Locks spindle in place
for indexing operations. Pull pin out and turn right to unlock spindle. Turn pin left and seat in indexing hole to lock spindle.
B. Spindle Speed Dial: Adjusts spindle speed
from low to high within range governed by pulley belt position.
C. Spindle Speed Readout: Indicates spindle
speed in revolutions per minute (RPM).
— Alarm light above display indicates a VFD
fault when illuminated. To reset, press STOP button on main control panel and move POWER switch to OFF position.
— When illuminated, Ready light indicates
machine is connected to power and VFD is functioning normally.
KK
Figure 2. Tool rest & bed extension components.
H. Tool Rest: Provides stable platform for
cutting tools.
I. Tool Rest Lock Handle: Secures tool rest in
position.
J. Tool Rest Base Lock Lever: Secures tool rest
base in position along bed.
K. Tool Holder: Holds tooling and supporting
equipment.
D. START Button (1 of 2): Turns motor ON.
-4-
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
INTRODUCTION
Bed Extension
LL
Tailstock
OO
PP
NN
LL
MM
Figure 4. Tailstock controls.
M. Quill Lock Handle: Secures quill in position.
N. Quill: Holds centers or tooling. Can be moved
toward or away from spindle.
QQ
RR
Figure 3. Bed extension installed in inboard and
outboard positions (shown with optional SB1129).
L. Bed Extension: Can be installed on inboard
end of bed to support tool rest and tailstock, or outboard end for oversized turning operations.
Like all machinery there is a potential danger when operating this machine. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this machine with respect and caution to decrease the risk of operator injury. If normal safety precautions are overlooked or ignored, serious personal injury may occur.
O. START Button (1 of 2): Turns motor ON.
P. STOP Button (1 of 2): Stops motor and
disables START button and speed controls while it remains depressed. Enable START button by turning STOP button clockwise until it pops out.
Q. Tailstock Handwheel: Moves quill toward or
away from spindle.
R. Tailstock Lock Lever: Secures tailstock in
position along bed.
No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to do so could result in serious personal injury, damage to equipment, or poor work results.
-5-
South Bend Tools
Model SB1126
Model SB1126
18" x 40" Variable-Speed Wood Lathe
Product Dimensions
Weight............................................................................................................................................................. 420 lbs.
Width (side-to-side) x Depth (front-to-back) x Height......................................................... 69-1/2 x 23-1/2 x 50 in.
Footprint (Length x Width)........................................................................................................... 46-1/2 x 16-1/2 in.
Shipping Dimensions
Type.......................................................................................................................................................... Wood Crate
Content.......................................................................................................................................................... Machine
Weight............................................................................................................................................................. 615 lbs.
Length x Width x Height................................................................................................................... 52 x 30 x 54 in.
Must Ship Upright................................................................................................................................................ Yes
INTRODUCTION
For Machines Mfd. Since 10/23

Product Specifications

P.O. Box 2027, Bellingham, WA 98227 U.S.A.
PHONE: (360) 734-1540 •
www.southbendtools.com
© South Bend Tools
Electrical
Power Requirement......................................................................................................... 220V, Single-Phase, 60 Hz
Full-Load Current Rating.................................................................................................................................... 18A
Minimum Circuit Size.......................................................................................................................................... 20A
Connection Type..................................................................................................................................... Cord & Plug
Power Cord Included............................................................................................................................................. Yes
Power Cord Length............................................................................................................................................ 72 in.
Power Cord Gauge......................................................................................................................................... 12 AWG
Plug Included........................................................................................................................................................ Yes
Included Plug Type.............................................................................................................................................. 6-20
Switch Type............................................................................................................................. ON/OFF Push Button
Inverter (VFD) Type............................................................................................................................. Delta ME300
Inverter (VFD) Size............................................................................................................................................ 3 HP
Motors
Main
Horsepower............................................................................................................................................... 3 HP
Phase.................................................................................................................................................... 3-Phase
Amps.......................................................................................................................................................... 8.5A
Speed................................................................................................................................................ 1720 RPM
Type........................................................................................................................................ TEFC Induction
Power Transfer .......................................................................................................................................... Belt
Bearings.................................................................................................... Sealed & Permanently Lubricated
-6-
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
INTRODUCTION
Main Specifications
Operation Information
Swing Over Bed....................................................................................................................................... 18 in.
Swing Over Tool Rest Base............................................................................................................... 14-3/8 in.
Outboard Swing Over Bed....................................................................................................................... 26 in.
Distance Between Centers............................................................................................................. 26 & 40 in.
Swing Over Gap................................................................................................................................. 21-3/8 in.
Max. Distance Tool Rest to Spindle Center....................................................................................... 9-5/8 in.
No of Spindle Speeds.......................................................................................................................... Variable
Spindle Speed Range................................................................................................................ 50 - 3200 RPM
Floor to Center Height............................................................................................................................. 43 in.
Headstock Rotation.................................................................................................................................. Fixed
Spindle Information
Spindle Taper.......................................................................................................................................... MT#2
Spindle Thread Size................................................................................................................... 1-1/4" x 8 TPI
Spindle Thread Direction.............................................................................................................. Right Hand
Spindle Bore............................................................................................................................................ 5/8 in.
Type of Included Spindle Center.............................................................................................................. Spur
Indexed Spindle Increments................................................................................................................. 10 deg.
No of Indexes................................................................................................................................................. 36
Outboard Spindle Thread Direction............................................................................................. Right Hand
Outboard Spindle Size......................................................................................................................... 1-1/4 in.
Outboard Spindle TPI..................................................................................................................................... 8
Tool Rest Information
Tool Rest Width....................................................................................................................................... 12 in.
Tool Rest Post Diameter............................................................................................................................ 1 in.
Tool Rest Post Length......................................................................................................................... 2-1/2 in.
Tool Rest Base Height......................................................................................................................... 5-3/4 in.
Tailstock Information
Tailstock Quill Travel................................................................................................................................ 4 in.
Tailstock Taper........................................................................................................................................ MT#2
Type of Included Tailstock Center............................................................................................................ Live
Construction
Bed....................................................................................................................... Precision-Ground Cast Iron
Frame........................................................................................................................................................ Steel
Stand......................................................................................................................................................... Steel
Base........................................................................................................................................................... Steel
Headstock.......................................................................................................................................... Cast Iron
Tailstock............................................................................................................................................. Cast Iron
Paint Type/Finish.................................................................................................................... Powder Coated
Other Related Information
Bed Width............................................................................................................................................ 6-7/8 in.
Faceplate Size............................................................................................................................................ 6 in.
Other
Country of Origin ........................................................................................................................................... Taiwan
Warranty ........................................................................................................................................................ 2 Years
Approximate Assembly & Setup Time ................................................................................................... 15 Minutes
Serial Number Location .............................................................................................................................. ID Label
ISO 9001 Factory ................................................................................................................................................. Yes
-7-
South Bend Tools
Model SB1126
Operating all machinery and machining equipment can be dangerous or relatively safe depending on how it is installed and maintained, and the operator's experience, common sense, risk awareness, working conditions, and use of personal protective equipment (safety glasses, respirators, etc.).
The owner of this machinery or equipment is ultimately responsible for its safe use. This responsibility includes proper installation in a safe environment, personnel training and usage authorization, regular inspection and maintenance, manual availability and comprehension, application of safety devices, integrity of cutting tools or accessories, and the usage of approved personal protective equipment by all operators and bystanders.
The manufacturer of this machinery or equipment will not be held liable for injury or property damage from negligence, improper training, machine modifi cations, or misuse. Failure to read, understand, and follow the manual and safety labels may result in serious personal injury, including amputation, broken bones, electrocution, or death.
The signals used in this manual to identify hazard levels are as follows:
Owner’s Manual: All machinery and machining
Trained/Supervised Operators Only: Untrained

SAFETY

For Machines Mfd. Since 10/23

Understanding Risks of Machinery

Death or catastrophic harm WILL occur.
Death or catastrophic harm COULD occur.
Moderate injury or fi re MAY occur.
Machine or property damage may occur.

Basic Machine Safety

equipment presents serious injury hazards to untrained users. To reduce the risk of injury, anyone who uses THIS item MUST read and understand this entire manual before starting.
Personal Protective Equipment:
servicing this item may expose the user to fl ying debris, dust, smoke, dangerous chemicals, or loud noises. These hazards can result in eye injury, blindness, long­term respiratory damage, poisoning, cancer, reproductive harm or hearing loss. Reduce your risks from these hazards by wearing approved eye protection, respirator, gloves, or hearing protection.
Operating or
users can seriously injure themselves or bystanders. Only allow trained and properly supervised personnel to operate this item. Make sure safe operation instructions are clearly understood. If electrically powered, use padlocks and master switches, and remove start switch keys to prevent unauthorized use or accidental starting.
Guards/Covers:
moving parts during operation may cause severe entanglement, impact, cutting, or crushing injuries. Reduce this risk by keeping any included guards/covers/doors installed, fully functional, and positioned for maximum protection.
Accidental contact with
-8-
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
Entanglement: Loose clothing, gloves, neckties,
Chuck Keys or Adjusting Tools: Tools used to
SAFETY
jewelry or long hair may get caught in moving parts, causing entanglement, amputation, crushing, or strangulation. Reduce this risk by removing/securing these items so they cannot contact moving parts.
Mental Alertness: Operating this item with
reduced mental alertness increases the risk of accidental injury. Do not let a temporary influence or distraction lead to a permanent disability! Never operate when under the influence of drugs/alcohol, when tired, or otherwise distracted.
Safe Environment:
powered equipment in a wet environment may result in electrocution; operating near highly fl ammable materials may result in a fi re or explosion. Only operate this item in a dry location that is free from fl ammable materials.
Electrical Connection: With electrically
powered equipment, improper connections to the power source may result in electrocution or fire. Always adhere to all electrical requirements and applicable codes when connecting to the power source. Have all work inspected by a qualified electrician to minimize risk.
Disconnect Power: Adjusting or servicing
electrically powered equipment while it is connected to the power source greatly increases the risk of injury from accidental startup. Always disconnect power BEFORE any service or adjustments, including changing blades or other tooling.
Operating electrically
adjust spindles, chucks, or any moving/ rotating parts will become dangerous projectiles if left in place when the machine is started. Reduce this risk by developing the habit of always removing these tools immediately after using them.
Work Area:
the risks of accidental injury. Only operate this item in a clean, non-glaring, and well­lighted work area.
Properly Functioning Equipment:
maintained, damaged, or malfunctioning equipment has higher risks of causing serious personal injury compared to those that are properly maintained. To reduce this risk, always maintain this item to the highest standards and promptly repair/service a damaged or malfunctioning component. Always follow the maintenance instructions included in this documentation.
Unattended Operation:
equipment that is left unattended while running cannot be controlled and is dangerous to bystanders. Always turn the power OFF before walking away.
Health Hazards: Certain cutting fluids and
lubricants, or dust/smoke created when cutting, may contain chemicals known to the State of California to cause cancer, respiratory problems, birth defects, or other reproductive harm. Minimize exposure to these chemicals by wearing approved personal protective equipment and operating in a well ventilated area.
Clutter and dark shadows increase
Poorly
Electrically powered
Secure Workpiece/Tooling:
cutting tools, or rotating spindles can become dangerous projectiles if not secured or if they hit another object during operation. Reduce the risk of this hazard by verifying that all fastening devices are properly secured and items attached to spindles have enough clearance to safely rotate.
Loose workpieces,
Diffi cult Operations:
operations with which you are unfamiliar increases the risk of injury. If you experience difficulties performing the intended operation, STOP! Seek an alternative method to accomplish the same task, ask a qualified expert how the operation should be performed, or contact our Technical Support for assistance.
Attempting difficult
-9-
South Bend Tools
Model SB1126
SAFETY
For Machines Mfd. Since 10/23

Additional Wood Lathe Safety

Serious injury or death can occur from getting entangled in, crushed between, or struck by rotating parts on a lathe! Rotating workpieces can come loose and strike operator or bystanders with deadly force if they are improperly secured, rotated too fast, or are not strong enough for the rotational forces required for turning. Improper tool setup or usage can cause tool kickback or grabbing, resulting in impact injury or entanglement. To reduce the risk of operator (or bystander) injury or death, anyone operating this machine MUST completely heed the hazards and warnings below.
Verify Workpiece Integrity. Verify each workpiece
is free of knots, splits, nails, or foreign material to ensure it can safely rotate on spindle without breaking apart or causing tool kickback.
Properly Prepare Workpiece. Before mounting,
cut off waste portions to balance workpiece for safe rotation and removal of large edges that can catch on tooling.
Secure Locks. Verify tool rest, headstock, and
tailstock are secure before turning lathe ON.
Secure Workpiece. Use proven setup techniques
and always verify workpiece (and centers/ tooling holding workpiece) are well-secured before starting lathe. Only use high-quality fasteners with non-tapered heads for faceplate attachment.
Adjust Tool Support. An improperly supported
tool may be grabbed or ejected. Adjust tool rest approximately
1
8" above workpiece center line to
and provide proper support for turning tool. Firmly hold turning tool with both hands against tool rest.
Remove Adjustment Tools. Remove all chuck
keys, wrenches, and adjustment tools before turning lathe ON. These items can become deadly projectiles when spindle is started.
Check Clearances. Before starting spindle,
verify workpiece has adequate clearance by hand-rotating it through its entire range of motion.
Test New Setups. Test each new setup by starting
spindle rotation at lowest speed and standing to side of lathe until workpiece reaches full speed and you can verify safe rotation.
1
4" away from workpiece
Wear Proper PPE. Always wear a face shield and
safety glasses when operating lathe. Do not wear gloves, necktie or loose clothing. Keep long hair away from rotating spindle.
Use Correct Speeds. Select correct spindle
speed for workpiece size, type, shape, and condition. Use low speeds when roughing or when turning large, long, or non-concentric workpieces. Allow spindle to reach full speed before turning.
Avoid Tool Kickback. This occurs when turning
tool is grabbed or ejected from workpiece with great force. Commonly caused by poor workpiece selection/preparation, improper tool usage, or improper machine setup or tool rest adjustment.
Safely Perform Roughing. Use correct tool.
Take light cuts, use low speeds, and firmly support tool with both hands.
Use Sharp Tools. Sharp tools cut with less
resistance than dull tools. Using dull tools increases the risk of tool kickback or grabbing.
Safely Stopping Rotation. Always allow rotating
workpiece to stop on its own. Never put hands or another object on workpiece to stop it.
Safely Measure Workpiece. Only measure
mounted workpiece after it has completely stopped. Trying to measure a spinning workpiece increases entanglement risk.
Sanding/Polishing. To reduce entanglement
risk, remove tool rest before sanding. Never completely wrap sandpaper around workpiece.
-10 -
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126

PREPARATION

Preparation Overview Required for Setup

The purpose of the preparation section is to help you prepare your machine for operation. The list below outlines the basic process. Specific steps for each of these points will be covered in detail later in this section.
The typical preparation process is as follows:
1. Unpack the machine and inventory the
contents of the box/crate.
Clean the machine and its components.
2.
3. Identify an acceptable location for the
machine and move it to that location.
Level the machine using the adjustable feet.
4.
Assemble the loose components and make
5.
any necessary adjustments or inspections to ensure the machine is ready for operation.
Connect the machine to the power source.
6.
7. Test run the machine to make sure it
functions properly and is ready for operation.
Incorrect use of this machine can result in death or serious injury. For your own safety, read and understand this entire document before using.
The items listed below are required to successfully set up and prepare this machine for operation.
For Lifting
A forklift or other power lifting device (rated for a minimum of 775 lbs.)
• Lifting straps or chains (rated for a minimum of 775 lbs.)
For Power Connection
A power source that meets the minimum circuit requirements for this machine. (Refer to the Power Supply Requirements section for details.)
A qualified electrician to ensure a safe and code-compliant connection to the power source.
For Assembly
Safety Glasses (for each person)
Additional Person
Precision Level
Combo Wrench 3⁄4"
Hex Wrench 4mm
Disposable Gloves (As Needed)
Disposable Rags (As Needed)
Cleaner/Degreaser (As Needed)
Wear safety glasses during the entire setup process!
-11-
South Bend Tools
Model SB1126
Before installing the machine, consider the availability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed.
To minimize the risk of electrocution, fire, or equipment damage, installation work and electrical wiring must be done by a or qualified service personnel in accordance with applicable electrical codes and safety standards.
The full-load current rating is the amperage a machine draws at 100% of the rated output power. On machines with multiple motors, this is the amperage drawn by the largest motor or sum of all motors and electrical devices that might operate at one time during normal operations.
The full-load current is not the maximum amount of amps that the machine will draw. If the machine is overloaded, it will draw additional amps beyond the full-load rating.
If the machine is overloaded for a sufficient length of time, damage, overheating, or fire may result—especially if connected to an undersized circuit. To reduce the risk of these hazards, avoid overloading the machine during operation and make sure it is connected to a power supply circuit that meets the requirements in the following section.
This machine is prewired to operate on a power supply circuit that has a verified ground and meets the following requirements:
Note: The circuit requirements in this manual are for machine will be running at a time. If this machine will be connected to a shared circuit where multiple machines will be running at the same time, consult a qualified electrician to ensure the circuit is properly sized.
A power supply circuit includes all electrical equipment between the main breaker box or fuse panel in your building and the incoming power connections inside the machine. This circuit must be safely sized to handle the full-load current that may be drawn from the machine for an extended period of time. (If this machine is connected to a circuit protected by fuses, use a time delay fuse marked D.)
Serious injury could occur if you connect
Power Supply
PREPARATION
For Machines Mfd. Since 10/23
Requirements
Availability
Electrocution or fire may occur if machine is not correctly grounded and attached to the power supply. Use a qualified electrician to ensure a safe power connection.
n electrician
the machine to power before completing the setup process. DO NOT connect to power until instructed later in this manual.
Circuit Requirements
Nominal Voltage ........... 208V/220V/230V/240V
............................................................. 60 Hz
Cycle Phase Circuit Rating Plug/Receptacle (included)
................................................ Single-Phase
......................................... 20 Amps
............... NEMA 6-20
Full-Load Current Rating
Full-Load Rating at 220V ...................... 18 Amps
-12 -
For your own safety and protection of property, consult an electrician if you are unsure about wiring practices or applicable electrical codes.
a dedicated circuit—where only one
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
This machine must be grounded! In the event of certain types of grounding provides a path of least resistance for electric current electric shock.
This machine is equipped with a power cord that has grounding plug The plug receptacle (outlet) grounded in accordance with all local codes and ordinances.
Improper connection of the equipment­grounding wire can result in a risk of electric shock. The wire with green insulation (with or without yellow stripes) is the equipment­grounding wire. If repair or replacement of the power cord or plug is necessary, do not connect the equipment-grounding wire to a live (current carrying) terminal.
Check with an electrician or qualifi ed service personnel if you do not understand these grounding requirements, or if you are in doubt about whether the tool is properly grounded.
If you ever notice that a cord or plug is damaged or worn, disconnect it from power, and immediately replace it with a new one.
We do not recommend using an extension cord with this machine. If you must use one, only use it if absolutely necessary and only on a temporary basis.
Extension cords cause voltage drop, which may damage electrical components and shorten motor life. Voltage drop increases as the extension cord size gets longer and the gauge size gets smaller (higher gauge numbers indicate smaller sizes).
Any extension cord used with this machine must contain a ground wire, match the required plug and receptacle listed in the for the applicable voltage, and meet the following requirements:
PREPARATION
Grounding Requirements
malfunctions or breakdowns,
in order to reduce the risk of
an equipment-grounding wire and a
(similar to the figure below).
must only be inserted into a matching
that is properly installed and
GROUNDED
6-20 RECEPTACLE
Current Carrying Prongs
6-20 PLUG
Grounding Prong
Figure 5. NEMA 6-20 plug and receptacle.
DO NOT modify the included plug or use an adapter if it will not fit your receptacle. Instead, have a qualified electrician install the proper receptacle on a power supply circuit that is grounded and meets the requirements for this machine.
Extension Cords
Circuit Requirements
Minimum Gauge Size .............................. 12 AWG
Maximum Length (Shorter is Better)
.......... 50 ft.
-13 -
South Bend Tools
Model SB1126
This item was carefully packaged to prevent damage during transport. If you discover any damage, please immediately call Customer Service at need to file a freight claim, so save the containers and all packing materials for possible inspection by the carrier or its agent.

Unpacking

(360) 734-1540 for advice. You may

Inventory

PREPARATION
For Machines Mfd. Since 10/23
AA
Wood Crate (Figure 6) Qty
A. Lathe Assembly .................................... 1
—Headstock (Mounted) .......................... 1
—Tool Rest Base w/Tool Rest (Mounted) ....1
—Tailstock (Mounted) ............................ 1
—Faceplate 6" (Mounted) ....................... 2
Cardboard Box (Figure 7
B. Bed Extension.......................................1
Spur Center MT#2 ................................. 1
C.
Live Center MT#2 .................................. 1
D.
Knockout Tool ......................................1
E.
Spindle Wrench 1
F.
Center Holder ....................................... 1
G.
Hex Wrenches 3, 4, 6, 8mm ................1 Ea.
H.
Secondary Control Panel ......................... 1
I.
Hardware (Not Shown)
J.
—Cap Screws M10-1.5 x 30 .....................4
—Lock Washers 10mm ...........................4
—Flat Washers 10mm ............................4
—Cap Screws M8-1.25 x 20 .....................2
—Lock Washers 8mm ............................. 2
—Button Hd Cap Screws M6-1 x 12 ........... 2
) Qty
3
4" .............................. 1
Figure 6. Wood crate inventory.
BB
CC
II
HH
GG
Figure 7. Cardboard box inventory.
DD
EE
FF
If you cannot find an item on this list, carefully check around/inside the machine and packaging materials. Often, these items get lost in packaging materials while unpacking or they are pre-installed at the factory.
-14-
USE THIS CHART TO MATCH UP
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
PREPARATION

Hardware Recognition Chart

HARDWARE DURING THE INVENTORY
AND ASSEMBLY PROCESS.
#
10
1
/4"
5
/16"
3
/8"
7
/16"
1
/2"
MEASURE BOLT DIAMETER BY PLACING INSIDE CIRCLE
Key
4mm
5mm
6mm
8mm
10mm
12mm
LINES ARE 1MM APART
16mm
Hex Wrench
Cap Screw
External Retaining Ring
Flat Washer
5mm 10mm 15mm 20mm 25mm 30mm 35mm 40mm
45mm
50mm 55mm
60mm
65mm
70mm 75mm
Phillips Head Screw
Carriage Bolt
Internal Retaining Ring
Lock Washer
1
/4"
3
/8"
1
/2"
5
/8"
Flange Bolt
E-Clip
INCH APART
16
/
1
LINES ARE
Lock Nut
Hex Nut
5
/16"
7
/16"
9
/16"
3
/4"
7
/8"
1
1
/4"
1
1
/2"
1
3
1 2
2 2
3
2 3
Flat Head Screw
/4"
1
/4"
1
/2"
/4"
D
I
A
R
M
E
T
/8"
E
R
5
Wing Nut
A
W
E
H
S
Flat Head Cap Screw
A
W
D
I
A
R
9
/16"
M
E
T
E
R
E
H
S
Button
R
D
Tap Screw
S
A
H
W
D
I
A
R
M
E
E
T
1
E
/2"
R
Hex Bolt
D
I
A
R
M
E
H
S
D
I
A
M
E
T
E
R
S
A
I
A
M
E
4mm
T
E
R
A
W
H
S
A
W
D
I
A
R
M
E
H
E
T
E
R
W
D
I
A
R
M
E
H
E
T
S
E
A
R
W
5mm
I
A
M
E
T
E
R
D
I
A
R
M
E
H
S
A
E
T E
W
R
6mm
E
7
H
S
A
/16"
R
3
E
W
H
S
A
W
/8"
R
5
E
D
I
A
D
/16"
D
R
1
/4"
R
E
H
S
A
W
#
I
10
A
D
M
I
A
E
T
E
R
E
T
E
R
M
E
T
E
R
M
E
T
E
R
I
A
M
E
T
E
R
Head Screw
Set Screw
E
H
S
12mm
A
W
R
E
H
S
10mm
A
W
D
R
E
H
S
8mm
A
W
WASHERS ARE MEASURE BY THE INSIDE DIAMETER
-15 -
South Bend Tools
Model SB1126
The unpainted surfaces are coated with a heavy-duty rust preventative that prevents corrosion during shipment and The benefi t of this rust preventative is that it works very well. The downside is that it time-consuming
Be patient and do a careful job when removing the rust preventative spend doing this will reward you with smooth sliding parts and a better appreciation for the proper care of
Although there are many ways to successfully remove the rust preventative, the process works well in most situations
Before cleaning, gather the following:
• Disposable
• Cleaner/degreaser
Safety glasses & disposable gloves
Note:
WD•40 can be used to remove rust preventative. Before using these products, though, test them on an inconspicuous area of a painted surface to make sure they will not damage it.
GAS
Order online at
Call 1-800-523-477
PREPARATION

Cleaning & Protecting

For Machines Mfd. Since 10/23
at the factory
to thoroughly remove.
degreasers work extremely well and they have non-toxic fumes)
Automotive degreasers, mineral spirits, or
the unpainted surfaces.
rags
(certain citrus-based
. The time you
following
storage.
can be
cleaning and
-
.
Avoid chlorine-based solvents, such as acetone or brake parts cleaner that may damage painted surfaces. Always follow the manufacturer’s instructions when using any type of cleaning product.
Basic steps for removing rust preventative:
1. Put on safety glasses and disposable gloves.
2. Coat all surfaces that have rust preventative
with a liberal amount of your cleaner or degreaser and let them soak for a few minutes.
3. Wipe off the surfaces. If your cleaner or
degreaser is effective, the rust preventative will wipe off easily.
Note: To clean off thick coats of rust
preventative on fl at surfaces, such as beds or tables, use a PLASTIC paint scraper to scrape off the majority of the coating before wiping it off with your rag. (Do not use a metal scraper or it may scratch the surface.)
4. Repeat Steps 2–3 as necessary until clean,
then coat all unpainted surfaces with a quality metal protectant or light oil to prevent rust.
-16-
Gasoline and petroleum products have low flash points and can explode or cause fire if used for cleaning. Avoid using these products to remove rust preventative.
Many cleaning solvents are toxic if inhaled. Minimize your risk by only using these products in a well ventilated area.
T23692—Orange Power Degreaser
A great product for removing the waxy shipping grease from the non-painted parts of the machine during clean up.
www.grizzly.com
OR
7
Figure 8. T23692 Orange Power Degreaser.
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
Weight Load
Additionally, consider the weight of the operator
Physical Environment
The physical environment where your machine is operated is important for safe operation and longevity of machine in a dry environment that is free from excessive moisture, hazardous chemicals, airborne abrasives, or extreme conditions. Extreme conditions for this type of machinery are generally those where the ambient temperature the relative humidity 20–95% (non-condensing); or the environment is subject to vibration, shocks, or bumps.
Electrical Installation
Place this machine near an existing power source. Make sure all power cords are protected from traffic, material handling, moisture, chemicals, or other hazards. Make sure to leave access to a means of disconnecting the power source or engaging a lockout/tagout device.
Lighting
Lighting around the machine must be adequate enough to perform operations safely. Shadows, glare, or strobe effects that may distract or impede the operator must be eliminated.
PREPARATION

Location

Physical Environment Electrical Installation Lighting Weight Load
Space Allocation
parts. For best results, operate this
is outside the range of 41°–104°F;
is outside the range of
Refer to the Machine Specifi cations for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be installed on the machine, and the heaviest workpiece that will be used.
or flammable
and any dynamic loading that may occur when operating the machine.
Space Allocation
Consider the largest size of workpiece that will be processed through this machine and provide enough space around the machine for adequate operator material handling or the installation of auxiliary equipment. With permanent installations, leave enough space around the machine to open or remove doors/covers as required by the maintenance and service described in this manual.
31"
Min. 30" for Maintenance
= Electrical Connection
Figure 9. Working clearances.
Children or untrained people may be seriously
Wall
Motor
Access Door
69½"
injured by this machine. Only install in an access restricted location.
Bed
Extension
-17-
South Bend Tools
Model SB1126
PREPARATION
For Machines Mfd. Since 10/23

Lifting & Moving

This machine and its parts are heavy! Serious personal injury may occur if safe moving methods are not used. To reduce the risk of a lifting or dropping injury, ask others for help and use power equipment.
The Model SB1126 requires the use of lifting equipment such as a forklift, engine hoist, or boom crane. DO NOT attempt to lift or move machine without necessary assistance from other people. Each piece of lifting equipment must be rated for at least 775 lbs. to support dynamic loads that may be applied while lifting. Review Power Supply Requirements on Page 12, then prepare a permanent location for the machine.
Bed ExtensionBed Extension
Alignment Pin (1 of 2)Alignment Pin (1 of 2)
Figure 10. Bed extension installed on bed.
Move tailstock and tool rest base to far
6.
end of bed extension (see instructions in
Adjusting Tailstock on Page 23, and Adjusting Tool Rest on Page 27), then lock
them in place (see Figure 11).
x x 44
Position lifting straps towards headstock side of machine for balance. Headstock side is heavier than opposite side and may tip machine over if not fully supported.
To lift and move machine:
1. Move crate to desired location.
Remove crate top and sides, any blocks
2.
around machine base, then unbolt machine from shipping pallet.
Remove any support straps, parts inside
3.
machine, plastic wrap, and tie straps securing machine components.
With help from an additional person,
4.
position bed extension on alignment pins on right-hand end of bed (see Figure 10).
Secure bed extension with (4) M10-1.5 x 30
5.
cap screws, 10mm lock washers, and 10mm flat washers (see Figure 10).
Route lifting straps under bed as shown in
7.
Figure 11.
Lifting Straps
Tool Rest
Tailstock
Bed
Extension
Figure 11. Location of lifting equipment and machine
components.
With help from another person, use lifting
8.
equipment to raise machine just enough to clear shipping pallet, then remove pallet.
Lower machine into place, then adjust (6)
9.
adjustable feet to level machine.
-18 -
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126

Assembly

The machine must be fully assembled before it can be operated. Before beginning the assembly process, see Required for Setup on Page 11 and gather all listed items. To ensure the assembly process goes smoothly, first clean any parts that are covered or coated in heavy-duty rust preventative (if applicable).
PREPARATION
Place tools and centers in tool holder as
3.
desired (see Figure 13).
Note: Centers can also be placed in the center
holder installed in Step 2.
To assemble machine:
1. Attach secondary control panel to tailstock
using (2) M8-1.25 x 20 cap screws and 8mm lock washers (see Figure 12).
Attach center holder to secondary control
2.
panel using (2) M6-1 x 12 button head cap screws (see Figure 12).
Figure 13. Tool holder with tools.
SecondarySecondary
ControlControl
PanelPanel
x x 22
Figure 12. Secondary control panel installed.
TailstockTailstock
x x 22
CenterCenter HolderHolder
Note: For installing bed extension on
outboard side of machine, see instructions in Outboard Turning on Page 33.
-19 -
South Bend Tools
Model SB1126
PREPARATION
For Machines Mfd. Since 10/23

Test Run

After all preparation steps have been completed, the machine and its safety features must be tested to ensure correct operation. If you discover a problem with the operation of the machine or its safety components, do not operate it further until you have resolved the problem.
Note: Refer to Troubleshooting on Page 43 for solutions to common problems that may occur. If you need additional help, contact our Tech Support at (360) 734-1540.
The test run consists of verifying the following:
• Motor powers up and runs correctly.
• STOP buttons work correctly.
• POWER switch disabling key works correctly.
Serious injury or death can result from using this machine BEFORE understanding its controls and related safety information. DO NOT operate, or allow others to operate, machine until the information is understood.
s
i
t
w
T
PUSH
STOP
C
l
o
c
k
w
i
s
e
t
e
s
e
R
o
T
STOP Buon
Figure 14. Resetting STOP button.
Move power switch to ON position, turn
5.
spindle direction switch to FOR, then press START button to start spindle rotation (see Figure 15).
SpindleSpindle
Speed DialSpeed Dial
SpindleSpindle
DirectionDirection
SwitchSwitch
STOPSTOP
ButtonButton
DO NOT start machine until all preceding setup instructions have been performed. Operating an improperly set up machine may result in malfunction or unexpected results that can lead to serious injury, death, or machine/property damage.
To test run machine:
1. Clear all setup tools away from machine.
Turn spindle speed dial all the way
2.
counterclockwise, disengage spindle indexing pin, and move POWER switch to OFF position.
Connect machine to power by inserting
3.
power cord plug into a matching receptacle.
Twist each STOP button clockwise until
4.
it springs out (see Figure 14). This resets buttons so spindle can start.
POWERPOWER
SwitchSwitch
Figure 15. Location of main controls.
Verify motor starts up and runs smoothly
6.
without any unusual problems or noises.
— When operating correctly, machine runs
smoothly with little or no vibration or rubbing noises.
— Investigate and correct strange or unusual
noises or vibrations before operating machine further. Always disconnect machine from power when investigating or correcting potential problems.
Turn spindle speed dial all the way
7.
counterclockwise, then press STOP button on main control panel.
STARTSTART ButtonButton
-20 -
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
PREPARATION
8. WITHOUT resetting STOP button, press
START button. Machine should not start.
— If machine does not start, STOP button
safety feature is working correctly.
— If machine does start (with STOP button
pushed in), immediately disconnect power to machine. The STOP button safety feature is not working correctly. This safety feature must work properly before proceeding with regular operations. Call Tech Support for help.
Twist main control panel STOP button
9.
clockwise until it springs out.
Turn spindle direction switch to REV,
10.
then press START button to start spindle rotation.
Verify spindle is operating correctly by
11.
slowly turning spindle speed dial clockwise.
WITHOUT resetting STOP button, press
13.
START button. Machine should not start.
— If machine does not start, STOP button
safety feature is working correctly.
— If machine does start (with STOP button
pushed in), immediately disconnect power to machine. The STOP button safety feature is not working correctly. This safety feature must work properly before proceeding with regular operations. Call Tech Support for help.
Twist STOP button on secondary control
14.
panel clockwise until it springs out.
Move POWER switch to OFF position.
15.
Remove key from POWER switch, as shown
16.
in Figure 17.
— When operating correctly, spindle runs
smoothly with little or no vibration or rubbing noises.
— Investigate and correct strange or unusual
noises or vibrations before operating machine further. Always disconnect machine from power when investigating or correcting potential problems.
Turn spindle speed dial all the way
12.
counterclockwise, then press STOP button on secondary control panel (see Figure 16).
START ButtonSTART Button
STOP ButtonSTOP Button
SecondarySecondary
ControlControl
PanelPanel
Figure 17. Removing key from POWER switch.
Move POWER switch to ON position and
17.
try to turn machine ON by pressing START button.
— If machine does not turn ON, switch
disabling feature is working correctly.
— If machine does turn ON, immediately
disconnect power to machine. Switch disabling feature is not working correctly. Call Tech Support for help.
Figure 16. Location of secondary controls.
Move POWER switch to OFF position and
18.
insert key.
-21-
South Bend Tools
Model SB1126
The purpose of this overview is to provide the novice machine operator with a basic understanding of how the machine is used during operation, so they can more easily understand the controls discussed later in this manual.
Note:
it is not intended to be an instructional guide for performing actual machine operations. To learn more about specifi c operations and machining techniques, seek training from people experienced with this type of machine, and do additional research outside of this manual by reading "how­to" books, trade magazines, or websites.

OPERATION

For Machines Mfd. Since 10/23

Operation Overview

Due to the generic nature of this overview,
To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning any operations.
To reduce risk of eye injury from flying chips or lung damage from breathing dust, always wear safety glasses, a face shield,
If you are not experienced with this type of machine, WE STRONGLY RECOMMEND that you seek additional training outside of this manual. Read books/magazines or get formal training before beginning any projects. Regardless of the content in this section, South Bend Tools will not be held liable for accidents caused by lack of training.
and a respirator when operating this machine.
To complete a typical operation, the operator does the following:
1. Examines workpiece to make sure it is
suitable for turning. No extreme bows, knots, or cracks should exist.
Prepares and trims up workpiece with a
2.
bandsaw or table saw to make it roughly concentric.
Installs workpiece between centers, or
3.
attaches it to faceplate or chuck.
Adjusts tool rest according to type of
4.
operation, and sets minimum clearance between workpiece and lip of tool rest to ¼"gap.
Rotates workpiece by hand to verify spindle
5.
and workpiece rotate freely throughout full range of motion.
Verifies pulley speed range is set for type of
6.
wood and size of workpiece installed.
Verifies spindle speed dial is turned all the
7.
way counterclockwise so spindle does not start in high speed.
Ties back long hair and clothing, and puts on
8.
safety glasses, face shield, and respirator.
Turns spindle direction switch to FOR
9.
or REV, starts spindle rotation, adjusts spindle speed, and carefully begins turning operation, keeping chisel against tool rest entire time it is cutting.
Stops spindle rotation and turns machine
10.
OFF when operation is complete.
-22-
For Machines Mfd. Since 10/23 Model SB1126
OPERATION

Stock Inspection & Requirements

Some workpieces are not safe to turn or may require modification before they are safe to turn. Before turning, inspect all workpieces for the following:
Workpiece Type:
This machine is intended for turning natural
wood products. Never attempt to turn any composite wood materials, plastics, metal, stone, or rubber workpieces; turning these materials can lead to machine damage or severe injury.
Foreign Objects:
Nails, staples, dirt, rocks and other foreign
objects are often embedded in wood. While cutting, these objects can become dislodged and hit the operator, cause tool grab, or break the turning tool, which might then fly apart. Always visually inspect your workpiece for these items. If they can't be removed, DO NOT turn the workpiece.

Adjusting Tailstock

The Model SB1126 tailstock is equipped with a cam-action clamping system to secure it to the lathe bed. When the lever is tightened, a clamping plate lifts up underneath the bed and secures the tailstock in place. The tailstock can be positioned anywhere along the lathe bed.
If clamping plate is not tight enough for lock lever to fully secure tailstock base, it could unexpectedly slip during operation and workpiece could be ejected at high speed. Failure to heed this warning could result in serious personal injury.
To adjust tailstock:
1. Loosen tailstock lock lever and move
tailstock to desired position along bed, as shown in Figure 18.
Large/Loose Knots:
Loose knots can become dislodged during the
turning operation. Large knots can cause a workpiece to completely break in half during turning and cause machine damage and injury. Choose workpieces that do not have large/loose knots.
Excessive Warping:
Workpieces with excessive bowing or
twisting are unstable and unbalanced. Never turn these workpieces at high speed, or instability will be magnified and the workpiece can be ejected from the lathe causing injury. Only turn concentric workpieces!
Wet or "Green" Stock:
Turning wood with a moisture content over
20% can cause increased wear on tooling.
TailstockTailstock
LockLock
Lever
Figure 18. Tailstock lock lever location.
2. Tighten tailstock lock lever to secure
tailstock to bed.
Note: Large clamping plate and hex nut
underneath tailstock will require occasional adjusting to ensure proper clamping pressure of tailstock to bed. Turn this hex nut in small increments to fine-tune clamping pressure.
-23-
South Bend Tools
Model SB1126
OPERATION

Installing/Removing Tailstock Center

The included live center installs into the tailstock quill with an MT#2 tapered fit (see Figure 19).
For Machines Mfd. Since 10/23
QuillQuill
KeywayKeyway
TailstockTailstock
QuillQuill
LiveLive
CenterCenter
Figure 19. Location of tailstock components.
Items Needed Qty
Heavy Leather Gloves ............................. 1 Pr.
Clean Shop Rags Disposable Gloves Acetone/Lacquer Thinner
............................ As Needed
........................... As Needed
HandwheelHandwheel
QuillQuill LockLock
HandleHandle
................ As Needed
Installing Tailstock Center
1. Loosen quill lock handle and rotate
handwheel until quill extends about 1".
QuillQuill
SetSet
ScrewScrew
Figure 20. Quill set screw aligned with quill keyway.
Make sure center is securely installed by
5.
attempting to pull it out by hand—a properly installed center will not pull out easily.
Secure quill in place by tightening quill lock
6.
handle.
Removing Tailstock Center
1. Loosen quill lock handle.
Hold a clean rag under spindle or wear a
2.
glove to catch center when you remove it.
Rotate tailstock handwheel
3.
counterclockwise—tailstock quill will retract back into quill, causing center to be forced out.
Make sure mating surfaces of center and
2.
quill are free of debris and oily substances before inserting center to ensure a good fit and reduce runout.
Firmly insert tapered end of center into
3.
tailstock quill (see Figure 20).
Make sure quill set screw is aligned with
4.
quill keyway to ensure tailstock center and quill will not freely rotate under load (see Figure 20).
-24-
Tailstock quill must always be locked in place during lathe operation. Before tightening quill lock handle, quill keyway must be properly aligned. Otherwise, workpiece can be ejected from lathe at high speed causing serious personal injury or death.
!
!
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
Installing/Removing
OPERATION
Make sure center is securely installed by
4.
attempting to pull it out by hand—a properly installed center will not pull out easily.
Headstock Center
The included spur center installs into the headstock spindle with an MT#2 tapered fit.
Note: The process of installing/removing the headstock center is the same for both the outboard and inboard ends of the headstock.
Items Needed Qty
Knockout Tool ............................................1
Heavy Leather Gloves Clean Shop Rags Acetone/Lacquer Thinner
............................. 1 Pr.
............................ As Needed
................ As Needed
Installing Headstock Center
1. DISCONNECT MACHINE FROM POWER!
Make sure mating surfaces of center and
2.
spindle are free of debris and oily substances before inserting center to ensure a good fit and reduce runout.
Firmly insert tapered end of center into
3.
spindle, then push it in with a quick, firm motion (see Figure 21).
Removing Headstock Center
1. DISCONNECT MACHINE FROM POWER!
Hold a clean rag under spindle or wear heavy
2.
leather gloves to catch center when removed.
Insert knockout tool through opposite end
3.
of spindle and firmly tap back of center, catching it as it falls (see Figure 22).
Knockout ToolKnockout Tool
Figure 22. Example of removing headstock center
with knockout tool.
HeadstockHeadstock
Spur CenterSpur Center
Figure 21. Center installed in headstock spindle.
-25-
!
South Bend Tools
Model SB1126
OPERATION
Removing/Installing
For Machines Mfd. Since 10/23
Faceplate
These instructions cover removing and installing the faceplate. To mount a workpiece to your faceplate, see Faceplate Turning on Page 32.
Tools Needed Qty
Hex Wrench 3mm ........................................ 1
Spindle Wrench 1
Removing Faceplate
1. DISCONNECT MACHINE FROM POWER!
2. Engage spindle indexing pin on headstock
(see Figure 23).
Loosen (2) set screws on faceplate, as shown
3.
in Figure 23.
3
4" .................................... 1
Spindle Indexing PinSpindle Indexing Pin
To prevent faceplate and workpiece separating from spindle during operation, headstock faceplate MUST be firmly threaded onto spindle and secured in place by fully tightening (2) faceplate set screws. If these instructions are not properly performed, serious personal injury could occur.
Do not start lathe with indexing pin inserted into spindle; otherwise machine damage, property damage, or serious personal injury could occur.
Installing Faceplate
1. DISCONNECT MACHINE FROM POWER!
2. Engage spindle indexing pin on headstock
(see Figure 23).
x x 22
x x 22
Figure 23. Faceplates installed on spindle shaft.
Rotate faceplate counterclockwise until it is
4.
removed.
Note: If spur center is installed, it will be
remain in place during this process.
Disengage spindle indexing pin before
5.
resuming operations.
Loosen (2) set screws on faceplate, then
3.
thread faceplate clockwise onto spindle shaft until faceplate is secure against shoulder on spindle shaft (see Figure 23).
Tighten (2) set screws on faceplate to secure.
4.
Disengage spindle indexing pin before
5.
resuming operations.
-26-
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
OPERATION

Adjusting Tool Rest

The tool rest assembly consists of two components: the tool rest base (or banjo) and the tool rest. The tool rest base moves forward/ backward and along the length of the lathe bed. The tool rest rotates and moves up and down in the tool rest base. Locks for both components allow you to secure the tool rest in position after making these adjustments.
When adjusting the tool rest, position it as close as possible to the workpiece without actually touching it. This maximizes support where the cutting occurs and minimizes leverage, reducing the risk of injury if a "catch" occurs. Many woodturners typically set the height of the tool
1
⁄8" above or below the centerline of the
rest workpiece, depending on their height, the type of tool they are using, and the type of operation they are performing.
As a rule of thumb: For most (spindle) turning operations, the cutting tool should contact the workpiece slightly above centerline. For most inside (bowl) turning operations, the cutting tool should contact the workpiece slightly below centerline.
Keeping all these factors in mind, your main goal when adjusting the tool rest should be providing maximum support for the type of tool being used, in a position that is safe and comfortable for you.
To adjust tool rest:
1. Loosen tool rest base lock lever and move
tool rest assembly to desired position on lathe bed, as shown in Figure 24.
Note: To maximize support, tool rest base
should always be locked on both sides of bed. Never pull tool rest so far back that it is only secured on one side.
Tool RestTool Rest
Tool RestTool Rest
Figure 24. Tool rest assembly components.
If clamping plate is not tight enough for lock lever to fully secure tool rest base, or lock handle is not tight enough to fully secure tool rest, they could unexpectedly slip during operation and draw turning tool and your hand into spinning workpiece. Failure to heed this warning could result in serious personal injury.
Lock HandleLock Handle
Tool Rest BaseTool Rest Base
Lock LeverLock Lever
Improperly supported or positioned cutting tools can "catch" on workpiece, ejecting tool from your hands with great force. To reduce this risk, always ensure tool rest is properly positioned for each type of operation, cutting tool is firmly supported against tool rest BEFORE cutting, and cutting tool is properly positioned to cut at the correct angle for tool and operation type.
2. Rotate tool rest base lock lever until it feels
tight to secure tool rest base on bed.
Note: Large clamping plate and hex nut
underneath tool rest base will require occasional adjusting to ensure proper clamping pressure of tool rest assembly to bed. Turn this hex nut in small increments to fine tune clamping pressure as needed.
3. Loosen tool rest lock handle (see Figure 24).
4. Position tool rest in desired location.
5. Tighten tool rest lock handle to secure tool
rest in position.
-27-
!
South Bend Tools
Model SB1126
Changing Speed
OPERATION
For Machines Mfd. Since 10/23
Range
The Model SB1126 has two speed ranges for varied turning operations. These ranges are selected by changing belt positions on the motor and spindle pulleys (see Figure 25).
Spindle
= High Range
2
170–3200 RPM
= Low Range
1
50–900 RPM
Motor
Figure 25. Speed range belt positions.
2
1
Always choose correct spindle speed for an operation. Using wrong speed may lead to workpiece being thrown at high speed, causing severe or fatal impact injuries.
To change speed range:
1. DISCONNECT MACHINE FROM POWER!
2. Open belt access and motor access doors on
rear of machine (see Figure 26).
Belt AccessBelt Access
DoorDoor
High range (2) is best when turning a workpiece where a clean finish is required and only light cuts are made. Low range (1), which has more torque, is best when turning a workpiece where a lot of material must be removed and a rough finish does not matter. Use low range for spindle speeds of 900 RPM or less. Use the speed dial to adjust spindle speed within each range.
Refer to the chart below to choose the appropriate RPM for your operation. Choose the speed range that will include the selected RPM.
Workpiece
Diameter
Under 2" 1520 3200 3200
2–4" 760 1600 2480
4–6" 510 1080 1650
6–8" 380 810 1240
8–10" 300 650 1000
10–12" 255 540 830
12–14" 220 460 710
14–16" 190 400 620
Roughing
RPM
Cutting
RPM
Finishing
RPM
MotorMotor
Access DoorAccess Door
Figure 26. Belt and motor access locations.
3. Loosen belt-tension lock handle on motor
mount (see Figure 27).
Belt-TensionBelt-Tension Lock HandleLock Handle
Figure 27. Belt-tension lock handle location.
-28 -
!
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
OPERATION
4. Lift motor assembly all the way up, then
tighten belt-tension lock handle to hold motor in place.
5. Roll belt onto desired set of pulleys, as
shown in Figure 25 on Page 28.
6. Loosen belt-tension lock handle and lower
motor.
7. Apply downward pressure on motor assembly
to properly tension drive belt, then tighten belt-tension lock handle.
Note: When properly tensioned, belt should
deflect about applied to belt mid-way between upper and lower pulley, as shown in Figure 28.
1
/
8
" Deection
1
⁄8" when moderate pressure is
Spindle
Pulley

Indexing

Do not start lathe with indexing pin inserted into spindle; otherwise machine damage, property damage, or serious personal injury could occur.
Indexing on a lathe is typically used for workpiece layout and other auxiliary operations that require equal distances around the workpiece circumference, such as clock faces or inlays.
By inserting the spindle indexing pin into one of the 36 indices of the spindle, the workpiece can be positioned in 10° increments, as shown in the figures below.
Motor
Pulley
Figure 28. Testing belt deflection.
8. Close belt access and motor access doors on
rear of machine.
SpindleSpindle
Indexing PinIndexing Pin
IndexIndex
(1 of 36)(1 of 36)
Figure 29. Spindle indexing pin and indices.
Spindle
Spindle
Indexing
Pin
Headstock
Figure 30. Indexing configuration.
V-Belt
Index
(1 of 36)
-29-
South Bend Tools
Model SB1126
OPERATION
For Machines Mfd. Since 10/23

Spindle Turning

To reduce risk of eye injury from flying chips or lung damage from breathing dust, always wear safety glasses, a face shield, and a respirator when operating this machine.
Spindle turning is the operation performed when a workpiece is mounted between centers in the headstock and tailstock, as shown in Figure 31. Bowls, table legs, tool handles, and candlesticks are typical projects where this operation is used.
Spindle Turning
1. Find center point of both ends of workpiece
by drawing diagonal lines from corner to corner across ends (see Figure 32).
Workpiece
Pencil Lines
Marked Diagonally
Across Corners
Workpiece Center
Figure 32. Workpiece marked diagonally from corner
to corner to determine center.
Make a center mark by using a wood mallet
2.
and tapping point of spur center into center of workpiece on both ends.
Figure 31. Typical spindle turning operation.
Tools Needed Qty
Precision Ruler ...........................................1
Wood Mallet Power Drill Drill Bit Tablesaw/Bandsaw
............................................... 1
................................................ 1
1
4" ................................................ 1
...................................... 1
Using a
3.
1
4" drill bit, drill a
1
4" deep hole
at center mark on end of workpiece to be mounted on headstock spur center.
To help embed spur center into workpiece,
4.
1
cut
4" deep saw kerfs in headstock end of
workpiece along diagonal lines marked in Step 1.
If your workpiece is over 2" x 2", cut corners
5.
off workpiece lengthwise to make turning safer and easier (see Figure 33).
Workpiece
Cut O
Corners
-30-
Workpiece Center
Figure 33. Corners of workpiece removed.
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
OPERATION
6. Drive spur center into headstock-end center
mark of workpiece with a wood mallet to
1
embed it at least
4" into workpiece (see
Figure 34).
¼"
Figure 34. Spur center properly embedded.
With workpiece still attached, insert spur
7.
center into headstock spindle (see Installing/ Removing Headstock Center on Page 25
for additional instructions).
Note: Use tool rest to support opposite end of
workpiece so that workpiece and spur center do not separate during installation.
Install live center into tailstock quill and
8.
tighten quill lock handle to lock quill in position (see Page 24 for additional instructions).
Slide tailstock toward workpiece until point
9.
of live center touches workpiece center mark, then lock tailstock in this position.
Loosen quill lock handle and rotate tailstock
10.
handwheel to push live center into workpiece
1
at least
4".
Do not press workpiece too firmly with tailstock, or bearings will bind and overheat. Do not adjust tailstock too loosely, or workpiece will spin off lathe. Use good judgment and care, otherwise serious personal injury could result from workpiece being ejected at high speeds.
11.
Properly adjust tool rest to workpiece (see
Adjusting Tool Rest on Page 27).
Before beginning lathe operation, rotate
12.
workpiece by hand to ensure there is safe clearance on all sides.
Keep lathe tool resting on tool rest the ENTIRE time it is in contact with workpiece or when preparing to make contact between lathe tool and workpiece. Otherwise, spinning workpiece could force lathe tool out of your hands or entangle your hands with workpiece. Failure to heed this warning could result in serious personal injury.
Spindle Turning Tips
When turning the lathe ON, stand away
from the path of the spinning workpiece until the spindle reaches full speed and you can verify that the workpiece will not come loose.
Use the slowest speed when starting or
stopping the lathe.
Select the right speed for the size of the
workpiece that you are turning (refer to Changing Speed Range on Page 28).
Keep the turning tool on the tool rest the
ENTIRE time that it is in contact with the workpiece.
Learn the correct techniques for each tool
you will use. If you are unsure about how to use the lathe tools, read books or magazines about lathe techniques, and seek training from experienced and knowledgeable lathe users.
-31-
South Bend Tools
Model SB1126
OPERATION

Faceplate Turning

To reduce risk of eye injury from flying chips or lung damage from breathing dust, always wear safety glasses, a face shield, and a respirator when operating this machine.
Faceplate turning is when a workpiece is mounted to the faceplate, which is then mounted to the headstock spindle, as shown in Figure 35. This type of turning is usually done with open­faced workpieces like bowls or plates.
For Machines Mfd. Since 10/23
Center faceplate on workpiece and attach it
2.
(see Figure 36) with wood screws.
Figure 36. Typical attachment of faceplate to
workpiece.
Figure 35. Typical faceplate turning operation.
Mounting Workpiece on Faceplate
Items Needed Qty
Precision Ruler ...........................................1
Drill Bit Power Drill Tablesaw/Bandsaw Wood Screws
To mount workpiece on faceplate:
1. Mark workpiece center in same manner as
1
⁄4" ................................................ 1
................................................ 1
...................................... 1
................................. As Needed
described in Spindle Turning on Page 30.
Only use screws with non-tapered heads (see Figure 37) to attach faceplate to the workpiece. Screws with tapered heads can split faceplate or snap off during operation.
Non-Tapered Head Tapered Head
CORRECT
Figure 37. Correct and incorrect screw types.
Thread and secure faceplate onto headstock
3.
spindle.
— If wood screws cannot be placed in
workpiece, faceplate can be mounted to a backing block attached to workpiece (see
Mounting Workpiece on Backing Block on Page 33).
INCORRECT
Note: Cut off corners of workpiece to make it
as close to "round" as possible, as described in Step 5 of Spindle Turning on Page 30.
-32-
!
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
OPERATION
Mounting Workpiece on Backing Block
Items Needed Qty
Scrap Wood................................... As Needed
Precision Ruler Power Drill Drill Bit Clamp Wood Glue
1
....................................................... 1
To mount workpiece on backing block:
1. Make backing block from a suitable size piece
of scrap wood.
Note: Faces of backing block must be flat and
parallel with each other, or uneven surfaces will cause workpiece to spin eccentrically, causing unnecessary vibration and runout. It is best to mount backing block to faceplate and turn other surface flat prior to mounting.
Locate and mark center of workpiece and
2.
backing block.
Drill a 1⁄4" hole through center of backing
3.
block.
Look through hole in backing block to line up
4.
center with workpiece, then glue and clamp backing block to workpiece.
Note: Allow glue to cure according to
manufacturer's instructions.
Follow Steps 1–3 under Mounting Workpiece
5.
on Faceplate (see Page 32) to attach backing block to faceplate.
........................................... 1
................................................ 1
⁄4" ................................................ 1
.................................... As Needed

Outboard Turning

To reduce risk of eye injury from flying chips or lung damage from breathing dust, always wear safety glasses, a face shield, and a respirator when operating this machine.
Outboard turning is a variation of faceplate turning and is accomplished by removing the bed extension and installing it on the outboard end of the lathe, allowing for a larger turning capacity. Another method would be to use a floor-mounted tool rest, which would provide the maximum possible amount of swing.
Items Needed Qty
Additional Person .......................................1
Hex Wrench 8mm Bed Extension
Model SB1129 Outboard Tool Rest Base...........1
Tool Rest Cap Screws M10-1.5 x 30 Lock Washers 10mm Flat Washers 10mm
................................................... 1
To outboard turn:
1. DISCONNECT MACHINE FROM POWER!
2. With help from an additional person, remove
bed extension (if installed) and position on alignment pins on outboard end of machine (see Figure 38).
........................................ 1
............................................ 1
.............................. 4
.................................... 4
..................................... 4
AlignmentAlignment
PinPin
(1 of 2)(1 of 2)
Figure 38. Location of alignment pins.
-33-
South Bend Tools
Model SB1126
Secure bed extension with (4) M10-1.5 x 30
3.
cap screws, 10mm lock washers, and 10mm flat washers (see Figure 39).
Install Model SB1129 Outboard Tool Rest
4.
Base on bed extension (see Figure 39).
Note: To maximize support, tool rest base
should always be locked on both sides of bed. Never pull tool rest so far back that it is only secured on one side.
OPERATION
For Machines Mfd. Since 10/23

Sanding/Finishing

After the turning operations are complete, the workpiece can be sanded and finished before removing it from the lathe (see Figure 40).
Note: Whenever sanding or finishing, move tool rest holder out of the way to increase personal safety and gain adequate working room.
Tool RestTool Rest
Bed ExtensionBed Extension
Figure 39. Outboard bed extension installed with
optional SB1129 tool rest base.
5. Remove tool rest from SB1126 tool rest base
and install in outboard tool rest base.
When outboard turning, ALWAYS use a tool rest on bed extension or a floor-mounted tool rest, and keep tool in contact with rest during all turning operations. Failure to do so could cause tool to be pulled out of operator's control and ejected at high speed.
OutboardOutboard Tool RestTool Rest
BaseBase
x x 44
Figure 40. Typical sanding operation.
Sandpaper
Wrapping sandpaper completely around workpiece could pull your hands into moving workpiece and may cause serious injury. Never wrap sandpaper or finishing
Workpiece
materials completely around workpiece.
-34-
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
OPERATION

Selecting Turning Tools

Lathe tools come in a variety of shapes and sizes, and usually fall into five major categories:
Gouges
Mainly used for rough cutting, detail cutting, and cove profiles. The rough gouge is a hollow, double-ground tool with a round nose, and the detail gouge is a hollow, double-ground tool with either a round or pointed nose.
Scrapers
Typically used where access for other tools is limited, such as hollowing operations. This is a flat, double-ground tool that comes in a variety of profiles (round nose, spear point, square nose, etc.) to match many different contours.
Figure 43. Example of a round nose scraper.
Figure 41. Example of a gouge.
Skew Chisel
A versatile tool that can be used for planing, squaring, V-cutting, beading, and parting off. The skew chisel is flat, double-ground with one side higher than the other (usually at an angle of 20°–40°).
Parting Tools
Used for sizing and cutting off work. This is a flat tool with a sharp pointed nose that may be single- or double-ground.
Figure 44. Example of a parting tool.
Specialty Tools
These are unique, special function tools to aid in hollowing, bowl making, cutting profiles, etc.
Figure 42. Example of a skew chisel.
-35-
South Bend Tools
Model SB1126
order online at www.grizzly.com or call 1-800-523-4777

ACCESSORIES

For Machines Mfd. Since 10/23
Accessories
This section includes the most common accessories available for your machine, which are available through our exclusive dealer, Grizzly Industrial, Inc., at grizzly.com.
Installing unapproved accessories may cause machine to malfunction, resulting in serious personal injury or machine damage. To reduce this risk, only install accessories recommended by South Bend or Grizzly.
Refer to Grizzly's website or latest catalog for additional recommended accessories.
Recommended Metal Protectants
G5562—SLIPIT® 1 Qt. Gel G5563—SLIPIT® 11 Oz. Spray
T30024—Powered Respirator Kit
Breathing wood dust could cause severe respiratory illnesses. This kit is a lightweight, comfortable, and easy-to-carry device for protecting the airway from small particulates.
Figure 46. T30024 Powered Respirator Kit.
T32323—Woodturners Face Shield
Featuring a quick adjustment headpiece, this face shield is perfect for any woodturning project. Made of durable poly-carbonate, this shield provides security from flying chips and debris from the front and sides.
Figure 45. Recommended products for protecting
unpainted cast iron/steel part on machinery.
Figure 47. T32323 Woodturners Face Shield.
-36-
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
order online at www.grizzly.com or call 1-800-523-4777
ACCESSORIES
D3789—Lathe Chisel Set, 6-Pc.
Beautiful black walnut handles are contoured to fit your hands in any position, and high-speed steel (HSS) blades hold their edges for producing continuous ribbons of wood. Includes all of the standard lathe tools plus a 22¾" long ½" bowl gouge for all-day leverage and control. This set also comes with a sturdy aluminum case.
Figure 48. D3789 Lathe Chisel Set.
SB1129—Outboard Tool Rest Base
Designed specifically for the SB1126 18" x 40" Variable-Speed Wood Lathe, this tool rest base makes outboard turning easier and safer. Sized for tool rests with a 1" post diameter, the Model SB1129 includes an outboard tool rest base and lock lever, as well as a tool rest lock handle (tool rest not included). Provides a 15" outboard swing over tool rest base that allows the turner to keep the turning tool as close as possible to the shape of the workpiece for better tool control and increased safety.
T25611—The Missing Shop Manual: Lathe
The Missing Shop Manual explains the basics of safety and setup, and will help you get the most for your money by getting the most from your equipment. From sharpening your tools to faceplate, bowl, and spindle turning, you’ll discover the techniques and tips you need to maximize your lathe’s performance.
Figure 50. SB1129 Outboard Tool Rest Base.
Figure 49. T25611 The Missing Shop Manual: Lathe.
-37-
South Bend Tools
Model SB1126
!

MAINTENANC E

For Machines Mfd. Since 10/23

Maintenance Schedule

Always disconnect machine from power before performing maintenance or serious personal injury may result.
For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section.
To minimize your risk of injury and maintain proper machine operation, shut down the machine immediately if you ever observe any of the items below, and fix the problem before continuing operations:
Ongoing
Loose faceplate or mounting bolts.
Damaged center or tooling.
Worn or damaged wires.
Loose machine components.
Any other unsafe condition.

Cleaning

Cleaning the Model SB1126 is relatively easy. Vacuum excess wood chips and sawdust, and wipe off the remaining dust with a dry cloth. If any resin has built up, use a resin dissolving cleaner to remove it. Treat all unpainted cast iron and steel with a non-staining lubricant after cleaning.

Unpainted Cast Iron

Protect the unpainted cast iron surfaces on the bed by wiping the bed clean after every use— this ensures moisture from wood dust does not remain on bare metal surfaces. Keep beds rust­free with regular applications of products like SLIPIT
Bare metal surfaces can quickly develop surface rust if not coated. Machinery stored near windows in direct sunlight or where paints, thinners, or certain gasses are open to the air can experience bleaching, discoloring of paint or yellowing of clear plastic guards.
®
(Page 36).
Daily
Clean off dust buildup.
Clean and lubricate lathe bed, spindle, and
quill.
Monthly
Belt tension, damage, or wear.
Clean out dust buildup from machine
interior.

Lubrication

Since all bearings on the Model SB1126 are sealed and permanently lubricated, simply leave them alone until they need to be replaced. DO NOT lubricate them.
Wipe a lightly oiled shop rag on the outside of the headstock spindle. DO NOT allow any oil to get on the inside mating surfaces of the spindle.
Use the tailstock handwheel to extend the quill out to the furthest position and apply a thin coat of white lithium grease to the outside of the quill. DO NOT allow any oil or grease to get on the inside mating surfaces of the quill.
-38-
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126

Machine Storage

All machinery will develop serious rust problems and corrosion damage if it is not properly prepared for storage. If decommissioning this machine, use the steps in this section to ensure that it remains in good condition.
Items Needed Qty
Large Tarp or Plastic Sheet ........................... 1
Disposable Gloves Disposable Rags Desiccant Bags Cleaner/Degreaser Metal Protectant
........................... As Needed
............................. As Needed
.............................. As Needed
......................... As Needed
............................ As Needed
MAINTENANC E
Loosen or remove V-belt so it does not
3.
become stretched while the machine is not in use (see instructions in Replacing/ Tensioning V-Belt on Page 40).
Place generous quantities of desiccant
4.
bags inside cabinet, electrical boxes, and headstock.
Completely cover machine with a tarp or
5.
plastic sheet that will keep out dust and resist liquid or moisture. If machine will be stored in/near direct sunlight, use a cover that will block UV rays.
Removing Machine from Storage
Preparing Machine for Storage
1. Disconnect all power sources to machine.
2. Thoroughly clean all unpainted, bare metal
surfaces, then coat them with a lightweight grease or rust preventative. Take care to ensure these surfaces are completely covered but that grease or rust preventative is kept off of painted surfaces.
1. Remove cover from machine and any desiccant bags from interior.
Tension or install V-belt (see instructions in
2.
Replacing/Tensioning V-Belt on Page 40).
Follow all procedures for setup and testing as
3.
instructed in PREPARATION on Page 11.
Note: If machine will be out of service for
only a short period of time, use way oil or a good grade of medium-weight machine oil (not auto engine oil) in place of grease or rust preventative.
-39-
!
South Bend Tools
Model SB1126

SERVICE

Replacing/Tensioning V-Belt

The V-belt stretches as the lathe is used. Most of the stretching will occur during the first 16 hours, but may continue with further use. If the lathe loses power while making a cut, the V-belt may be slipping and need tensioning. If the V-belt shows signs of excessive wear or damage, replace it before further use.
For Machines Mfd. Since 10/23
Lift motor assembly all the way up, then
4.
tighten belt-tension lock handle to hold motor in place.
5. Roll V-belt off of pulleys and let hang out of the way for now.
6. Loosen (4) set screws securing outboard faceplate and spindle collar on spindle, then remove outboard faceplate and spindle collar (see Figure 52).
Items Needed Qty
Additional Person .......................................1
Replacement V-Belt (PSB1126009) Spindle Wrench 1 Hex Wrenches 3, 4mm Dead Blow Hammer Wood 2x4 (6" Length)
3
4" .................................... 1
.............................1 Ea.
..................................... 1
.................................. 1
................. 1
Replacing V-Belt
1. DISCONNECT MACHINE FROM POWER!
2. Open belt access and motor access doors on
rear of machine.
Loosen belt-tension lock handle on motor
3.
mount (see Figure 52).
Belt-TensionBelt-Tension Lock HandleLock Handle
Spindle CollarSpindle Collar
x x 22
x x 22
Figure 52. V-belt removal components.
7. Remove (2) cap screws and lock washers
securing spindle speed sensor, then move sensor out of the way (see Figure 53).
Spindle SpeedSpindle Speed
SensorSensor
Figure 51. Belt-tension lock handle location.
-40-
x x 22
Figure 53. Spindle speed sensor location.
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
SERVICE
8. With help from an additional person, push
spindle shaft through headstock towards bed (see Figure 54).
Note: Your assistant will need to support
spindle shaft and pulley until V-belt replacement is complete.
SpindleSpindle
PulleyPulley
BedBed
Figure 54. Spindle shaft components.
SpindleSpindle
ShaftShaft
HeadstockHeadstock
9. Pull V-belt off spindle pulley and remove
from machine.
10. Install replacement V-belt on spindle pulley
and verify grooves in V-belt are seated in grooves on spindle pulley.
13. Install spindle collar and outboard faceplate.
14. Roll V-belt over motor pulley and verify
grooves in V-belt are seated in grooves on motor pulley.
15. Perform Steps 45 of Tensioning V-Belt on this page.
Tensioning V-Belt
1. DISCONNECT MACHINE FROM POWER!
2. Open belt access and motor access doors on
rear of machine.
3. Loosen belt-tension lock handle and lower motor.
4. Apply downward pressure on motor assembly to properly tension drive belt, then tighten belt-tension lock handle.
Note: When properly tensioned, belt should
deflect about applied to belt mid-way between upper and lower pulley, as shown in Figure 55.
1
8" when moderate pressure is
Note: Spindle speed range is determined by
position of V-belt on pulleys (see Changing Speed Range on Page 28).
11. With help from an additional person, push
spindle shaft back through headstock towards outboard end of lathe, or use a dead blow hammer and wood block to gently tap spindle shaft.
Note: If spindle shaft bearings were unseated
during Step 8, re-seat bearings at this time.
12. Install spindle speed sensor and verify there
1
is a minimum clearance of
8" between tip of
sensor and spindle shaft.
Spindle
1
/
8
" Deection
Pulley
Motor
Pulley
Figure 55. Checking V-belt tension.
Close belt access and motor access doors on
5.
rear of machine.
-41-
!
South Bend Tools
Model SB1126
SERVICE
For Machines Mfd. Since 10/23

Aligning Pulleys

The motor and spindle pulleys are aligned at the factory and should not require any adjustment. If they become misaligned over time, it is important that they be re-aligned in order to extend belt life and maximize the transfer of power from the motor to the spindle.
The motor pulley can be adjusted by loosening the set screws, sliding the motor pulley in or out, then retightening the set screws to lock the motor pulley in place.
Tools Needed Qty
Straightedge 48" ........................................ 1
Hex Wrench 3mm
To align pulleys:
1. DISCONNECT MACHINE FROM POWER!
2. Open belt access and motor access doors on
rear of machine.
........................................ 1
— If pulleys are aligned, no adjustment is
needed. Proceed to Step 7.
— If pulleys are not aligned, go to Step 4.
Loosen (2) set screws on motor pulley shown
4.
in Figure 57.
x x 22
Belt-Tension Lock HandleBelt-Tension Lock Handle
Figure 57. Location of motor pulley alignment
components.
MotorMotor
PulleyPulley
Place a straightedge against both pulleys
3.
and check to make sure they are aligned (see Figure 56).
Spindle
Straightedge
Motor
Figure 56. Example of V-belt pulleys aligned.
Touching Evenly
Adjust motor pulley as needed until both
5.
pulleys are aligned.
Tighten and secure (2) set screws on motor
6.
pulley.
Close belt access and motor access doors on
7.
rear of machine.
-42-
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126

TROUBLESHOOTING

If you need replacement parts, or if you are unsure how to do any of the solutions given here, feel free to call us at (360) 734-1540.
Symptom Possible Cause Possible Solution
Machine does not start, or power supply breaker immediately trips after startup.
Machine stalls or is underpowered.
1.
Main power switch in OFF position.
2.
STOP button depressed/at fault.
3.
Switch disabling key removed.
4.
Incorrect power supply voltage or circuit size.
5.
Motor speed potentiometer at fault.
6.
Power supply circuit breaker tripped or fuse blown.
7.
Motor wires connected incorrectly.
8.
Wiring broken, disconnected, or corroded.
9.
START button or POWER switch at fault.
10.
Circuit board at fault.
11.
Spindle direction switch at fault.
12.
Inverter/VFD at fault.
13.
Motor or motor bearings at fault.
1.
Workpiece material unsuitable for machine.
2.
Feed rate/cutting speed too fast.
3.
Motor speed potentiometer at fault.
4.
Belt slipping/pulleys misaligned.
5.
Motor wires connected incorrectly.
6.
Pulley slipping on shaft.
7.
Machine undersized for task.
8.
Motor overheated.
9.
Extension cord too long.
10.
Motor speed potentiometer at fault.
11.
Spindle direction switch at fault.
12.
Motor or motor bearings at fault.
1.
Turn main power switch to ON position.
2.
Rotate STOP button head to reset. Replace if at fault.
3.
Install switch disabling key.
4.
Ensure correct power supply voltage and circuit size.
5.
Test/replace if at fault.
6.
Ensure circuit is free of shorts. Reset circuit breaker or replace fuse.
7.
Correct motor wiring connections (Page 47).
8.
Fix broken wires or disconnected/corroded connections.
9.
Inspect/replace if at fault.
10.
Inspect/replace if at fault.
11.
Test/replace switch.
12.
Inspect inverter/VFD; replace if at fault.
13.
Replace motor.
1.
Only cut wood and ensure moisture is below 20% (Page 23).
2.
Decrease feed rate/cutting speed.
3.
Test and replace if at fault.
4.
Clean/tension/replace belt (Page 40); ensure pulleys are aligned (Page 42).
5.
Correct motor wiring connections (Page 47).
6.
Tighten/replace loose pulley/shaft.
7.
Use sharp chisels; reduce feed rate or depth of cut.
8.
Clean motor, let cool, and reduce workload.
9.
Move machine closer to power supply; use shorter extension cord.
10.
Test and replace if at fault.
11.
Test/replace switch.
12.
Replace motor.
-43-
South Bend Tools
Model SB1126
TROUBLESHOOTING
For Machines Mfd. Since 10/23
Symptom Possible Cause Possible Solution
Machine has vibration or noisy operation.
Poor surface finish quality.
Excessive vibration upon startup (when workpiece is installed).
1.
Motor or component loose.
2.
Stand feet not adjusted properly.
3.
V-belt worn, loose, pulleys misaligned or belt slapping cover.
4.
Pulley loose.
5.
Motor mount loose/broken.
6.
Spindle loose, improperly installed or damaged.
7.
Spindle bearings at fault.
8.
Motor bearings at fault.
1.
Dull tooling or wrong tool used for task.
2.
Tool height is not correctly adjusted
1
to
8" above spindle centerline.
3.
Spindle speed incorrect.
4.
Excessive vibration.
1.
Workpiece mounted incorrectly.
2.
Workpiece warped, out of round, or flawed.
3.
Spindle speed too fast for workpiece.
4.
Workpiece hitting stationary object.
5.
Tailstock or tool rest not securely clamped to lathe bed.
6.
Belt pulleys are not properly aligned.
7.
Lathe is resting on an uneven surface.
8.
Motor mount bolts are loose.
9.
Belt is worn or damaged.
10.
Spindle bearings are worn or damaged.
1.
Replace damaged or missing bolts/nuts or tighten if loose.
2.
Adjust stand feet to stabilize machine.
3.
Inspect/replace belt. Realign pulleys if necessary (Page 42).
4.
Secure pulley on shaft (Page 42).
5.
Tighten/replace.
6.
Tighten loose spindle, re-install spindle ensuring mating surfaces are clean, replace damaged spindle.
7.
Test by rotating spindle; rotational grinding/loose shaft requires bearing replacement.
8.
Test by rotating shaft; rotational grinding/loose shaft requires bearing replacement.
1.
Sharpen tooling, select correct tool for operation.
1
2.
Adjust tool rest so tool is centerline (Page 27).
3.
Adjust for appropriate spindle speed (Page 28).
4.
Troubleshoot possible causes/solutions using table on Page 44.
1.
Remount workpiece; verify centers are embedded in centerline of workpiece (Pages 24–25).
2.
Cut workpiece to correct, or use a different workpiece.
3.
Reduce spindle speed (Page 28).
4.
Stop lathe and correct interference problem.
5.
Check lock levers and tighten if necessary (Pages 23 & 27).
6.
Align belt pulleys (Page 42).
7.
Shim stand or adjust feet to eliminate wobbles.
8.
Tighten motor mount bolts.
9.
Replace belt (Page 40).
10.
Test by rotating shaft; rotational grinding/loose shaft requires bearing replacement.
8" above spindle
-44-
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
TROUBLESHOOTING
Symptom Possible Cause Possible Solution
Turning tool grabs or digs into workpiece.
Tailstock moves under load.
Spindle lacks turning power or starts up slowly.
Quill does not move when handwheel is turned.
DRO does not display; reading incorrect.
1.
Wrong turning tool being used.
2.
Turning tool is too dull.
3.
Tool rest height not set correctly.
4.
Tool rest is set too far from workpiece.
1.
Tailstock mounting bolt/lock nut is loose.
2.
Bed or clamping surface is excessively oily or greasy.
1.
Belt is slipping.
2.
Pulleys loose.
3.
Workpiece too heavy for spindle.
1.
Keyway is not aligned with quill set screw.
1.
Wiring broken, disconnected, or corroded.
2.
Speed potentiometer at fault.
3.
Speed sensor at fault.
4.
Circuit board at fault.
1.
Use correct turning tool (Page 35).
2.
Sharpen or replace turning tool.
3.
Correct tool rest height (Page 27).
4.
Move tool rest closer to workpiece.
1.
Tighten mounting bolt/lock nut (Page 23).
2.
Clean bed or clamping surface to remove excess oil/ grease.
1.
Tighten/adjust belt (Page 40).
2.
Tighten pulley set screw; re-align/replace shaft, pulley set screw, and key (Page 42).
3.
Remove excess material before remounting; use lighter workpiece.
1.
Align quill keyway and quill set screw and slightly tighten screw to engage keyway (Page 24).
1.
Fix broken wires or disconnected/corroded connections.
2.
Test/replace if at fault.
3.
Verify spindle speed sensor has a minimum clearance of at fault.
4.
Inspect/replace if at fault.
1
8" from spindle shaft. Test/replace if
Motor braking resistor does not function; VFD displays "BR" error code.
1.
Wiring broken, disconnected, or corroded.
2.
Motor braking resistor at fault.
3.
Inverter/VFD at fault.
1.
Fix broken wires or disconnected/corroded connections.
2.
Test/replace if at fault.
3.
Inspect inverter/VFD; replace if at fault.
-45-
South Bend Tools
Model SB1126
Shock Hazard: It is extremely dangerous to
Wire Connections:
Modifi cations:
Motor Wiring:
junction box.
Circuit Requirements: Connecting the machine
power inverters store an electrical charge for
information included in this section, contact our Technical Support at (360) 734-1540.

ELECTRICAL

For Machines Mfd. Since 10/23

Electrical Safety Instructions

These pages are accurate at the time of printing. In the constant effort to improve, however, we may make changes to the electrical systems of future machines. Study this section carefully. If you see differences between your machine and what is shown in this section, call Technical Support at (360) 734-1540 for assistance BEFORE making any changes to the wiring on your machine.
perform electrical or wiring tasks while the machine is connected to the power source. Touching electrifi ed parts will result in personal injury including but not limited to severe burns, electrocution, or death. For your own safety, disconnect machine from the power source before servicing electrical components or performing any wiring tasks!
All connections must be tight to prevent wires from loosening during machine operation. Double-check all wires disconnected or connected during any wiring task to ensure tight connections.
Using aftermarket parts or modifying the wiring beyond what is shown in the diagram may lead to unpredictable results, including serious injury or fi re.
The motor wiring shown in these diagrams is current at the time of printing, but it may not match your machine. Always use the wiring diagram inside the motor
to an improperly sized circuit will greatly increase the risk of fi re. To minimize this risk, only connect the machine to a power circuit that meets the minimum requirements given in this manual.
Capacitors/Inverters: Some capacitors and
up to 10 minutes after being disconnected from the power source. To reduce the risk of being shocked, wait at least this long before working on capacitors.
Wire/Component Damage: Damaged wires
or components increase the risk of serious personal injury, fi re, or machine damage. If you notice that any wires or components are damaged while performing a wiring task, replace those wires or components before completing the task.
Experiencing Diffi culties: If you are
experiencing diffi culties understanding the
BLACK
BLUE
BROWN
NOTICE:
-46-
WIRING DIAGRAM COLOR KEY
BLUE WHITE
GREEN
G R AY
The photos and diagrams included in this section are best viewed in color. You can see them in color at www.southbendtools.com.
RED
LIGHT BLUE
ORANGE
PINK
PURPLE
TUR­QUIOSE
WHITE
YEL LOW GREEN
YEL LOW
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
MACHINE CABINET
HEADSTOCK
ELECTRICAL

Wiring Diagram

SPINDLE SPEED DRO
491247-000
P3
RC
P2
F2
L2
F2
L2
RA
RC
SPEED
CONTROL
RA
DIAL
300133-911
F1
L1
SECONDARY
F1
L1
SPEED SENSOR
491261-000
MAIN CONTROL PANEL
4
DIRECTION
SWITCH
KB2-BE102
GND
PEPE
E13
3
NO
4
NO
E14
STOP BUTTON
YIJIA LA36M 250V
PE
S13
E22
S14
E22
22
2
NC
1
NC
E21
START BUTTON
YK/YS-F2 250V
14
S14
21
13
S13
Ground
PE
X2 X1
X2
LED
KEYON
KE-22D S
110V/220 V
N L
POWER
SWITCH
JIHONG
J9 301A
X1
4
3
3
CONTROL PANEL
Ground
S13
21
4
NO
3
NO
22
START BUTTON
YK/YS-F2 250V
S14
14 13
E21
1
NC
E22
2
NC
STOP BUTTON
YIJIA LA36M 250V
PE
Ground
Hot
220 VAC
Hot
6-20 Plug
G
Ground
PE
FAN
STK
220V
T1
T2
T3
L1
L2
MOTOR 220V
R/L1 S/L2 T/ L3
POWER
U/T1 V/T2 W/T3
MOTOR
+2/B1 B2
3
2
1
MOTOR JUNCTION BOX
NPN
PNP
RA RB RC
RA
MI1
MI2
MI3
MI4
DCM
BR300W070
V
I
MI1
MI2 MI3 MI4 MI5 +24 +24 DCMDCM
VFD11AME21ANNAA
RC
+10V
+10
ACM
ACM AV I AFM MO1MOM PE
AVI
MOTOR BRAKING RESISTOR
VFD
D ELTA
-47-
South Bend Tools
Model SB1126
ELECTRICAL

Electrical Components

Figure 58. Main control panel wiring.
For Machines Mfd. Since 10/23
Figure 59. Motor junction box wiring.
Figure 60. VFD wiring.
Figure 61. Secondary control panel wiring.
-48-
Figure 62. Speed control wiring.
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
1
52
137
5
161

PARTS

Main

139
140
108
184
138
185
107
186
H
141
80
187
15
19
1
A
G
142
93
97
C
188
155
31
62
32
65
F
20
34
66
96
39
67
92
160
99
21
35
33
C
112
24 25 26
69
94
22
43
68
100
162
H
M
3
37
42
4
23
15
E
70
87
90
F
101
102
27
71
91
F
2-3
36
41
112
S
28
38
89
103
113
2-1
18
40
61
24 25 26
20
39
62
T
88
104
2-2
44
48
160
87
87
86
85 84
83
82
110
63
2
15
17
29
75
111
19
45
47
49
40
66
152
114
7
14
16
46
153
55
76
193
105
118
115
13
20
106
116
S
30
71
12
4
52
49
70
64
117
G
154
53
72
109
119
25
155
9
8
50
78
79
81
6
51
54
80
T
10
173
175
145
126
25
118
11
172
60
77-4
144
124
26
151
174
176
59
77-3
143
132
103
120
121
102 99
171
52
77-5
E
131
122
M
73
178
177
77-6
133-2
130
122
123
170
77-2
74
25
77-7
77-1
128
121
125
169
179
180
57
A
77-11
77-8
133-1
129
122
168
169
77-13
77-9
60
116
25 117
133-3
115
127
124
135 192 136
168V2
58
181
77-12
77-10
59
126 25 26
167
183
77
60
52
59
133
-49-
South Bend Tools
Model SB1126
REF PART # DE SCRIPT ION REF PART # DESCR IPT ION
PARTS
Main Parts List
1 PSB1126001 KN OB M6-1, D25, ROUN D 53 PSB1126053 ROLL PIN 5 X 25
2 PSB1126002 BELT ACCESS ASSEMBLY 54 PSB1126054 TAILSTOCK LOCK LEVER
2-1 PSB1126002-1 B ELT AC CES S DOOR 55 PSB1126055 Q UILL BUSHING
2-2 PSB1126002-2 HINGE PIN 57 PSB1126057 CAP SCREW M8-1.25 X 20
2-3 PSB1126002-3 DOOR B RACKET 58 PSB1126058 S TRAIN RELIEF TYPE-3 PG16
3 PSB1126003 CAP SCREW M6-1 X 8 59 PSB1126059 LOCK WASHER 6MM
4 PSB1126004 B UTTON HD CA P S CR M5-.8 X 10 60 PSB1126060 FLAT WASHER 6MM
5 PSB1126005 SPACER 35 X 45 X 20 61 PSB1126061 CABLE CLAMP ACC-3-B
6 PSB1126006 S ET SCREW M 5-.8 X 5 62 PSB1126062 FLAT WASHER 4MM
7 PSB1126007 SPIN DLE PULLEY 63 PSB1126063 PHLP HD SCR M4-.7 X 8
8 PSB1126008 SET S CREW M6-1 X 6 64 PSB1126064 S ENS OR C ORD 24G 3W 41"
9 PSB1126009 V-BELT 540J-8 65 PSB1126065 CAP SCREW M10-1.5 X 35
10 PSB1126010 COLLAR 35 X 45 X 10 66 PSB1126066 LOCK WASHER 10MM
11 PSB1126011 MAGNETIC S PA CER 35 X 45 X 1 5 67 PSB1126067 FLAT WASHER 10MM
12 PSB1126012 DETECTOR MOUNTING BRA CKET 68 PSB1126068 DOWEL P IN
13 PSB1126013 LOCK WASHER 5MM 69 PSB1126069 MAIN BED
14 PSB1126014 CAP SCREW M5-.8 X 10 70 PSB1126070 LOCK C OLLAR
15 PSB1126015 CABLE TIE ALT-085S -B 71 PSB1126071 LOCK N UT 3/4-10
16 PSB1126016 SPEED SENSOR 491261-000 72 PSB1126072 EXTENSION B ED
17 PSB1126017 PHLP HD SCR M3-.5 X 6 73 PSB1126073 B UTTON HD CAP SCR M6 -1 X 12
18 PSB1126018 DOOR MAGNET 1 /4" 74 PSB1126074 CEN TER HOLDER
19 PSB1126019 FACEPLATE 6" 75 PSB1126075 FLAT WASHER 10MM
20 PSB1126020 SET SCREW M6-1 X 1 0 76 PSB1126076 CAP SCREW M10-1.5 X 30
21 PSB1126021 LOCK COLLA R M35-1 .5 77 PSB1126077 IN VERTER/VFD AS SEMB LY
22 PSB1126022 BALL B EARING 6007-2NS E 77-1 PSB 1 1 260 77-1 BRA KING RES IS TOR BR300 W070
23 PSB1126023 HEADSTOCK 77-2 P SB112 6077-2 PHLP HD SCR M5-.8 X 8
24 PSB1126024 CAP SCREW M8-1.25 X 35 77-3 PS B 1 1 26 0 77-3 INVERTER/VFD MOUNT
25 PSB1126025 LOCK WASHER 8MM 77-4 PSB 1126077-4 PHLP HD SCR M5-.8 X 20, NYLON
26 PSB1126026 FLAT WASHER 8MM 77-5 PSB 1 1 260 77-5 FLAT WASHER 6.1 X 12.5 X 3.5MM
27 PSB1126027 B ALL BEA RIN G 60 08-2NSE 77-6 PSB 1126077-6 INVERTER/VFD DELTA VFD11AME21A N NAA
28 PSB1126028 S PIN DLE 77-7 PSB 1126077-7 HEX NUT M5-.8
29 PSB1126029 KEY 8 X 7 X 80 77-8 PSB112 6077-8 EXT TOOTH WA SHER 4MM
30 PSB1126030 SPUR CENTER 77-9 PS B 1 126 0 77-9 FLAT WASHER 4MM
31 PSB1126031 BUTTON HD CAP SCR M5-.8 X 12 77-1 0 PSB1126077-10 PHLP HD SCR M4-.7 X 8
32 PSB1126032 SPINDLE LOCK BRACKET 77-11 PSB1126077-11 VFD CORD 24G 2W 57"
33 PSB1126033 COMPRESSION SPRING 1.2 X 13 X 20MM 77-12 PSB1126077-12 VFD CORD 1 4G 4W 35"
34 PSB1126034 ROLL PIN 4 X 16 77-1 3 PSB1126077-13 POTENTIOMETER SONGUEI 16K4(F)
35 PSB1126035 SPINDLE LOCK SHAFT 78 PSB1126078 DOOR LA TCH
36 PSB1126036 TOOL REST 12" 79 PSB1126079 C ABIN ET DOOR
37 PSB1126037 TOOL REST BA SE 80 PSB1126080 BUTTON H D CAP SCR M6-1 X 1 0
38 PSB1126038 ADJUSTABLE HANDLE 3/8-16 X 1, 3L 81 PSB1126081 ELECTRICAL ACCESS COVER
39 PSB1126039 EXT RETA IN ING RING 22MM 82 PSB1126082 FENDER WASHER 6.5 X 23 X 4MM
40 PSB1126040 ROD E N D BOLT M16- 2 X 6 0 83 PSB1126083 MOTOR FOOT
41 PSB1126041 SET S CREW M5-.8 X 5 84 PSB1126084 FLAT WASHER 6MM
42 PSB1126042 TOOL REST B USHIN G 85 PSB1126085 BUTTON HD CAP SCR M6-1 X 25
43 PSB1126043 TOOL REST BASE LOCK LEVER 86 PSB1126086 CHIP B REAKER
44 PSB1126044 LIVE CENTER 87 PSB1126087 CAP SCREW M6-1 X 12
45 PSB1126045 Q UILL 88 PSB1126088 FOAM GASKET
46 PSB1126046 LEADSCREW 89 PSB1126089 ELECTRICAL FAN STK 220V
47 PSB1126047 TAILSTOCK 90 PSB1126090 FAN BRACKET
48 PSB1126048 ADJUSTABLE HANDLE M8-1.25 X 40, 75L 91 PSB1126091 PHLP HD SCR M5-.8 X 10
49 PSB1126049 EXT RETA IN ING RING 19MM 92 PSB1126092 ADJUSTA BLE KN OT-BALL Z IP TIE 6"
50 PSB1126050 HA NDWHEEL TYPE-35 127D X 18B, 3/8-16 93 PSB1126093 DUST SHIELD
51 PSB1126051 REVOLVIN G HA NDLE 90 X 2 4, 3/8-1 6 X 1 6 94 PSB1126094 LED KEYON KE-22DS 110V/220 V
52 PSB1126052 CAP SCREW M6-1 X 15 96 PSB1126096 EXT TOOTH WASHER 4MM
For Machines Mfd. Since 10/23
-50-
South Bend Tools
For Machines Mfd. Since 10/23 Model SB1126
REF PAR T # DE SCR IPT ION REF PART # DE SCR IPT ION
PARTS
Main Parts List (Cont.)
97 PSB1126097 PHLP HD SCR M4-.7 X 10 138 PSB1126138 SP EED CON TROL HOUSIN G
99 PSB1126099 ADJUSTABLE FOOT M12-1.75 X 50 139 PSB1126139 S PEE D CON TROL DI A L
100 PSB1126100 CABINET 140 PSB1126140 S ET S CREW M4-.7 X 8
101 PSB1126101 GROMMET 38MM, LOCKING 141 PSB1126141 DRO 491247-000
102 PSB1126102 B UTTON HD CAP SCR M8 -1.25 X 16 142 PSB1126142 TAP SCREW M3 X 8
103 PSB1126103 STRAIN RELIEF TYPE-1 5/8 143 PSB1126143 M OTOR P ULLEY
104 PSB1126104 CORD PLATE 144 PSB1126144 SET SCREW M6-1 X 6
105 PSB1126105 PHLP HD SCR M6-1 X 8 145 PSB1126145 S ET SCREW M6-1 X 8
106 PSB1126106 S TRAIN RELIEF TYPE-1 3/4 151 PSB1126151 O-RING 31.5 X 1.8
107 PSB1126107 CA BLE TIE ALT-1 50M-B 152 PSB1126152 CUSHION STRIP
108 PSB1126108 BUTTON HD CAP SC R M5-.8 X 8 153 PSB1126153 WELD N UT 5M M
109 PSB1126109 POWER CORD 12G 3W 118" 6-20P 154 PSB1126154 CAM NUT 8MM
110 PSB1126110 KN OCKOUT TOOL 155 PSB1126155 S ET S CREW M8-1 X 8
111 PSB1126111 SPINDLE WRENCH 1-3/4" 160 PSB1126160 ALIGNMENT PIN
112 PSB1126112 GROMMET 50MM, LOCKING 161 PSB1126161 EXT RETAIN IN G RIN G 35MM
113 PSB1126113 TOOL H OLDER 162 PSB1126162 WAVY WAS HER 35MM
114 PSB1126114 FLAT WASHER 8MM 164 PSB1126164 BUTTON H D CAP S CR M6-1 X 1 5
115 PSB1126115 CAP SCREW M8-1.25 X 20 167 PSB1126167 SWITCH BOX
116 PSB1126116 HEX NUT 5/16-18 168 PSB1126168 H EX N UT M4-. 7 V1
117 PSB1126117 F ENDER WAS HER 8MM 168V2 PSB1126168V2 LOCK NUT M4-.7 V2.02.24
118 PSB1126118 FOAM PAD 169 PSB1126169 FLAT WASHER 4MM
119 PSB1126119 CROSSBEAM 170 PSB1126170 EXT TOOTH WAS HER 4MM
120 PSB1126120 SIDE STAND 171 PSB1126171 SECONDARY CONTROL PANEL FACEPLATE
121 PSB1126121 CARRIAGE BOLT 5/16 -18 X 3/4 172 PSB1126172 BUTTON H D CAP S CR M4-.7 X 15
122 PSB1126122 FLAT WASHER 12MM 173 PSB1126173 STA RT B UTTON YK YS-F2 250V 22MM GRN
123 PSB1126123 LOCK NUT M12-1.75 174 PSB1126174 PHLP HD SCR M4-.7 X 10
124 PSB1126124 HEX BOLT M12-1.75 X 30 175 PSB1126175 S TOP B UTTON YIJ IA LA36M 2 50V 22M
125 PSB1126125 MOTOR L-BRACKET 176 PSB1126176 BUTTON H D CAP S CR M6-1 X 1 2
126 PSB1126126 CAP SCREW M8-1.25 X 20 1 77 PSB1126177 LOCK WASHER 6MM
127 PSB1126127 LOCK NUT M8-1.25 1 78 PSB1126178 FLAT WASHER 6MM
128 PSB1126128 MOTOR MOUNTING B RACKET 179 PSB1126179 SWITCH A RM
129 PSB1126129 MOTOR MOUN T H A N DLE 180 PSB1126180 CABLE CLAMP ACC-3-B
130 PSB1126130 FENDER WASH ER 10MM 181 PSB1126181 PHLP HD SCR M4-.7 X 8
131 PSB1126131 A DJUSTABLE HA NDLE M10 -1.5 X 25, 95L 183 PSB1126183 TAILSTOCK CORD 18G 4W 114"
132 PSB1126132 MOTOR SUPPORT B RACKET 184 PSB1126184 POWER SWITCH JIHONG J9301A 220V
133 PSB1126133 M OTOR A SSEMBLY 185 PSB1126185 DIRECTION SWITCH KB 2-B E102
133-1 PSB1126133-1 MOTOR 3H P 220V 3-PH 186 PSB1126186 S TOP B UTTON YIJIA LA36 M 250V 22M
133-2 PSB1126133-2 KEY 5 X 5 X 50 187 PSB1126187 START BUTTON YK YS-F2 250 V 22MM GRN
133-3 PSB1126133-3 STRAIN RELIEF TYPE-3 PG13.5 188 PSB1126188 CONTROL PANEL FACEPLATE
135 PSB1126135 HEX WRENCH 3MM 1 92 PSB1126192 HEX WRENCH 4MM
136 PSB1126136 HEX WRENCH 6MM 193 PSB1126193 CUSHION STRIP
137 PSB1126137 HEX WRENCH 8MM
-51-
South Bend Tools
Model SB1126
REF PART # DESCRIPTION REF PART # DESCRIPTION

Machine Labels

PARTS
For Machines Mfd. Since 10/23
216
215
201
206
211
201
214
212
202
203
206
205
207
204
213
208
209
210
201 PSB11 26201 KEEP DOOR CLOSED LABEL 209 PSB1126209 COMBO WAR NING LABEL
202 PSB1126202 SPINDLE LOCK NOTICE LABEL 210 PSB1126210 MODEL NUMBER LABEL
203 PSB1126203 MACHINE ID LABEL 211 PSB1126211 SOUTH BEND NAMEPLATE 203MM
204 PSB1126204 SPINDLE SPEED WARNING LABEL 212 PSB1126212 MAIN CONT ROL PANEL LABE L
205 PSB1126205 SECONDARY CONTROL PANEL LABEL 213 PSB1126213 SPEED CONTROL PANEL LABEL
206 PSB1126206 ELECTRICITY LABEL 21 4 PSB1126214 TOUCH-UP PAINT, SB DARK BLUE
207 PSB1126207 IMPACT WARNING LABEL 215 PSB1126215 T OU CH-UP PAINT, SB LIGHT BLU E
208 PSB1126208 QR CODE LABEL 216 PSB1126216 TO UCH-UP PAINT , SB GRAY
The safety labels provided with your machine are used to make the operator aware of the machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of these safety labels. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact South Bend Tools at (360) 734-1540 or www.southbendtools.com to order new labels.
-52-

Warranty

This quality product is warranted by South Bend Tools to the original buyer for 2 years from the date of purchase. This warranty does not apply to consumable parts, or defects due to any kind of misuse, abuse, negligence, accidents, repairs, alterations or lack of maintenance. We do not reimburse for third party repairs. In no event shall we be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our products.
We do not warrant or represent that this machine complies with the provisions of any law, act, code, regulation, or standard of any domestic or foreign government, industry, or authority. In no event shall South Bend’s liability under this warranty exceed the original purchase price paid for this machine. Any legal actions brought against South Bend Tools shall be tried in the State of Washington, County of Whatcom.
This is the sole written warranty for this machine. Any and all warranties that may be implied by law, including any merchantability or fitness, for any purpose, are hereby limited to the duration of this warranty.
Thank you for your business and continued support.
For further information about this warranty, visit
, or scan
the QR code below to be automatically directed to our warranty page.
https://www.grizzly.com/forms/warranty
WARRANT Y
southbendtools.com
southbendtools.com
Printed In U.S.A. #KS22867
Loading...