Southbend HDC-18-316L User Manual

Job Item#

www.yatesgd.com www.yatesgraphicdesign.com

Counterline - outdoor Charbroiler

Gas Radiant Countertop

Standard Features

- Available in 18”, 24”, and 36” widths

- 20,000 BTU (NAT or LP) stainless steel burner per 6”

- 316L stainless steel front, rear, sides, and bottom panels

- Reinforced, insulated double wall sides

- 316L Stainless steel radiants

- 3/4” rear gas connection and pressure regulator

- 5” high 316L stainless steel rear and side splash guards

- Two-position, two sided cooking grids

- 4” Spatula width grease trough

- Wide or narrow branding grates

- 316L stainless steel full width crumb tray

- One year limited Parts and Labor Warranty

Models:

HDC-18-316L, HDC-24-316L, HDC-36-316L

(Model HDC-36-316L)

STANDARD CONSTRUCTION SPECIFICATIONS

Exterior Finish: Front, rear, sides and bottom panels are con-

structed of 316L stainless steel. Sides are reinforced and fully
insulated. 5” rear and side splash.

Charbroiler: 18”, 24”, and 36” 316L Stainless steel, 20,000
BTU (NAT or LP) burners every 6”. Removable two-sided cast­iron grates.

Gas Heat Control System: Each straight burner is controlled

by a gas valve for independent control of ame. One standing

pilot services each burner. A 3/4” rear gas connection is
standard.

Legs: Stainless steel 4” adjustable legs.

Form HDC-316L Rev 0 (February/2017)

Printed in USA

1100 Old Honeycutt Road, Fuquay-Varina, NC 27526

[phone] www.southbendnc.com

Models:

33.25"
(845)

31.76"
(807)

16"

(406)

24

(61)

1.9"
(48)

2" (51)

21.5"
(546)

16"

(406)

31.3"
(795)

11"

(279)

5.3"

(135)

 HDC-18-316L  HDC-24-316L  HDC-36-316L

moDel WiDth

HDC-18-316L

HDC-24-316L

HDC-36-316L

Shipping Crate DimenSionS & Weight

18”

(457)

24”

(610)

36”

(915)

BurnerS

@20,000 Btu

CrateD

WiDth

15.5”

3

(394)

31”

4

(788)

55”

6

(1398)

CrateD

Depth

39”

(991)

39”

(991)

39”

(991)

CrateD
Weight

120 lbs
(54 kg)

240 lbs

(108 kg)

350 lbs

(159 kg)

UTILITY INFORMATION

GAS: Each unit has a 3/4” rear
gas connection with a male NPT
connector. Minimum supply pressure
is 7” W.C. for natural gas and 11”
W.C. for propane. All units require
a regulated gas supply. Pressure

regulator included. If using a exible

hose gas connection, the I.D. of
the hose must not be smaller than
the connector on the unit and
must comply with ANSI Z21.69,
providing an adequate means of
restraint to prevent undue strain on the gas connection.

 316L Stainless steel stand

 All Terrain 10” casters

 Plated grids for sh

moDel

HDC-18-316L 60,000 60,000

HDC-24-316L 80,000 80,000

HDC-36-316L 120,000 120,000

gaS (Btu/hr)

natural propane

- If casters are used with ex hose, a restraining device should be
used to eliminate undue stain on the ex hose.

- For use in non-combustible locations only.

- Minimum clearance from noncombustible construction is zero.

- Install under vented hood.

- Check local codes for re and sanitary regulations.

NOTICE:

Southbend has a policy of continuous product research and

improvement. We reserve the right to change specications and

product design without notice. Such revisions do not entitle the
buyer to corresponding changes, improvements, additions or
replacements for previously purchased equipment.

OPTIONS AND ACCESSORIES

 2” high insulator base for mounting on refrigerated base

 Battery Spark Ignition

MISCELLANEOUS

Form HDC-316L Rev 0 (February/2017)

INTENDED FOR COMMERCIAL USE ONLY.

NOT FOR HOUSEHOLD USE.