SoundTube RS1001I-II-T-SUB Specifications

RS1001i-II-T

Specifications:

System Type

Impedance (nominal)
Sensitivity dB @ 2.83 V/1 m
Sensitivity dB @ 1 W/1 m
Frequency Response (- 3 dB)
Frequency Response (-10 dB)
Max. Program Power
Max. Continuous Power RMS
Max. Power SPL @ 1 m 6
Tap Selector
Transducer - Low-Frequency Driver
Low-Frequency Voice Coil
Network Type: Low-Pass
Network Type: High-Pass
Enclosure Material
Grille
Inputs
Colors
Height
Diameter
Weight
Shipping Weight
Included accessories
Optional accessories
Packaging
Regulatory - UL
Regulatory - CE
RoHS

1

Impedance listed per IEC 60268-5

2

1 W 1 m sensitivity determined using nominal
impedance

3

Frequency response measured in half or full space
as dictated by speaker mounting configuration

4

Max program power is 3 dB above max
continuous power

5

Continuous power rating, EIA-426-B test

6

Max output based on max continuous power

7

Max useable SPL based on testing
by NWAA Labs

RS1001i-II-T

1

2

3

4

5

3

150 W 105.0 dB
75 W 102.0 dB
38 W 99.0 dB
19 W 96.0 dB

10-inch subwoofer, open-ceiling, ported (150-watt transformer for
25/70.7/100-volt or transformer bypass applications)
4 ohm

86.0 dB

83.0 dB
53 Hz - 175 Hz
38 Hz - 450 Hz
300 W
150 W

105.0 dB
Five-position rotary switch with transformer bypass
254 mm (10 in.) polypropylene cone, butyl rubber surround

35.0 mm / 1.38 in.
6 dB per octave, 1st order
N/A
Injection-molded ABS, glass fiber reinforced
Powder coated steel

Four-pin, 5.08 mm Euroblock for individual or daisy chain connection

Black or white

437.6 mm (17.23 in.)

376.4 mm (14.82 in.)

12.3 kg (27.0 lbs)

14.8 kg (32.5 lbs)
Hanging hardware, Euroblock connector, terminal weather boot
Surface-mount bracket (AC-RS-SM8)
One per box
1480 (UEAY) and 2239-approved
Approved
Approved

Transformer Taps

70.7 V Output 100 V Output 25 V Output

Open-Ceiling Subwoofer

Technical Information for System Engineers

150 W 105.0 dB
75 W 102.0 dB
38 W 99.0 dB

19 W 96.0 dB

9.5 W 93.0 dB

4.8 W 90.0 dB

2.4 W 87.0 dB

Key Features

• One 10 inch (254 mm) polypropylene cone
with a butyl rubber surround attached to a
reinforced baffle.

• Baffle-mounted, flared and tuned ports
for maximum efficiency and frequency
response.

• High-output (105 dB) and maximum effi­ciency with an accentuated 70 Hz peak to
maximize listener’s low-frequency experi­ence.

• 150-watt, low insertion-loss transformer
with an easy-access, five-position tap switch
for 25/70.7/100-volt and transformer bypass
positions.

• Weatherized components including pow­der-coated steel grille, hanging hardware
and a durable ABS enclosure for indoor/out­door applications.

• Includes UL listed hanging hardware with
high-quality cables and integrated Speed­Clamp™ self-locking wire clamp for fast,
easy and secure installation.

• UL 1480 (UEAY) and CE-approved. Hang­ing hardware is UL 2239-approved.

• High-quality black or white painted
finish. Custom colors available.

• Included accessories: hanging hardware,
Euroblock connector, terminal weather boot.

• Optional accessories: surface-mount
bracket (AC-RS-SM8).

Description

The RS1001i is a 10-inch open-ceiling or
surface-mount subwoofer tuned for maximum
output and performance across the operating
bandwidth. By incorporating a 10-inch poly­propylene woofer and a butyl rubber surround
in a tuned and ported enclosure, this speaker
delivers maximum low frequency response (38
Hz – 450 Hz, - 10 dB, independently verified)
and high SPL (105 dB).

Mounting hardware includes high-quality UL
listed cables and integrated SpeedClamp™
self-locking wire clamp for fast, easy and
secure installation. For easy ordering, stock­ing and installation, the RS1001i-II-T includes
a five-position tap switch for 25-, 70.7- and 100­volt applications with a transformer bypass
position.

© 2010 SoundTube Entertainment. All rights reserved. PN-TS-CMEZ REV 09.28.10

RS1001i-II-T

Open-Ceiling Subwoofer

Technical Information for System Engineers

Applications

The RS1001i-II-T is an indoor/outdoor,
background to foreground subwoofer for
installations where high quality, true bass
response and rapid installation are critical
variables. Aerobic rooms, retail, restau­rants, nightclubs, bars, theme parks, are­nas, ballrooms and churches are all ideal
fits for the RS1001i-II-T.

Because overall system design is a criti­cal component of subwoofer integration,
SoundTube engineering recommends
incorporating a DSP system with an active
crossover to maximize subwoofer integra­tion and overall system performance. Tun­ing the system based on room acoustics
and loudspeaker selection will result in
smooth response and reduced subwoofer
localization. For system engineering assis­tance, contact SoundTube at engineering@
soundtube.com or by calling 800-647-8823
(international: [phone]).

BroadBeam® Wide
Dispersion Technology

SoundTube’s proprietary BroadBeam®
technology incorporates a high-frequency
waveguide mated to a 1-inch convex alu­minum tweeter. The BroadBeam® high­frequency waveguide delivers a consistent
dispersion pattern across the upper reg­isters of the frequency spectrum (up to 10
kHz, independently verified). The result
is better edge-to-edge coverage, reduced
power needs, shorter installation time and
cost savings on shipping and labor.

Patented SoundTube
Technologies

SoundTube Entertainment and MSE
Audio Group constantly develop new
technologies that enhance audio product
performance. SoundTube Entertainment
innovations are protected by multiple
U.S. and international patents, which
explicitly cover SoundTube dispersion,
enclosure and dome technologies. MSE
Audio Group actively defends its patents
in order to protect SoundTube resellers
and end users.

Technical Data and
Specification Tools

Technical Data

SoundTube Entertainment strives to

provide complete and effective technical
information and data to dealers, engi­neers and designers. All data are avail­able from SoundTube Entertainment or at
www.soundtube.com.

Technical data and downloads include:

EASE™ data – 3-D polar plots.

EASE™ Address – 2-D modeling for dis­tributed systems

Autodesk® Revit® software

Tech Sheets – Technical information and
architectural specs for system engineers

SoundTubeSPEC™ – Proprietary speaker
placement software

Data Acquisition and Verification

All data for SoundTube speakers are
independently collected from and veri­fied by NWAA Labs (www.nwaalabs.
com) using their proprietary MACH test­ing system. All data are collected and
analyzed according to ASTM, ISO and
AES standards using EASRA, TEF and
MLSSA. Full balloon data including both
phase and magnitude are compiled into
a variety of formats including EASE 4.x,
GLL and CLF.

Architectural Specifications

The subwoofer shall consist of one 254
mm (10 in.) low-frequency transducer
installed in a ported enclosure. The trans­ducer shall have a polypropylene cone with
a butyl rubber surround.

Performance specifications of a typical
production unit shall be as follows: Usable
frequency range shall extend from 38 Hz

- 450 Hz (-10 dB, independently verified.)
Maximum continuous output at 1 meter
shall be at least 105 dB. The subwoofer shall
be usable at 25/70.7/100 volts with selectable
tap settings up to 150 watts or tranformer
bypass position. Rated power capacity of the
components and network shall be at least 150
watts continuous RMS and conform to EIA­426-B testing.

The enclosure shall be constructed of
injection-molded, glass-reinforced ABS. The
grille shall be constructed of powder-coated
steel.

Installation for the subwoofer shall be by
UL listed, galvanized steel cable affixed to
the speaker chassis via an integrated hook
assembly. For safety redundancy, a second-

ary hanging cable shall be included and
attach to the speaker chassis. The external
wiring input connector shall be a four-pin,

5.08 mm Euroblock for 4-ohm or distrib­uted systems and shall accept from 10 –
22-gauge wire.

The unit shall be factory preset to 150
watts in the 70.7-volt operating mode with a
tap switch located on the front baffle.

The enclosure shall be constructed of
injection-molded, glass-reinforced ABS.
The grille shall be constructed of powder­coated steel for lasting performance in the
elements. Overall cabinet dimensions shall
be no more than 437.6 mm (17.23 in.) in
height by 376.4 mm (14.82 in.) in diameter.

The subwoofer shall include hanging
hardware, Euroblock connector and
weather-resistant terminal boot.

The system shall be the SoundTube
RS1001i-II-T for low- and high-impedance
applications.

SoundTube Entertainment

6430 North Business Park Loop
Park City, Utah 84098
Phone [phone]
Fax [phone]
Toll Free 800.647.TUBE
www.soundtube.com