SoundTube CM62-EZ-II-BK Installation Guide
CM-EZ / BGM SeriesCM-EZ / BGM Series
Install Instructions For:
CM42-EZs-II, CM62-EZ-II, CM62-EZs-II, CM82-EZ-II, CM82-EZs-II, CM82-EZ-FS, CM82-EZs-FS, CM52-BGM, CM52s-BGM,
CM62-BGM and CM82-BGM
Ceiling thickness tolerances
Max
40.9 mm (1.60 in)
Min
0.9 mm (0.035 in)
CM-EZ / BGM SeriesCM-EZ / BGM Series
Droptile Ceiling Install Instructions For:
CM42-EZs-II, CM62-EZ-II, CM62-EZs-II, CM82-EZ-II, CM82-EZs-II, CM82-EZ-FS, CM82-EZs-FS, CM52-BGM, CM52s-BGM,
CM62-BGM and CM82-BGM
CM-EZ / BGM SeriesCM-EZ / BGM Series
Sheetrock Ceiling Install Instructions For:
CM42-EZs-II, CM62-EZ-II, CM62-EZs-II, CM82-EZ-II, CM82-EZs-II, CM82-EZ-FS, CM82-EZs-FS, CM52-BGM, CM52s-BGM,
CM62-BGM and CM82-BGM
CM-EZ / BGM SeriesCM-EZ / BGM Series
Pre-Construction Bracket Instructions For:
CM42-EZs-II, CM62-EZ-II, CM62-EZs-II, CM82-EZ-II, CM82-EZs-II, CM82-EZ-FS, CM82-EZs-FS, CM52-BGM, CM52s-BGM,
CM62-BGM and CM82-BGM
Tile bridge
Flexible conduit clamp
Cover plate
CM42-EZs Ceiling thickness tolerances
Max
38.1 mm (1.50 in)
Secondary attachment point
Speed Wing™ mounting arms
Bae
Min
.00 mm (.00 in)
1. Unpack speaker & set
aside grille assembly.
5. Tighten screw on terminal
plate, and push conduit
connector into knockout.
2. Use included tile bridge to
mark cutout in tile.
6. Insert speaker into
mounting hole with
installation aid in place.
Screw down both bolts on
the bae face to actuate the
mounting wings. Firmly
secure both bolts – do not
over-tighten.
3. Use Rotozip or other tool
to cut hole.
Hole Diameters
CM42-EZs-II
165.1 mm (6.50 in)
All other CMEZ and BGM models
266.7 mm (10.50 in)
7. If required, a sheet-metal
tab located on the rear
panel of the speaker serves
as a secondary point of
attachment (cable not
included).
4. Run signal wires through
conduit connector, then through
cover plate. Connect to ceramic
terminal strip. Two + and two connectors are provided for
daisy chaining.
8. Once all painting and
nish work is completed,
remove the paint mask.
1. Unpack speaker & set
aside grille assembly.
5. Tighten screw on terminal
plate, and push conduit
connector into knockout.
2. Use included tile bridge to
mark cutout in sheetrock.
6. If required, a sheet-metal
tab located on the rear
panel of the speaker serves
as a secondary point of
attachment (cable not
included).
3. Use Rotozip or other tool
to cut hole.
Hole Diameters
CM42-EZs-II
165.1 mm (6.50 in)
All other CMEZ and BGM models
266.7 mm (10.50 in)
7. Insert speaker into
mounting hole with
installation aid in place.
Screw down both bolts on
the bae face to actuate the
mounting wings. Firmly
secure both bolts – do not
over-tighten.
4. Run signal wires through
conduit connector, then through
cover plate. Connect to ceramic
terminal strip. Two + and two connectors are provided for
daisy chaining.
8. Once all painting and nish
work is completed, remove the
paint mask.
1. Nail or screw bracket to
joists. Secure conduit/signal
wire away from hole in
bracket.
5. Tighten screw on terminal
plate, and push conduit
connector into knockout.
2. Complete Finish work.
6. If required, a sheet-metal
tab located on the rear
panel of the speaker serves
as a secondary point of
attachment (cable not
included).
3. Use Rotozip or other tool
to cut hole.
Hole Diameters
CM42-EZs-II
165.1 mm (6.50 in)
All other CMEZ and BGM models
266.7 mm (10.50 in)
7. Insert speaker into
mounting hole with
installation aid in place.
Screw down both bolts on
the bae face to actuate the
mounting wings. Firmly
secure both bolts – do not
over-tighten.
4. Run signal wires through
conduit connector, then through
cover plate. Connect to ceramic
terminal strip. Two + and two connectors are provided for
daisy chaining.
7. Once all painting and
nish work is completed,
remove the paint mask.
Box contents
1 Speaker
1 Flexible conduit clamp
1 Cover plate
1 Grille
1 Installation aid/paint mask
(CM82-EZ-FS and CM82-EZs-FS are UL1480 UUMW
listed, all other CMEZ speakers are UL1480 UEAY listed. BGM series not UL listed)
© 2011 SoundTube Entertainment, Inc. All rights reserved. PN INS-CMEZ2S Rev07.05.11
Warning Warning
SoundTube speakers must be installed by a professional audio installer/contractor. For safety and for optimum
audio performance, installer must follow all directions issued by SoundTube Entertainment.
Installation aid/paint mask
Grille
Grille safety restraint
1.435.647.9555
Do not spec or install speaker near support beam, ventilation duct or other
structure that may interfere with speaker function or dispersion.
|
800.647.TUBE
|
www.soundtube.com
9. Select the tap position by
adjusting rotary switch
to desired high impedance
value or voice coil direct
mode.
1.
2.
9. Attach grille safety clip by
placing the large end of the
clip over snap-t post (1), then
sliding clip until small end
snaps into place around post
(2).
1.435.647.9555
11. Done!10. Press grille into place.
|
800.647.TUBE
1.
2.
9. Select the tap position by
adjusting rotary switch
to desired high impedance
value or voice coil direct
mode.
9. Attach grille safety clip by
placing the large end of the
clip over snap-t post (1), then
sliding clip until small end
snaps into place around post
10. Press grille into place.
(2).
|
www.soundtube.com 1.435.647.9555
11. Done!
|
800.647.TUBE
|
www.soundtube.com
9. Select the tap position by
adjusting rotary switch
to desired high impedance
value or voice coil direct
mode.
1.
2.
9. Attach grille safety clip by
placing the large end of the
clip over snap-t post (1), then
sliding clip until small end
snaps into place around post
(2).
10. Press grille into place.
1.435.647.9555
11. Done!
|
800.647.TUBE
|
www.soundtube.com
Loading...