Soundtube CM400i User Manual
Install Instructions For:
CM400i, CM500i, CM590i, CM600i, CM690i, CM800i & CM890i speakers
Strain relief (not included) may
be used with cover plate.
Cover plate
Euroblock connector
Signal wire
Ceiling thickness tolerances
Max
42.9 mm (1.69 in)
Cover plate clamping screw
Min
6.4 mm (0.25 in)
Tile bridge
Seismic restraint anchor tab
Ceiling tile
Euroblock jack
Speed Wing™ mounting arms
Baffle
Styrofoam installation aid/paint mask
Grille and bezel
seismic restraint
Grille and bezel
Box contents
1 Speaker
1 Euroblock connector
1 Grille and bezel
1 Styrofoam installation aid/paint mask
1 Cover plate
1 Tile bridge
CM400i, CM500i, CM600i, CM690i, CM800i, CM890i – UL listed 1480 & 2043
1.435.647.9555
© 2009 SoundTube Entertainment, Inc. All rights reserved. PN INS-CMI Rev05.26.09
Warning Warning
SoundTube speakers must be installed by a professional audio installer/contractor. Fo r safety and for
optimu m au dio performance, installe r must follow all direc tions issued by SoundTube Entertainment.
Do not spec or install speaker near support beam, ventilation duct or
other structure that may interfere with speaker function or dispersion.
|
800.647.TUBE
|
www.soundtube.com
Droptile Ceiling Install Instructions For:
CM400i, CM500i, CM590i, CM600i, CM690i, CM800i &CM890i speakers
1. Unpack speaker & set
aside grille assembly.
5. Insert speaker into
mounting hole on ground
with installation aid in
place. Screw down both
bolts on the baffle face to
actuate the mounting wings.
Firmly secure both bolts –
do not over-tighten.
Put
assembly into tile grid.
2. Keep Styrofoam
installation aid/paint
mask attached to
speaker until speaker
installation is complete.
6. Thread signal wire through
cover plate. Connect signal
wire to 4-pin Euroblock plug.
Tighten unused terminal
screws. Use inside positive
and negative inputs for either
voice coil or distributed
systems. For daisy chaining,
use outside positive and
negative terminals.
3. Use included tile bridge
to mark cutout in tile.
7. Insert the Euroblock plug
into the Euroblock jack on
rear panel of speaker and
replace cover plate.
For UL-compliant installations
strain relief (not supplied) may
be inserted into hole in cover
plate.
4. Use Rotozip or other tool
to cut hole.
Hole Diameters
CM500i & CM590i
228.6 mm (9.00 in)
CM600i, CM800i & CM801i
325.1 mm (12.80 in)
. If required, attach the
seismic restraint system to
the sheet-metal tab on the
rear panel of the speaker
(safety cable not included).
9. If you are not painting the
ceiling, remove & discard the
paint mask.
10. If you are painting the
ceiling after the speaker is
installed, leave the paint mask
in place until paint is dry.
11. Select the tap position
by adjusting rotary switch
to desired high impedance
value or voice coil bypass
mode. Switch is preset to
maximum tap setting in
70.7 V mode (33 W or 66 W).
12. Attach grille & bezel
seismic restraint to baffle
with provided screw.
1.435.647.9555
13. Attach grille – position the
grille over the baffle and allow
magnets to attract grille into
place. Be sure grille is properly
centered over baffle.
|
800.647.TUBE
SoundTube also provides optional Pre Construction Brackets & Architectural Grilles for the CMi product line.
Installation instructions for these accessories are included with specific accessory packaging.
|
www.soundtube.com
Loading...