Soundtube CM31-EZ User Manual
CM31-EZ
Install Instructions For:
CM31-EZ speaker
CM31-EZ
Drop-tile Installation Instructions For:
CM31-EZ speaker
1.435.647.9555
|
800.647.TUBE
|
www.soundtube.com
CM31-EZ
Sheetrock Installation Instructions For:
CM31-EZ speaker
1.435.647.9555
|
800.647.TUBE
|
www.soundtube.com
CM31-EZ
Pre-Construction Bracket Instructions For:
CM31-EZ speaker (Pre-construction bracket sold separately)
1.435.647.9555
|
800.647.TUBE
|
www.soundtube.com
Tile bridge
Baffle
Speaker seismic restraint hole
SpeedWing™ mounting arms
Installation aid/paint mask
Signal wires
Flexible conduit clamp
1. Unpack speaker. Leave
paint mask in place until
after speaker is installed or
painting is complete. Tile
bridge ships in separate box.
5. Feed speaker wires
through conduit clamp and
connect with wire nuts.
Push wire nuts into backcan
and affix conduit clamp.
2. Use included tile bridge
to mark cutout on tile.
6. If required, attach seismic
restraint system to hole in
clamping arm, then to
reinforced structure (safety
cable not included).
3. Use RotoZip or other tool
to cut hole. Hole diameter:
5.6 in. (142 mm).
7. Remove paint mask
unless painting is required.
In that case, follow steps
8-11 when painting is
complete.
4. Insert speaker into
mounting hole on ground
with tile bridge and paint
mask in place. Tighten both
screws on the baffle face to
actuate the mounting wings.
Firmly secure both screws,
DO NOT OVERTIGHTEN.
Put assembly into tile grid.
8. Adjust tap switch to
proper setting. Switch is
preset to the highest setting
in the 70.7-volt mode.
1. Unpack speaker. Leave
paint mask in place until
after speaker is installed or
painting is complete.
5. If required, attach seismic
restraint system to hole in
clamping arm, then to
reinforced structure (safety
cable not included).
2. Use included tile bridge
to mark cutout on
sheetrock. Tile bridge ships
in separate box.
6. Insert speaker into
mounting hole with paint
mask in place. Tighten both
bolts on the baffle face to
actuate the mounting wings.
Firmly secure both bolts,
DO NOT OVERTIGHTEN.
3. Use RotoZip or other tool
to cut hole. Hole diameter:
5.6 in. (142 mm).
7. Remove paint mask
unless painting is required.
In that case, follow steps
8-11 when painting is
complete.
4. Feed speaker wires
through conduit clamp and
connect with wire nuts.
Push wire nuts into backcan
and affix conduit clamp.
8. Adjust tap switch to
proper setting. Switch is
preset to the highest
setting in the 70.7-volt
mode.
1. Nail or screw bracket to
joists.
5. Feed speaker wires
through conduit clamp and
connect with wire nuts.
Push wire nuts into backcan
and affix conduit clamp.
2. Finish installing ceiling.
6. If required, attach
seismic restraint system to
the sheet-metal tab on the
rear panel of the speaker,
then to reinforced structure
(safety cable not included).
3. Use RotoZip or other tool
to cut hole.
7. Insert speaker into
mounting hole. Tighten both
bolts on the baffle face to
actuate the mounting wings.
DO NOT OVERTIGHTEN.
4. Unpack speaker. Leave
paint mask in place until
after speaker is installed or
painting is complete.
8. Remove paint mask
unless painting is required.
In that case, follow steps
9-12 when painting is
complete.
Grille safety clip
Box contents
1 Speaker
1 Grille
1 Paint mask
2 Wire nuts
1 UL-listed conduit clamp
Note: Tile bridge included, ships in separate box.
CM31-EZ
© 2009 SoundTube Entertainment, Inc. All rights reserved. PN INS-CM31-EZ Rev10. 26.09
Warning
SoundTube speakers must be installed by a professional audio installer/contractor. Fo r safety and for
optimu m au dio performance, installe r must follow all direc tions issued by SoundTube Entertainment.
Grille
1.435.647.9555
|
800.647.TUBE
|
www.soundtube.com
Warning
Do not spec or install speaker near support beam, ventilation duct or
other structure that may interfere with speaker function or dispersion.
1.
2.
9. Attach grille safety clip by
placing the large end of the
clip over snap-fit post (1),
then sliding clip until small
end snaps into place around
post (2).
10. Align tabs on snap-fit
grille with slots in baffle,
gently press grille into place.
1.
2.
11. Done! 11. Done! 12. Done!9. Attach grille safety clip by
placing the large end of the
clip over snap-fit post (1),
then sliding clip until small
end snaps into place around
post (2).
10. Align tabs on snap-fit
grille with slots in baffle,
gently press grille into place.
9. Adjust tap switch to
proper setting. Switch is
preset to the highest setting
in the 70.7-volt mode.
1.
2.
10. Attach grille safety clip
by placing the large end of
the clip over snap-fit post (1),
then sliding clip until small
end snaps into place around
post (2).
11. Align tabs on snap-fit
grille with slots in baffle,
gently press grille into place.
Loading...